Incidentes mineros en Virginia

The injured employee was performing maintenance on a rock crusher using a cutting torch when a fire occurred. The injured employee received burns to EE's body and which ultimately proved fatal.

Employee was struck-by a rock in the 2 Right crosscut of the 16 East Section, while traveling under unsupported roof.

The sub-contractor was found unconscious in EE's vehicle by EE's co-worker. The car was locked, co-worker attempted to wake EE. Co-worker called 911, then got mine superintendent, who came to the scene, broke the window, removed EE from EE's car, and started CPR. EE was then pronounced deceased at the hospital.

Fatal injury to a temporary employee with Gillman Services, Inc was experienced when they were engulfed by a flow of lime kiln dust while operating a CAT 336 Excavator.

EE was in the process of opening a 6' thick slab. Water bags were installed at the top of the slab. EE was not wearing a safety harness and was about 20' high. Slab broke and fell down & hit EE and crushed him.

On 9/21/16, evidence suggests that the victim, an experienced mechanic, may have been attempting to remove or loosen the top drive power head, spindle cap on the drill machine to replace damaged seals by attempting to use a pipe wrench and hydraulics of the drill machine, which are controlled by levers in cab next to platform. Victim struck in torso by pipe wrench. No eyewitness.

Associate backed the haul truck under the conveyor to load Mineral filler. Preliminary findings indicate that the associate climbed to first level platform under the silo hopper. While standing on the platform, the upper section of the hopper detached from the silo. The entire hopper, along with contents, then collapsed onto the platform, engulfing the associate.

Employee was in the process of conducting his pre-shift exam on the section when he was found by another miner. He was pinned between a fallen rib and shuttle car that had been parked in the crosscut. The incident was not witnessed. Material that dislodged from the rib appeared to have struck the foreman on the right side of his body which resulted in fatal injuries.

EE shut down crushing plant to remove a drill bit stuck in the jaw crusher. He was using a torch to cut off drill bit when the bit flew up into his chest & face. He was hospitalized and died on 1/17/15.

The employee was working on a Fletcher roof bolter. He had the panel board off trouble shooting inside the electrical components of the machine. He apparently came in contact with electricity. The investigation is not complete at this time.

Excavator was lifting plastic pipe when it fell and hit the victim.

Employee was tramming continuous miner from #4 heading toward #1 heading when he was caught between the conveyor boom and the rib. There were no eyewitnesses.

The IEE was operating a supp. motor and was helping move a shuttle car. Shuttle car caught a fire valve and broke the fire valve off. The damaged fire outlet was isolated from the main water supply before repairs were started.The IEE was helping re-install the fire valve when the valve blew off and hit the EE over the lt. eye and forehead, causing lacerations,fractures.

Excavator was working in Redwine pit, highwall collapsed causing rock to fall on excavator. This caused a fatal injury to operator.

The individual was struck by a rib roll measuring approximately 20' long X 2' thick X 4 1/2' wide causing crushing injuries.

Employee was marking locations to install roof bolts, a piece of slickensided rock fell striking the employee's head and crushed his head against the drill station canopy.

The victim was positioned next to the continuous mining machine operator in the No. 7 Heading of the 1 North (about 95'inby S.S.#597). The final shuttle car was being loaded from the face of the place, when a piece of roof bolted rock measuring about 71" long X 39" X 18" thick fell, striking the victim. The injuries received from the occurance were fatal.

The truck owner was replacing a bolt in a pony axle. The owner had a bottle jack under one axle tire and a wooden block under the axle tire beside it. The owner then lowered the axles from the cab, positioned himself on a creeper between the 2 raised axle tires. The jack came out from under one axle tire; crushing the owner.

Employee was removing hydraulic line on Volvo loader. He had raised the bucket, remove front cover, taken 3 bolts out of line. The line then blew off then the main boom cylinder came down on top of him pinning him between differential and boom causing accident.

The employee came into contact with a guy wire, which broke loose and came in contact with an energized condutor on the pole. There was no insulator or proper anchor on the guy wire, this caused the employee to be electrocuted.