Buscar en el registro

EE was opening valve using electric valve wrench and pinched his finger, causing a laceration requiring sutures.

Employee was cleaning up using a shop vac and strained his lower back while stretching the hose out.

EE was using a drill press in under ground elec. shop when he finished hole he started extracting bit od metal plate he had drill handel in right hand it slipped out of hand when drill struck his tip of his left thumb got caught between chuck and base of drill press.

Employee was closing Warman valve using an electric valve wrench and got his finger pinched between the trigger on the valve wrench and a 6" pipe.

EE WAS RELIEVED BY ANOTHER ROOF BOLTER OPERATOR. THE OTHER OPERATOR THOUGHT EE HAD LEFT THE AREA BECAUSE WHEN HE MOVED THE BOLTER THE FIRST TIME, EE WAS AT THE BACK OF THE BOLTER. WHEN HE MOVED THE BOLTER THE SECOND TIME, EE WAS BY THE RIGHT FRONT TIRE. RAN OVER EE'S RIGHT FOOT - FRACTURE.

Ee was operating fct-3 in panela fm02. fct3 has a breaker caps on the front a rock ricohet off. another rock, coming out of breaker shaft striking ee in head.

EMPLOYEE WAS REPAIRING A HOSE ON JCM-5 IN PANEL SB15. ANOTHER EMPLOYEE WAS GOING TO LET COVER FOR AUGER JACK DOWN AND TOLD EVERYONE HE WAS GOING TO DO SO. WHEN HE DID THE HEEL BAR KICKED OUT STRIKING THE FIRST EMPLOYEE IN THE RIGHT FOREARM.

While roofbolting, slab of material fell and hit ee on left shoulder.

EMPLOYEE STATED HE WAS INSPECTING THE FEED BOX ON #5 DRYER WHEN ONE OF THE SPRINGS CAME OUT STRIKING EMPLOYEE ON LEFT CHEEK CHIPPING A TOOTH AND BRUISING CHEEK.

EMPLOYEE STATED HE WAS WORKING ON GR III IMPACTOR CHANGING ANVILS WITH AN IMPACT WRENCH. THE SOCKET SLIPPED OFF OF SWIVAL AND STRUCK LEFT MIDDLE FINGER CAUSING LACERATION REQUIRING SUTURES.

EE WAS TROUBLE-SHOOTING CENTRIFUGE MOTOR CUBICLE WHEN THE PRIMARY BUS STAB PHASE LEADS SHORTED PHASE TO PHASE.

EE IS A BEAVER BOLTER OPERATOR IN PANEL, WHILE BOLTING ON THE 1/2 PAS SIDE OF 2 ROOM 18 X CURTAIN PANEL, EE NOTICED A CRACK IN SEAM. TRY TO BAR IT DOWN, PART OF IT CAME DOWN, DECIDED TO PUT BOLT IN IT, MOVED BOLTER UP, ROCK CAME DOWN STRIKING HIM ON THE RIGHT SIDE OF BODY.

EMPLOYEE WAS GRINDING ON A BEAVER BOLTER STEEL. HE HAD THE STEEL CLAMPED IN A VISE AND WHILE GRINDING, GRINDER HIT VICE AND JUMPED BACK. EMPLOYEE LOST CONTROL OF GRINDER AND IT GAVE HIM TWO ABRASIONS OR CUTS ON HIS LEFT FOREARM BICEP AREA.

EE WAS CLEANING #3 DRYER SCREW WHEN THE HANDLE ON THE LEVER OF THE DUCKON BROKE CAUSING THE GATE TO SLAM SHUT. THIS CAUSED STEAM TO EXIT THE DOOR WHERE EE WAS STANDING, CAUSING 2ND DEGREE BURN S ON THE NOSE & FACE.

EE WAS INSTALLING A WHEEL STUD ON A JOY SHUTTLE CAR. AS HE HELD THE STUD WITH HIS LT. INDEX FINGER, HE TURNED THE OUTER NUT WITH AN IMPACE WRENCH. HIS FINGER WAS PINCHED BETWEEN THE STUD AND A WELD.

EE WAS BOLTING IN THE #2 ENTRY IN A94 WHEN A PIECE OF SHALED FLAKED OFF FROM ROOF AND STRUCK HIS RIGHT BICEP.

EE WAS PULLING ON A STUCK DRILL STEEL. HE STEPPED UP ON THE BOOM TO GRAB THE DRILL STEEL, WHEN THE BOOM SWUNG OVER PINCHING HIS HAND BETWEEN THE BOOM & THE DRILL STEEL.

EE WAS WELDING ON A ROOF BOLTER IN THE SURFACE SHOP. HOLDING A PIECE OF METAL 2"X4"X24" WHILE WELDING TOOK HAND OFF THE PIECE OF METAL. METAL FELL SMASHING FINGER ON RIGHT HAND.

EMPLOYEE WAS WELDING ON HEAD OF LCM IN PANEL 028-3 WHEN CREW WAS PULLINGM STACK MINER CABLE BACK. CABLE WAS WIRED UP WHILE PULLING CABLE WIRES BROKE AND CABLE FELL DOWN STRIKING HIM IN BACK.

EMPLOYEE WAS OPERATING A CONTINUOUS MINER IN PANEL L17N BY REMOTE, HE WAS STANDING ON RIGHT RIB.A PIECE OF ROCK (SHALE) FELL BETWEEN BOLTS STRIKING HIM ON HARD HAT.

EE WAS RUNNING LCM-1 IN PANEL A92 WHEN A RIB SLAB CAME OFF, PUSHING EE INTO MINER CAUSING INJURYTO HEAD & RIGHT FOOT.

EMPLOYEE WAS INSTALLING A ROOF BOLT IN THE HOLE. WHEN HE PUT THE ROOF BOLT UNDER THE GLUE AND INTO THE WRENCH, THE ROOF BOLT PLATE STRUCK HIM ON THE RT FOREARM CAUSING LACERATION.

TWO EMPLOYEES WERE BRINGING ON A CONDENSATE PUMPTHEY OPENED THE SUCTION VALVE AND DID NOT SHUT THE DRAIN VALVE. THE HOT CONDENSATE WENT INSIDE OF INJURED'S BOOT CAUSING 2ND DEGREE BURN.

EMPLOYEE WAS RUNNING CONTINUOUS MINER IN PANEL 3303. A RIB POPPED OUT AND A PIECE OF FLYING ROCK STRUCK HIM ON CHIN AND MOUTH AREA.

EMPLOYEE WAS BOLTING IN PANEL SB08 IN RM 3 LEFT, HE HAD JUST FINISHED A ROW OF BOLTS AND WAS POSITIONING THE BOLTER FOR THE FIRST BOLT OF THE NEXT ROW WHEN A SLAB FELL OUT OF THE BACK AND STRU CK HIM ON THE RT FOREARM LEFT SHOULDER AND HE SAID HIS LOWER BACK WAS SORE.

EE WAS RUNNING CONT. MINER IN PANEL SB08 ON A CLEANUP PASS. A SLAB FELL OUT FORM BETWEEN THE BOLTS & STRUCK ON THE HEAD, LEFT SHOULDER AND HAND.

EE WAS HELPING MOVE CONTINUOUS MINER USING A STEP DOWN TRANSFORMER, TRACTOR GENERATOR. EE WALKEDOR STEPPED BETWEEN GENERATOR AND TRANSFORMER. GENERATOR ROLLED FORWARD PINNING EE.

EE HAD PLACED A PIECE OF ANGLE IRON IN A POWER BAND SAW. HE HAD IT AT A 45 DEGREE ANGLE IN THE VIC E WHICH IS AN AUTOMATIC VICE. WHEN HE PUSHED THE BUTTON TO CLOSE THE VICE, THE METAL SWING AR OUND AND PINCH HIS FINGER BETWEEN THE ANGLE IRON AND THE FENCE WHICH REQUIRED SUTURES.

EE WAS UNPLUGGING THE #4 DRYER DISCHARGE CHUTE IN THE GR I & II PLANT. HE WAS USING A CONDENSATE HOSE WITH A PIG TAIL. WHEN THE CONDENSATE MIXED WITH THE HOT SODA ASH IT CAUSED IT TO (BOIL FLA SH) STRIKING EE ON THE BRIDGE OF THE NOSE.

EMPLOYEE WAS PANNING 3RXC IN PANEL M08. HE WAS LINING UP TO MATCH THE LEFT PAN TO THE RIGHT PANBEFORE DRILLING HOLE. THE LEFT PAN GOT OUT OF LINE SO HE LOWERED THE BOOM OF MACHINE TO REALIGN; PAN FELL STRIKING HIM ON RIGHT FOREARM.

EE WAS USING A 3/4" AIR IMPACT WRENCH TO TIGHTEN BOLTS ON A 6" PIPE JOINT WHEN THE AIR INLET SECTION OF THE IMPACT FAILED ALLOWING HOSE TO BREAK FREE FROM TOOL. HOSE STRUCK EE, BREAKING HIS L EYE TOOTH.

EE WAS BOLTING ROOF FALL IN PANEL SBM, REACHING UP TO INSTALL BOLT INTO HOLE, FELT PAIN IN RIGHT SHOULDER.

EE WAS BOLTING IN PANEL I80 6 ROOM RT., CUT. HE HAD TRIED TO BAR A SLATE OUT OF THE BACK & COULD NOT GET IT TO BAR DOWN. HE STARTED TO INSTALL A SPAN, TO BOLT SLAB UP. THE SLAB BROKE LOOSE, HI T HIM, KNOCKING HIM DOWN & BACK FROM MACHINE, THE SLAB HIT GROUND & BOUNCED ONTO HIS RT. ANKLE.

EE WAS RUNNING MINER IN PANEL 5BM, 1 ROOM, ROOF FELL TO SEAM. EE WAS STANDING AT LAST ROW OF BOLTS. WHEN ROOF FELL TO SEAM, A PIECE OF ROCK FELL OUT BETWEEN BOLTS STRIKING EE ON HEAD AND DOWN LEFT SIDE OF BODY.

EMPLOYEE WAS GETTING READY TO INSTALL A 3' BOLT IN ROOFING PANEL NO. 7. SLAB FELL DOWN STRIKING HIM ON RIGHT FOREARM. CAUSING A LACERATION TO ARM.

EE WAS TRYING TO GET STUCK STEEL FROM HOLE BY "CHATTERING" THE JUMBO. REACHED TO PUT MACHINE IN REVERSE AND CENTER STABILIZER BAR DROPPED, CREATING A CRUSHING INJURY TO RT. HAND WITH 1/2" LACE RATION IN PALM OF HAND.

EE WAS PULLING DRILL STEEL OUT OF THE HOLE HE HAD DRILLED AND SOME WATER THAT WAS STILL RUNNING OUT OF HOLE DRIPPED INTO HIS EYE BEHIND THE SAFETY GLASSES.

EMPLOYEE WAS RUNNING JOY MINER IN PANEL M08. HE HEARD RIB POP AND SAW RIB FALLING TOWARD HIM HE STARTED BACKING UP TO GET AWAY FROM SLAB. SLAB KNOCKED HIM DOWN AGAINST MINER.

EE WAS WALKING ALONGSIDE BOLTER WATCHING BOLTER CABLE. CABLE GOT CAUGHT ON FLOOR ANCHOR BEHIND HIM. CABLRE PULLED TIGHT & KNOCKED EE OFF HIS FEET. EE HAD A PAIR OF CHANNELLOCK WITH THE ENDS SH ARPENED ON THEN IN HIS LAMP PUNCH. CHANNELLOCKS PUNCTURED EE IN HIS RIGHT SIDE.

EMPLOYEE ALLEGES THAT HE HURT HIS LEFT SHOULDER WHILE ROOF BOLTING IN PANEL A9N. HE DID NOT TELL HIS SUPERVISOR ABOUT IT. HE WENT TOT HE HOSPITAL ON 1-24-99 FOR TREATMENT ON LEFT SHOULDER. THIS WAS UNDER INVESTIGATION UNTIL NOW.

EMPLOYEE WAS BOLTING 1/2 PASS IN L07.DRILLING A HOLE AND A PIECE OF ROCK FELL FROM THE FULL PASS SIDE THAT WAS BOLTED AND STRUCK HIM ON HE RIGHT SHOULDER AND NECK.

EE AND ANOTHER EE WERE USING A JOY ROOF BOLTER TO INSTALL A CONVEYOR DRIVE UNTI ON JOY MINER. EE GOT HIS THUMB CAUGHT BETWEEN THE BOLTER BOOM AND THE TAIL OF THE MINER, WHILE TRYING TO CONNECT THE CONVEYOR CHAIN.

EE WAS USING THE HIGH VAC HOSE. WHEN HE STRAIGHTENED OUT, HE FELT A BACK STRAIN. HE WORKED UNTIL 8-3-98 WHEN HE STARTED MISSING TIME.

EE WAS HELPING BOLTER OPERATION IN PANEL M07. HE WAS MAKING UP BOLT AND HANDING THEM TO OPERATOR AS HE WAS WALKING TO GIVE OPERATOR A BOLT, HIS FOOT SLIPPED AND HAS OPERATED WAS TRAMMING THE M ACHINE FORWARD HIS FOOT SLIPPED UNDER TIRE OF MACHINE SMASHING FOOT.

EE HAD BEEN BOLTING HIS WAY INTO THE ROOM. THE ROOM WAS CUT APPROX 1 FT ABOVE SEAM ON LEFT SIDE& ABOUT 18IN ON THE RT SIDE. HE HAD PUT IN EXTRABOLTS IN ARCH AS HE PROGRESSED INTO THE ROOM. AS HE STARTED TO DRILL A HOLE FOR THE NEXT BOLT, THE ROOF SLAB CAME LOOSE AND FELL.

EE WAS GRINDING A WELD ON AN ACID TANK AND GOT A FOREIGN OBJECT IN HIS EYES. HE HAD SAFETY GLASSES AND A FACE SHIELD ON. DOES NOT KNOW WHEN THIS OCCURRED. HE WENT TO THE HOSPITAL AND THE OBJEC T WAS REMOVED.

EMP WAS GRINDING WHEN DUST PARTICLES FLEW IN LEFT EYE. GENTAMYCIN OPTHALMIC OINTMENT ADMINISTERED.

EE & COWORKER WERE PULLING A LARGE PLATE OF STEEL OVER A TWO FOOT CEMENT LEDGE. EE WAS ON THE BOTTOM & AS THE PLATE WAS PULLED OVER THE EDGE IT BECAME UNHOOKED & SLIPPED BACK OFF THE EDGE. EE' S FOOT WAS UNDER THE PLATE WHEN IT ROCKED BACK OFF THE LEDGE.

LEANING OVER PIPE GRINDING IN UNCOMFORTABLE POSITION AND STRESSED HIS LOWER BACK.

EE WAS INSTALLING ROOF BOLTS & PANS WHEN A PORTION OF ROOF FELL STRIKING HIM ON THE LEFT FORARM AND SHOULDER.