Buscar en el registro

EMPLOYEE WAS HOLDING HAND ON OPPOSITE SIDE OF A DOOR DRILLING SIGN. DRILL BIT WENT THRU SIGN AND INTO LEFT HAND. WOUND REQUIRED 2 STITCHES.

Employee received flash burns to the eyes, neck, and face while working in finish mill #1 removing liners. Liners are cut into 250 lbs pieces for removal.

WHILE CLEANING, INLET EMPLOYEE WENT TO PULL AIR LANCE OUT AND FELT A SHARP PAIN ON SHOULDER BLADE AREA.

While employee was trying to turn a twisted bag of cement on the palletizer, unit cycled and pushed him to the rear wall of the layer pusher area of the unit. Employee sustained contusion to lower back, lumbago, lower extremity abrasion w/o infection, and contusion of lower leg.

While cutting grass with the weed eater in high weeded area, an insect crawled up employee's leg and bit him. Insect bite of nonvenomous type.

Employee was installing a feed chute at the #1 finish mill throat. Unit was being hoisted up by an air tugger. The cable had an overlay wrap off track when chute was being lowered, the wrap of cable let loose and weight of the feed chute shifted to employee, causing a lumbar strain.

Employee was inspecting post maintenance repair of the raw meal feed sampler. During the operational test the sampler mixer unexpectedly activited.

EE had filled a pill press with sample material. He installed the top cap but noticed it was cocked to the side. When he reached to correct it his lab coat inadvertantly caught the power handle causing the machine to activate. This spewed the sample material into his eye.

EE was preparing to cleanout a discharge chute with a hand held air hammer. When he pulled the air hammer trigger, escaping air stirred up a cloud of fine material. This fine material then entered into his eye.

EE WAS FITTING PLATES ON THE PRECIPITATOR AND SOMETHING FELL OR BLEW INTO HIS EYE.

Using a cutting torch, a welder had cut too far into an overhead metal plate without leaving an uncut portion as "safety margin" for final, assisted cut. The plate broke free and struck welder in right eyelid in a swing-type motion. Upper eyelid was torn in a "V"-shape requiring sutures.

Standing on 1 foot block jack-hammering (overhead) refactory from vessel on preheat tower, 6th floor. Bit jammed in refractory. While extracting bit it freed up unexpectantly and EE fell to the ground.

EMPLOYEE WAS LEANING OVER BEAM WITH AN IMPACT WRENCH AND TWISTED CAUSING PAIN IN HIS BACK.

EE WAS HOLDING A FRAME IN PLACE FOR INSTALLATION. A CO WORKER MISSED THE FRAME AND HIT THE EE IN THE BACK OF THE HAND. THE EE DID NOT GO TO SEE A DR UNTIL 4-11-03.

THE EE WAS BREAKING UP ROCK IN THE CRUSHER WITH A JACKHAMMER. THE JACKHAMMER SLIPPED WHEN THE ROCK BROKE AND THE HAMMER HIT THE EE IN THE TOP OFTHE FOOT.

EE STATES THAT HE JUST NOTICED AND PAIN IN HIS SHOULDER. WHILE OPERATING A BULLDOZER.

THE EE WAS BACKING UP A PALLET JACK WHEN HE CAUGHT HIS ARM BETWEEN THE JACK AND A GUARD RAIL.

EMPLOYEE WAS USING AN IMPACT WRENCH TO REMOVE SOME BUCKET BOLTS ON AN ELEVATOR CHAIN. THE IMPACT SOCKET SLIPPED OFF OF THE BOLT AND THE SWIVEL CUT HIS LEFT THUMB.

EE WAS GRINDING A DISC ON A PILL PRESS WHEN HE THOUGHT HE GOT SOME DUST IN HIS EYE. WHEN IT DID NOT GET BETTER AFTER RINSING HIS EYE HE ASKED TO SEE A DR.

EE WAS GRINDING ON A SCREEN SUPORT IN A FINISH MILL, WHEN A FOREIGN OBJECT ENTERED HIS LEFT EYE. HE WAS WEARING HIS SAFETY GLASSES AT THE TIME.

EMPLOYEE WAS USING AN ELECTRIC GRINDER TO GRIND METAL WHEN HE FELT SOMETHING GO INTO HIS RIGHT EYE. HE WAS WEARING SAFETY GLASSES AT THE TIME.

EE STATES THAT HE WAS CUTTING T-BOLTS UNDER THE CLINKER COOLER CARRIAGE, WHEN HE FELT SOME DUST FROM ABOVE GO INTO THE LEFT EYE. HE WAS SENT TO THE DR ON 3/8/97 AFTER COMPLAINIG OF IRRITATION

EE WAS IN THE KILN DRILLING REFRACTORY FOR BRICKWIDTH, WHEN A PIECE OF COATING BROKE LOOSE & STRUCK HIM ON THE LEFT SHOULDER, CAUSING A CONTUSION.

EMPLOYEE WAS ATTEMPTING TO CHANGE OUT A DAMAGED 70 AMP CIRCUIT BREAKER AT THE CRUSHER ELECTRIC ROOM WHEN AN ELECTRIC ARC FLASH OCCURRED CAUSING BURNS TO HIS FACE AND RIGHT HAND. THE ARC FLASH WAS DUE TO THE BREAKER BEING ENERGIZED AND TWO INCOMING HOT LINES CAME IN CONTACT.

EMPLOYEE STATES THAT HE WAS USING A GMAW WELDER IN RAW MILL AND LATER WOKE UP WITH IRRITATION INBOTH EYES, ALONG WITH REDNESS. WAS SENT TO DR ON1-9-96.

EMPLOYEE WAS USING A SMALL AIR HAMMER TO BREAK UP MATERIAL BUILDUP AT THE RISE LOUISE BIN, WHEN A CHUNK ACCIDENTALLY BECAME DISLODGED, STRIKING THE AIR HAMMER WHICH INADVERTENTLY STRUCK HIM CA USING A SMALL LACERATION BEHIND THE LEFT EAR.

EE WAS USING AN AIR CHIPPING HAMMER TO REMOVE BUILDUP FROM THE RAW MILL BUFFER BIN, WHEN A PIECE OF BUILDUP BROKE FREE, STRIKING THE HAMMER AND CAUSING THE HAND HOLDING THE HAMMER TO STRIKE TH E RIGHT SIDE OF HIS FACE.

INJURED WAS CLEANING OFF THE PHOTOCELL EYES UNDER THE CAR PALLETIZER, WHEN HE ACCIDENTALLY TRIPPED THE SWITCH FOR THE SQUEEZE ROLLER, PINCHING THE RIGHT INDEX FINGER CAUSING AN AVULSION.

EE STATED THAT HE WAS USING A 1 INCH AIR DRIVEN IMPACT WRENCH WHEN THE AIR SUPPLY SIDE OF THE HOSE CAME LOOSE AT THE CLAMP AND HE FELT A SHARP PAIN IN HIW LOWER BACK AS HE MOVED AWAY TO AVOID BEING STRUCK BY THE HOSE. HE WENT TO SEE DR ON 9-21-92 AFTER COMPLAINING OF BACK PAIN.

EMPLOYEE WAS WELDING INSIDE RAW MILL HOUSING WITH THE DOORS OPEN AND EXCELLENT VENTILATION, BUT STILL DEVELOPED SOME SORT OF EYE IRRITATION FROM DUST OR FUMES. HE WAS SENT TO THE DOCTOR FOR EV ALUATION AND TREATMENT ON 4-28-91 DUE TO EYES SWELLING.

INJURED WAS USING A CUTTING TORCH TO REMOVE A BIN VIBRATOR WHEN THE VIBRATOR BROKE LOOSE FROM THE BIN WALL AND LANDED ON HIS RIGHT HAND CAUSING LACERATION.

USING AIR HAMMER TO KNOCK DOWN REFR. INSIDE KILN FELT SOME DEBRIS IN L EYE SENT TO DR ON 10--689 COMPL OF PAIN DISCOMFOR IN EYE

USING CHAINSAW TO CUT SOME FALLEN TREES WHEN SAW ACCI. JUMP BACK STRUCK HIM ON THE L KNEE CAUSING LACERATION . SENT TO VILLAGE OAKS ER ROOM FOR EVAL TREATMENT ON 10-4-89.

INJURED WAS USING A HAND DRILL TO REMOVE RIVETS FROM HIS TOOL POUCH, WHEN THE DRILL BIT ACCIDENTALLY BROKE AND THE BROKEN PIECE GOING INTO HIS LEFT THUMB CAUSING A LACERATION. HE WAS SENT TO V ILLAGE OAKS HOSPITAL FOR EVALUATION AND TREATMENT ON 8-2-89.

INJURED WAS USING AN AIR HAMMER TO BREAK A LARGE ROCK IN THE CRUSHER HOPPER WHEN THE ROCK ACCIDENTALLY SHIFTED, PINCHING HIS RIGHT HAND WITH AIR HAMMER AND THE CRUSHER FRAME WALL.

INJURED WAS USING TORCH TO CUT PIECE OF METAL AT PLANT SCRAP BIN WHEN PIECE OF METAL ACCIDENTLY FELL STRIKING HIM ON INSTEP OF LET FOOT.

INJURED WAS USING ROTARY DRILL TO CUT HOLE IN ELECTRICAL CABINET WHEN BIT ACIDENTALLY CAUGHT CAUSING HANDLE TO STRIKE HIM ON LEFT HAND.

INJURED WAS MONITORING KILN DEFLECTION WHEN HIS LEFT HAND WAS ACCIDENTALLY CAUGHT BETWEEN A KILN RPM COUNTER AND THE STRIKER THAT IS MOUNTED ON THE KILN SHELL

WHILE WELDING U3DER KILN IN AN AWKWARD PSITION FOR AN EXTENDED TIME, HE DEVELOPED PAIN IN LEFT HIP AREA

INJURED WAS USI3G AN ELECTRIC IMPACT WRENCH TO TIGHTNE BOLTS FOR THE KILN COOLER UNDERGRATES,CAUSING A STRAIN IN HIS RIGHT WRIST.

WHILE USING ACE7YLENE TORCH, HOT SLAG FELL INTO LEFT SLEEVE CAUSING BURNS TO FOREARM.

INJURED WAS USI3G AN AIR LANCE TO GET CEMENT FLOWING IN CEMENT SILO WHEN HE WAS ACCIDENTALLY SPLASHED IN FACE WITH CEMENT, AND KNOCKING HIS SAFTEY GLASSES OFF.

INJURED WAS USI3G A 3/4IN IMPACT GUN TO REMOVE NUTS FROM FINISH MILL COMPARTMENT DOOR HE WAS HOLDING THE SOCKET WHEN THE ROD HOLDING THE SOCKET ATTACHED TO THE DRIVE CAME LOOSE & CUT HIM ON TH E LEFT HAND 3

INJURED WAS OPE9ATING A RIDING LAWN MOWER WHEN HE RODE SIDEWAYS INTO A SMALL DITCH.HE USED HIS RIGHT FOOT TO BALANCE MOWER WHEN IT WENT SLIGHTLY OFF BALANCE.TWISTING HIS ANKLE IN THE PROCESS.

EE WAS WELDING 4HEN ARC OF WELDER WAS THROWN ON LEFT HAND RING FINGER.

RAISING A LOAD WITH AN AIR TUGGER LOAD GOT CAUGHT ON STEEL THE INJURED MAN GRABBED ONTO THE CABLE TO SWING THE LOAD WHILE DOING SO THE LOAD WAS RAISED HIS HAND RODE UP THE CABLE INTO THE SNATC H BLOCK

I WAS LIGHTING CAD WELD WITH CIGARETT LIGHTER

EMPLOYEE WAS CU7TING OUTTERTIERY AIR DAMPER WHICH WAS HELD WITH BOLTS HE STARTED CUTTING FROM TOP & HAD ONE BOLT LEFT ON BOTTOM WHEN HE CUT THE LAST BOLT THE DAMPER FELL INJURING UPPER RT ARM & LEFT ANKLE OF3EMPLOYEE

EMPLOYEE WAS ON TOP OF MUDDY BEAM WELDING WHEN HIS FOOT SLIPPED. HE HIT HIT RIGHT KNEE ON THE EDGE OF THE BEAM.

THE INJURIED STARTED IMPACTING BOLTS IN THE FINISH MILL BLDG. A SMALL PIECE OF WIRE WAS LEFT IN THE SOCKET. THIS WIRE WAS SPINNING WITH THE SOCKET WHILE PROTRUDING OUT OF THE SOCKET. THE INJUR ED WAS HOLDING ON TO THE SOCKET WITH HIS LEFT HAND. THE WIRE TORN INTO HIS HAND FROM INDEX FINGER TO THUMB.