Buscar en el registro

employee slipped on wet ground and sprain left ankle.

The employee and a contractor were removing an inspection cover from the top of the clinker cooler drag-chain. The employee's tip of pinky finger on left hand became pinched between the bottom of the cover and a metal flange as they placed the cover on the ground. The employee's fingernail was almost avulsed from the nail bed

Employee was pushing a small pile of material with their right foot in a sweeping motion, when their left foot slipped on loose material. Instead of falling forward, they leaned back and turned their body in a twisting motion, during which time they felt a pop in their knee.

Employee was bending over to pick up a trash bag from a box that was on the floor. The employee did not notice a metal pipe that was next to the box on the floor and as the employee bent down to pick up a trash bag, EE's left forehead came in contact with the end of the metal pipe resulting in a laceration to the top left side of EE's forehead.

As the employee was stepping out of the raw mill, the employee placed a hand on the raw mill tire hook and disrupted the accumulated dust causing it to become airborne. The airborne dust entered the airstream of the cooling vent fans and blew onto the employees face and under safety glasses causing dust to enter left eye.

Employee was walking backwards down the backside of the clinker dome access ramp when EE felt a strain in EE's right knee. The employee continued to experience pain in EE's knee and was referred to an orthopedic specialist for further diagnosis and evaluation.

Employee was opening the water truck cab door to open the water tank fill valve when the tip if EE's right fifth finger got wedged in between the cab door frame and the water fill tank valve resulting in a laceration.

Employee was using a prybar to open the southeast door to raw mill separator. The prybar slipped causing EE's middle finger to become wedged between the prybar and the platform handrail.

Employee was working on the conveyor gallery reaming some holes at the time of the incident. EE had left the impact gun on the top beam of the conveyor while coming down to grab some tools. EE had a hand on a lower beam at ground level and the impact gun that was left up top fell smashing EE's finger.

EE straddled the finish mill 1 pinion shaft bearing drive line guard to access the oil level plug located on the opposite end of the platform. They had their left leg on the platform and as they swung their right leg behind them they felt a pop in their right knee as they planted their foot on the platform. There is ladder access on the opposite end to access the oil plugs.

The metal fork (1 inch X 24 inch) that supports the empty bags on the portland bag applicator was bent in a downward angle approximately 2 inches and as the employee attempted to lift up and straighten the fork the employee felt a pop below right shoulder

Employee was walking on a flat wet paved road carrying 2 shovels over right shoulder when EE's right foot slipped causing EE to lose balance and fall to the ground in a backward twisting motion.

Employee was using a shovel to move a large chunk of clinker from the back of the clinker hopper grating to the front. As the employee was using the shovel to move the chunk of clinker, EE felt a pain in lower back.

Employee was pulling down with a pipe wrench in right hand, while holding a 1/2 inch pipe fitting with a pair of channel locks in the left hand. The employee heard a pop in the back area of left shoulder while applying downward force with right hand while trying to loosen fitting.

Employee was engaging locking mechanism to secure the raw mill doors when some dirt from area above EE fell behind the upper part of EE's safety glasses frame and entered the employee's left eye.

Employee was standing on a ladder closing a door shut on ball mill inlet throat. The door was not secured in place and as employee stepped down the ladder the door swung open striking employees hard hat.

A production utilityman was cleaning the walkway along the lime/gypsum conveyor belt. While cleaning the walkway, they slipped on material and fell onto elbow causing a laceration requiring 4 stitches.

Maintenance employee was performing tracking adjustments on the palletizer belt. The employee had a hammer in right hand and was holding on to the belt frame with left hand. As the employee began to tap on the belt roller with the hammer, the hammer was caught by the moving roller and the employee's upper arm became pinched between the roller and conveyor belt.

Employee was removing the bottom of an air slide pan that was with 3 other employees. They were using 2 come-a-longs to lower the airslide pan. The come-a-longs were then removed leaving the airslide pan supported by the pipe structure. The employees lifted the pan, the pan slipped and employee reached out at an awkward angle and felt discomfort in stomach.

Employee was holding a 3/4 inch conduit strap with left fingers and a cordless band-saw in EE's right hand. The band-saw was partially resting on a cardboard box, as EE began to cut the conduit strap the cardboard box shifted causing the band-saw blade to come in contact with EE's left index finger causing a laceration to right index finger requiring 3 stitches.

Employee proceeded to walk to the north side of preheater tower and on the way back to work area, right foot got caught on a scaffold gate that was laying on pathway floor causing right leg to twist resulting in a trip and fall on right knee landing on scaffold pipe knuckle attachment that was secured to scaffold gate.

Employee was using an air lance to poke through a thermocouple port opening on a plugged preheater tower cyclone, when the air was turned on to the air lance, hot material poured out of port opening splashed on employees Nomex hood around the right ear and face area. The heat from the hot material radiated through the Nomex hood and caused burns to both these areas.

At the request of the Alamo employee, a contractor tossed a 22 lbs. box of ceramic fiber insulation across the raw mill roller pair to the Alamo employee. The Alamo employee had left arm extended and lying across the roller pair seal air fan hose. The employee heard a pop in elbow area as arm hyperextended when the box made contact with the left arm.

Employee had just closed air valve on an air line on 3rd floor of preheater tower. As EE was walking away from area, EE felt dust fall into left eye. Employee is unsure where dust came from.

Employee was opening a port on preheater tower cyclone, when a piece of coating fell and forced some material to come out of port. Some of this dust got into employees right eye.

Employee was tapping on the seat of a metal tipping gate with a hammer to try and loosen material because the gate would not fully close. During this process the gate closed crushing employee's right index finger against hammer and gate flap.

Employee was cleaning the preheater tower using the water blaster. During this cleaning a large chunk hit water blaster lance causing it to twist while employee was engaged with gun trigger. The trigger part of the gun also twisted along with employee's left hand ring finger, causing a fracture of tip of left ring finger.

EMPLOYEE WAS CLEANING ON PAVED AREA ALONG DRAINAGE DITCH, MIS-STEPPED AND LANDED ON KNEES.

EMPLOYEE WAS LIFTING CEMENT MOLDS CONTAINER OUT OF MOISTURE CABINET WHEN EMPLOYEE FELT PAIN IN NECK AND SHOULDER AREA.

EMPLOYEE WAS DESCENDING FROM HAUL TRUCK LADDER WHEN EE'S FOOT SLIPPED ON THE LAST MUDDY LADDER RUNG CAUSING EE TO FALL TO GROUND ON EE'S BACK. DURING THIS EE INCURRED A LEFT WRIST AND LEFT KNEE SPRAIN.

EMPLOYEE WAS WORKING IN THE RAW MILL. EMPLOYEE WAS HOLDING A LINER PLATE IN PLACE AS THE BOLTS WERE BEING CUT OFF FROM PLATE FROM THE OUTSIDE. THE PLATE SLIPPED AND AS THEY ATTEMPTED TO GRASP THE PLATE IT SLIPPED AND CUT THROUGH THE GLOVE CAUSING A LACERATION ON THE LEFT HAND PALM THAT REQUIRED 4 STITCHES.

EMPLOYEE WAS LIFTING A GUARD COVER TO RE-INSTALL IT ON THE MASONRY PACKER CONVEYOR WHEN EE FELT A PAIN IN LOWER BACK. THE GUARD WAS IN THE UPRIGHT POSITION LEANING AGAINST THE BELT FRAME, BUT HAD A FOOT OF CEMENT AROUND IT CAUSING IT TO BE HEAVIER THAN IT NORMALLY IS.

EMPLOYEE HAD JUST CLEANED A MATERIAL SPILLAGE INTO BOBCAT BUCKET. EMPLOYEE HAD ALREADY CLIMBED ONTO BOBCAT, BUT AS EE TURNED TO SIT INTO THE CAB OF THE BOBCAT, EE'S FOOT SLIPPED OFF OF STEP AND WEDGED BETWEEN BOBCAT BUCKET AND FRAME OF BOBCAT CAUSING EE'S RIGHT FOOT TO TWIST.

Employee was shoveling clinker out from under a belt conveyor counterweight. EE right foot slipped on a piece of clinker, causing ee to jerk to catch self and twisted back in the process.

A piece of plywood shielding board became dislodged and fell onto individuals L pinky finger resulting in a fracture.

EE was working changing a line on compressor, standing on skid at compressor. EE re-positioned right foot and left foot slipped on the steel and fell backward striking head on the concrete resulting in laceration requiring 8 staples.

EE was attempting to make a curtain over door window of excavator with a towel and slammed finger in door causing a fracture of right ring finger

EE was lifting a piece of metal plate flooring, approx 4'x5', weighing approx 100# to access work area. As EE slid the plate, EE lost grip & it dropped onto the fingers of EE's right hand. EE snatched EE's hand out from under the metal plate which caused the skin of EE's right forefinger to tear back, requiring 4 stitches. EE was not wearing any gloves at the time.

Employee was cleaning the burner pipe on the kiln with an air lance. As the employee was extracting the lance from the port, something fell and made an impact on the lance causing it to flip up and around and hit EE on EE's left wrist causing a hand sprain.

EE was inside the kiln moving a 2x12 board from across the kiln to the floor of the kiln. He picked up the board and tossed it to the side when it ricocheted off the rigging and landed on the top of his right foot causing his foot to swell. The ee was wearing steel toe boots at the time of the incident.

EE was repositioning forks on the forklift and felt a pop in his arm.

EE was walking down stairs carrying 2 empty 1 gallon buckets. He felt a pop in his right knee. He waited a few minutes and didn't hurt or bother him so continued on to collect samples. Didn't report until 2/9/15. Went to doctor & released to regular duty. Requested to return to doctor on 2/23/2015.

Employee was climbing down from 980 loader and reached the 2nd step when his foot slipped off of the step causing him to fall back onto the concrete slab. Employee was complaining of lower back pain.

Employee was clearing build up of material from discharge box for routine pm inspection when material that was above his hand broke free and fell and pushed his hand down onto the lip at the bottom of the door opening causing a laceration. The employee was wearing leather gloves and did not require stitches.

EE & contractor was working in the flow control gate area. After removing a valve they used a come-along to raise it from the floor to a working surface of just over 2 feet. The ee had his hand positioned on each side of the valve unit as the contractor was removing the come-along from above. The come-along slipped & fell down, landing on the ee's left thumb,causing a fracture.

EMPLOYEE WAS CHECKING THE PREHEAT TOWER WHEN AN AIR CANNON DISCHARGED PUTTING HOT AIR ON HIS LEFT ARM AND LEFT SIDE OF FACE. CAUSING BURNS.

EMPLOYEE WAS PLACING SCRAP METAL IN THE DUMPSTER AND CUT HIS LEFT RING FINGER REQUIRING STITCHES TO CLOSE WOUND.

EMPLOYEE WAS PULLING WEEDS AND CUT FINGER. THE CUT REQUIRED 3 STITCHES TO CLOSE.

THE EMPLOYEE, TRANSIT DISPATCHER FROM SCALE, WAS WALKING TO HER CAR AND TRIPPED ON A WATER HOSE, AND FELL TO GROUND. ACCIDENT RESULTED IN A FRACTURED RIGHT ELBOW AND LEFT KNEE CONTUSION. RETURNED TO WORK THE NEXT SHIFT.

EMPLOYEE WAS CHECKING THE TARGET ON A TIPPING GATE THAT LOOKED LOOSE, WHEN GATE ARM MOVED AND CUT HIS FINGER. REPORTED DUE TO STITCHES. NO LOST TIME.