Buscar en el registro

While employee was looking at project at tailpulley of Stacker belt, bungy cord holding S-O cord broke. Bungy came down and hit him on top of head.

Employee and a coworker were splicing a conveyor belt at the washplant. When the belt clamp was removed it fell on employee's right index finger

While employee was changing screens on washplant, his safety harness caught on spray bar. He slipped and strained his back.

Employee was driving haul truck when he hit a pocket of silt which jolted the truck. He experienced pain in lower back.

Employee was feeding crusher when going up ramp dropped a rock. When going down hit rock, jolting cab. Didn't feel stiffness until after work. Reported next morning to Leadman (10-06-04). Did not request medical attention from Company until 10-7-2004.

EMPLOYEE WAS INJURED IN A MOTOR VEHICLE ACCIDENT WHEN A 988F LOADER BACKED OFF THE WASH PLANT FEEDER RAMP AND STRUCK THE WATER TRUCK IN WHICH HE WAS SEATED. THE SPEED OF THE LOADER AT THE TIME OF THE COLLISION WAS WELL BELOW 5 MPH AND THE WATER TRUCK WAS STOPPED. THE EMPLOYEE WAS WEARING A SAFETY RESTRAINT AND HARD HAT.

EMPLOYEE WAS CLEANING AROUND A CONVEYER BELT. AS HE WAS SHOVELING HIS THUMB WAS CAUGHT BETWEEN A TROUGHM ROLL AND THE ROLL FRAME. THE EMPLOYEE'S THUMB WAS CUT AND REQUIRED TWO STITCHES.

EE STATES THAT AFTER WORKING A SHIFT, THAT INCLUDED CHANGING TAKE-UP ROLLS, HIS BACK BEGAN TO HURT. EE DID NOT NOTICE ANY SPECIFIC INCIDENT THAT CAUSED AN INJURY. HIS BACK DID NOT BEGIN TO HUR T UNTIL AFTER THE EE HAD BEEN HOME FOR SEVERAL HOURS.

CUTTING 12" CHANNEL. THE CHANNEL FELL AFTER IT WAS CUT, 3-4" AND HIT EE'S TOES. HE WAS WEARING STEEL TOES, BUT IT MISSED THE STEEL TOES.

EE WAS BENDING OVER LOOKING AT ONE END OF A PIPE. ANOTHER EE, AT THE OTHER END OF THE PIPE, HIT THAT END OF THE PIPE. THE PIPE POPPED UP AND HIT THE FIRST EE IN THE MOUTH. THE INSTRUMENT USED TO HIT THE PIPE WAS A PIPE WRENCH.

THE EMPLOYEE WAS CUTTING "FISH EYES" IN A 1/2 X6"X 20' STEEL STRAP WITH A CUTTING TORCH. THE STRAP WAS SITTING ON THE EDGE ON A 8' HIGH CONCRETE WALL. HE HAD THE STRAP TO FAR OVER THE EDGE WIT HOUT ADDITIONAL SUPPORT. WHILE HE WAS CUTTING THE HOLES THE STRAP TEETERED OVER THE EDGE FALLING APPROX. 3 FT. WHEN IT HIT THE GROUND IT ALSO IMPACTED THE SIDE OF HIS RIGHT ANKLE.

THE EE WAS HELPING THE SERVICE MECHANIC CARRY A BUCKET HIP WEAR PLATE TO THE LOADER FOR INSTALLATION. WHILE CARRYING IT HIS HAND BUMPED AGAINST THE MECHANICS THRU. THE WEAR PLATE IMPACTED HIS HAND AS IT WAS BETWEEN THE PLATE AND THE TRUCK. HE REFUSED MEDICAL TREATMENT UNTIL TODAY.

EMPLOYEE WAS CUTTING AN OLD PIECE OF CONVEYPOR BELTING TO MAKE A RE[PLACEMENT CHUTE EXTENSION FOR A DISCHARGE HOPPER ON ONE OF THE CONVEYORS. HE WAS USING A RETRACTABLE BLADE KNIFE WITH A NE W BLADE TO DO THE CUTTING.THE BLADE CUT THE BELTING EASIER THAN EXPECTED AND HIS LEFT HAND WAS UNDER THE BELTING SUPPORTING IT. THE BLADE SLICED TWO OF THE LEFT HAND FINGERS.

THE EE WAS GETTING OUT OF THE CAB OF LOADER WITHTHE INTENT TO HAVE A CONFERENCE WITH ANOTHER DRIVER. THE CAB HAS A PANEL BELOW THE DOOR WHICH THE OPERATOR MUST STEP OVER(APPROX 12 IN) TO EXIT THE CAB TO THE CATWALK. THE EE TRIPPED OVER THISPANEL AND HIS RIGHT KNEE CAME DOWN ON THE CORNEROF THE CATWALK IN FRONT OF THE ACCESS LADDER.THEHAND RAIL KEPT HIM ON THE LOADER

EE WAS HELPING TO TIGHTEN SOME BELT LACINGS WHILE REPAIRING A CONVEYOR BELT HE WAS USING A 1/2" ELECTRIC IMPACT WRENCH WITH A LACE NUT DRIVER TOOL TO TIGHTEN THE LACING NUTS. HE WAS NOT WEARIN G SAFETY GLASSES & A PARTICLE OF STEEL CAME OFF THE NUT ON THE TOOL & LANDED IN HIS LEFT EYE.

EE WAS STANDING ON THE GROUND, GREASING THE PINS IN A 988B CAT LOADER BUCKET ASSEMBLY. A GUST OF WIND CAME UP & BLEW SOME SAND FOR THE GROUND INTO HIS FACE. ONE PARTICLE OF SAND GOT INTO HIS E YE.

EE WAS CARRYING A PIECE OF PLYWOOD OVER HIS HEAD TO AN AREA TO USE THE PLYWOOD. HE STEEP INTO SOME LOOSE GRAVEL WHICH GAVE WAY UNDER HIS FOOT CAUSING HIS ANKLE TO TURN INWARD.

WAS POUNDING IN A NAIL WHILE BUILDING SOME CABINATES, MISSED THE NAIL & HIT HIS FINGER [FELT RIGH FINGER].

EMPLOYEE WAS ATTEMPTING TO DRIVE OUT WEDGE LATS ON JAW CRUSHER BY HOLDING A DRIVING SHAFT WITH HIS LEFT HAND AND UNDER HAND SWIGNING A 16# SLEDGE HAMMER WITH THE RIGHT HAND TO IMPCT THE SHAFT AND DRIVE THE WEDGE OUT. HAMMER HEAD DEFLECTED OFF END OF DRIVING SHAFT AND THE HAMER CONTINUED TO SWING BRINING THE HANDLE OF THE HAMMEER TO IMPACT WITH CROSS SUPPORT I-BEAM. EMPLOYEES.

EMPLOYEE WAS HELPING INSTALL SPUD PADDLES ON A PRE-SCRUBBER (BLADE MILL). HE WAS USING A CROWS FOOT PRY BAR TO WEDGE BETWEEN THE PADDLE AND THE NUT ON ONEOF ITS MOUNTING BOLTS. WHILE ANOTHHE R EMPLOYEE TIGHTENED THEHEAD OF THE BOLT. A TAPERED HEAD, EE DRIVEN BOLT, THE PRY BAR SLIPPED OFF THE NUT AND THE EMPLOYEE PULLED IT'S END TOWARD HIS FACE. THE POINT OF HTE BAR PIERCED HIS R

EMP WAS CHANGING OUT A RETURN ROLLER ON A LATTUSFRAME CONVEYOR. HAD TO CRAWL UNDER THE CONVEYOR TO GET TO THE ROLLER. SPACE WAS LIMITED AND HIS HARD HAT CAME OFF WHILE CRAWLING OUT FROM UNDER THE CONVEYOR. AFTER COMPLETING THE JOB HE HIT HIS HEAD ON A PIECE OF ANGLE IRON WHICH WAS A BRACE ON THE CONVEYOR SUPORT LEG.

EMPLOYEE WAS HELPING TO ADJUST SCREEN PANELS ON A DISTER SCREEN. HE HAD ONE PANEL OUT AND THE CLAMP RAIL. IT NECESSARY TO CUT THE CLAMP RAIL WITH A TORCH AND HE HAD THE RAIL STANDING ON THE CA T WALK NEXT TO THE SCREEN PANEL WHICH WAS LEANINAGAINST THE SCREEN BOX & POUNDING ON THE END OF RAIL THAT HAD BEEN CUT TO DE-BURR IT. THE HAMMERGLANCED OFF CLAMP RAIL HITTING FINGER AGAINT SC

EE WAS HELPING ANOTHER EE AT A 50 TON HYDRAULIC PRESS. THEY WERE PRESSING THE TAIL SHAFT OUT OF ITS FLANGED HOUSING, FROM A 36" COARSE MATERIAL WASHER. WHEN THE 3" DIAMETER BY 24" SHAFT WAS FR EE OF THE HOUSING, THEY TRIED TO SLIDE THE FLANGED HOUSING OVER THE TOP OF THE SHAFT. HOUSING TIPPED OFF XBEAM FALLING APPROX. 2' ONTO EE'S FOOT.