Buscar en el registro

EE had driven wedges between bucket and cutting edge while torching off bolts. The cutting edge sprang forward and caught the ee in the knee. This caused bruising and swelling in his knee later that evening.

The impact crusher had stalled leaving rock lodged inside. Employee's were rolling boulder out of impactor when employee's hand was caught cutting his finger. The two employees were not communicating together and the rock slid onto the employee's hand causing the injury.

Employee was lifting drill steel to put into changer when his wrist popped. He had hurt his wrist the privious year while working at home. Employee went home that evening and came to work the next morning & said he experienced more pain. After a doctor's visit it was determined to be a sprain.

Employee was holding a cylinder with his left hand. While trying to set it in place, cylinder hung up and became dislodged. This caused the cut to his hand. The cut to his hand required 6 stitches.

He was grinding a piece of metal to weld. The wind blew a piece of metal behind his safety glasses. The metal couldn't be flushed from his eye.

The wind was blowing hard while they were changing screens. Some dust blew into employee's eye. Later that evening, his eye started bothering him more so he went to the hospital to have the dust removed.

Employee works in the office and does not run equipment. He stated that he wears proper hearing protection when needed. He believes that the hearing loss is due to hereditary causes because other members of his family have hearing loss.

Employee stated that he has been wearing proper hearing protection while working around equipment. Employee also stated that he has started to wear hearing protection while working at home. He is unsure why there was a change in his hearing.

Employee stated that on the day of the hearing test he had a head cold which may have affected the results. He has been wearing proper hearing protection at work & does not believe he has been over-exposed at work.

Employee stated that he skipped the 2007 hearing test so two years went by between tests. He stated that he had been wearing all hearing protection needed while running equipment. He believes his age has played a part in the hearing loss.

Employee was lifting a cover weighing approx. 40lbx & his back was strained.

Changing the bolts on cutting edge using an inpact wrench, bolt spun and cut 2 fingers.

Changing screen panels on screen deck, removing chute and slipped and fractured finger.

LIFTING CUTTING EDGE WITH CHAIN.

HEAT EXHAUSTION - EE GOT DIZZY.

WHILE CHANGING SCREEN, EE STRAINED HIS NECK.

Getting out of loader left foot hit ground first, landed on rock twisted ankle.

Stepped out of manlift and twisted ankle.

Was clearing out an chute with a large pry bar and struck a peice of metal in 2nd and 3rd between the two. got 3 stitches.

USING A LADDER TO PUT A BOLT IN AN IMPACTOR II, EMPLOYEE STRAINED HIS BACK.

Was cutting crown bar rubber for an screen deck and slipped and cut top of 2 fingers.

EE WAS PULLING LARGE ELECTRICAL WIRES FOR THE NEW CONTROL HOUSE. HE WAS TRYING TO BEND THE WIRE AND HEARD A POP IN HIS RIGHT HAND.

Ok first was into he skid-steer cleaning up the plant, came into the parts trailer to eat lunch and hurt his back in the process of sitting down.

CHANGING GRATES IN HAMMERMILL AND SMASHED LEFT THUMB.

WHILE CUTTING A TREE LIMB WITH A 20" BAR CHAIN SAW, EE ACCIDENTALLY CUT HIS LEFT BIG TOE, WHICH REQUIRED 7 STITCHES.

EE WAS PULLING ON IMPACT ROTOR ON CRUSHER TO CHECK WEAR ON IMPACT HAMMERS HE FELT A PAIN IN HIS LOWER BACK WHEN HE PULLED ON ROTOR TO ROTATE IT.

EMPLOYEE ALLEGES HE WAS HOOKING WELDER TO PICK UP. BENT DOWN TO LIFT UP HITCH AND FELT SHARP PAIN IN LOWER BACK.

EMPLOYEE WAS WALKING ACROSS ICE COVERED PIT FLOOR AND SLIPPED ON THE ICE.

WHILE REMOVING A CONVEYOR FROM THE PORTABLE PLANT, EE LOST HIS BALANCE AND FELL 5' AND BROKE ANKLE.

EE WAS UNLOADING FILES AND LOADED TICKET BOXES FROM BED OF PICKUP TRUCK. FILES AND BOXES WERE BEING CARRIED TO STORAGE ROOM.

WHILE SHOVELING BASE ROCK-EE STRAINED THE MUSCLES IN HIS LOWER/MIDDLE BACK AREA

EE HELPING LIFT IMPACT CRUSHER HAMMERS ABOUT 200 EA WITH EE ONTO THE BED OF HIS PICK UP TRUCK, WHEN A SHARP PAIN HIT HIS BACK AND GROIN AREA.

ON 9/26/96, EE TWISTED HIS L KNEE WHILE MOVING ON OX BOTTLE BECAUSE HE STEPPED ON A ROCK. WAS SEEN BY COMPANY DR. & RELEASED BACK TO WORK. HAD PHYSICAL THERAPY UNTIL 11-3-95 ON A WEEKLY BASIS. HAD ARTHROSCOPY SURGERY DONE ON 11-3-95, THEN RETURNED BACK TO WORK ON 11-9-95.

AFTER MOVING THE AIR TRACK DRILL IN A POSITION TO START DRILLING A SHOT, HE WALKED DOWN THE SLOPE TO CHECK THE AIR COMPRESSOR AND WHILE DOING SO, LOST HIS FOOTING AND FELL TO THE GROUND, LANDI NG ON HIS RIGHT ELBOW, THUS CAUSING THE CONTUSIONS AND ABRASIONS.

EE WAS MOVING THE SULLIVAN ARC TRUCK DRILL TO THE FUEL TRAILER AFTER COMPLETION DRILLING OUT A SHOT HE CHOSED TO DRIECT THE DRILL DOWN DROP OFF (5FT SLOPE) INSTEAD OF THE RAMP THE DRILL TURNED SIDE WAYS CAUSING THE CRAWLER TRACK TO LOSE CONTROL WITH THE SURFACE THEN CAME TO REST ON HIS RT FOOT & TOES

UNKNOWN AT THIS TIME: EMPLOYEE WAS FOUND WITH HIS RIGHT ARM CAUGHT BETWEEN THE HEAD PULLEY AND CONVEYOR BELT WITH THE PULLEY STILL RUNNING. A FELLOW EMPLOYEE HEARD HIS CRY FOR HELP, CUT THE P OWER OFF, HE THEN FELLT OT HE GUARD BELOW, THAT WAS ON ANOTHER CONVEYOR TAIL PULLEY.

EMPLOYEE WAS HELPING TO LOAD A SHOT FOR BLASTING. HE HAD BEEN CARRYING 50# SACKS OF ANFO ON HIS SHOULDER AND HIP TO THE BLAST SITE FROM DELIVERY TRUCK. INJURY OCCURRED 11-29-94 BUT EMPLOYEE DI D NOT REQUEST TO SEE DR. UNTIL 12-5-94.

WHILE EMPLOYEE WAS EXITING PARTS STORAGE TRAILERHE LOST HIS FOOTING WHICH CAUSED HIS RIGHT ANKLE TO POP AS HE LANDED ON THE GROUND.

EE & SEVERAL OTHER EES WERE POSITIONING LARGE STEEL BEAMS INTO PLACE FOR WELDING, THEY WERE FABRICATING A [?] AXLE CHASSIS FOR A ROCK CRUSHER & FEEDER. HE STATED THAT HIS BACK WAS HURTING AFTE R HIS WORK SHIFT.

AGGRAVATED INJURY FROM ACCIDENT DATED 6-24-94, WHILE CLIMBING DOWN LADDER.

EE WAS INJURED IN COMPANY REPAIR SHOP WHILE USING A HAND GRINDER. LEFT HAND SLIPPED OFF THE CONTROL HANDLE AND THE MIDDLE OF ARM TOUCHED THE GRINDING WHEE, CUTTING A GASH APPROX. 2" LONG AND 3 /8" DEEP.

EMPLOYEE WAS ATTEMPTING TO R4EMOVE SPILLAGE (LOOSE ROCK) FROM CATWALK WITH THE INSTEP OF HIS RIGHT FOOT. (KICKING MATERIAL FROM CATWALK). WHEN HIS FOOT CONTACTED THE LOOSE ROCK HIS RIGHT KNE E PIPPED ON THE INSIDE AND PAIN CAME TO HIS RIGHT KNEE. SHOULD HAVE USED A SHOVEL.

EMPLOYEE WAS CLEANING TAIL SECTION ON THE PRIMARY CONVEYOR WITH A SHOVEL. HE STATED TO THE SUPERINTENDED THAT HIS BACK STARTED TO HURT WHILE SHOVELING THE DAM AND WET MATERIAL FROM THE AREA.

EE WAS BUILDING UP HAMMERMILL HAMMERS AND WAS PUTTING THE LAST PASS WITH HARD FACING RODS AFTER WEDDING THE HAMMER HE STOPPED LIFTED HIS WELDING MASK AND WAS STRUCK IN THE LEFT EYE WITH A HOT FLAKE OF WELDING SLAG AS THE SLAG COOLED DOWN.

PICK UP SLAB ROCKS HURT BACK

EE WAS FABRICATING SAFETY HANDRAIL AROUND ENGINE PLATFORM WHEN HE LOST HIS FOOTING SLIPPED AND CAUSED AN ACUTE SPRAIN TO HIS RIGHT FORFOOT BALL AND BIG TOE.

EMPL WALKED UP CATWALK TO THE RINSE SCREEN.LOST FOOTING ON SOME ROCKS,SLIPPED & FELL ON CATWALK CAUSING INJURY TO LEFT HAND THUMB.

THE SUPERINTENDENT AT THIS MINE STATED THAT HE ATTEMPTED TO LIFT AN I BEAM & HURT HIS BACK