Avísenme cuando se presente un nuevo incidente de la MSHA en Bayer Alumina Plant.
A crew of 5 workers were installing an 8'x10' process door when the lifting lug on the door became detached. This resulted in the door free falling approximately 22" to the ground and ultimately falling over onto one of the crew members.
Employee was crossing over a 36" pipe in a sitting position and became unbalanced and fell to ground level. Employee experienced pain in left forearm and was treated by Doctor. Treatment include applying a sling to the arm and prescription pain medication.
Contracted service employee (seasonal) was performing landscape maintenance/mowing on site and was stung by bee/yellow jacket. Reporting under our Mine ID as contractor is an independent contractor and does not meet the requirements to have their own mine ID under 30CFR Part 50. However, the reportable should not count against 4100320 as the person is not employed by Alcoa.
Employee says that yesterday, 6/11/2018 around 9am, right leg began to hurt just below the knee and on the outside part of the calf. Employee says doesn't know the exact time the pain started and isn't sure on exactly what cause it. Employee says the pain feels like a constant Charlie horse and is having difficulty walking on the leg.
Employee was operating machinery walking along side via remote when EE noticed something in EE's eye. Eye protection was being worn at the time. Employee reported to security for evaluation and was taken to medical clinic for further evaluation. Employee had an abrasion on the eye and was treated with medication.
Employee was moving a heavy plate (spacer) used to open a door. The employee felt pain when they lifted the plate with right hand but pain dissipated and completed shift. The following morning they reported pain in the hand/wrist.
Index finger bent backwards while pulling cable off when cable suddenly started going the opposite direction due to cable on tugger was wedged in a spot and started backspooling. Employee went to Doctor on 7/25 and was put on restrictions starting 7/26.
Red line case. On 2/16/2017 employee got in and out of the bucket of the HV bucket truck 5-6 times. Employee did not feel bad at that time but reported the injury on 2/22 after knee got worse.
Employee was scoping a job in a manlift. Employee was reaching out and up to simulate what needed to be done (not lifting anything) when EE felt pain in back. The pain did not continue and EE completed the job. After leaving work and over the weekend the pain progressed and reported pain when arrived to work on Monday 2/13.
Redline case- On 9/15/2016 employee was pouring a coup of coffee, set cup down was holding coffee pot in right hand, felt sharp pain in right wrist and dropped coffee pot. No injury resulted from the incident. On 9/23/2016 employee was diagnosed with carpal tunnel.
Elbow pain after jackhammering and sledge hammering on plugged line.
10 dB shift w/ 25 dB loss both ears
10 dB hearing shift with 25dB loss
10 dB shift with 25 dB loss bilaterally.
10dB hearing shift with 25dB loss average
Employee was opening a valve with sledgehammer in a congested work area, felt a "burning sensation" discomfort in left shoulder.
Heat rash to bilateral under arm areas. Initially employee felt was a chemical burn from using clean up hose
Changing the end on chisel gun, knelt down to break fitting loose and felt pull in left low abdomen
10dB hearing shift with 25 dB loss left ear
Hearing loss, 10 dB shift with 25dB loss
10 dB hearing shift with 25dB loss
Was holding a loading spout while coworker unbolted clamps, when last clamp came off the tube fell telescoping into itself crushing 5th digit on left hand
Cleaning a screen box on tray 16, when inserting box finger was smashed between insert and box
While attempting to loosen the nut the pneumatic wrench caused the straight wrench to turn pinching the employees hand between the straight wrench and the adjacent bypass valve. The injured cleaner received a contusion to the top of the hand.
Was cleaning screen box and hit thumb with hammer
Was using a jackhammer, stopped using jackhammer and started shoveling and felt pain in low back
EE was squatting to replace a grating, stood to pick up the grating and felt severe pain to low abdomen/right groin area
Employee was coming down a ladder, when stepping off ladder felt right knee "give out".
EE was grinding tacs off of the north elevator door, the grinder jumped and caught the glove and pulled thumb between guard and grinding disc causing laceration to left thumbnail.
Employee was hammering overhead to break loose a knocker, felt a "pinch" in employee's back.
Was walking around a pump, stepped on scale debris in ground and fell striking right hip and low back on curb
ee was walking down walkway and pant leg of Tyvek suit got caught on a piece of angle iron causing EE to fall and received a 1 inch laceration to left knee
ee was repacking a pump, the packing gland was stuck under the shaft he applied pressure to pull it out and felt right wrist pop and pain to right wrist
employee was welding on his knees, felt stinging on his knees and discovered that he was kneeling in caustic residue, minimal burn to left knee, 2nd degree burn to right knee
packing was leaking on valve, caustic sprayed out in face and ran down goggles and into left eye causing chemical burn
Tightening a stud on right side of pump, wrench slipped and injured worker struck top of tank with right elbow.
employee was sprayed in the face by chemical causing chemical burns to cheeks and lips
RED LINE CASE - became recordable on 11/23/15 when restrictions were placed, employee was working in shop welding pipe, he reached down to roll pipe on ground to apply wrap and he felt tightness to right elbow
EE was swinging a 4 lb hammer and missed nut striking index finger on left hand causing fracture and laceration.
Employee states that he was beating on multiple press feed valves and repeatedly tried to seat valves as daily routine, pain in elbow started 6 months ago.
Employee was picking up a hose and felt sharp pain in mid low back.
employee was draining a heater, hit knocker valve with hammer, right index finger was trapped between hammer and T-handle causing laceration and fracture of right index finger.
EE was putting #15 caustic on, cleared the plug free from coat line, went to verify caustic line was fully open, the caustic blew past the head gasket, he turned to run and the first step he felt a pull in right calf.
ee was opening a valve stem, was turning handle and cut his hand on sharp piece of metal causing laceration to 5th digit right hand
EE was pulling a 6 foot rolling stand, EE fell and stand fell onto low abdomen. has pain to tailbone.
RED LINE CASE unsure of work relatedness, investigation continues employee claims hernia, no specific date of occurrence, states happened in 2014 but did not file injury with Medical department. He did come to medical but it is documented the he wished to speak with union prior to reporting, Employee did not return to file injury report
RED LINE CASE employee states that he had injury about 8-10 years ago involving left shoulder, states that he is having increased difficulty with left shoulder, increased pain and difficulty with movements of arm no complaints of new injury or specific instance or action caused current pain.
Came to work early, was struck by a car in the parking lot.
Employee was utilizing the flex lance and he thought that he felt the flex lance build up of pressure in the tube and it pushed the flex lance upward. Water sprayed on his face shield and his face shield fogged, which caused him to temporarily be unable to see. He then felt water pressure hit his right foot.
ee reported pain in left hand after using impact wrench
Cut right upper thigh with utility knife when cutting strap off bundle of hose.
employee was in front of press, tripped and fell, abrasion to right arm and left knee pain
employee was closing a discharge wheel valve, felt extreme pain in both shoulders
employee was closing a valve with 8 lb hammer, finger was smashed finger between hammer and valve
Employee was closing a valve, pipe wrench pinched finger between valve and circulation line.
10 dB shift with 25 avg loss right ear
Lifted up a cover for a pump and felt pain in left shoulder.
Employee pinched finger between railing and pipework. Per email from reporting party, EE was changing out the bag on the number 3 zimpro using a pipe wrench to hold bag up, while coworker, (new to job) started loosening the fitting. Injured EE's finger was caught between handrail and pipe wrench.
Employee was tightening valve packing, wrench slipped off nut and crushed finger between valve and wrench causing a tuft fracture 4th digit left hand.
10 dB shift with 25dB avg left ear
Employee was closing a discharge valve, he felt a pull in low back.
Employee was caustic cleaning with a pry bay to remove scale, goggles became fogged, took goggles off to wipe them off, was wearing safety glasses and pry bar fell into trench , and caustic splattere under safety glasses causing burn to left eye
We had to move the old valves to the other side where the crane could fly them out. During the process of moving the old valve over the new one, it got caught. Two people let go but the third person didn't. The valve shifted in direction of the heater and pinched his hand.
Employee dropped 4 lb hammer on top of left foot causing pain.
Employee was trying to loosen a wing nut with a prybar, prybar slipped and hit finger causing bruise under nail. RED LINE CASE Case did not become recordable until 8/14/15 when prescription medication was given
Employee was standing at work station in Machine Shop and felt something in his right eye, corneal abrasion seen, no foreign object seen, eye drops prescription given
RED LINE CASE Employee states that he started having cramping at 230 and at 530 felt worsening cramps and nausea, at 745 reported illness.
RED LINE CASE, QUESTIONABLE INCIDENT, UNDER REVIEW employee was coming down ladder, misplaced foot and missed bottom rung, grabbed ladder and felt pain in low back
Employee was hooking up a barge at R52 loading dock, the barge shifted due to wind. He was attempting to board the barge and the barge employee pulled him onto the barge, he felt a pull in his left shoulder.
RED LINE CASE BECAME RECORDABLE ON 6/17/15 CASE UNDER REVIEW employee was opening a valve and struck 5th digit right hand with sledgehammer, unsure how it happened, 1 week later presented with increased pain and swelling after weekend off, xray revealed tuft fracture
employee was running an impact tool, the impact slipped off the nut, the socket hit the grating and bounced off grating and struck employee in mouth breaking 2 teeth and lacerating lip requiring sutures
10dBshift with 25dB avg loss left ear
Employee was pulling a piece of plastic pipe and the pipe slipped and crushed finger causing fracture and laceration requiring sutures.
employee was swinging sledgehammer and came in contact with T handle on valve pinching finger causing fracture and laceration to index finger left hand
employee was shoveling hydrate and 2 hours in to job he noticed stinging and burning to both feet, chemical burns to both feet
employee was pulling on packing on water ring, used the puller and it broke loose, he lost his footing and fell backward catching self on left hand to break fall, felt pain to left elbow, shoulder and left side of back
employee was changing a valve out, he was straddling pipes and when he stepped down he bumped his left knee on pipe and his knee was caught between the pipes causing contusion to the left knee
RED LINE CASE LATE REPORTING, UNSURE OF INCIDENT DATE AND TIME , WORKED FOR 1 MONTH BEFORE SEEKING MEDICAL ATTENTION states that while closing a liquor valve he missed the valve with the sledgehammer and felt pain in right shoulder
Red Line Case: Case became Medical Treatment on 5/13/15 employee was hammering and elbow hit the tank and felt pain in right elbow
Report of incident on 4/18/2015 employee was crossing over stair case, the staircase rocked causing employee to be unbalanced, he smashed his right thumb and bruised inside of right har when thumb and arm were contacted by the tools he was carrying
On Tuesday 4/14/15 at a tank roof a worker was gathering tools and stepped over a pipe with his left foot near a "rafter", he then stepped with his right leg. His left foot was still held in place by the rafter causing his left knee to twist causing discomfort.
RED LINE CASE: H&S Manager is a disputing work relatedness employee states was hitting on mud 13 valve liquor floor for about 10 minutes and in the process of hitting the valve he felt a pull in lower back
RED LINE CASE- Salaried employee- initial determination not believed to be restricted, later determined that restricted tasks were essential job functions Determined to be restricted 5/6/2015 Employee was walking in Digestion staging area verifying material for job, while walking , employee tripped over a valve and fell on to knees.
employee was closing door on screen box, tightening nuts, holding the wing nut with left hand, swung 4 lb hammer and struck left thumb
employee was closing a valve on press 8, it was getting hard to close and he felt a pop in right elbow as he was twisting the valve
10 dB with 25dB avg loss right ear
employee bent over to unload a supply box, started feeling pain in left lower back, felt spasms and tightening in back
10 dB hearing shift with 25dB avg loss right ear
RED LINE CASE. Injury date was 3/9/15 did not become restricted until 3/13/2015. Closing blow off valve, was loosening up a valve with a 8 lb hammer, felt pain in right elbow.
Employee stepped off rail car to platform and foot slipped and missed platform. Fell onto buttocks and left leg fell into open space between rail car and platform causing contusion and abrasion to knee.
Employee was rolling a pump and finger caught between shiv and belt causing nail avulsion, laceration and left third finger fracture.
10 dB hearing shift with 25dB loss left ear
RED LINE CASE injury date was 2/23/2015- did not exceed first aid level of care until 3-2-2015 employee was getting into skid loader, planted right foot and twisted to sit down, felt pop and pain in knee
employee was hitting a valve with 6lb sledgehammer in a confined area, the hammer spun around in his hand and struck him breaking front teeth
complained of back pain unresolved from December 2014
Re-occurrence of back pain from initial back injury 12-2-2014. States no specific injury but turning wheel valves and hard T valves hurt irritated back condition.
10 dB shift with 25dB loss both ears RED LINE work relatedness determination given 2/25/2015
10 dB shift with 25dB hearing loss RED LINE - work relatedness determined 2/25/2015
Employee was hammering to break a t handle loose, the handle struck his right index finger causing laceration
Was hooking air hose up to stinger, opened air valve and hot material shot out of valve hitting hand causing thermal burn to left hand.
The injured employee sustained 3rd degree burns on both knees and lower legs from caustic liquid that seeped into his PPE
unplugging a shoot, swung hammer and pinched finger between lid and hammer causing contusion
was swinging 8lb sledgehammer doing 3 pump changes and felt discomfort in left shoulder during first valve change,
Was hooking up cable on barge was stringing cable hit a pile of cable on deck and fell forward causing pain in both knees.
chemical burn to right wrist and top of hand, blistering noted
lower back pain was using a cheater bar and was pulling on the cheater bar and the bolt broke, felt back pain
cut arm on a metal plate that supports handrail and received laceration to left arm
was walking in her area when she stepped on the railroad tracks and fell
Temporary leased employee was working under plant supervision when he smashed his left middle finger while using a pipe wrench. The injury resulted in a laceration that required stitches.
hitting a valve and the hammer slipped off the valve causing finger to contact the handle. small avulsion of skin on right index finger
RED LINE CASE INJURY DATE 10/13/14 NOT RECORDABLE UNTIL 10/24/2014 Walked thru thick patch of flock on road. Slipped and fell onto both hands. Complain of pain to right wrist
left forearm cut by a metal band that is used for closing bags at 38M
Walking up steps and felt a pop in left calf, felt instant pain.
relieving pressure off a valve above, the valve above was dripping and hit his hard hat on pipe and caused hard hat and goggles to fall off , chemical dripped in left eye
The drain had stopped flowing and line was assumed to be empty. #30 Mud Floor valve was not seated properly allowing flow to fill line and exit through plug once scale was knocked loose by contractors during their task. Supervisor was checking on progress and was walking away at the time scale was unplugged. A spray of hot caustic came in contact with supervisor's back.
Tightening packing on pump, ratchet gear slipped causing pain in right wrist
At approximately 11:50AM on Friday August 29, 2014, a Turner employee was injured while disposing of scrap material in a metal recycle bin. Employee was struck on the right thumb by a troughing roller that unexpectedly shifted while being placed in the bin.
case from 2014 Hearing loss case from 2014 discovered and reporting date of discovery, review by audiologist revealed hearing loss from 2014
was washing presses and felt hot, cramping in thigh and legs
RED LINE CASE was on a ladder, dropped radio, leaned to catch radio, felt pain later in the afternoon and pain worsened the next morning.
Employee was unbolting a flange when he got product on his leg. The employee went to safety shower and rinsed and then went back to work. The employee left shortly after not feeling any discomfort.
Injury occurred 8/5/14 but did not begin reportable until 8/11/14 when restrictions were placed was opening 24 inch flange door, felt pain in right shoulder and neck
heat illness
Using a shotgun hose to wash press, pressure kicked up and threw body against the cage striking right shoulder.
Was hammering on a shredder to get a part to fit, felt pain in shoulder
Initial injury was first aid, became medical treatment on 7/23/14. Pallet slipped and struck right shin causing contusion.
re-packing pump , puller came loose causing ee to nearly fall, twisted back in process to avoid falling
Employee was inserting air lance into valve and alumina got on wrist.
Employee was taking a sample and spilled chemical on wrist.
Employee was closing valve and was sprayed with liquor on face and arms.
taking a flange loose , hand was slammed into I-Beam
Employee was rodding out an Australian valve and when he got up to look at it he guesses he bumped the caustic valve that was beside it. Caustic sprayed
Employee was adjusting jack stand pipe came down on finger.
Employee was removing impeller from a pump and impeller fell and cut employee.
Pulled a screen box and felt pain in arm.
Employee slipped and fell.
Employee was getting out of Kubota and twisted his knee.
Employee slipped and twisted ankle.
Employee was tapping a wedge under a steel plate resting on concrete at the R-10 Gantry area, while tapping the wedge the wedge shot out from under the steel plate striking the employee in the left shin. Employee received a puncture wound requiring 4 stitches and suffered a impact fracture to the bone require further doctor's visits.
Employee was opening valve with hammer and felt pop on right elbow.
Employee was jack hammering and had weakness in wrist.
hammering and closing valves , pushing and pulling and lifting
Was moving hose and stepped up and had pain in left foot.
Injury date was 4/9/14 Restricted date did not occur until 7-11-14 had ankle injury, reports that since injury this ankle is unstable. Has worked full duty up to 7-11-14
Employee was putting press in service. Valve was stiff and felt pain in back.
Record keeping audit 7/7/14 this was a finding, needed to be added: Walking down stairs, twisted knee.
Red Line Case- Initial report was First Aid only and then came back one month later to report to medical. Employee hit finger with hammer.
finding from enforcement was jackhammering and the hammer jerked causing pain to shoulders and neck
Red Line Case Employee was squatting and when he stood up his knee popped.
Climbing off dozer and hand slipped. Employee jumped off dozer.
Red Line Case Employee was bending down and got light headed. Employee stood up and contacted door.
While walking employee twisted ankle.
grinding on suction valve for about 2 hours alternating with co worker and supervisor, minimal soreness at end of day, woke with pain and weakness to lateral right shoulder with raising arm and overhead motion, right side of back sore
In process of closing knife gate wheel valve for caustic return line to caustic tank in R50 using a wheel valve wrench when the wrench slipped and caught end of left pinky finger between valve wrench and top of R50 caustic tank on edge.
Employee's shift started at 8am. At approx 10am, the employee was injured when the wind caused a door to slam on his right middle finger. When the employee was taken to the clinic for treatment, he was given a post accident drug screen and breath alcohol test. The employee failed the breath alcohol test and was subsequently terminated as a result.
Dropped hammer on foot
Employee was placing a flush hose on the ground and this resulted in the employee receiving a spray of flush water to his right eye.
While attempting to survey the source side of the gauge with a survey meter a gust of wind blew water draining from the upper floor on to the right front side of my hard hat and into my eye.
Employee was stepping out of the door of the Turner office trailer. When she made contact with the deck she rolled her right ankle.
Pulling a crow bar trying to open a latch on a barge. Shoulder pain
RED LINE CASE Employee was walking on grating and felt popped knee.
fell when climbing out of a cargo hold on ship
Climbing ladder and foot slipped. Felt pain in shoulder.
Hearing Shift
Employee's finger was caught between a wrench and metal while disconnecting lugs.
Employee was tightening bolts and wrench pulled free and popped employee in the face.
Lining up pump. Over extended arm
Pt scraped shoulder and knee on handrail.
Employee opened door and got finger caught in door and door jam.
Employee was cleaning bottom of ship floor and he turned and hit ladder.
While hydroblasting the airlift on R-45 #80 precipitator tank, the employee went to top floor of the precipitator tanks to monitor progress of the #80 tank. The tank "burped" splashing the employee with effluent.
Employee was walking to control room and his knee gave out. Employee did not trip or twist his knee. He was walking and his knee gave out.
finding from enforcement was pulling on a battery from reach truck, felt a pop and pain to left ring finger
Employee was tightening the 2 inch that was loose. It broke and sprayed liquor
Red Line Case Stepping over forks of fork truck. She felt knee pain.
Employee was opening a flush valve when he felt a pop in his groin.
Screen box blew out spraying liquor.
Screen box blew and liquor sprayed all over.
Screen box blew out spraying liquor.
Was standing about 8 feet away when a screen box blew out and shot liquor and scale out.
Screen box blew out and shot liquor out.
Pipe rolled off of forklift and struck the top of the employee's foot.
finding from enforcement 8/13/14 moving a portable stand and felt pull in back
Employee was working graveyard shift and got hot and shaky and felt dehydrated. Shift started at 7:00 pm on 7/24/2013. Performing normal routine general mechanical work.
enforcement finding back pain from pulling bending shoveling
Employee was welding in the unit when operations opened an unrelated valve and sprayed the worker with caustic. This resulted in chemical burns to both eyes.
enforcement finding was hammering with a different hammer, at end of shift had soreness and tightness of right shoulder, neck and upper back
Walking to department at the beginning of shift and twisted ankle on broken piece of concrete.
Employee was picking up sandbags off pallet and felt a pain in his back.
Employee was washing a press and the pressure of the water hose knocked him off balance and he struck side of the his back against the press causing a contusion.
Descending a two step ladder that crosses over a trough and he stepped on a large piece of hydrate and twisted his ankle.
Employee was ascending stairs to control cab of gantry crane and started to have low back pain. No slip trip or fall at the time.
Employee was cleaning launder ring on 56-2 tank. He started to feel tired. Reported to medical department and provided with electrolyte replacement fluid. Returned to work.
Employee was swapping pumps #13 and #14 and did not take a break and became overheated.
Employee was assisting with installation of air conditioner and strained shoulder while using a come along to raise unit into place. Patient was placed on restricted duty today 6/28/2013
Employee got feeling nauseated and sick to stomach.
"Red Line Case" No Mechanism of injury Stiffness in elbow for two months prior to report date
Fell down the wooden stairway at R84O trailer. There were 3 steps that the employee fell down. He contused his left knee.
Employee was using a sledgehammer on a screenbox and became dizzy. Patient was taken to the Medical Dept and provided with electrolyte fluid and rest time in cool environment.
Employee strained shoulder while assisting other employee with adjustment to boom on mobile crane. Conservative treatment was not successful and patient placed on restricted duty on 6/21/2013.