Buscar en el registro

EE's description, 'While cleaning up from a job at 4:50pm in Alesa 1 building I was putting away my tools. While trying to remove a bit from my drill. My glove became caught on the drill and spun my glove with my fingers backwards. This resulted in spraining my ring finger on my left hand. Gloves where brand new from issue less than an hour old.'

An operator was standing on the tracks of a bulldozer, when the operator inside the cab, accidentally hit the travel lever. The operator had foot pinched between the tracks and the dozer frame. EE broke 3 toes on left foot. One was removed at the hospital Friday night. Expected to make full recovery.

The worker went to a mill bin to get the cement to flow. He attached high pressure to the internal air pads and tapped on the bottom to loosen the material. While checking for flow at the discharge, the seal came out from under the holding seal band and blew cement on him knocking off his safety glasses and getting into his eyes.

EE USED A WELDING ROD TO HOLD THE LARGE SOCKET ON THE WRENCH AS DID EVERYONE ELSE. AS HE WAS RELEASING ENERGY BY RUNNING THE WRENCH OUT OF AIR, THE WRENCH HE WAS HOLDING SLIPPED AND HIT THE MI LL AND BOUNCED TOWARD HIM. SPINNING SOCKET HIT HIS RIGHT KNEE AND THE WELDING ROD PUNCTURED HIS JEANS AND SKIN.

EE WAS PACKING MATERIAL WHEN PACKING SPOUT TURNED AND CAUGHT HIS RIGHT HAND IN BETWEEN THE PACKING SPOUT AND THE BAG CAUSING LACERATION AND CONTUSION.

A MECHANIC OTHER WAS WORKING ON THE CLINKER CRUSHER AND TURNING THE CRUSHER. EE REACHED UP TO HELP HIM AND GRABBED THE BELT AND STARTED PULLING EE S HAND GOT CAUGHT BETWEEN THE BELT, SHEAVE AN D THE GUARD. THREE FINGERS WERE CRUSHED ON HIS RIGHT HAND.

EE WAS USING A JACKHAMMER TO BREAK UP LUMPS OF MATERIAL WHEN A LUMP GAVE WAY, CAUSING THE JACKHAMMER TO SHIFT ANDF HIT THE 4EE'S RIGHT INDEX FINGER, BADLY BRUISING THE FINGER.

EE WAS CHIPPING AT THE BOTTOM OF THE CLINKER TANK WITH A CHIPPING GUN TO CLEAR MATERIAL AWAY. LARGE PIECE OF CLINKER BUILDUP FELL ON EE'S ARM.

EE REQUESTED MEDICAL ATTENTION FOR SWOLLEN ARM ON 10/18/96 IN THE AFTERNOON. AT THAT TIME, HE INFORMED SUPERVISOR THAT PARTICLES FROM A GRIND WHEEL HAD STUCK IN HIS LEFT ARM WHILE GRINDING S TEEL ON 10/02/96.

EE WAS AIR ARCING. THE AIR BLEW DEBRIS BEHIND SAFETY GLASSES AND SHIELD INTO HIS LEFT EYE.

MILL LINER HUNG UP ON DOOR OPENING AS CRANE WAS LIFTING THE LINER, WHICH CAUSED ENOUGH STRAIN ON THE CABLE TO CAUSE IT TO BREAK AND DROP THE LINER.

EMPLOYEE TRIED TO REMOVE LABEL WHILE MACHINE WAS ON PAUSE. WHEN EMPLOYEE TRIED TO RELEASE PAUSE MODE, THE ARM CAME OUT AND CRUSHED RIGHT HAND BETWEEN ARMS AND AIR JETS.

EE WAS TRYING TO RESET PALLET LABELLER PRINTER WHEN ARM EXTENDED TRAPPING HAND BETWEEN ARM AND CASING.

EE WAS USING A GRINDER TO CLEAN MATERIAL OUT OF A MIXER. HE DID NOT REALIZE THERE WAS ANY PROBLEM WITH HIS EYE UNTIL HE WENT HOME. AT APPROX. 6 P.M., HIS EYE BEGAN TO BURN. HE THEN VISITED THE DOCTOR, WHERE A METALLIC FOREIGN BODY WAS LOCATED AND REMOVED FROM HIS LEFT CORNEA.

EMPLOYEE WAS HOLDING ANGEL IRON FOR ANOTHER EMPLOYEE WHO WAS WELDING AT UNLOADING DOCK AND SPARK OR FLASH CAUSED EYE INJURY, WHICH WAS NOT FELT UNTIL ATER IN THE NIGHT AFTER GOING HOME.

EMPLOYEE WAS UNLOADING RAW MATERIAL. EMPLOYEE SAW DUST LEAKING FROM LINE FITTING. AS HE APPROACHED, LINE BLEW OFF, BLOWING QUICK LIME IN HIS EYES.

WHILE WATCHING TH OPERATION OF THE PALLETIZER FOR REPAIRS NEEDED,EMPLOYEE PLACED HIS HAND ON THE SIDE SQUEEZER RACK GEAR END SHAFT AND IT EXTENDED OUT,PINCHING HIS FINGER BETWEEN THE RACK GEAR AND THE SUPPORT TUBE.

REACHED OVER TO CUT OFF MAIN AIR VALVE & TRIPPED AIR SWITCH FOR PINCH TUBE CYLINDER WITH LEG. FINGER WAS IN PINCH POINT WHEN CYLINDER WAS ACTIVATED.