Buscar en el registro

Employee was welding at the Plant #1 Gyro and while doing so a piece of "slag" burned through EE's pants and went into EE's left boot and burned the bottom of EE's left foot.

Employee was assisting with supplies in the area where two welders were welding. Employee stated they did not look directly at the welding light but due to being in area while welding was taking place, the reflection of the welding light caused their eyes to be subjected to arc flash.

Night crew was rebuilding 5.5' Standard Crusher, which required the use of a 60- Ton crane, which was an outside contractor. After completion of the rebuild, the employee was assisting the crane operator with stowing away the outrigger foot pads. The employee placed their right hand on top of outrigger and crane operator extracted outrigger, thus crushing the employee's right hand.

Employee was holding bolt head to enable tightening of lock nut. When the impact wrench was activated to tighten the nut, it caused the bolt to spin and crush employee's right middle finger between bolt head and crusher housing.

Temp worker was un-bridging rock from C4X front feeder. After they un-bridged the feeder and was standing to the side and observing the feeder, a rock rolled off the conveyor belt and hit temp worker in left leg. The temp did not seek medical attention and finished shift. The next morning 11/8/2022, temp went to dr. and returned to work on light duty.

EE was cutting a tac weld with grinder that had a cutting wheel. The grinder kicked back and cut EE's finger. EE was wearing gloves

He is a welder helper after he had gotten off work at 2:30 a.m. he went home and then around 5:00 a.m. his eyes started hurting. He had gotten a flash burn. He received a prescription for his eyes

He was grinding inside the main frame liners in the simmon crusher when a piece of metal got in his right eye. He was wearing all of his PPE, safety glasses, and face shield. He also washed his eye out several times thinking that he had gotten. On Friday March 1st is when he when to the doctor.

Was backing the take up off with 3/4" impact wrench when the bolt broke causing the impact to smash his fingers against a piece of metal on the frame.

Was cutting metal when a fireball fell on his blue jeans over his left knee causing a burn on his knee. Didn't go to the doctor till 7/30/08.

Employee was using an air operated impact wrench and the socket flew off and struck employee on a tooth and broke the crown.

While watching hub hammer remove concaves from gyro crusher, was struck with flying debris. Had laceration to the chin.

Welding in the gyro and the flash from another welder flash burned his eyes.

Changing wear plates on loader. When taking out the bolts with an impact wrench the bolt spun, cutting his middle finger on right hand.

HE WAS USING A CUTTING TORCH WHEN HOT SLAG WENT INTO HIS RIGHT EYE.

HELPING TO WELD A PATCH PLATE WHEN HE RECEIVED A FLASH BURN TO EYES.

WELDING ON SPRAY BAR PIPE WHEN A PIECE OF RUST POPPED AND FLEW INTO EYE.

USING DISC GRINDER ON PIECE OF METAL. PARTICLES FLEW BEHIND SAFETY GLASSES.

EMPLOYEE WAS CHANGING DRILL STEEL ON DM45E DRILLWHEN THE WRENCH HIT HIS LEFT KNEE.

WORKING ON BACKSTOP TO GEARBOX. REMAINED IN SQUATTED POSITION FOR 10-15 MINUTES.

TRYING TO CLEAN WATER LINE ON BEETLE DRILL USING AN AIR LINE. END FLEW OFF LINE & HIT EE IN LEFT JAW.

EMP WAS WELDING WHEN HOT SLAG FELL INSIDE WELDING GLOVE AND BURNED LEFT WRIST. BURN BECAME INFECTED. EMP NOTIFIED SUPERVISOR ON 5-5-97.

EE WAS WELDING ON A PIPE WHEN HE GOT SLAG IN HIS LEFT EAR.

CHIPPING SLAG FROM WELD. METAL FLEW BEHIND SAFETY GLASSES INTO RIGHT EYE.

CUTTING METAL WITH TORCH, HOT PIECE OF METAL WENT INTO BOOT.

SHOP WHERE ANOTHER EE WAS USING A GRINDER A SLIVER OF METAL FROM GRINDER HIT EE IN EYE.

CUTTING BOLT HEAD NUT OFF WHEN FOREIGN OBJECT BLEW IN EYE.

REPAIRING A WEAR PLATE IN A CHUTE, CUT PLATE OFF AND IT SLIPPED OUT OF WELDER HELPER'S HAND AND HIT EMPLOYEE'S CHEEK.

USING A CUTTING TORCH TO CUT ANGLE FROM PIPE SUPPORT OF A 8" WATER PIPE. THE PIPE FELL AND SMASHED HIS FINGER BETWEEN THE BOTTOM OF PIPE AND A LARGE CROSSTIE.

USING A PORT ABLE GRINDER WHEN A PIECE OF METAL FLEW BEHIND SAFETY GLASSES & INTO HIS EYE

TIGHTENING FEED BOLT PLATE WITH AIR WRENCH USING A WELDING ROD AS KEEPER KEEPER FLEW OUT AND HIT LEG.

USING A PORTABLE HAND GRINDER WHEN A PIECE OF FRAGMENT BLEW INTO HIS RIGHT EYE.

DISCONNECTING AIR LINE FROM COMPRESSOR WHILE BLEW DUST IN EYE.

HOLDING UP CONCAVE BLOCK TO GYRO CRUSHER WHILE UNHOOKING THEM. WHILE UNHOOKING FROM CRANE HOOK ANOTHER BLOCK HIT SIDE OF CONCAVE AND CAUGHT FINGER BETWEEN CONCAVES.

EMPLOYEE WAS USING A CUTTING TORCH TO CUT METAL WHEN RUST POPPED BACK INTO HIS EYES.

GRINDING PC OF METAL GRINDER KICKED BACK

EMPLOYEE WAS CHANGING DRILL BIT THE BIT BECAME LODGED AS HE MOVED BIT AROUND TO LOOSEN IT HIS FINGER WAS CAUGHT BETWEEN THE BIT AND THE DRILL STEEL CAROUSEL.

EMPLOYEE WAS WALKING THROUGH AREA WHERE QUARRY DRILL BITS WERE BEING SHARPENED WITH AIR GRINDER

EMPLOYEE WAS CLEANING DIRT FROM TOP OF CUTTING TIP OF ARC WELDER WHILE WEARING A WELDER GLOVES &BURNED HIS FINGER

EMPLOYEE WAS PUTTING STEEL UNLATCH BAR ON LEROY DRILL AND BIT PINCHED HIS LEFT THUMB AS HE WAS GRINDING IT THROUGH.

HELPING INSTALL AN 8 X 16 SCREEN. WELDER WELDING ON SPRAY BANG.

FLASH BURN TO EYES FROM WELDING.

LIFTING CRUSHER CHUTE WITH CHAIN ATTACHED TO CRANE. CHAIN SLIPPED AND PINCHED RIGHT HAND BETWEEN THUMB AND FOREFINGER.

EMPLOYEE WAS BE3NG LOADED BY A BACKHOE IN THE STRIPPING AREA OF THE QUARRY. A HEADACHE BALL WAS BREAKING ROCK ON THE NEXT LEVEL IN THE QUARRY. A ROCK FLEW THROUGH THE AIR AND STRUCK THE EMPLOY EE IN THE CHEEK1