Avísenme cuando se presente un nuevo incidente de la MSHA en Band Mill 2.
| Trimestre | Horas trabajadas | Citaciones | S&S | Por 1M hrs |
|---|---|---|---|---|
| 2013 Q4 | 0 | 0 | 0 | |
| 2013 Q2 | 2,360 | 3 | 0 | 1271.2 |
| 2013 Q1 | 0 | 9 | 3 | |
| 2012 Q4 | 2,707 | 29 | 7 | 10713.0 |
| 2012 Q3 | 0 | 40 | 5 | |
| 2012 Q2 | 0 | 9 | 2 | |
| 2012 Q1 | 0 | 17 | 4 | |
| 2011 Q3 | 590 | 21 | 4 | 35593.2 |
Employee was handling belt rollers when his shoulder started to hurt, employee had strained shoulder 3/4/13 but had not seeked medical attention. Employee was taken off of work effective 4/23/2013.
Employee was using a ladder to install an antenna on a pole when he fell twisting his right ankle resulting in a chip in his bone.
Employee slipped twisting his knee, he continued to work until 05/02/2011 at which time he began loosing time.
Employee was lifting a miner cable when he strained his back. The employee continued to work until May 23, 2011 at which time he was removed from work by his physician. This accident has been under investigation and has now been determined (June 17, 2011)to be work related and reportable.
A roof fall occurred in the #5 entry between crosscuts 86 and 87 in the mine's intake entry. The fall was above the roof bolt anchorage and measured approximately 100 feet in length.
Employee was struck in neck with a chip from pin as the track pin was being driven in with a hammer. Bleeding was stopped in less than 1 minute. He was transported to hospital for further exam. He was airlifted to U.K. for precautionary examination.
Employee was tramming the roof bolter out of the # 4 entry, when the roof bolter cable stuck, causing the cable to be jerked down. The cable hook struck the operator/employee on his left cheek, resulting in a laceration that required 5 stitches to close.
Employee was holding a pipe wrench attempting to loosen a pipe fitting when a fellow employee struck the handle of the wrench with a hammer. The hammer struck the employee on his small finger on his left hand resulting in a fracture.
Employee, was removing the insulation on an electrical cable using a utility knife in preparation to make a cable splice. During the process he accidentally cut his left hand. The laceration required 10 stitches to close.
Employee was operating a rubber tired personnel vehicle when the front tire hit a hole in the road causing the steering wheel to spin around striking the back of his hand. This resulted in a small fracture to one of the bones in his hand.
Employee has contracted pneumoconiosis (Black Lung) and is a Part 90 Miner.
Employee was operating a continuous miner performing retreat mining, when a portion of the coal rib came loose and struck him on the back, knocking him down. He continued to work until 05/26/09 at which time he stopped due to the ongoing pain in his neck.
Employee was lifting a piece of belt structure when he felt a pain in his stomach. He continued to work until 3/25/09 at which time he had surgery to repair a hernia in his stomach. He started losing time after his surgery.
Employee was loading rock dust into a duster. He was bending over and lifting the rock dust bags from the mine floor. He experienced pain in his lower back. He continued to work until May 19th. At this time he started to miss work.
EE was changing button belt rollers. EE used a come a along to pull up the belt, but had to install the button roller by lifting them and pushing them into place. EE was working in a stopped ot bending position.
Employee was walking in an area that was 5 breaks outby. The face when he slipped and twisted his ankle. Left. On 8/20/07 He went to the dr and was diagnoised with a hairline fracture of the left fibula approx. 3" above the ankle. Accident became reportable on 8/20/07.
Employee stated that he was pulling on a cable when he felt "something give" in his right knee. Mine floor was wet and muddy. He had been diagnosed with a torn ligament in the right knee.
Employee stated he was walking in the #3 Entry at 25 x-cut when he stepped on something in the mud. He stated he felt his knee twist. He continued working the rest of his shift.
A roof fall occurred on the Franks Creek Mains. The fall was at break #72 and #6 entry, 1 break outby spad no. 13593. The fall was 4.5' thick, 8' wide & 25' long. The fall was located in a neutral airway. Fall was cribbed off and extra cribs were installed in surrounding area.
Employees was changing tires on the RD 800 Mack. EE was putting the inside tire back on truck when his middle finger on his left hand was pinched between the tire & spoke of the truck. He was taken to Norton ER stitched the end back on going to give a week to heal may have to take off first knuckel.
Employee hit a drill chuck with a wrench to insert it into the drill pot. A piece of metal came off the chuck and entered his lower right leg. He was treated in the E.R. and returned for the next two shifts of work. On Aug 3rd he returned to hospital where a Dr located and removed the piece of metal but in process damaged an artery.
ROOF CONDITIONS WERE CHANGING & STRAPS WERE USED. AS BOLTS WERE BEING INSTALLED A PIECE OF ROCK FELL & STRUCK THE EMPLOYEE ON THE LOWER PART OF HIS RIGHT LEG. X-RAYS INDICATED A FRACTURE OF THE RT. FIBULA.
ROOF CONDITIONS WERE CHANGING AND STRAPS WERE STARTING TO BE INSTALLED. AS THE SECOND BOLT WAS BEING INSTALLED IN THE STRAP, A PIECE OF ROCK FELL AND STRUCK THE EMPLOYEE ON THE FOOT. X-RAY DID NOT SHOW A FRACTURE; HOWEVER, AN MRI GIVEN ON 5/27/05 SHOWED A HAIRLINE FRACTURE.