Arcosa Brooks Plant #1682: 1 muerte registrada Metal/Non-Metal

Injured employee and another employee were opening the Kiln doors. The injured employee was opening the left door when it became hung on the burn pipe the right door continued to open and struct the injured employees right small finger.

I/E was lifting bags of cement and dumping them in a mixing sack. I/E felt back pop.

Maint. mechanic was changing drive belts on fan when finger was rolled around sheave causing cut to left middle finger requiring 12 stitches on outside of finger

Supervisor slipped on loose soil

Hitting bucket tooth adaptor with 20lb sledge hammer piece broke off struck employee and entered inside right leg exiting 4 inches below entry point

Taking a drive shaft out of a haul truck when drive shaft fell smashing left thumb between shaft and rear stabilizer.

Employee was using a 4 in grinder

Lifting heavy object

Employee was cutting belt with utility knife when he cut his left forearm.

Employee was prying rock with pry bar and bar slipped off striking employee in head. Employee was wearing hardhat....

Was cleaning and installing idlers, moved from C belt to pony motor platform. He twisted his knee on a rock on the walkway between C belt and pony motor platform. (knee strain)

Employee was installing belt drive system when an electric motor slid off its mounting bracket injuring employee's left knee and right hand.

Employee was lifting a floor jack approx. 80 lbs. Employee complained of low back pain. Transported employee to health care provider. Diagnosed with lower back strain.

Independent contractor(truck driver) suffered a fatal heart attack while tarping his trailor.

Employee was assisting maint tech changing sreens. Employee reached for a hot torch and suffered burns to his left forearm.

Employee was loading rail car. Employee released brake, then tried to reset brake. Brakes failed. Employee dismounted rail car injuring his left knee.

The injured was loading a truck using a conveyor when fine material lodged in his eye. He suffered a corneal abrasion and conjunctivitis.

Employee was operating a band saw, performing maintenance operations on a water line. Employee's hand slipped under cutting blade. Minor cut to left thumb requiring sutures.

Employee was running up set of stairs which were partially covered with snow. Employee fell to the ground and suffered a low back contusion.

EE was working on a pole mounted light. He attempted to remove a bracket holding the light in place and was shocked by 480 power.

EE was digging a large rock out of the raw crusher the rock fell jarring the bar the EE was using. The bar struck the EE's left forearm.

EMPLOYEE WAS ASSISTING IN REPAIR OF TRUNNION, WHILE REPOSITIONING HE LEANED HIS HAND ON TRUNNION COVER. THE COVER WAS OFF TO THE SIDE LEANING AGAINST BASE. EE GOT HIS LEFT PINKY MASHED BETWEEN THE COVER & BASE WHEN THE COVER SLIPPED & FELL. INJURY REQUIRED STITCHES.

Employee was assisting contractor (truck driver) with hard to operate latch on trailer tailgate, when latch let loose ee mashed right ring finger between handle and tailgate. Received fracture and 20 sutures to repair nail bed.

EE working near welder, accidentally arc flashed in eyes. EE went to doctor that evening. Received drops & ointment for flash burn.

EMPLOYEE WAS OPERATING A BACKHOE TRACTOR TO UNBRIDGE THE HANGUP IN THE FEEDER CHUTE TO THE IMPACT CRUSHER. A SMALL PIECE OF SLATE WAS EJECTED FROM THE CRUSHER HITTING THE EMPLOYEE IN THE MOUTH.

WHILE CLEANING WORK AREA-PLACED 4" STEEL PIPE PIECES ONTO FORKS OF FORK LIFT. CAUGHT FINGER OF LEFT HAND BETWEEN TWO PIECES OF PIPE.

EE REMOVING BOLTS ON CRUSHER WITH AIR POWERED RATCHET. AIR HOSE (3/4"ID) FAILED COMING LOOSE BY FITTING-CAUSING HOSE TO WHIP AROUND AND BLOW DUST INTO EE'S EYES & HITTING EE'S HEAD BY RIGHT EA R. EE WAS WEARING HARD HAT & SAFETY GLASSES WHEN HOSE FAILED-HAT & GLASSES KNOCKED OFF.

EE WAS REPAIRING A 1" WATER HOSE - CUTTING END OF HOSE WITH KNIFE, KNIFE SLIPPED CUTTING LEFT THUMB - NEEDED 8 SUTURES.

EE WALKING ALONG TRAVELWAY, MISSED FIRST STEP OF A SET OF 3 STAIR STEPS. FELL AND LANDED ON 2ND & 3RD STEP, BRUISING LOWER BACK.

EMPLOYEE TRIED TO CLOSE FRONT WINDOW OF TRACKING, STRAINED MUSCLES OF RIGHT SHOULDER WHILE REACHING UP FOR WINDOW.

EE REPLACING BEARING ON CRUSHER ROTOR (ELECTRIC LOCKED OUT), WHILE ANOTHER EE ROTATED IMPACTOR ROTOR, INJURED EE WATCHING BEARING - PLACED HAND (LEFT)BETWEEN ROTOR AND CRUSHER WALL - ROTOR HAM MER CAUGHT HAND BETWEEN ROTOR AND CRUSHER SIDE WALL.

EE ASSISTING MAINT REPLACE CONVEYOR BELT, WHILE CUTTING OFF SECTION OF OLD BELT UTILITY KNIFE SLIPPED AND CUT EE IN RIGHT THIGH - REQUIRED 2 SUTURES.

EE WAS REMOVING A GUARD, PLACED A PIECE OF THE GUARD TO THE SIDE AND WENT TO GET A TOOL. ON HIS RETURN HE HIT HIS HEAD ON THE PIECE HE JUST MOVED, LACERATING HIS FORHEAD REQUIRING 3 SUTURES.

EMPLOYEE ASSISTING MAINT REMOVE BOLT FROM MOUNTING. BOLT SLIPPED AND STRUCK EE ON RIGHT SIDE OF FACE REQUIRING 2 SUTURES TO CLOSE LACERATION.

EMPLOYEE WAS TIGHTENING ALLEN HEAD BOLTS ON ONE CRUSHER WITH T BAR, WHILE TWISTING HE FELT PULL IN MID AND LOWER BACK.

EE WAS SHOVELING SPILLED MATERIAL BACK ONTO THE CONVEYOR BELT, FELT HIS BACK MUSCLES "PULL" WHILE SHOVELING.

OPERATING HAND CRANKED RATCHET, HAND SLIPPED & SKINNED KNUCKLE ON RIGHT LITTLE FINGER. RECIEVED5 SUTURES TO CLOSE AVULSION.

EMPLOYEE WAS REPORTING A HOT STEEL SHAFT FROM A COOLER. GRABBED SHAFT WITH BARE HAND CAUSING THERMAL BURNS TO FINGERS OF RIGHT HAND.

EE USING SLEDGE & SLEDGE WRENCH TO LOOSEN/ADJUST LARGE NUT. EE MIS-HIT SLEDGE & HIT RIGHT HAND ON WRENCH & SLEDGE HANDLE.

EE CUTTING PIECE OF SKIRT RUBBER WITH LITTELITY KNIFE-KNIFE SLIPPED CUTTING EE IN LEFT THIGH REQUIRING 4 SUTURES.

EMPLOYEE, WALKING IN RAINY, MUDDY CONDITIONS, ATTEMPTED TO MOVE 5 HP PORTABLE PUMP, SLIPPED BACKWARDS AND FELL ON RIGHT ARM, FRACTURING A RIB.

EE HELPING TO MOVE PORTABLE TANK(60 GAL.)- WHEN ADJUSTING, HE PINCHED R. MIDDLE FINGER BETWEEN TANK AND LOADING TOOL. EE WAS WEARING GLOVES BUTPINCH CAUSED LACERATION TO PAD OF FINGER. CLINIC CLEANED & CLOSED W/12 SUTURES.

EE ASSISTING WELDER ARC WELD ACHORS INSIDE KILN SHELL-REFLECTED FLASHED BOUNCED INSIDE WELDER HOOD EE WAS WEARING CAUSING FLASHBURN TO EYES.

EE OPERATING F/E LOADER TO CLEAN OUT MATERIALS ON RAMP, EE PUSHED DECLUTCH INSTEAD OF BRAKE JOLTED HIMSELF CAUSING BACK PAIN. TAKEN TO CLINIC 8-1-01 800 AM OBSERVATION ONLY. FOLLOW UP VISIT 8- 6-01-CLINIC ORDERED PHYS. THERAPY WITH LIGHT DUTY RESTRICTIONS. PS OPERATOR WAS WEARING SEAT BELT.

EE SHOVELING BELT SPILLAGE FROM UNDER STOPPED BELT, GOT RIGHT HAND TOO CLOSE TO ANGLE BRACING & GOUGED A 1/2" X 1/2" X 3/16" PIECE OUT OF HIS MIDDLE FINGER, WAS NOT WEARING GLOVES. RECEIVED 5 SUTURES AT CLINIC.

EE ON ONE KNEE, PUSHING A 100 TEN HYD. JACK INTO POSITION, WHILE PUSHING FELT PAIN IN UPPER BACK.

EE SHOVELING SPILLED MATERIAL, COMPLAINED OF PAIN IN RIGHT ELBOW AND SHOULDER.

EE WAS WALKING UP INCLINED WALKWAY & FELT MUSCLEIN RIGHT CALF STRAIN (MUSCLE PULL).

EE WAS HOLDING PIECE OF CHUTE THAT A WELDER WAS TACK WELDING, INADVERTANTLY RECEIVED WELDING FLASH.

CONTRACTOR WAS WORKING WITH ASSOCIATE ON OPERATINGY STATIONARY HOIST. ASSOCIATE HAD BOX WITH CONTROLS AND WAS GETTING OUT OF HIS REACH. HE SWUNG THE BOX WITH CONTROLS WITCH WAS ON A CABLE TO H IS PARTNER, PARTNER MISSED AND BOX HIT HIS CHIN.

PERFORMING REPAIRS TO CONVEYOR BELT, STEPPED OFFBELT TO DECK (18"DROP) TWISTED ANKLE

ONE COMPANY MAINTENANCE MAN AND TWO CONTRACTOR ELECTRICIANS WERE WORKING AT A 600 AMPS DISCONNECT BOX WHEN AN EXPLOSION INSIDE THE BOX BURNED ALL THREE PEOPLE. THE COMPANY EE RECEIVED 2ND & 3R D DEGREE BURNS ON HIS ARMS, TORSO & LEGS. ONE CONTRACTOR RECEIVED 2ND & 3RD DEGREE BURNS OVER 45% OF HIS BODY & THE OTHER CONTRACTOR RECEIVED 2ND OR 3RD DEGREE BURNS ON ONE HAND.

ONE COMPANY MAINTENANCE MAN & TWO CONTRACTOR ELECTRICIANS WERE WORKING AT A 600 AMPS DISCONNECT BOX WHEN AN EXPLOSION INSIDE THE BOX BURNED ALL THREE PEOPLE. THE COMPANY EE RECEIVED 2ND & 3RD DEGREE BURNS ON HIS ARMS, TORSO, & LEGS. ONE CONTRACTOR RECEIVED 2ND & 3RD DEGREE BURNS OVER 45% OF HIS BODY & THE OTHER CONTRACTOR RECEIVED 2ND & 3RD DEGREE BURNS ON ONE HAND.

ONE COMPANY MAINTENANCE MAN & TWO CONTRACTOR ELECTRICIANS WERE WORKING AT A 600 AMPS DISCONNECT BOX WHEN AN EXPLOSION INSIDE THE BOX BURNED ALL THREE PEOPLE. THE COMPANY EE RECEIVED 2ND & 3RD DEGREE BURNS ON HIS ARMS, TORSO, & LEGS. ONE CONTRACTOR RECEIVED 2ND & 3RD DEGREE BURNS OVER 45% OF HIS BODY & THE OTHER CONTRACTOR RECEIVED 2ND & 3RD DEGREE BURNS ON ONE HAND.

EMP WAS COVERING A STOCK PILE WITH A TARP. HE TOSSED A CAR TIRE ON THE STOCK PILE TO HOLD DOWN THE TARP. PULLED A MUSCLE IN LOWER BACK. RECEIVED TREATMENT ON 5-16-97.

WALKING IN YARD AND TWISTED HIS KNEE ON A UNEVEN SURFACE.

EE WAS MOVING A PIECE OF CATWALK GRATING DOWN INTO A TUNNEL WHEN HE LOST CONTROL OF PIECE HE WAS MOVING WHICH IN TURN PULLED HIS BACK MUSCLES.

EE BANGED LEFT KNEE OR CATWALK GRATING WHILE ENTERING DUCT FOR INSPECTION. RESTRICTED DUTY NO PROLONGED WALKING OR STADNING FOLLOW UP VISIT TO DR 3-4-96.

STEAM GINNY HOSE HAD A HOLE IN IT. EE STOOD ON HOSE TRYING TO STOP LEAK. THE HOT WATER PENITRATED HIS BOOT & BURNT HIS FOOT.

EE LOST HIS BALANCE DUE TO A PIECE OF DUST IN HIS EYE HE TURNED HIS RIGHT KNEE

EE WAS CLMBING UP STATIONARY LADDER AT REAR OF #3 KILN, STRUCK HEAD (WITH HARD HAT ON) ON THE GUARD AROUND STEPS CAUSING HEAD TO JAM INTO NECK AND SHOULDER AND SUFFERED PAIN IN THAT SAME AREA (RIGHT SIDE OF NECK AND SHOULDER). EE FELL TO GROUND AND WAS MOMENTARILY DAZED.

EE WAS WORKING ON THE NONHAZARDOUS PAD BY A TANKER TRAILER. HE LEANED OVER TO PICK UP A OFFLOAD HOSE AND HIS HARD HAT FELL OFF. WHEN HE RAISED HIS HEAD, HE HIT THE END OF THE TRAILER. HE RECEI VED 10 SUTURES ON THE SCALP.

THE INJURED EMPLOYEE WAS WALKING IN THE KILN, STEPPED INTO A LOW SPOT IN THE LINING, AND TWISTED HIS BACK.

EE SLIPPED WHILE WALKING FROM THE CAB OF THE TRUCK, ACROSS THE HOOD TO ADJUST THE PASSENGER SIDE MIRROR. HE FELL, WITH HIS BACK LANDING ACROSS THE HOOD. HIS BOOTS WERE MUDDY, THE HOOD WAS SLIC K FROM RAIN, AND HE SHOULD HAVE NEVER BEEN WALKING ACROSS THE HOOD OF THE TRUCK. THE DESIGNATED WALKWAY GOES FROM THE CAB AROUND THE HOOD, AND HAS FALL PROTECTION IN PLACE.

THE INJURED EMPLOYEE WAS USING TWO CRESCENT WRENCHES TO BREAK THE BOLTS, LOOSE ON FLANGED PIPE CONNECTION. ONE OF THE WRENCHES SLIPPED OFFCAUSING TO LOOSE HIS BALANCE. HE FELL STRIKING HIS R ELBOW AGAINST THE STEEL PIPE. HE REPORTED IT THAT MORNING, BUT DECIDED TO GO TO THE DR. ONLY AFTER THE SWELLING GOT WORSE.

THE INJURED EMPLOYEE WAS USING A WELDER AND CUTTING RODS TO CUT REFRACTORY ANCHORS OFF THE SHELLOF THE KILN. THE ANCHOR HE WAS GOING TO CUT WAS AT THE 1 O CLOCK POSITION. HE POSITIONED HIS ROD WITH THE SHIELD UP THEN IN ONE MOTION FLIPPED HIS WELDING SHIELD DOWN OVER HIS FACE AND MOVED THE ROD TO CONTACT WITH THE METAL. THE SHIELD DIDN'T FLIP ALL THE WAY DOWN LEAVING HIS FACE

INJURED EE WAS STANDING ON THE GROUND, LEANING OVER A CATWALK, AND REACHING ONTO A KILN PIER TO RETRIEVE SEVERAL PIECES OF STEEL. THE CATWALK IS ROUGHLY 44" OFF THE GROUND, 36" WID, AND 16' BE LOW THE TOP OF THE PIER. THE STEEL WAS 3/8" THICK. THE PIECES SLID OFF THE PIER ONT THE CATWALK, WHERE THE CORNER OF ONE PUNCTURED THE CENTER OF CARB. CLEANER THAT WAS LEFT THERE. SPRAY IN FA

INJURED EE WAS CLIMBING DOWN OUT OF THE CAB OF THE LOADER. AS HE WAS CLIMBING DOWN THE STEPS, HIS FOOT SLIPPED OFF ONE AND LANDEDON THE NEXT STEP DOWN. HIS HANDS NEVER RELEASED THE HANDRAILS. THE JAR FROM FALL JUST FROM ONE STEP TO THE NEXT STRAINED HIS LOWER BACK.

EE WAS LIGHTING A KEROSENE SPACE HEATER. THE KEROSENE HAD GASOLINE MIXED INT WITH IT DUE TO A SUPPLIER ERROR. WHEN HE LIT THE HEATER, A FIREBALL FROM THE FUEL BURNED HIS FACE. THE SUPPLIER TES TED THE FUEL, FOUND IT TO CONTAIN GASOLINE, AND SHIPPED THE FUEL OFFSITE. THE REPORT IS LATE DUE TO THE TIME IT TOOK TO TEST.

THE INJURED PERSON AND THE WITNESS WERE LIFTING A 25 HP ELECTRIC MOTOR OFF A STAND. THEY WERE USING A BAR THRU THE EYEBOLT ATTACHED TO THE TOP OF THE MOTOR AS A MEANS TO GRIP AND LIFT. THE MOT OR WHEN THEY GOT THE MOTOR OFF THE STAND THE EYEBOLT BROKE. THE JERK FROM THE EYEBOLT BREAKING JERKED THE INJURED MAN S BACK, CAUSING THE INJURY.

INJURED WAS USING APICK ON A RING IN #3 KILN. A PIECE OF THE RING FELL HITTING HIM IN THE SHOULDER AREA HE THEN TWISTED HIS KNEE. AND ANKLE ALSO HAD ABRASIONS TO RIGHT WRIST.

LADDER WAS NOT BOXED IN. EMPLOYEE SLIPPED WHILE CLIMBING DOWN LADDER AND FELL TO CAT WALK. CALLED DAVID RICHMOND 9/1/94, 11:30 A.M. TO REPORT OCCURRENCE. 606 276 1384

#7 CONVEYOR BELT HAD TRACKED OVER AGAINST THE FRAME AT THE LOWER BALANCE DUE TO MUD CAKED ON CONTER BALANCE PULLIES IN WAS EFFORT TO SCRAPE THE MUD OFF SO THE BELT WOULD TRACK WE USED A SCRAPE R BAR TO PULL THE MUD OFF THE BAR DID NOT HAVE ALARGE ENOUGH HANDLE TO PROVIDE ADEQUATE LEVERAGE IT WAS CAUGHT BY THE COUNTER BALANCE PULLEY & PULLED IN ALONG WITH MY HAND

I WAS ON TOP OF WATER TRUCK HAD SOME MUD ON FEET I SLIPPED OFF THE TOP OF WATER TRUCK ABOUT 10 TH FROM GROUND AND FELL INTO A PIT. HITTING WITH MY TABLE WEIGHT ON KNEES. RIGHT AFTER A LARGE KN OTT APPEARED ON THE BACK OF MY LEG JUST BEHIND THE RIGHT KNEE.

STRAIN LIFTING WATER PUMP.

EE WAS STANDING ON A LADDER (A) 5 RUNGS UP WHEN HE STOP DOWN ON A RUNG HE PULLED HIS GROIN IN BACK (LOWER) WAS SEEN BY A DOC ON 11--8-93

EMPLOYEE WAS WALKING DOWN RAW CRUSHER STEPS CARRYING A BUCKET. THE THIRD STEP FROM BOTTOM BROKE HE GRABBED THE HAND RAIL AND TWISTD HIS BACK MUSCLE. HE SAID IT WAS JUST SORE AND CONTINUED TO W ORK. HE WENT FOR MEDICAL TREETMENT ON 3-26-93.

WHILE REMOVING INSPECTION PLATE FROM COAL MILL EXHAUSTER EMPLOYEE LOST FOOTING & PLATE FELL ON RIGHT FOOT.

EMPLOYEE FIRST INJURED LEFT THUMB ON A STAIRWAY WHEEL OF THE #10 MACK HAUL UNIT ON SUPT 1 1992 NO FIRST AID OR MEDICAL TREATMENT WAS REQUIRED ON 10-09-92 HE ROTA TURNED HIS LEFT THUMB ON THE R AW CRUSHER CONTROL ROOM DOOR HE JAMMED HIS LEFT THUMB ON THE SIDE OF THE DOOR HE RECEIVED A INJECTION OF CORRISTON FOR TENOSYNOVITIS OF LEFT THUMB

LIFTING TWISTING WHILE CARRHING 5 GAL BUCKET IN SIDE STRAINED LOWER BACK

EMPLOYEE STARTED WORK AT 7 AM HE WENT TO HIS HAUL UNIT, GOT IN, STARTED THE UNIT. WITHOUT MAKING A PRE-SHIFT SAFETY INSPECTION WHICH IS REQUIRED BY ALL EQUIPMENT OPERATOR'S HE TOOK OFF IN THE HAUL UNIT. THE BED OF THE UNIT WAS IN THE RAISED POSITION AND HE DID NTO NOTICE IT. AFTER RUNNING THE UNIT APPROX 100' THE BED CAME INTO CONTACT WITH POWER LINES. FUSES BLEW BACK TO THE MAI

EE WAS USING A SHOVEL (HAND) TO REMOVE FINE SHALE FROM AROUND A TAIL PULLEY, WHILE SHOVELING, HE STRAINED HIS LOWER BACK.

EMPL USING COME-ALONG TO SUPPORT A DIFFERENTIAL GEAR -100 LBS-WHILE TRYING TO PLACE GEAR IN HOUSING,THE COME-ALONG SLIPPED ,GEAR FELL 24" ON EMPL LEFT HAND.HAD A CONTUSION OF LEFT HAND.

EMPLOYEE WAS COMING DOWN A STATIONARY MAN LADDER. HE LOST HIS FOOTING AND FELL FROM APPROX. 7'. HE LANDED ON HIS RIGHT SIDE. ALL X-RAYS NEGATIVE. EMPLOYEE IS BRUISED AND SORE. HE WAS PLACED ON LIGHT DUTY. THERE WAS NO LOST TIME INVOLVED.

WORKING INSIDE DUST BOX AT BACK OF ROTARY KILN.HAD PLACED A 2 X 10 BOARD ACROSS THE BOX TO STAND AND WORK OFF OF.ONE END OF THE BOARD SLIPPED AND EMPL FELL ONTO RIGHT SIDE.FELL 3-4'.ANOTHER MA N WAS WORKING WITH HIM SLID DOWN ON TOP OF HIM.

EMPLOYEE WAS LAYING BLOCK IN A ROTARY KILN.HE PICKED UP A BLOCK AND HANDED IT TO ANOTHER EMPLOYEE.WHEN HE DID,HE STATED THAT HE FELT A STIFFNESS IN HIS LOWER BACK.

EE WAS SHOVELING LOOSE MATERIAL INTO A WHEELBARROW AND THEN MOVING MATERIAL VIA WHEEL BARROW TO ANOTHER LOCATION. HE BUMPED INTO A 4 INCH FLEXIBLE HOSE AND CUT ARM ON A HOSE CLAMP.

GETTING READY TO ROLL HOSE GRABBED HOSE WITH HANDS TWISTED MOTION WITH TORSO PAIN IN LOWER BACK

EMPLOYEE WAS MOVING A PALLET OF FIRE BRICK USING A PALLET JACK HE PULLED ON JACK & HE FELT A PAIN IN HIS RT SHOULDER HE WAS TAKEN TO THE DOC & WAS DIAGNOSED AS HAVING A MUSCLE PULL IN HIS RT S HOULDER EMPLOYEE PLACED ON LIGHT DUTY 02-25-91

HOOKING BOO M TO FRONT END LOADER TRIED TO PUSH IT IN PLACE BY HAND END OF BOOM DROPPED HITTING HIM IN L ANKLE

WORKING IN #3 KILN USING A JACKHAMMER WHEN IT SLIPPED AND EMPLOYEE PINCHED THE LITTLE FINGER ON THE LEFT HAND BETWEEN THE HAMMER AND THE KILN SHELL MAKING A CONTUSION ON THE FINGER.

EMPLOYEE WAS LIFTING A BATTERY CHARGER APPROX 40LBS UP ONT O A NORTHWEST 180D SHOVEL WHEN HE RAISED THE CHARGER UP OVERHEAD HE FELT A PAIN IN HIS BACK

EMPL WALKING DOWN STEPS -HUNG FOOT IN A STEP AND STUMBLED.THERE WAS NOTHING ON STEP AND IT WAS IN GOOD CONDITION.

EMPLOYEE TRIPPED AND FELL AND OVER A FAN SHAFT.

EMPL WAS WALKING ACROSS KILN DECK WHEN WIND BLEW SMALL PARTICLE OF DIRT INTO LEFT EYE.

EMPLOYEE WAS WORKING ON EXHAUST SYSTEM OF A TRUCK A PIECE OF RUST FELL INTO HIS EYE HE WASHED OUT HIS EYE & THOUGHT HE GOT THE PIECE OUT THE NEXT MORNING HE WAS STILL HAVING PROBLEM THIS IS WH EN HE REPORTED THE ACCIDENT I TOOK HIM TO THE DOC.& HE USED A NEEDLE TO REMOVE PIECE OF RUST FROM THE EYE(MSHA REPORTABLE)

EE WAS BENT OVER REMOVING BRICK FROM BOTTOM OF ROTARY KILN. A PIECE OF CASTABLE CAME LOOSE FROM SIDE WALL STRIKING HIM IN THE SMALL OF HIS BACK.

EMPL SLIPPED RETURNING FROM CLEAN AN CLOGGED CHUTE.

TRIPPED AND LANDED ON RIGHT SHIN BONE.

WALKING DOWN STEPS,CAUGHT FOOT ON LAST STEP TWISTED RIGHT KNEE.

EMPLOYEE WAS USING A PRY BAR TO PUNCH OUT A CHUTE THAT WAS STOPPED UP.IT WAS RAINING AND HIS AHND SLIPPED OFF OF BAR.THE BAR STRUCK HIM ON THE LOWER PART OF HIS LEFT ARM JUST ABOVE WRIST.

EMPL WAS INSTALLING MOTOR ON CEDAR RAPIDS JAW CRUSHER. HE WAS IN FULL SQUAT POSITION JOCKEYING MOTOR INTO POSITION. WHEN HE STOOD UPRIGHT LEG WAS APPARENTLY NOT IN PROPER POSITION WHICH CAUSED UNDUE STREE TO KNEE JOINT. INJURY WAS NOT IN ANWAY RELATED TO LACK OF COMPLIANCE TO ANY RULES OR REGULATIONS NOR WAS IT CAUSED BY INADEQUATE TRAINING JOB SKILLS OR LACK OF USE OF PROTECTIVE E

EMPLOYEE WAS WALKING DOWN THE CATWALK ON OUR #5 CONVEYOR AND HE SLIPPED AND FELL. THE EMPLOYEE FELL ON HIS LEFT SIDE AND HURT HIS LOWER BACK AND HIP AREA. NOT SURE OF INJURY UNTIL 2-13-89 WHEN SURGERY REQUESTED. RESULT WAS LUMBAR DISC DISPLACEMENT.

EMPL HELPING RE4OVE OLD BRICK FROM 11' X 175' X KILN BRICK FELL FROM ABOUT 7' HIT EMPL ON RIGHT THUMB.

EMP WAS PREPARI3G A PYCROMETER TO DETERMINE SPECIFIC GRAVITY OF SOLITE AND WHILE DRYING THE OUTSIDE OF THE PYCROMETER WITH A TOWEL, HE DROPPED IT ON THE COUNTER WHERE IT SHATTERED CAUSING LACE TIONS TO HIS R 2AND R FINGER

EMPLOYEE WAS HE5PING TO INSTALL TOOTH ON SHOVEL BUCKET EMPLOYEE WAS USING SLEDGE HAMMER TO LOOSEN TOOTH PC OF METAL BROKE OFF TOOTH HITTING EMPLOYEE IN LEFT ARM.

EMPL CLEANING C2UTE WITH METAL BAR HIT MIDDLE FINGER AGAINST I-BEAM.HURT FINGER FIRST AID ONLY ACTION TAKEN UNTIL 4-10 WHEN FINGER WAS OPERATED ON.

EMPLOYEE WAS CL9ANING UNDER AND AROUND #10 CONVEYOR AND TAIL PULLEY HE WAS USING A LONG HANDLED SHOVEL TO CLEAN WET MATERIAL FROM AROUND REAR OF TAIL PULLEY HE LOST HIS BALANCE AND FELL WHILE FALLING HE REA7HED FOR SMALL BOX ON REAR OF CHUTE TO CATCH HIMSELF AND MISSED TRAPPING HIS ARM UNDER THE CHUTE ASSEMBLY

EMPLOYEE REMOVE8 WELDING HOOD FROM HEAD AND METAL OBJECT BLEW INTO HIS RT EYE DR REMOVED RUST PARTICLE FROM EYE NO TIME LOST

EMP WAS HELPING TO MOVE STAINLESS METAL INSIDE THE DUCON, HE WAS HOLDING IT UNDER HIS ARM AND WHEN IT WAS PULLED FROM HIS ARM IT CUT HIS LEFT UPPER INSIDE ARM ABOVE THE ELBOW

HAMMER SLIPPED 0ROM HAND CAUSING EMPLOYEES ELBOW TO STRIKE A STAINLESS STEEL STANCHION BRUISING HIS ELBOW DR DRAINED EXCESS FLUID FROM AREA

WIRE BRUSH MOUNTED TO HAND GRINDER SLIPPED FROM OPERATORS HAND ABRADING HIS LEFT FOREARM ABRASION RESULTED IN SKIN INFECTION CLOSE QUARTERS CONTRUBUTED TO INJURY

EMPLOYEE DUMPED3CASTABLE FROM ELECTRIC CONCRETE MIXER CAUGHT THUMB BETWEEN MIXER BARREL AND FRAME OF MIXER

EMPLOYEE WAS CLIMBING UP ON A TRUCK TO SHUT ENGINE OFF HIS FOOT SLIPPED OFF OF THE STEP & HE FELL HITTING THE FRONT BUMPER THE EMPLOYEE STRAINED HIS BACK WHEN HE FELL

EMPLOYEE WAS HELPING TO LIFT A SECTION OF A NEW CONVEYOR WHEN EMPLOYEE STRAINED HIS BACK.