Buscar en el registro

While breaking boulders with excavator and hydraulic hammer a piece of rock came back and hit the boom of the excavator and bounced off hitting the window & breaking it. The broken glass cut the right forearm of the operator.

EE was assisting operation and placed finger on shim; finger was pinched causing a fracture and laceration of the left index finger tip requiring two sutures. Employee released to work without restrictions.

Miner experienced lower back pain while excavating sample material holes. Excavator occasionally hit hard material which caused a jarring sensation when front end of excavator would lift off the ground & land back down once bucket became free. Miner requested to visit WC Doctor on 8/10/18 due to lower back pain not subsiding. Physician placed miner on light duty.

Windshield wiper repair in progress. Turned wiper motor on to line up pin on sprocket with linkage. Sprocket rotated and pinched middle finger between the linkage and housing. Employee disregarded company policy and training on lockout/tagout procedures. Employee received 16 stitches to the left middle finger. No impairment, released for normal duty as a driller.

Employee sustained burn to right ankle when a piece of slag fell into a crease in jeans on top of boot trim; slag burned through the material and dropped down into the boot while performing welding repairs. Physician placed employee on 'off work' status.

Employee reported eye irritation, was taken to the clinic, employee had debris in right eye which required mechanical removal. Employee was released to return to work at full duty without restriction.

Employee was performing a belt splice, had a hand grinder in one hand and he was moving forward on the belt. The employee went to brace himself and hit the safety switch on the grinder powering the tool which cut his hand (7 stitches).

Employee was cutting welds to remove a cover plate to access the inside of a conveyor receiving box. Employee was using a grinder with a cutting wheel when the grinder kicked back striking and knocking off his hard hat and attached face shield. The wheel then struck the employees cheek causing a laceration from the edge of his lip to his cheek approximately 2.5 inches in length.

Worker was removing a bolt using a wrench and impact gun. Nut stuck and the force of the impact gun forced the wrench down and pinched off the tip of his finger

EE was grinding with a portable grinder, when the wheel slipped off the work surface and his forearm contacted a sharp edge of the conveyor frame.

Mud pump on clarifier exploded while EE was relieving preasure from top of pump causing hot rock and mud to splash on EE face and left arm. EE had light burns on face and 2nd degree burns on left forearm.

Employee was holding impact gun over his head to conduct maintenance on horizontal crusher. While doing this, he strained right shoulder.

EE was using gas welding torch to perform maintenance on conveyor, when a piece of hot slag entered around his wrap-around safety glasses and contacted his left eye.

While preparing to assist a 3rd party trucking company to load their damaged transfer trailer onto a flatbed our employee was injured. The transfer box fell off of the trailer ejecting our employee pinning him underneath the upside down transfer box.

MALFUNCTION OF THROTTLE CABLE ON 16H BLADE.

HOLDING STEEL BARS WHILE ANOTHER EMPLOYEE WELDED. FLASH BURN TO EYES.

EMPLOYEE ALLEGEDLY WAS BUMPED EXTRA HARD BY A PUSH CAT DOZER. EMPLOYEE WAS OPERATING CAT 631 SCRAPER REMOVING OVERBURDEN.

EE USING HAND-HELD POWER TOOL WITH WIRE BRUSH WHEEL. HE WAS CLEANING OLD METAL PARTS. EE WEAR ING SAFETY GLASSES AND FACE-SHIELD FELT SOMETHING IN HIS EYE WHILE DRIVING HOME AFTER SHIFT.

EMPLOYEE WAS WELDING IN AN OPEN AREA WITH SOME LIGHT WIND. SPARKS ARCED CAUSING A FLASHBURN TO BOTH EYES.

REMOVING MOTOR WHILE USING A CRANE, EMPLOYEE PUSHED ON THE MOTOR TO FREE IT. THEN THE MOTOR SWUNG BACK AND SMASHED FINGER AGAINST STEEL FRAME.

DIRT IN EYE WHILE WORKING ON CRUSHER.

AFTER CUTTING POLYLINERS FOR THE GRIZZLY WITH A SKILL SAW, HE RETRACTED HIS BODY OVER THE LENGTHOF THE LAST CUT. THE SAW WAS OUT OF THE CUT, ON ITS SIDE WITH GUARD FULLY EXTENDED. HIS HAND & FINGER WERE PLACED OVER THE TRIGGER BUT THE SAW WAS NOT IN MOTION, AS HE RETRACTED THE SAW WAS ACTIVATED & CUT INTO HIS KNEE.

WHILE LOOSENING A BOLT WITH AN IMPACT WRENCH THE BOLT SPUN AND CUT EMPLOYEE'S LEFT MIDDLE FINGER. FINGR REQUIRED STITCHES. EMPLOYEE WAS NOT WEAR GLOVES.

OPERATOR WAS RIPPING W PIT. WHILE LOOKING BACK OVER RIGHT SHOULDER AT RIPPER. THE DOZER TRAVELED OVER A HARD HUMP WHICH CAUSED THE DOZER TO ROCK FAST SIDE TO SIDE JERKING THE OPERATORS HEAD AN D NECK.

WELDING WHEN A FOREIGN OBJECT ENTERED HIS EYE.

EE FAILED TO INSPECT GAS HOSES PRIOR TO PERFORMING CUTTING OPERATION.

EE WAS OPERATING ROCK HAMMER AT TOCK CRUSHER. EE STEPPED AWAY FROM CONTROL BOOTH TO CHECK NOISE. ROCK HIT EE IN BACK OF HEAD.

EE WAS ASSITING WELDER FABRICATING A BUNKER. EE RECEIVED AN APPARENT ARC FLASH CAUSING UV KERATITIS WHICH BECAME NOTICABLE AFTER HE ENDED HIS SHIFT.

PLANT SUPERINTENDANT HAD FINGERS IN SLOT ON LID OF IMPACT CRUSHER PULLING ON LID TO ALIGN SLOTS TO DOGGING POSTS AS LID WAS BEING LOWERED HYDRAULICALLY. RIGHT HAND INDEX AND MIDDLE FINGER WERE CRUSHED WHEN LID MADE CONTACT WITH DOGGING POSTS.

EMPLOYEE WAS USING A CUTING TORCH WHEN A PIECE OF SLAG BLEW INTO HIS EYE.

EMPLOYEE WAS USING A CUTTING TORCH TO CUT A TAIL PULLEY. HE STATED A PIECE OF SLAG STRUCK HIM IN THE EYE. HE STATED HE WAS WEARING EYE PROTECTION.

EE WAS ASSISTING WITH THE REMOVAL OF A DISCHARGEPIPE - WHEN THE PIPE WAS CUT FREE - THE DISCHARGE BOX FELL ON HIS THUMB. INJURY RESULTED IN A FRACTURE TO THE THUMB & SUTURES.

WHILE OPERATING A ROCK HAMMER AT ROCK CRUSHER A PIECE OF A ROCK CAME OUT OF CRUSHER JAW AND STRUCK EMPLOYEE ON RIGHT FRONT SIDE OF HEAD. EMPLOYEE WAS EXAMINED BY A DR AND RELEASED FOR MODIFIE D WORK. EMPLOYEE'S CONDITION CHANGED 1-5-96 AND WAS TAKEN OFF WORK.

EMPLOYEEW AS USING A SMALL RUBER HOSE TO WASH OFF MAGNETIC SEPARATOR DRUM AT ROCK PLANT. THE ROTATING DRUM CAUGHT THE TIP OF THE HOSE AND DREW EMPLOYEE'S THUMB INTO THE DRUM FLANGE AREA.

EE WAS WELDING &A PIECE OF SLAG BURNED HIS INDEX FINGER

OPERATOR WAS CHANGING THE DRAG CABLE ON DRAGLINE. HE CUT THE CABLE LOOSE FROM THE DRUM WITH A CUTTING TORCH. WHEN HE PULLED THE END THROUGH THE FAIRLEED, IT WRAP AROUND HIS LEG & THE HOT END B URNED HIM BEHIND THE KNEE. DUE TO INFECTION SETTING IN HE OBTAINED MEDICAL ATTENTION ON 11-9-94.

WHILE GRINDING ON THE SKIP LOADER SCRAPER A PIECE OF STEEL, MAY HAVE BEEN ON HANDS OR IN HIS EYE BROW NOT REALLY SURE BUT WENT INTO THIS EYE. HE WAS WEARING SAFETY GLASSES BUT NOT A SHIELD.

EMPLOYEE WAS CUTTING A PIECE OF ANGLE IRON THAT WAS ATTACHED TO A CONVEYOR - THE ANGLE IRON SNAPPED - THE CONVEYOR DROPPED 3" - 5" ONTO HIS HAND.

OPERATOR BACKED OVER BOULDER, WHEN HE CAME OVER TO TOP AND THE D10 SHIFTED, THE OPERATOR'S BACK WAS INJURED.

WHILE AIR ARCING EMPLOYEE WAS INSPECTING WORK; HE ROLLED HIS HAND & ARCED THE GOUGING CARBON TO THE HEAD WHILE PROTECTIVE HOOD WAS UP.

WHILE EXCAVATING THE OPEN PIT MINE EMBANKMENT,THE LOADER OPERATOR WAS EXPOSED TO APPARENT SOLVENT-TYPE CONTAMINATION.FUMES IRRITATED THE RESPIRATORY TRACT OF EMPL.

TRAVELING FORWARD RAN OVER WIND-ROW CAUSING EQUIPMENT TO ROCK WHICH CAUSED EMPL TO PLACE ALL OF HIS WEIGHT ON RIGHT ELBOW.ARM WAS SETTING ON ARM REST,CAUSING PAIN IN SHOULDER.

MAN HAD REPLACED SWITCH ON 4 1/2 HAND GRINDER WHEN HE WENT TO TEST NOW SWITCH HE PLUGGED IN GRINDER AND IT STATED WITH BACK OF FINGER BAGAINST GRINDING DISC SWITCH HAD BEEN LOCKED ON AND DISC GARD HAD BEEN REMOVED TO DO REPAIR AND NOT REPLACED.

EMPLOYEE SUFFERED FLASHBURN AS A RESULT OF NOT LOOKING AWAY AS OTHER WELDER STRUCK ARC.

REMOVING SNOW FROM ROAD WITH GRADER, OPER STALLED ENGINE GRADER SLID TO EMBANKMENT THE OPER JUMPED FROM MOTOR GRADER BERM STOPPED GRADER

EMPLOYEE WAS WELDING. DUST BLEW INTO EYES CAUSING CONJUNCTIVITIS REQUIRING MEDICAL TREATMENT.

WHILE RUNNING POWER DRILL THE MOTOR DRILL BIT CAUGHT IN MATERIAL AND KICKED DRILL HANDLE INTO OPERATORS LIP.

NUT STUCK IN SOCKET, STUCK FINGER INTO NUT TO GET OUT AND ACCIDENTLY HIT TRIGGER AND SCREWED NUT ONTO FINGER.

WORK CREW HAD REPLACED ROCK CRUSHER HEAD. THE HEAD WAS RESTRAINED FROM ROTATING BY A CHAIN WHICH WAS TEMPORARILY WELDED TO THE CRUSHER FRAME. THE CHAIN WELD BROKE WHEN THE CRUSHER MOTOR WAS ST ARTED. EMPLOYEE WAS STILL ON THE DECK AND WAS STRUCK ACROSS THE FRONT OF HIS LEGS BY LOOSE CHAIN.

REMOVING ROCK FROM S CREEN ROCK GOT LODGED HE WAS BELOW ROCK WHEN ROCK CAME THRU IT ROLLED ON L HAND