Buscar en el registro

Employee was position under the dozer, removing outer equalizer pin with drift punch and a maul. On the backswing the maul hit the coil diverting the hammer backswing into upper lip.

Employee was removing a loader bucket tooth. In the process of using a sledge hammer to strike the tooth. Metal debris hit the employee in right leg thigh.

Employee was removing a railroad spike with a spike puller bar. His pointer finger was smashed between the bar and steel rail, as he pushed down on the bar.

The wrong tool for the task, a long handled sledge hammer (10lb) was used to set railroad spikes for the spike driving crew following. The primary hazard was not identified during the SLAM Process. The employee also got complacent and lost focus of hand placement. The result, the employee lost the index finger nail and recieved 3 sutures.

Employee was removing a steering cylinder from a Letourneau loader. Both pins were removed and had a come-a-long installed to assist in lowering the component down. The lifting strap was installed somewhere in the middle of the str cylinder barrel. When the steering was rocked loose from position the cylinder swung and crushed the left hand of the employee.

Metal shavings embeded into welder's left eye while replacing an equalizer pin on a dragline bucket.

Employee fractured thumb with a 10# sledge hammer when pounding in railroad clips.

A hook on a come-along that an employee was using broke from its hooked postion and hit the employee on the lip and nose.

Employee was in the process of checking the gap between a dozer push arm and a trioun with a pry bar. The weight of the push arm pulled the pry bar, which then jerked the employee's arm.

Maintenance D employee was struck on the right hand above the knuckle by a hand crank pump pulley handle as he was raising the pump.

Employee sustained injury to left thumb (open wound & fracture) by pinching thumb between the mast and adjusting tool at completion of drill repair.

While lining up ties, employee hit the top of his foot with a six foot long bar.

Ee was using a pry bar to put rims together on the Kress truck tires. EE pinched his left thumb between the rim and the pry bar causing a laceration of 1/2" resulting in 3 stitches.

EE was in process of using a come-along to move a piece of metal plate associated with the #1 crusher screen. As he reached under the screen to unhook the come-along the metal plate slid and pinched two of his left fingers, which resulted in 3 stitches on his left index finger. The extra slack in the chain stopped the metal from falling fully onto this fingers.

The EE was working on a pulling fixture for removing a pin when he felt a pain in his left eye. The EE was chipping a weld with a chipping hammer. Subsequently, a metal particle became lodged in his left eye. He was wearing required PPE.

WHILE TIGHTENING A BOLT NEAR THE HYDRAULIC LINE ON TRD5321 DOZER, EE HIT THE COOLANT HOSE CAUSING THE ANTI-FREEZE FROM THE HOSE TO DRIP INTO HIS LEFT EYE. HE SUSTAINED CORNEAL ABRASION IN HIS EYE. HE RECEIVED FURTHER MEDICAL CARE AND RETURNED TO FULL DUTY ON NOVEMBER 5, 2002.

EE SUSTAINED LACERATIONS TO HIS RIGHT PALM WHICH REQUIRED 7 SUTURES STITCHES. EE WAS ASSISTING IN A ROPE CHANGE AT THE 8750 DRAGLINE. THE EE WAS LIFTING UP THE WIRE ROPE ON THE DRUM WITH A DEF ECTIVE PRYBAR WHEN THE END OF THE BAR WAS FORCEDINTO HIS PALM CUTTING THROUGH HIS RUBBER GLOVES WHICH WERE DEEMED AS INADEQUATE PERSONAL PROTECTIVE EQUIPMENT.

WHILE CUTTING OPEN A WATERMELON DURING LUNCH, EE'S RIGHT HAND SLIPPED AND CUT INTO HIS INNER LEFT WRIST. EE SUSTAINED A 1 1/4" INCH LACERATION REQUIRING FOURT STITCHES.

WHILE MOVING SERVERS, JONNA WAS USING A SMALL KNIFE TO CUT WIRE TIE WRAPS FROM CABLES. THE KNIFE SLIPPED AND CUT HER LEFT THUMB. SHE RECEIVED MEDICAL TREATMENT (2 SUTURES).

WHILE DRIVING A SURVEY STAKE IN THE REGARDE AREA SOUTH OF BARBER RAMP 5 HE POUNDED THE LATHE WITH A HAMJER AND A PIECE OF SPLINTERED OFF AND WENT THROUGH HIS LEFT HAND IN THE AREA BETWEEN THE THUMB AND INDEX FINGER. STITCHES WERE REQUIRED.

WHILE DISASSEMBLING LEFT SIDE OF THE UPPER BELL CRANK PING, EE S RING FINGER AND PINCKY WERE CUT ON RIGHT SIDE HAND. HE WAS STANDING ON THE LADDER HITTING THE PIN WITH THE HAMMER TO DRIVE IT O UT AND THE OUTSIDE BUSHING POPPED OUT HITTING EE'S HAND.

IN AN INCIDENT WHICH OCCURRED ON 11/12/99, THE EE ALLEGES THAT HE RECEIVED AN INJURY REQUIRING SURGERY. HE HAS WORKED FULL-TIME UNTIL THE SURGERY ON 3/22/00. WORKER'S COMP HAS AGREED TO HONOR THIS AS A WORK INJURY, BUT THE DATE IS GIVEN AS 3/22/00.

EE AND TWO CO WORKERS WERE IN THE PROCESS OF LOSOSENING CAKED ON AMMONIA DITRATE FROM THE BLOCK-B SILO WHEN A LARGE CHUNK FELL INTO THE MIX TRUCK BIN. HE USED A BENT METAL ROD TO LOOSEN THE LA RGE PIECE. THE METAL ROD TWISTED IN HIS HAND. STRIKING HIS RIGHT TEMPLE NEAR THE EYE AND LACERATING THE SKIN. THREE STITCHES WERE REQUIRED TO CLOSE THE WOUND.

THE EMPLOYEE WAS DISMANTLING A FLAT TIRE FROM THE RIM. HE PUSHED THE TIRES BEAD AWAY FROM THE LOCK RING. EMPLOYEE WAS IN THE PROCESS OF REMOVING THE LOCK RING WHEN HE STRUCK THE RING WITH HIS BAR TO LOOSEN THE LOCK RING.HE DIDN'T HAVE A GOOD HOLD ON THE BAR WHEN IT RECOILED BACK,STRIKING HIM IN THE MOUTH. EMPLOYEE SUFFERED A BUSTED LIP THAT REQUIRED TWO STITCHES.

THE EE HAD CLAMPED OFF A FUEL HOSE TO REPLACE A PRESSURE GAUGE. AS THE EE WAS RELEASING THE CLAMP, THE TOP JAW BROKE OFF. THE BROKE JAW RICOCKET OFF THE FUEL TANK AND STRUCK THE EE S RIGHT EAR CAUSING ABOUT A ONE INCH LACERATION.

EE WAS STRIKING THE LOWER BEARING ON THE #1 SWING SHAFT WITH A 20# SLEDGE HAMMER WHEN A SLIVER CAME OFF THE BEARING & LODGED IN THE EE'S INNER LEFT LEG. THIS OCCURRED IN THE REVOLVING FRAME OF THE 7920 MARION DRAGLINE.

UPON REMOVING A DISABLED MOTOR FROM ITS MOUNTS, INJURED AND A CO-WORKER PROCEEDED TO THE MOTOR ON TO AN IRON ROD WITH AMYLONG ROPE. THE IRON ROD WAS 1"X7' AND THE MOTOR TIED TO THE MIDDLE. W HILE CARYING THE MOTOR DOWN A FLIGHT OF STEPS, THE MOTOR SLIPPED DOWN THE ROD AND HIT THE INJURED ON THE RIGHT CALF. THE INJURED SUFFERED A BREAK TO THE TIBIA AND TWO BREAKS ON THE FIBULA.

EMPLOYEES WERE ATTEMPTING TO SECURE RAILROAD TRACKS TO A TRACTOR TRAILER TRUCK WITH CAMMING LOADBINDER. A PIPE WAS INSERTED OVER THE HANDLE AS A LEVER. AS EMPLOYEE WAS TRYING TO REMOVE PIPE FR OM THE HANDLE OF THE BINDER, THE HANDLE SPRUNG LOOSE STRIKING INJURED ON THE LEFT WRIST, CAUSING A HAIRLINE FRACTURE OF THE TRAPEZIUM.

WHILE USING A PRY BAR TO LOOSEN THE WHEEL TO THE 5175 RECLAIMER GEAR BOX INJURED SMASHED HIS LEFT THUMB BETWEEN THE PRY BAR AND THE CENTER OF THE GEAR BOX WHEEL.

WHILE ASSISTING A MECHANIC IN REPLACING SWING MOTOR COUPLING BOLTS ON THE 8050 DRAGLINE, HE WAS REMOVING THE BOLTS WITH A FIVE FOOT PRY BAR. WHILE REPOSITIONING THE PRY BAR, HE STRUCK HIS LEFT KNEE CAP WITH A GLANCING BLOW.

WHILE INSTALLING THE SNOW PLOW ON LOD-7, INJURED LEFT FINGER WAS CAUGHT BETWEEN THE BOLT AND THESNOW PLOW. INJURED ONE STITCH TO HIS LEFT INDEX FINGER.

WHILE REPLACING TRACKS ON THE DOZER, THE EMPLOYEE WAS USING A 20LB SLEDGE HAMMER TO POUND THE TRACKS WHEN A PIECE OF METAL FRAGMENT SHIPPED OFF THE TRACKS CAUSING A PUNCTURE WOUND TO HIS LEFT THIGH.

THE EMPLOYEE WAS ALIGNING THE TRACK ON A DOZER WITH A SLDGE HAMMER WHEN HE HIT THE EDGE OF THE TRACK. A 1/4 IN. PIECE OF TRACK FRACTURED LOOSE AND ENTERED HIS LOWER RIGHT FOREARM.

THE EMPLOYEE WAS WORKING ON A OVERHEAD CABLE STAND HE CUT OUT 1 1/2IN MILD STEEL PLATE TO REINFORCE THE PLATFORM AFTER CUTTING THE 1 1/2IN PLATE EE WAS CLEANING THE SLAG OFF THE PLATE WITH A C HIPPING HAMMER THE EMPLOYEE ALLEGED DURING THE CLEANING PROCESS A SMALL PIECE OF SLAG HIT HIS RT EYE

INSTALLING A BELLY PAN FOR 980C USING FIVE TON FLOOR JACK. THE HANDLE OF THE JACK CAME LOOSE & FELL ON LEFT HAND - SMASHING THE RING FINGER.

EMPLOYEE WAS DRIVING ON C-CLIPS ON THE RAILS HE ALLEGED HE WAS HOLDING THE CLIP WITH LEFT HAND & USING RIGHT HAND TO SWING A 10 LB. HAMMER. WHILE DRIVING ON THE CLIP THE HAMMER CAME OFF END O F THE CLIP & CAME UP & HIT HIS MIDDLE FINGER.

THE EMPLOYEE WAS CHANGING OUT THE MUD FLAPS ON TRW-288 TRAILER. WHILE CUTTING THE MUD FLAPS THEKNIFE ACCIDENTALLY SLIPPED & PENETRATED HIS RIGHT LEG. THE EMPLOYEE WAS CUTTING TOWARDS HIMSELF WHEN THE INCIDENT HAPPENED.

EMPLOYEES AHD CHANGED OUT THE INTERMEDIATE SUSPENSION CABLES ON THE MAST OF HT E8050 DRAGLINE AND REPLACED IT WITH NEW ONE SAND WERE IN THE PROCESS OF PINNING THE LAST CABLE. THE EMPLOYEES HA D PLACED A CHAIN AROUND THE SUSPENSION CABLE AND FASTENED IT TO A WINCH CABLE TO REMOVE ANOTHER CHAIN. AS THE SUSPENSION CABLE WAS WINCHED INT HE CHAIN BROKE, SNAPPING BACK AND STRUCK THE EM

THE EE WAS USING A PORT A POWER 20 INCH RAM WHICH WAS RESTING ON TWO SUPPORT BLOCKS. THE BLOCKS KICKED OUT FROM UNDER THE JACK. CONSEQUENTLY ONE BLOCK STRUCK THE EE FACE AND THE OTHER BLOCK LA NDED ON HIS LEFT HAND. THIS CAUSED A LACERATION ON HIS LEFT HAND RING FINGER.

THE EE WAS IN THE PROCESS OF CUTTING OFF THE TOP PORTION OF A PLASTIC BUCKET WITH A UTILITY KNIFE WHEN THE KNIFE SLIPPED OUT OF THE BUCKETY AND CUT HIMSELF ON THE RIGHT THIGH. EE WAS TAKEN TO A MEDICAL CLINIC WHERE HR RECEIVED TWO STITCHES AND RELEASED TO RETURN TO WORK.

EMPL WASHING DOWN COAL DUST IN TUNNEL #2 WHEN MUD SPLASHED INTO RIGHT EYE.SEEN BY EYE DR 3-16 SEVERAL PIECES OF COAL DUST WERE REMOVED. EMPL WAS RELEASED TO GO BACK TO WORK.

INJURED WAS TIGHTENING A UNISTRUT CLAMP BOLT NUT WITH A CRESCENT WRENCH WHEN THE WRENCH SLIPPED AND INJURED STRUCK HIS FOREARM AGAINST THE EDGE OF THE UNISTRUT CAUSING A 1/2" LACERATION.INJURE D WENT TO THE CARE PROVIDER WHERE HE RECEIVED TWO SUTURES TO CLOSE THE WOUND.

WHILE RECRIBBING TWO(2) 250-TON HYDRAULIC JACKS USED AT THE 8050 DRAGLINE REPAIR A COME-A-LONG HANDLE STRUCK A HYDRAULIC PIPE FITTING & CAUSED IT TO BREAK I NAME WAS STANDING APPROX 6FT FROM J ACK WHEN HYDRAULIC FLUID SPRAYED INTO HIS FACIALAREA & GOT HYDRAULIC FLUID INTO HIS EYES

INJUIRED WAS REPAIRING A DAMAGED JACKET ON A 500 MCM CABLE. HE WAS TRIMMING AWAY THE DAMAGED JACKET WITH A KNIFE, LOST GRIP ON THE RUBBER CAUSING A SUDDEN MOVEMENT OF HIS HAND TOWARD THE KNIF E, RESULTING IN A CUT ON HIS LEFT HAND, LEFT THUMB WHICH REQUIRED 4 STITCHES TO CLOSE THE WOUND.

POSITIONING NYLONG STRAP TO REMOVE CYLINDER FROM LDW HAND CAUGHT BETWEEN CYLINDER AND MAIN FRAME WOUND AND CONTUSION TO R INDEX MIDDLE AND RING FIN GERS

EMPL WAS ASSIGNED TASK TO TORQUE & LOCK WIRE CENTER PINION BEARING RETAINER CAPSCREWS. HE HAD COMPLETED TORQUEING CAPSCREWS & EMPLS BEGAN TIE WIRING STRUCK TO EMPL IN RIGHT EYE CASUING SMALL C UT. HE WASHED EYE WITH BUFFERED EYE ALERT. DR REPORTED EYE INJURY WAS MINOR & EMPL NEED NOT MISS WORK.

WHEN CHANGING BIT ON DRILL STEEL USING A BIT CHANGING HAMMER HE STRUCK THE BASE OF THE MAST WHEN DR EXAMINED XRAYED SHOWED FX TO THE TIP OF THE MIDDLE FINGER

THE CHAIN WRENCH SLIPPED ON THE SHAFT OF THE MG SET, THE WRENCH CAME DOWN ON THE EDGE OF THE EDGE OF THE MG SET PEDESTAL WHEN FINGER WAS CAUGHT BETWEEN THE WRENCH AND THE PEDESTAL.

I.NAME CUT THROUGH TAPE CONNECTION BEFORE BEGINNING 2ND TAPE CONNECTION.HELD MOTOR LEAD WITH LEFT HAND AND CUT THROUGH TAPE WITH RIGHT HAND.UTILITY KNIFE WENT THROUGH TAPE AND WITH SAME MOTION ,CUT HAND BETWEEN THUMB AND 1ST FINGER.

WRENCH PINCHED THE TIP OF THE RT.RING FINGER AGAINST THE REVGOLVING FRAME EMPLOYEE WENT TO SEE DOC.ON 6TH OF JAN. DOC.FOUND A SIMPLE FX.AT THE TIP OF FINGER AFTER XRAY RX WAS PRESCRIBED