Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
IE was using a wrench to remove an oil filter off of a 24M during regular PM. EE was wearing rubber gloves when their finger got pinched between the wrench and a piece of metal. Injury required stitches
EE was trying to free a stuck dump rope, was using prybar and slipped and hit EE in the mouth.
Employee was installing an I-beam to tie the revolving frame to the tub base and was using a hammer to tap the I-beam into place. EE struck middle finger of left hand with the hammer and fractured the tip of finger.
Miner along with 3 others were changing 736 dragline bucket. While removing the last trunnion link pin. EE struck the pin, not hitting it hard. A piece of metal ½"W x 1/4"H broke away from the Wilcox hammer, striking the miner in the left side of belly. Leaving laceration approximately 1/2" across. Surgery was required to remove the piece of metal. Resulting in lost work days.
2/25/2020 Miner was hammering 6" pipe apart and pulling and felt something in EE's rt. elbow. It was determined to be an unspecified strain on 2/28/2020 by Dr. EE was treated with Ice and OTC meds on. 6/10/2020 went back continuing problems it was determined with to be a torn muscle at would require surgery on 6/23/2020. The miner worked EE's duties up until 6/23/2020.
Miner was removing a wedge from dragline socket struck it with 20lb hammer. Piece of steel chipped off and embedded in lower lip was removed. No sutures needed Tetanus shot was administered.
Miner was stripping 15kV 350MCM cable with a utility knife, ee slipped with left hand while stripping the insulation and received a laceration left 1st index finger, and 5 sutures were needed.
Miner received a laceration between on the left hand between the thumb and pointer finger. The miner was attempting to pry a socket of a impact wrench an slipped. resulting in three stitches.
Dragline operator and oiler were putting a timber back in place under the drag cable. Oiler was using a pry bar on a timber The timber slid on the pry bar and pinched the top of the 4th little finger midpoint between the top of the finger and 1st knuckle on the right hand of the operator. Approximately 3/16"of the finger was amputated mid point of the nail.
EE was removing bearing of swing shaft cut bearing with torch, hit bearing with hammer. Sliver of steel flew off striking him in left thigh penetrating jeans and coveralls. He was taken to clinic. He was sent back to work no Meds/Restrictions/removal of piece. 11/15/13 piece of steel moved and was removed by clinic Fri 11/15/13. Informed 11/18/13 back to work No LTA/Restrictions.
Mechanic was working in a access hole on a D11-R dozer repairing an implement pump. He was in awkward position loosening a bolt. He pulled a muscle in his left shoulder.
Dragline operator was doing rapairs on the rigging and cleaning out some frozen dirt from the drag socket with a 2' pry bar. He was pushing at it to loosen the frozen dirt. The bar glanced off, striking him behind his steel toe boot on the left foot. Injury was a laceration behind the small toe, recieved 5 sutures.
Employee was helping to replace a swing transmission, it was hanging crooked. They hooked a come-along to it to help level it as they lowered the transmission. The come-along swung the transmission to the side pinching the employees thumb between the shaft and a bolt. Employee continued to work, blood was drained the next day from thumb nail bed.
EE WAS HELPING TO RESOCKET DRAGLINE CABLE. WHEN A CABLE SOCKET WEDGE WAS LIFTED INTO THE CABLE SOCKET, THE WEDGE BECAME UNBALANCED, AND THE WIRE ROPE SLING SLIPPED AND PINCHED HIS FINGERS, FRA CTURING THE RIGHT RING FINGER ABOVE THE MIDDLE JOINT AND SEVERING THE RIGHT LITTLE FINGER TIP.
EMPLOYEE WAS REPAIRING A LOAD COUNTER AND WAS CUTTING THE TAIL OFF A NYLON TIE STRAP WITH A UTILITY KNIFE. THE KNIFE EITHER SLIPPED OR CUT THROUGH STRAP AND RAN THE BLADE INTO HIS LEFT WRIST. HIS WRIST REQUIRED 3 STITCHES.
EMPLOYEE WAS LOWERING AND GUIDING SWING SHAFT INTO PLACE, WHEN THE SHAFT CAUGHT ON SOMETHING. ITMOVED TOWARD EMPLOYEE AND HE STEPPED BACK OFF OFTHE GEAR CASE AND STRAINED LEFT ANKLE.
EMPLOYEE WAS PUTTING A 31/2INX24IN BOLT IN A BEARING CAP HE USED A PRY TO LIFT THE BOLT UP & HE WAS PLACING A SPACER UNDER THE BOLT THE BAR SLIPPED & THE BOLT FELL & PINCHED HIS FINGER
EMPLOYEE AND A MECHANIC WERE REPAIRING AN OIL LEAK UNDER A SCRAPER USING A PRY BAR TO HOLD HOSES BACK AND THE MECHANIC RELEASED THE BAR AND THE EMPLOYEE NEVER GOT A HOLD ON THE BAR AND IT STRU CK THE EMPLOYEE IN THE CHEEK AND RESULTED IN A CUT THAT NEEDED THREE STITCHES.
EMPLOYEE WAS PUTTING A TOOTH ON A RIPPER SHANK FROM A D-10 CAT WHICH HAD BEEN WELDED UP IN THE WELDING SHOP. THE TOOTH WOULD NOT FIT SO EMPLOYEE USED A 12 LB HAMMER AND STRUCK THE TOOTH TO DR IVE IT INTO PLACE. A CHIP OF STEEL FROM THE TOOTH HIT HIM IN THE LEG. EMPLOYEE REPORTED ON FEB. 13 HE HAD BEEN TO DOCTOR TO HAVE CHIP REMOVED.
EMPLOYEE WAS PUSHING ON A WRENCH AND ANOTHER EMPLOYEE WAS PULLING ON THE WRENCH. THEIR HANDS SLIPPED OFF THE WRENCH AND HIT THE INJURED EMPLOYEE IN THE RIBS. THEY WRE TIGHTENING A BOLT ON THE SWING SHAFT.
EMPLOYEE WAS INSTALLING A PIN IN THE SPINDLE OF A 16G MOTOR GRADER USING A HAMMER TO DRIVE THE PIN IN PLACE. A CHIP OF STEEL FROM THE PIN STRUCK HIM IN THE ARM ABOVE THE WRIST.