Buscar en el registro

The injured EE suffered a hand laceration while cutting a piece of steel (ball screw) while cutting the screw it snapped and cut the injured EE right hand resulting in stitches to the EE's right hand index finger knuckle

EE attempted to retract a magnet carriage into place. The carriage did not fully retract as prompted. EE performed LOTO and opened the hatch to the magnet to then find the magnet half closed. EE attempted to maneuver the carriage to return it to an open position simultaneously the cylinder actuated closing the carriage on EE's right hand. EE suffered a contusion.

While unplugging a mill circuit, the miner removed a guard, and the motor belt contacted miner's right thumb and severed it at the knuckle.

A Temporary employee was in process of loading an incoming truck, when the mast chain drive became loose by hitting a bump on the roadway. They decided to try and put the chain drive back in place by placing their left hand inside the chain pulley, when the pulley snapped back in place, catching the left finger, causing a fracture.

Mechanic was in the process of removing the sump lid to gain access to the sump by using an electric winch to move the 400 pound lid out of the way. Upon freeing the lid, it moved and caused left hand to be caught between the edge of the lid and an electrical panel mounted to the wall, resulting in a contusion type injury requiring stitches

A Calcium Department Employee was vacuum cleaning up lime that had accumulated below the briquetting area. When removing the lid of the vacuum system, lime dust particles were released into his face and into his eyes. As a result of getting lime particles in his eye, the employee received a corneal abrasion.

Employee was adjusting carousel brake on an overburden drill. He was leaning against the carousel with his left hand as he applied an impact wrench to the brake adjuster. The carousel moved enough to pinch his left hand. He jerked his hand out and a rough surface caused a partial skin avulsion to his palm. The doctor decided to apply stitches.

Worker was operating overburden drill near a highwall, when three (approximately 2-3") rocks struck side windows on cab, causing fractures in the glass. The fractures released very small glass particles into the cab which entered the worker's eyes, resulting in corneal abrasion.

A hydraulic chain wrench was being used to loosen the hammer on an overburden drill. The threaded portion of the end of the chain wrench broke, swung around, and struck the employee in left shin, causing a small puncture wound.

While arc welding inside the dryer at the secondary and crusher dryer, EE's eyes were exposed to flashes reflecting off the very shiny stainless steel inside dryer. Flashes came in from back of welding helmt. Reportable due to prescriptiong antibiotics to prevent infection.

EMPLOYEE CHARGED & DISCHARGED 5 FURNACES DURING THE DAY WEARING GOGGLES. HIS EYES FELT DRY DURING THE DAY. ON HIS DRIVE HOME THE SUNLIGHT WAS IN HIS EYES & HIS EYES BECAME SEVERELY IRRITATED & STUNG. HE WAS TREATED AT AN E.R. & THE FOLLOWING DAY AT OUR OCCUPATIONAL DR.

Employee was walking to the tool room to return some equipment. She had to pass through the fabrication area. She tried to shield her eyes from the grinding, but felt something in her eye. A foreign body was removed; she was treated for conjunctival infection and given prescription medications as treatment.

EMPLOYEE FILLING SUPERSACKS WITH LIMESTONE IN THE SCREEN STONE DEPT., GRABBED THE SACK W/HIS LT. HAND, BACK FACING SACK & PULLED TO SWIVEL SACK EVEN W/PALLET BELOW WHEN THE PIN FROM THE CLEVIS CAME OUT DROPPING THE SCALE, SACK FRAME & 2000 LB. SACK STRIKING THE EE ON THE BACK LEFT SHOULDER.

EMPLOYEE WAS UNDER THE HEAT EXCHANGE FOR KILN #4 ATTEMPTING TO REMOVE THE BELLOWS FROM THE HEAT EXCHANGE TUBES USING AN AIR HAMMER. ONE 30' TUBE LOOSENED IN THE TUBE SEAT AND FELL STRIKING HIS LEFT THUMB WHICH WAS HOLDING THE AIR HAMMER. HE RECEIVED SEVERAL STITCHES AT THE LOCAL HOSPITAL AND WAS GIVEN MEDICATION.

EE INJURED RIGHT HAND USING POWER WRENCH TO CLOSE DOOR ON RAIL CAR. EE WAS TREATED BY MD AND WAS RELEASED TO MODIFIED DUTY NO USE OF RIGH HAND. EE WAS GIVEN A PRESCRIPTION FOR ANTIBIOTIC WHICH HE DID NOT HAVE FILLED. UPON FOLLOW UP MD PLACED EE OFF OF WORK DUE TO INFECTION.

EE USING HAND DRILL TO DRILL HOLE IN STEEL. DRILL BIT CAUGHT ON WELD AFTER MAKING HOLE. DRILL TWISTED OUT OF EE'S HAND AND STRAINED MIDDLE FINGER OF RIGHT HAND MIDDLE FINGER BECAME SLIGHTLY SW OLLEN BY NEXT DAY. SENT EE TO MD WHERE HAND WAS WAS EXAMINED. EE RELEASED TO MODIFIED DUTY LIMITED USE OF RIGHT HAND FOR ONE WEEK.

EMPLOYEE WAS WELDING A GUARD IN THE WELDING BOOTH IN THE MAINTENANCE SHOP. HE STOPPED WELDING AND LIFTED HIS HOOD TO OBSERVE HIS WORK. THE WELD POPPED AND A PIECE OF SLAG WENT BEHIND HIS SAFET Y GLASSES AND INTO HIS LEFT EYE. HE RECEIVED PRESCRIPTION MEDICATION FOR HIS EYE.

WHILE ATTEMPTING TO PUSH A PIN AND BEARING ASSEMBLY FROM ITS HOUSING USING A MECHANICAL PRESS AND A BOLT AS A SPACER, THE BOLT AND HOUSING ASSEMBLY KICKED OUT STRIKING EE ON THE RIGHT SIDE OF HIS HEAD.

EE WAS MOVING BRUSH WHEN FELLOW EE NEARBY WAS USING A CHAINSAW TO CLEAR BRUSH AND TURNED AROUND AND GLANCED EE'S FOREARM WITH CHAIN.

WHILE DRILLING OUT THE DIESEL GUN PART FOR #3 KILN LIGHT-OFF, THE DRILLED LIME PARTICLES BLEW BACK AND MADE CONTACT WITH EE S RIGHT FOREARM. THE LIME CALCIUM OXIDE STRUCK TO THE ARM AND DISOLV ED IN THE PERSPIRATION CAUSING SKIN BURNS.

EE WAS TRYING TO UNPLUG DUST COLLECTOR & PLACED HAND IN PIPE TO DUST COLLECTOR CHUTE AND FINGER TOUCHED BLADE OF ROTARY AIR LOCK.

EE EXPERIENCED EYE IRRATIATION.

EE DRILLING A HOLE IN A PIECE OF VERTICAL MOUNTED PLATE STEEL. MAGNET CAME LOOSE. FROM STEEL CAUSING DRILL TO SLIP DOWN ONTO RIGHT RING FINGER.

EE WAS CLEANING UNDER A DRYER WITH AN AIR CHISLE. THE HOSE ON ANOTHER EE AIR CHISLE CAME OFF AND BLEW SOME MATERIAL UNDER HIS CO-WORKERS SAFETY GLASSES AND INTO HIS RIGHT EYE. THE OPTOMOLOGIST HAS TO REMOVE A PARTICLE FROM EE'S EYE AND HE WAS GIVEN A PRESCRIPTION MEDICATION.

OPERATING ELECTRIC POWERED FLOOR JACK (HANDHELD)CARRYING CROWN PULLER ON FURNACE FLOOR, WHEN THEWHEEL HIT DIP/GROOVE IN FLOOR AND HANDLE WAS JERKED OUT OF HANDS AND HIT LEFT THIGH.

EE WAS CUTTING BROKEN CROWN AT 200 TON PRESS. CALCIUM PIECE STUCK TO BLADE AND FELL ON LEFT HAND WHILE REACHING FOR CALCIUM ON CUTTER SURFACE.

REPLACING PAD ON PUSHER BAR IN THE AUTOMATIC PACK CENTER. PAD IS MOUNTED ON RETRACTABLE FLAPPER. WHEN EE WENT TO REMOVE OLD PAD AND IN THE PROCESS OF TIGHTENING UP THE NEW PAD, THE ELECTRIC EY E WAS ACTIVATED. WHEN SAW MOVEMENT(HAND) AND ACTIVATED THE FLAPPER AND PINCHED EE HAND.

EE WAS GRINDING THE TIP OF A SHEAR PIN AND IT APPEAR THAT HE PIN WENT INTO THE GRINDING WHEEL IN THE ARE TO THE SIDE OF THE WRENCH THE PIN CAME AROUND THE WHEEL AND HIT THE EE ON THE TOP OF TH E LEFT HAND X RAY ON THE HAND WERE NEGATIVE. EE WAS PLACED ON RESTRICTED WORK ON 1-31-00. 1

EMPLOYEE WAS STARTING LOG CHIPPER. PULLED CLUTCH CABLE AND CABLE BROKE. WRIST HIT RAILING.

EE UNPLUGGED BAG SPOUT OF RAYMOND MILL PACKER AT WHICH TIME LIMESTONE MATERIAL(WHICH HAD BEEN HEATED UP DUE TO FRICTION FROM THE IMPELLER) POURED OUT BURNING HIS LEFT WRIST/FOREARM. THE MAINTE NANCE DEPT. HAD BEEN WORKING ON THE PACKER DURING THE PREVIOUS SHIFT. PREVIOUS SHIFT SHOULD HAVE DE-ENERGIZED THE EQUIPMENT TO PREVENT THE FRICTION BUILD UP OF HEAT.

USING A CUTTING TORCH TO REMOVE A PLUMBING FITTING. SMALL PIECE OF METAL DEFLECTED SAFETY GLASSES AND BECAME EMBEDDED IN EMPLOYEE'S RIGHT EYE.

PLUGGED HEAT EXCHANGE. FOREIGN BODY IN EYE.

EE WAS PUSHING CROWNS. CALCIUM DUST FROM A CROWN BLEW INTO HIS EYE FROM THE FAN BLOWING IN HIS DIRECTION.

DENSIFIERS WERE LEFT RUNNING, LACK OF PROPER PERSONAL PROTECTIVE EQUIPMENT PULSATING NOISE IN EAR. RECD MEDICAL ATTENTION & PRESCRIPTION

EMPLOYEE WAS CHANGING LOG CHIPER BLADES. HE WAS BACKING A STATIONARY BLADE OFF TO CLEAR CALCIUM SO HE COULE TURN THE ROTOR. WHEN HE BROKE TORQUE ON THE NUT HE STRUCK A NEW BLADE WITH HIS HAND. NEW BLADES WERE IN THE IMMEDIATE WORK AREA WITHPROTECTIVE TAPE REMOVED.

EE WAS REMOVING STEEL THAT HAD FLASHED OUT IN MACHINE. THE PARKED ON THE STEEL AND WHEN IT POPPED LOOSE, HE CUT HIS ARM ON THE STEEL STILL CAUGHT ON MACHINE. EE WAS WEARING GLOVES.

EE WAS ASSIGNED TO WELD A METAL BAR INSIDE A RECLAIM HOPPER. HE SPRAYED THE HOPPER SURFACE WITH CARBURETOR CLEANER, THEN WIPED IT OFF. WAITED A FEW MINUTES, LIT A CUTTING TORCH & STUCK IT INSI DE THE HOPPER. FLAMES FLASHED OUT & SINGED HIS LEFT FOREARM & HAND.

ARC FLASH

EE WAS OPERATING CLADDER MACHINE. WAS HANGING STEEL ON MACHINE (PAY OFF END). WAS NOT WEARING GLOVES. COIL MOVED & CUT HIS HAND ON A SHARP STRIP PROTRUDING FROM COIL.

EMP WAS USING A HAND GRINDER, HOLDING IT ON ITS SIDE WHEN WHEEL CUT HIS LEFT HAND. GRINDER WAS BING USED WITHOUT A GUARD.

EMP WAS SCREENING CALCIUM. REACHED UNDER SCREEN TO GET BLOCKING PLATE WHICH HAD BEEN IMPROPERLY STORED THERE. PLATE HIT THE COUNTER WEIGHT WHICHWAS UNDER THE SCREEN. PLATE WAS KNOCKED OUT OF E MPS HAND AND THEN HIT EMPS HAND.

EMPLOYEE WAS CUTTING A STEEL PLATE OUT OF CHUT EABOVE EAST SCREEN AT SCD. HIS HEAD WAS TURNED DUE TO CLOSE CONDITIONS. HOT STEEL LANDED IN HIS RIGHT EAR.

THE CONDENSOR THAT WAS BEING PULLED WAS STUCK. THE HYDRAULIC CYLINDER TIPPED UP CATCHING EMPLOYEE'S FINGER BETWEEN THE FRAME AND HYDRAULIC HOSE.

EMPLOYEE WAS STANDING BETWEEN THE BREAKER AND THE CRUSHER HOOKING UP CHAIN UP TO BREAKER. CRUSHER OPERATOR MOVED THE BREAKER AND EMPLOYEES LEG WAS CAUGHT BETWEEN THE ROCK BREAKER AND THE CRUSH ER.

EMPLOYEE WAS WELDIN ON #2 RAYMOND MILL. NYLONG SLING HOLDIGN UP WIND TUNNEL MELTED CAUSIGN WIND TUNNEL TO FALL STRIKING EMPLOYEE ON LOWER LEFT LEG. THE NYLONG SLING GOT HOT AND CAME APART.

EE WAS OPERATING A DRILL PRESS AND ACCIDENTLY HIT THE FOOT PEDDLE THAT STARTED THE MACHINE AND HE CUT HIS LEFT HAND REQUIRING MULTIPLE STITCHES AND PRESCRIPTION MEDICATION.

EMPLOYEE HAS A PRE-EXISTING, NON-WORK RELATED EYE CONDITION CALED IRITIS. WELDING AGGRAVATED THE IRITIS. EMPLOYEE WAS WELDING AT A TIME WHEN HIS CONDITION WAS BOTHERING HIM, THUS WORSENING THE EYE IRRITATION.

PRESSURIZED HOSE RELATED TO FURNACE FLEW, SPRAYING STEAM WATER. EMPLOYEE MAY NOT HAVE HAD PRESURE PROPERLY ACCOMODATED.

EMPLOYEE WAS BLOWING DUST AND GRIT OFF FROM LOADING PLATES WHICH HAD STUCK OPEN. HE PLACED HIS RIGHT FOOT ON TOP OF A FILLED BAG, LOCATED ON A PALLET WITHIN THE LOADING ELEVATOR, AND CONTINUED TO BLOW OFF THE GRIT. THE TENSION ON THE PLATES WAS REMOVED AND THEY SHUT AROUND EMPLOYEE'S ANKLE.

EMPLOYEE WAS OPERATING A SEMI AUTOMATIC PALLETIZING SYSTEM. AS BAGS ENTER THE PALLETIZING TABLE THEY CROSS OVER FOUR UNPOWERED ROLLERS. THE EMPLOYEE SOMEHOW CAUGHT HIS GLOVE ON THE THIRD UNPOW ERED ROLLER. THE FORCE OF THE BAG CAUSED HIS THUMB AND WEB AREA TO GO BETWEEN THE 3RD AND 4TH ROLLERS. AS EMPLOYEE PULLED HIS HAND BACK IT BECAME LACERATED BETWEEN THE FOREFINGER AND THUMB.