Granite Mountain Quarry #1: 1 muerte registrada Metal/Non-Metal

Employee was trying to free up a seized release pin on the skid steer mast so the bucket could be removed. The release pin broke free resulting in the skid steer bucket falling and striking top of employee's foot directly behind safety toe of work boot.

Employee was dragging roller bearing out of travel way when inner bearing and race turned and pinched left hand middle and ring finger. Employee received two stitches.

Positioning Jaw Crusher in, it sprang back and penned arm against a beam and fractured wrist.

Employee was shoveling material off the C-4 pad and caught a snag on the surface of the pad with the shovel while scooping. Thus, causing EE to twist a little and strain lower back.

Night crew was rebuilding 5.5' Standard Crusher, which required the use of a 60- Ton crane, which was an outside contractor. After completion of the rebuild, the employee was assisting the crane operator with stowing away the outrigger foot pads. The employee placed their right hand on top of outrigger and crane operator extracted outrigger, thus crushing the employee's right hand.

Employee was trying to thaw out the tail pulley at the wash tower of C207. Employee poured brake-line antifreeze on the belt at the tail pulley of C207 and lit it on fire. Employee then poured more brake-line antifreeze on the fire which caused it to blow up catching EE on fire and burning EE's lower legs.

Prior to tool use, employee was changing defective fitting on a railcar jack stand after pre-shift inspection. Metal sliver cut employees thumb requiring stitches by medical prof. Jack stands owned by contractor. Injury did not involve mine equipment or system. Tool training & inspection covered in Part 46, why fitting was being changed prior to use. All PPE worn.

Employee was walking past parked skid steer with pole attachment. As EE went to step over pole, EE rolled their right ankle.

Employee was hammering a wedge in on a screen, with a hammer and strained left shoulder.

IE and a co-worker were carry a piece of metal. When the co-worker tripped causing the co-worker to slam the piece of metal into the wall. This caused IE's finger to get smashed and have 3 stitches.

EE was setting down a bucket with metal in and turned the wrong way and sprained back

EE was carrying a motor and when EE went to set it down it slipped. It caused the shaft to hit right behind the steel toe.

EE was pulling screens on S5 shaker. EE slipped hitting their right shin on the shaker strap. EE had to have stitches.

Was helping to pick up ne plates from the gradall straight across to the metal belt. When employee was putting them on the belt it slipped out of hand and fell on their other hand cutting the palm of their hand right under the fingers.

Was changing a return roller when EE reached for the roller EE's leg turned while EE's foot stayed put causing EE's knee to pop

EE was pulling on a rubber screen.

EE was helping the welder with a job and stepped off of C-2 conveyer frame and stepped on a rock and sprain right ankle.

Employee was straightening up a clamp bar on a conveyor belt, using a hammer to line it up and hit thumb.

EE was working on a screw that was stuck. EE was turning it backward to get it unstuck and that's when the v-belt smashed left index finger

EE was holding metal piece while tightening bolt with other hand. When the bolt was tight ee moved left out of the way and finger was cut on a burr from the metal ee was holding. Left index finger

Load of angle iron was being dropped in a new location when the load slipped and fell. One piece of angle iron bounced and hit EE in the lower leg. EE had a laceration with stitches.

EE was shoveling out a feeder when EE smashed EE's finger between the shovel handle and the frame of the conveyor.

Threw a piece of rip over car and it landed on my left index finger instead of falling off the side of rail car. Cleaning out rail cars

EE was working on a track hoe bucket and was hitting the bucket with a 4lb hammer when a piece of the hammer broke off going into left upper thigh.

EE was using a pry bar when it slipped and hit ee above right ear. EE was wearing hard hat.

Operator got dozer stuck and walked down a slope to see how to get the machine unstuck. Stepped on a rock and turned ankle. Resulted in an ankle sprain.

Employee was getting out of the service truck when he rolled his left ankle. This caused him to sprain his ankle.

Was working on the SB2 with a loader when some of the SB2 fell and landed on the loader bucket causing the loader to bounce. Employees head hit the dome light and cut the top of his head.

Trespasser on mine site. Police suspect blunt force trauma.

He is a welder helper after he had gotten off work at 2:30 a.m. he went home and then around 5:00 a.m. his eyes started hurting. He had gotten a flash burn. He received a prescription for his eyes

Was changing v-belts when pipe wrench slipped causing his hand to go around the shive cutting his right hand little finger

Climbing down ladder when his hand slid across metal bur cutting his finger.

He was on the welding truck to turn the welder off when he stepped off his knee gave away. EE didn't want any medical at that time he felt it would be ok. He continue to work but didn't feel it was getting any better when he came in on 8/13/12. So he didn't see a doctor till 8/13/12

EE was holding the pin while another ee was using the hammer to drive the pin into the chain when a ee missed hitting ee finger.

He was getting a piece of metal out of a chute and the metal flipped cutting his right ring finger.

Was using a 16lb hammer to strike the loader bucket to remove the shank, when a piece of metal came off, hitting him in the lower left leg. He was treated with just first aid, they said to just leave the metal in. Then the doctor decided to remove the metal on 4/29/11 and he was released to full duty.

When he first went to the clinic they did first aid and said to leave the metal in that it would be ok. Now he has an infection and the metal has moved into a muscle, so now they will be doing surgery on 9/22/10. What had happen was he was removing a belt clam with a hammer and the chisel made for belt clams when a piece of metal went into his leg.

EE was drilling with the beetle drill. He moved the pipe wrench from the holding position around to break the steel from the power head smashing his finger between the wrench and the tracks on the drill.

EE was being loaded with material when the bucket of the loader came down and hit the bed of the haul truck. EE was jarred when the bucket hit.

EE was exiting the locomotive when his foot got hung on the bottom step and he fell on his hands and knees.

Unbridging the feeder when he sprained the muscle in his abdomen. He didn't report until 11/09/2009.

Employee was using wrench to remove hose and it slipped off of nut and left hand hit bottom of engine block. Laceration to 2nd knuckle of hand.

Metal sheave counterwight came loose from a come-a-long and fell across his lower leg and foot.

Trying to put a rail bolt into a shaker when he slipped on some ice and his foot went between the floor and shaker.

Installing cylinder pin in 769 water truck, while pinning cylinder in truck he over-strained his muscles in confined space.

Was cutting metal when a fireball fell on his blue jeans over his left knee causing a burn on his knee. Didn't go to the doctor till 7/30/08.

Had patch holes in a rail car and was climbing out when he slipped and fell hurting his back. It was his three day.

He was replacing cutting edges on a loader and strained his groin while picking up a cutting edge.

Working on loader bent down to connect lines on the engine when he put his knee on a bolt that was sticking out from the frame.

Was inside shaker changing screens and replacing bed rubber, when he was cutting a piece to install and cut his thumb.

Employee was beating on a piece of metal to close off chute when he hit a rock that came up and glanced his left eye.

Employee was using an air operated impact wrench and the socket flew off and struck employee on a tooth and broke the crown.

Knelt down to tie wires on the blasting caps for a shot.

Shoveling spills of rock from conveyor belts and shakers, he strained his shoulder. He didn't go to the doctor until 3/20/07.

While watching hub hammer remove concaves from gyro crusher, was struck with flying debris. Had laceration to the chin.

Shoveling out the gyro when something hit him from behind and knocked him down. It was a large rock spraining his right ankle.

checking screens on a shaker when he grabbed the top of shaker wall and cut his hand

Turned the wrong way while moving a lifting cable out of the way. Didn't go to the dr. till 10/04/06.

Shoveling rock that had fallen from a belt, hurt his right wrist. Didn't go to the doctor till 9/13/06.

lifting screen when slipped out of his hand cutting the top of his hand

Pulling the counter weight off the right hand shaker and the counter weight fell on his right hand

unplugging chute that had a piece of metal in it when the metal cut his right index finger.

was pulling on fuel hose of a 992 loader when felt pain in his arm and elbow. Thought it would get better so waited to go to the doctor. It continue to hurt so when to the doctor on 3-7-06

Welding in the gyro and the flash from another welder flash burned his eyes.

Finished on bridging feeder; when he was coming down the hand rail broke causing him to fall, landing on both hands.

Stepping off conveyor twisted right ankle.

Was unbridging the bottom of the Jaw and a rock fell and hit the bar mashing his finger against the wall.

Changing wear plates on loader. When taking out the bolts with an impact wrench the bolt spun, cutting his middle finger on right hand.

Cutting shrink wrap off motor with pocket knife and cut hand.

Changing tire on water truck using a breaker bar to tighten lug nuts was pulling up when had a pain in lower back. He didn't report to worker comp. till 8/8/05. They felt that is wasn't compesable and went to court. Just settled that it was worker comp. Missed 33 day and still on restricted.

CHANGING GEAR BOX ON #8 BALLAST SCREWS MOTOR SLIPPED AND SMASHED FINGER BETWEEN MOTOR AND A BOLT

Cutting metal on bucket metal popped off cutting left hand little finger.

While getting off plate feeder his foot got caught between plate feeder and side board.

EE WAS HELPING TO THROW SCREENS OFF THE TOWER WHEN HE PULLED HIS BACK.

EE WAS WALKING ACROSS THE FLOOR UNDER THE GYRO WHEN HE TURNED HIS ANKLE.

Slip in bucket while trying to hold a piece of metal. didn't go to the dr til 4-19-04.

PULLING HOSES ON FUEL TRUCK RIGHT HAND GOES NUMB.

CLEARING A FEEDER WHEN ROCK HIT HAND.

WHILE INSTALLING BUSHING IN SHOVEL BUCKET HAMMERBROKE OFF AND STRUCK EE IN THE HEAD.

HE WAS USING A CUTTING TORCH WHEN HOT SLAG WENT INTO HIS RIGHT EYE.

CHANGING ROLLERS ON A CONVEYOR WAS PULLING UP ON BELT WHEN HE FELT THE STRAIN.

HE WAS LOADING A SHOT WHEN PUTTING TUBE IN HOLE THE ROCK HOLDING THE CAP WIRES FLIP UP HITTING HIS LEFT FOOT.

EMPLOYEE FELL WHILE CHECKING SCREENS ON A VIBRATORY SHAKER. EE FELL OFF ANOTHER VIBRATORY SHAKER EARLIER INT HE EVENING, BUT IT WAS NOT REORTED UNTIL AFTER THE SECOND FALL.

HELPING TO WELD A PATCH PLATE WHEN HE RECEIVED A FLASH BURN TO EYES.

WHILE HELPING TO LEAD A SUMP PUMP IN THE BACK OF A PICKUP, EE HURT LOWER BACK.

DOING CLEANUP WITH WATERHOSE AND TWISTED.

ABOUT 3 WEEKS PRIOR TO RECEIVING MEDICAL ATTENTION EE COMPLAINED OF A WRIST PROBLEM AFTER LIFTING A SCREEN. WHILE SHOVELING ON 9/12/02 HE SAID HIS FINGERS WENT NUMB AND WAS GIVEN MEDICAL ATTEN TION.

USING A 16 POUND SLEDGE HAMMER TIGHTENING BOLTS TO SLIPPED ON GYRO CRUSHER.

CHANGING A SCREEN ON THE 6 X 16 SHAKER AND CAUGHT FINGER BETWEEN THE RAIL AND THE SCREEN.

CLOSING A DOOR TO A FEEDER, THE HANDLE SLIPPED & STRUCK HIS RIGHT UPPER ARM.

WORKING AROUND BASE PLANT WHEN ROCK BOUNCED AND HIT HIM IN THE EYE.

WALKING ALONG CONVEYOR WALKWAY AND BUMPED HEAD ON OVERHEAD BEAM.

USING A SHOVEL TO CLEAN OUT RAIL CARS.

HAUL TRK WAS BEING LOADED WHEN A LARGE BOULDER JARRED THE TRK & CAUSED BACK PAIN TO EE

EE WAS OPERATING A WATER TRUCK AND HIT POTHOLE IN ROAD AND JARRED HIS BACK.

LIFTING METAL AND SCREEN AND BACK BECAME SORE.

FUELING TRUCK AND HUNG ON TANK WHILE FUELING INSTEAD OF USING A STEEP EXAMINER.

ROCK FELL OFF PLATFORM AND HIT HAND.

PULLING ON 18" CRESCENT WRENCH WHILE WORKING ON GYRO CRUSHER.

WELDING ON SPRAY BAR PIPE WHEN A PIECE OF RUST POPPED AND FLEW INTO EYE.

CLOSING ELEVATOR DOOR ON SECONDARY TOWER AND CAUGHT FINGER BETWEEN DOOR.

USING HIGH PRESSURE WATER HOSE WHILE WASHING OUT BALLAST SCREWS WHEN POWER SURGE CAUSED HIM TO FALL OVER 8" PIPE.

CLEANING WINDSHIELD ON 970F LOADER, SLIPPED AND FELL TO THE GROUND.

LIFTING DIRTY WATER PUMP BY CABLE AND CUT HAND.

LIFTING A 2 FOOT BLOCK ON 8"X8" WOOD AND BUMPED IT AGAINST UNDERSIDE OF 1 TON TRUCK BED.

PULLING SCREEN OUT OF VIBRATOR WHEN HOOK SLIPPED AND EE FELL BACK AGAINST SPRAY NOZZLE.

INSTALLING A NEW BLADE ON HOSE CUTTER HIS HAND SLIPPED ON CUTTER BLADE.

EMPLOYEE WAS CHANGING DRILL STEEL ON DM45E DRILLWHEN THE WRENCH HIT HIS LEFT KNEE.

CHANGING THE DISCHARGE VALVE ON THE PLANT CLARFER WHEN STRAINED SHOULDER LOOSENING BOLT

TAKING METAL OFF OF C-4 CONVEYOR BELT. CUT SMALL FINGER.

SHOVELING MATERIAL ON 5TH FLOOR OF SCREENING TOWER WHEN SHOVEL CAUGHT ON METAL DEBRING RESULTING IN STRAIN TO LOWER BACK.

SHOVELING MATERIAL OUT OF RAIL CARS TO BE REPAIRED BY WELDER

PULLING CONES OUT OF DRILL HOLES

ADJUSTING MOTOR MOUNTS ON CIDO CONVEYOR BELT WHEN WRENCH SLIPPED AND HIT RIGHT EYE.

CHANGING SCREENS IN WASH PLANT. PULLING ON SCREEN AND STRAINED SHOULDER.

CARRYING METAL UP STAIRS AND BECAME TOO HOT.

CHANGING SCREENS TO 7TH FLOOR SHAKER PULLING SCREEN OUT OF SHAKER.

CLIMBING UP STAIRS IN ORDER TO CLEAN OUT SB2 BIN AND BUMPED LEFT KNEE ON LADDER.

REMOVING RADIATOR CAP FROM OVERHEATED WA 450-2 KOMATSU LOADER.

TRIPPED GOING DOWN STAIRS TO GYRO WHILE GETTING OUT OF STONIM.

THUNDERSTORM APPROACHING, EE RAN FOR COVER, TRIPPED ON GYRO STAIRS.

THE EMPLOYEE WAS CUTTING RAIL TIES AND DEVELOPED AN ALLERGIC REACTION TO CREOSOTE.

EMPLOYEE WAS HELPING TO CHANGE SCREENS WHEN HE HIT HIMSELF WITH A SHOP HAMMER.

EE WAS MIXING PACKING MATERIAL FOR CRUSHER OVERHAUL.

EE WAS MIXING PACKING MATERIAL FOR CRUSHER OVERHAUL.

LIFTING AND REPLACING SCREENS AT PRIMARY TOWER.

SHOVELING DURING CLEANUP & TURNED TO DUMP SHOVEL & FELT SHARP PAIN IN SHOULDER & BACK.

REPLACING SCREENS AT WASH PLANT AND PICKED UP A SCREEN AND STRAINED BACK.

EE WAS TIGHTENING ABOLT ON AN AIR COMPRESSOR WHEN THE WRENCH SLIPPED OFF THE BOLT & HIS LEFT HAND STRUCK A SHARP PIECE O METAL.

PULLING ON A CONVEYOR ROLLER PULLEY WHILE TYRINGTO INSTALL IT.

EE WAS RIDING ON A PLANT SCREEN ON TRUCK BED WHEN SCREEN SHIFTED & BACK HIT EDGE OF BED. [REPORTED TO SUPER ON 9-10-97]

EE WAS SHOVELING ROCK AT REBLEND SCREENING PLANT WHEN HE LIFTED A SHOVEL FULL OF ROCK AND FELT PAIN IN LEFT GROIN AREA.

EMP WAS WELDING WHEN HOT SLAG FELL INSIDE WELDING GLOVE AND BURNED LEFT WRIST. BURN BECAME INFECTED. EMP NOTIFIED SUPERVISOR ON 5-5-97.

STANDING INSIDE BATHROOM WHEN WALLS CAVE IN DURING TORNADO AT PLANT.

GOING DOWN STEPS TO C1 TUNNEL AND TWISTED WHEN A TORNADO HIT THE PLANT.

STANDING OUTSIDE WELDING SHOP WHEN TORNADO HIT PLANT.

STANDING OUTSIDE WELDING BUILDING WHEN TORNADO HIT PLANT.

HE WAS GETTING A COME-A-LONG OUT OF PICK-UP TRUCK WHEN FOOT SLIPPED OFF OF BUMPER AND LEFT HAND SMALL FINGER HIT SOMETHIG IN BED OF TRUCK.

UNBRIDGING A CHUTE WHEN EE CAUGHT HIS HAND BETWEEN SHAKER & WALL

EMPLOYEE WAS CLIMBING ON VIBRATOR SCREEN TO HOOKUP A CRANE TO A PIECE OF METAL WHEN METAL SLIPPED STRIKING RIGHT FOOT.

EE STATES HE WAS BUMPED BY PICKUP TRUCK WHILE USING TELEPHONE AT PLANT OFFICE.

EE WAS CLIMBING DOWN FROM A 16 X 20 SCREEN ASSEMBLY BEING ASSEMBLED, WHEN HE STEPPED ON THE GROUND HE TURNED HIS LEFT KNEE.

EE WAS WELDING ON A PIPE WHEN HE GOT SLAG IN HIS LEFT EAR.

CHIPPING SLAG FROM WELD. METAL FLEW BEHIND SAFETY GLASSES INTO RIGHT EYE.

STEPPING ACROSS A DITCH WHEN HE STEPPED ON A ROCK AND TWISTED HIS ANKLE.

SHOP WHERE ANOTHER EE WAS USING A GRINDER A SLIVER OF METAL FROM GRINDER HIT EE IN EYE.

EMPLOYEE WAS WORKING WITH ANOTEHR EMPLOYEE TAKING THE DRILL HAMMER HEAD APART WHEN HE CAUGHT HIS RIGHT SMALL FINGER IN A CHAIN WRENCH.

EMPLOYEE WAS CLIMBING OUT OF FEEDER AND TWISTED RIGHT KNEE. RECEIVED ACCIDENT REPORT IN CORPORATE OFFICE ON 9-26-95.

EE WAS CROSSING RAILROAD ENGINE WHEN HE SLIPPED ON WET STEPS.

EMPLOYEE WAS CLEANING DECKING OF THE C115 CONVEYOR WHEN HIS SCRAPER CAUGHT IN THE CONVEYOR.

A STEEL BAR FELL AND HIT EMPLOYEE ON HAND WHILE THEY WERE CLOSING THE JAW CRUSHER TO A SMALLER SIZE OF ROCK.

CHUTE WITH SHOUT PIPE WHEN FINGER WAS PINNED AGAINST SIDE BOARD.

TAKING SAMPLE SCREEN OUT OF VIBRATOR.

EMPLOYEE WAS IN A CHUTE PULLNG UP A HEAVY METLA BAR AND STRAINED HIS BACK.

WHILE SHOVELING MATERIAL IN PLANT, EMPLOYEE THINKS HE PULLED MUSCLES IN LEFT SHOULDER.

EE SLIPPED AND FELL ON THE ICE RESULTING IN A FALL DOWN THE STAIRWELL AND GETTING LEFT ARM HUNG IN HAND RAIL.

LOOSENING HOSE CLAMP, SCREWDRIVER SLIPPED AND CUT FINGER ON CLAMP.

REPAIRING A WEAR PLATE IN A CHUTE, CUT PLATE OFF AND IT SLIPPED OUT OF WELDER HELPER'S HAND AND HIT EMPLOYEE'S CHEEK.

EE WAS DISMOUNTING FROM CAT 777C TRUCK WHEN HIS HARD HAT BLEW OFF HE GRABBED FOR HAT AND TURNED LOOSE OF HAND RAIL AND FELL TO THE GROUND.

PICKING UP 10 GAL WATER CAN AND STRAINED BACK. NOTIFIED COMPANY ON 12-19-94 AFTER HAVING BACK SURGERY.

USING A CUTTING TORCH TO CUT ANGLE FROM PIPE SUPPORT OF A 8" WATER PIPE. THE PIPE FELL AND SMASHED HIS FINGER BETWEEN THE BOTTOM OF PIPE AND A LARGE CROSSTIE.

THROWING A ROCK INTO FEEDER AT C1 TUNNEL TO UN BRIDGE IT.

INSTALLING NEW MOTOR ON GYRO FEEDER. MOTOR SLIPPED STRIKING EE'S RT KNEE.

WALKING DOWN STAIRS. AT REBLEND CONTROL TOWER, HUNG RIGHT FOOT IN STAIRS.

OPERATING A FRONT END LOADER & LUNGING INTO PILE TO LOAD BUCKET WHEN HE JARRED HIS BACK

USING A PORT ABLE GRINDER WHEN A PIECE OF METAL FLEW BEHIND SAFETY GLASSES & INTO HIS EYE

CHANGING OIL IN CAT 773 TRUCK. OIL FILTER CAME LOOSE AND FELL UPSIDE DOWN ON ELMPLOYEES HAND HAT. HOT OIL WENT INTO EMPLOYEE'S EAR.

LIFTING A LARGE METAL PIN WHILE WORKING ON ELECTRIC SHOVEL.

TIGHTENING FEED BOLT PLATE WITH AIR WRENCH USING A WELDING ROD AS KEEPER KEEPER FLEW OUT AND HIT LEG.

EE WAS LIFTING A PIECE OF FLAT IRON 1/2X8X60 INTO THE OPENING IN A CHUTE ON BALLASH WASHING PLANT

EE HAD HIS HAND ON THE CONVEYOR DECKING WHEN A ROCK ROLLED OFF THE MOVING CONVEYOR STRIKING THE TIP OF HIS LEFT INDEX FINGER.

EE BENT OVER TO CHECK THE SCALE READ OUT WHEN A SHARP PAIN OCCURRED IN HIS NECK AND HE COULD NOT SIT UP.

DIGGING ROCKS FROM ROCK BOX ABOVE STANDARD CRUSHER A ROCK WEIGHTING 840 POUNDS FELL STRIKING EE S HAND.

USING A PORTABLE HAND GRINDER WHEN A PIECE OF FRAGMENT BLEW INTO HIS RIGHT EYE.

EMPLOYEE WENT TO BACK OF DROPBALL IN KILL ENGINE. AS HE WAS CLIMBING DOWN HE CAUGHT HIS RING ON RADIATOR CAP CAUSING HIM TO LOOSE HIS BALANCE AND FELL TO GROUND AND SPRAINED ANKLE.

CHANGING BOTTOM DECK SCREEN ON LEFTHAND 7TH FLOOR.

LIFTING ON ONE END OF A 12" PIPE APPROXIMATELY 6 FEET LONG.

CLIMBING LADDER TO 50 TOW HAUL TRUCK WHEN FOOT SLIPPED AND HE FELL.

EE WAS WALKING TO WINCH TRUCK HE SLIPPED ON FELL AGAINST BACK OF WINCH TRUCK STRIKING LOWER LIP.

DESCENDING LADDER FROM CAT 777B AND STEP IN HOLE WHERE TRUCK WAS PARKED.

DISCONNECTING AIR LINE FROM COMPRESSOR WHILE BLEW DUST IN EYE.

HELPING BUILD A ROCK BOX CHUTE FOR C-1 CONVEYOR HE WAS TRYING TO KICK A PIECE OF METAL IN PLACE WITH HIS FOOT.

SHOVELING C-1 TUNNEL SOME TYPE OF INSECT STUNG HIM.

HOLDING UP CONCAVE BLOCK TO GYRO CRUSHER WHILE UNHOOKING THEM. WHILE UNHOOKING FROM CRANE HOOK ANOTHER BLOCK HIT SIDE OF CONCAVE AND CAUGHT FINGER BETWEEN CONCAVES.

EMPLOYEE WAS HELPING TO LOAD SCREEN IN ELEVATOR WHEN HE FELT A POP IN HIS BACK.

EMPLOYEE WAS CLEANING DECK UNDER FRONT FEEDER IN C-1 TUNNEL. HE WAS CLEANING BETWEEN DELIVERY ROLELR UNDER FRONT FEEDER. BELT GRABBED HOE ADN ROLLED LEFT HAND BETWEEN BELT ADN DELIVERY ROLLE R.

STEPPED ON LOOSE ROCK & LOST FOOTING WILE MEASURING INSIDE OF CHUTE.

GRINDING PC OF METAL GRINDER KICKED BACK

LOOSENING BOLT ON LEROF DRILL WHEN HE STRAINED HIS RIB CAGE MUSCLES.

HELPING DIG OUT THE 71 STANDARD CRUSHER WHEN A ROCK HIT HIM ON THE SHOULDER.

PRYING GYRO BELT BACK INTO PLACE WITH PRY BAR.

KNOCKING BOLTS FROM FEEDER AT JAW WHEN HE HIT HAND WITH HAMMER.

DRIVING A WEDGE INTO A RAIL BOAT WITH AHMMER WHEN THE WE POPPED BACK OUT AND EE ON THE LOWER LIP.

INSPECTION OF TRACKS TRIPPED ON END OF TIE FELL ON BALLAST

EMPLOYEE WAS PICKING UP A PICE OF 1/2" PLATE WHEN HAND SLIPPED FROM METAL LETTING METAL FALL ON LEFT HAND.

USING A SHOVEL, CLEANING UP AROUND A TAIL PULLEY AT C4A.

EMPLOYEE WAS WELDING IN A CHUTE BELOW GYRO CRUSHER WHEN THE WIND BLEW TRASH IN HIS LEFT EYE.