Buscar en el registro

EMPLOYEE WAS STANDING ON THE NORTH SIDE OF TAIL PULLEY RESTING FOOT ON THE TOE PLATE, UNDER THE TAIL PULLEY SUPPORT FRAME. BELT TRAVELING UPWARDS CAUGHT THE TOE OF THE BOOT AND PULLED HIS FOOT INTO THE STRUCTURAL IRON.

EMPLOYEE WAS TEARING OUT REFRACTORY IN THE PREHEAT TOWER WHEN A LARGE PIECE HIT HIM ON HIS LEFT FOOT CAUSING A CONTUSION.

EMPLOYEE WAS REMOVING A SEAL AIR PIPE AND GUIDING PIPE WHEN THE PIPE CAUGHT SIDE OF HIS HAND CUTTING THE PALM.

Employee was replacing Hydraulic cylinder of cross-over bridge at scale #4. Cylinder outer sleeve slipped from retaining U-bolts, pinching left forearm between forklift and sleeve as he was securing the bottom plate, causing a compound fracture of the left forearm.

EMPLOYEE STOOD UP AND TURNED FROM KNEELING POSITION ON SLOPED FLOOR OF CONVEYOR GALLERY AND EXPERIENCED A POP AND PAIN IN HIS LEFT KNEE.

EMPLOYEE ALLEGED THAT ON 04/16/2010 HE SLIPPED ON STAIRS WITH IDLER ON A DOLLY AND INJURIED THE SAME ANKLE THAT WAS INDICATED ON THE REPORT OF 12/12/2008 E-DOCUMENT # 730864. ACCIDENT WAS NOT REPORTED UNTIL 05/11/2010. POSSIBLE CONTINUATION OF ORIGINAL FRACTURE OF CALCANEUS FROM 12/12/2008.

EMPLOYEE WAS CLEANING CHALK BIN WHEN A CHUNK OF CHALK FELL AND HIT HIM ON THE LEFT SHOULDER.

EMPLOYEE WAS HOLDING HAND ON OPPOSITE SIDE OF A DOOR DRILLING SIGN. DRILL BIT WENT THRU SIGN AND INTO LEFT HAND. WOUND REQUIRED 2 STITCHES.

EE was bending over to pick up a 6" C-Channel & felt a sharp pain in his back.

Employee was hit by a 3' piece of angle iron that fell from above. Angle iron hit employee's right hand 4th finger on the nail.

EMPLOYEE SLIPPED IN RESTROOM AND SLIGHTLY TWISTED HIS LEFT KNEE.

EE laid down in his vehicle during a break and didn't wake up. He suffered a non work related heart attack.

Employee was entering finish mill #1 by descending a portable ladder. The ladder came away from the wall and employee fell back, twisting his right ankle when landing on the floor of the mill. Work activity was mill liner changing.

Employee received flash burns to the eyes, neck, and face while working in finish mill #1 removing liners. Liners are cut into 250 lbs pieces for removal.

WHILE CLEANING, INLET EMPLOYEE WENT TO PULL AIR LANCE OUT AND FELT A SHARP PAIN ON SHOULDER BLADE AREA.

EMPLOYEE WAS MOVING SPRINGS DOWN DOME 2 STEPS TO REBUILD FEEDER. STRAIN IN LOWER BACK. (DCN: 220093440024-turned to a lost time reportable case of 12/9/09)

While cleaning chute to sand bin, employee positioned himself wrong and felt his back pop.

Employee was lifting a bucket of material when he complained of a pain in the neck area. This condition is being treated by his personal doctor and has been recommended for surgery. The condition is a result of a pinched nerve in the neck area. The condition is not a result of an accident. Report is for record only.

FOR RECORD ONLY. Employee of Uvalde Concrete Company picked up a load of cement in transport truck. While on our property he said that he was having trouble breathing and did not feel good. EMS was called and the driver was taken to a hospital and admitted for heart surgery. There was no accident and the above was NOT our employee.

Cement dust from N13 dust collector bag change out got in employee's eye.

While cleaning preheater floor 2B, closing north door, door got stuck and while helping door it broke loose smashing finger with door latch.

Employee alleges that he received a carpal tunnel injury while shoveling spilled over cement material from the gallery onto the conveyor at the finish mill to cement silo conveyor on August 20, 2007. Worker's comp. has denied the claim. THIS REPORT IS FOR MEMO ONLY.

Employee was removing a conveyor splice joiner pin with vice grips and a hammer. The hammer glanced off the vice grips and struck the top half of his left index finger causing a contusion of the left hand.

Employee slipped with his right foot while standing on a pile of firm cement, rolling his ankle causing a sprain.

While employee was trying to turn a twisted bag of cement on the palletizer, unit cycled and pushed him to the rear wall of the layer pusher area of the unit. Employee sustained contusion to lower back, lumbago, lower extremity abrasion w/o infection, and contusion of lower leg.

Employee was placing 3 to 31/2 inch steel grinding balls on conveyor belt when two balls rolled together mashing left index finger between them.

Employee was walking from 2nd to 3rd floor of pre-heat tower, to next flight of stairs and hit finger on hand rail.

Employee was stepping down a ladder and His foot slipped on the last step. He did not fall, he just sprained his ankle.

Completing port hole inspection on the pre heat tower. Restriction was found right below port on south 3C. Cleared blockage and went to 4th south level to check port. Opened port & within 15 seconds, material shot out causing burns. Material blew under face shield & hard hat.

Employee alleged that after he had punched out for the shift and walking to his car, he fell down injuring his thigh. There was no eyewitness to the accident. The accident was not reported until 12/01/2006.

Cleaning tracks on D-10 dozer with a bar. The bar slipped and hit the dozer frame and then hit the mechanics right hand resulting in a closed fracture of the navicular bone of wrist.

While cutting grass with the weed eater in high weeded area, an insect crawled up employee's leg and bit him. Insect bite of nonvenomous type.

Employee was walking downstairs and stepped on a clinker ball with foot rolling to one side, resulting in a twisted ankle. Continuation of E-Document 380138. EE grabbed the hand rail to catch himself and pulled the tendions in his right arm. The condition worsened with time and required additional medical follow-up and resistricted duty.

Employee was installing a feed chute at the #1 finish mill throat. Unit was being hoisted up by an air tugger. The cable had an overlay wrap off track when chute was being lowered, the wrap of cable let loose and weight of the feed chute shifted to employee, causing a lumbar strain.

Employee was found at bottom of stairs on ground level in office stairs; cause of alleged accident is unknown. EMS was called and employee was given a clean bill of health and released. Employee's statement: fall resulted from a shove. EMS never treated EE. The local fire dept. rendered first aid; the assesment was elevated blood pressure and heat stress.

EMPLOYEE IS GOING INTO SURGERY ON 02/15/2010 TO CORRECT A SHOULDER IMPINGEMENT THAT OCCURRED 0N 07/04/2006. LOST TIME STARTED ON 02/16/2010.

Partial quote from IE statement, "Cleaning debris from kiln feeder riser. I was being supervised by A.R.S.I., he instructed me to manually clean debris . . . As I was removing a brick fell smashing my right index finger."

E/E was removing bolts from under a cement cooler, as employee pulled on a 3/4 ratchet he felt a pull in his (R) Shoulder

Employee states "while riding on a riding lawn mower a spider bit my right upper leg."

Standing outside of a truck bed reaching inside to pull out a tool. Struck elbow on the truck bed while extracting the tool.

Standing erect reaching approx. 1.5 feet in front to loosen an oil filter when sensed a pain in lower back.

Employee was clearing a pile up of bags. The bags shifted and he slipped striking his knee.

Tightening a bolt when the wrench slipped off striking the face.

EE shoveling spilled material ground to shoulder level and strained shoulder.

Carrying a box descending a stairway. Misjudged last step, fell, impact to left knee.

Staging pallets utilizing an electric lift truck. While reversing the lift truck it over- traveled and pinched the employee's hand between a guardrail and the handle of the lift truck.

Employee was inspecting post maintenance repair of the raw meal feed sampler. During the operational test the sampler mixer unexpectedly activited.

EE had filled a pill press with sample material. He installed the top cap but noticed it was cocked to the side. When he reached to correct it his lab coat inadvertantly caught the power handle causing the machine to activate. This spewed the sample material into his eye.

EE was dispatched to unplug a feed chute. After clearing the obstruction, he turned to manually run the machinery and he felt a pop in his left knee.

Utility personnel dispatched to inspect high-temp alarm on L-23 belt conveyor. When they arrived, the conveyor belt was on fire dropping burning rubber to he ground starting a grass fire.