Avísenme cuando se presente un nuevo incidente de la MSHA en ACCO STONE CO.
MOVING A TIRE FROM TIRE STORAGE AREA TO BE LOADED ONTO BED OF TRUCK TO BE TRANSPORTED. TIRE FELL FROM CRANE THIS CAUSING DEATH OF OPERATOR.
Going to work on crusher went to use auto crane on F750 service truck when cable bird nested on cable wheel. Pulled all the cable out to rewind on wheel, as they were reeling cable in cable caught employee's glove and pulled it in between crane structure and cable wheel causing injury to fingers
Employee was using digging bar where rock was lodged in chute at Primary plant. Rock dislodged, hit digging bar and smashed employee's left pinky finger. Employee has to wear finger splint until cleared by Doctor.
Employee went to grease line for #2 conveyor when EE tripped, not sure what EE tripped over, tried to catch self and hand landed on a rock causing a laceration. Laceration required 4 stitches.
Employee operating a excavator, throwing material off bench to pit below. Employee called Foreman asked him to come to excavator. Foreman arrived employee stated he did not feel well & left arm hurting. They immediately put employee in vehicle took to hospital. In route notified me I called 800# to report. Employee required 2 stents and will have open heart for one blockage.
Employee was operating a D8 dozer with cab, he was traveling around area that was being stripped of overburden. A rock being seen by employee was misjudged for its size (part of rock was covered with dirt)the track runs over rock when dozer came down it tossed employee forward hitting forehead causing a laceration that required stitches.
Employee and a co-worker was using hammer to clean out a box at old pugmill, co-worker went to hit box, hammer glanced off angle iron, came back and hit employee in eye with hammer. Safety glasses broke and cut employee above eye, requiring stitches.
Employee was down on his knees shoveling material out from under conveyor, when he felt a sharp pain in middle of back. He went to Doctor, told he had some bruising.
EE WAS HELPING ANOTHER EE REPLACE A STAR PLATE ONTO CANICA CRUSHER. USING A CRANE TO LIFT STAR PLATE (45-50#'S)WHILE UNHOOKING PLATE EE HAD HIS FOOT UNDER PLATE & IT FELL 3-4" ONTO HIS FOOT. CAUSED BRUISED FOOT. EE WAS WEARING HARD TOE SHOES. EE DID NOT GO TO DR UNTIL 4/23/04. EE ON CRUTCHES FOR A WEEK.
EE WAS ROLLING UP TARP ON DUMP TRAILER, TARP WAS HEAVY, HANDLE GOT AWAY FROM EE AND HIT HIS ARM, CAUSING A CONTUSION TO RIGHT ARM REQUIRING HIM TO WEAR A ARM SPLINT.
EE WAS CLEANING OUT CRUSHER THAT HAD BEEN LOCKED OUT WHEN A ROCK FELL AND HIT EE ON HIS RIGHT MIDDLE FINGER.
INJURY OCCURRED WHEN INJURED WAS REMOVING BAIL ON DRILL HAMMER USING A WRENCH SPECIFICALLY DESIGNED FOR THIS PURPOSE AND A 2# HAMMER HANDLE BECAUSE HE WAS HAVING TROUBLE GETTING BAIL TO MOVE. WHOLE DRILL HAMMER TURNED INSTEAD AND BECAUSE IT WAS NOT RESTING ON THE GROUND FELL CATCHING INJURED'S FINGER BETWEEN 2# HAMMER HANDLE AND WRENCH. INJURED IS EXPECTED TO MAKE A FULL RECOVERY.
EE WAS PUTTING A CUTTING EDGE ON 988F LOADER WHEN CUTTING EDGE SLIPPED AND FELL ON EE'S LEFT HAND FINGERS CAUSING TWO SMASHED FINGERS AND ONE BROKE FINGER.
EMPLOYEE WAS GETTING IN DOZER, DOOR STARTED CLOSING AND CAUGHT HIS FINGERS IN DOOR, CAUSING CUTS AND SMASHING OF THE MIDDLE AND RING FINGER ON RIGHT HAND.
EE WENT TO CLIMB UP SIDE OF DUMP TRUCK WHEN SLIPPED AND HIT RIGHT KNEE.
EE WAS AT THE OLD SHAKER SCREEN, (NOT IN USE) TURNING A SHEAVE TOP REMOVE BELTS. THE COUNTER WEIGHT SHIFTED AND CAUGHT HIS ARM. THERE WAS A PIECE OF SPOT WELD ON THE METAL WHERE HIS ARM WAS AN D WHEN EE WENT TO PULL HIS ARM OUT IT CAUSED A LACERATION TO HIS RIGHT FOREARM.
EE WAS TRYING TO GET BEARING OUT OF OLD SHAKER SCREEN (NOT IN USE). EE WAS USING A HAMMER AND CHISEL, HE HIT THE CHISEL WITH HAMMER, THE CHISEL FLEW UP AND STRUCK THE EE IN THE CHIN CAUSING A LACERATION.