Amrize Devil's Slide Plant Metal/Non-Metal

Employee struck left hand with mallet while bricking the kiln.

Using a hammer to release some frozen coal when unloading on the Grizzly, EE misjudged EE's aim smashing EE's pinky finger with the hammer. The impact resulted in an open tuft fracture of the right hand 5th digit.

Production tech was completing preheater tower cleaning, tech was using a 6 foot poke bar with a T handle to remove buildup from the riser, as the tech pushed poke bar through the poke door, left middle finger was smashed between the T handle and the riser poke door frame.

Employee was tightening a rope seal using a pair of channel lock pliers. EE was pulling on the rope towards self. The pliers slipped off the rope and EE hit self in the mouth with the pliers chipping a couple of teeth.

Mechanic was sliding the forks on a forklift when mechanic felt a pop in elbow. Mechanic was treated for a strain by healthcare. Later, when minor pain was still persisting, mechanic went for an MRI. It was found that mechanic had a tear in left distal bicep. Mechanic went in for surgery repair 10/11/2021.

EE started feeling ill and went home just before midnight. EE tested positive for Covid 19 the next afternoon. EE had been working with an employee who also tested positive.

EE was changing out the bucket cutting edge on the 966 loader. While using an air gun to remove the nut from the carriage bolt, the partially loose bolt slid down just enough to turn, spun and the sharp edge sliced through EE's glove causing a small laceration. 3 stitches.

Employee was transferring 30lb belt calibration weights from a pickup bed to storage. One of the weights fell on the upper portion of left foot between the steel toe and the ankle. Employee felt it was just a bruise. Employee continued working the next few days. Finally convinced them to get an x ray. Fractured bone in foot.

Employee was removing steel plate from the raw mill chute. After cutting plate employee manually tried to remove it. The weight of the metal was more than expected. It fell 5 feet onto employee's right toe right behind the steel toe of the boot. It dislocated the tip of the pinky toe and required 11 stitches to close lacerations.

Employee hearing tests confirmed an STS at yearly audiometric test.

Employee hearing tests confirmed an STS at yearly audiometric test.

Employee hearing tests confirmed an STS at yearly audiometric test.

Employee was removing a drain plug from a hydraulic reservoir using a 1/2 Snap On breaker bar. The plug was in tight and EE gave it a little extra truck and felt a pop in EE's upper shoulder. EE was taken to a Work Med clinic where they prescribed Celebrex (allergic to ibuprofen) and then put EE on light duty.

Employee was jackhammering material through a poke hole on the tertiary elbow pipe. A chunk of material came loose and fell on the bit of the jackhammer forcing the hammering up, pinning employee's hand against the top of the door causing a fracture of the navicular bone of the left wrist.

A piece of refractory fell and hit the employee on the left side. The piece caused injuries to the employees shoulder, ribs, and leg.

Employee was cleaning the feedshelf in tower area and got dust in his eyes. He flushed immediately and reported. It was treated as a first aid. 2 days later, on his day off, it was bothering him. He went to doc and they removed a spec of grit from his eye. HE DID NOT REPORT TO MGMT THAT HE HAD GONE BACK TO THE DOC UNTIL TODAY 11/7/2011

Employees were trying to dislodge an oversize rock that was stuck in the crusher hopper. They had opened an 18" work door to jackhammer the rock. After 4 hours of work, a smaller baseball size rock fell on to the crusher reel and the spinning motion sent the rock flying out the access door striking the employee in the face/nose. INJURY WAS TREATED AS FIRST AID UNTIL 10/25

Employee was changingout ripper tooth on D11 dozer. He struck the tooth with a 4 lb sledge hammer. A piece of metal came off the tooth stricking him in the right calf. A small chunck of metal (1/4 size of a dime). Doctor removed from leg and put in 2 stitches.

Employees were removing liners from ball mill. Employees were using metal wedge and sledge hammer to break liners loose. Upon hitting liner a piece of metal broke off (1" X 1/4") and stuck in miners thigh. 5 stitches.

Employee were removing roll from coal mill. He working out of manlift inadvertently knocked a 1" drive socket out of the basket. It fell 15' striking employee below in safety glasses. Pressure from the strike, pushed glasses into cheek causing laceration. 5 stitches.

EE wsa breaking up material in bin with a poke bar. Struck hand on side of bin. Laceration between middle and index finger, 4 sutures.

Employee was gathering samples from different locations in the plant driving a Polaris Ranger. She bumped into a curb and fell out the side and sustained a laceration to the back of her head, requiring a few sutures.

Employee was cleaning buildup in the preheater tower feedshelf area with jackhammer. When the buildup fell off the jackhammer slid forward pinching finger between housing.

EE was changing cutting edge to loader bucket of 922 Cat. While loosening stove bolt, it slipped out of square hole, spun and cut EE's L index finger.

EE was barring plugged up material in a bin and smashed his finger between bar and bin.

Employee was cleaning buildup at 291 BC3 head pulley. Smashed finger between bar and concrete - 6 stitches.

Emplyee was working on window mounted AC unit. While repairing the fan blade and balancing it several times, it hit his L index finger causing small laceration.

Employee was cleaning the feed shelf with a 6' metal bar. He banged his hand against the feed pipe while cleaning and mashed his thumb.

EE was cleaning the feed shelf. He smashed his left little finger between the bar & housing, sustaining a laceration.

Employee was changing out blow pipes in baghouse. He was using a pipe wrench to loosen the bars. The wrench slipped smashing his left middle finger. 7 stitches.

EE was walking to area to work. When he got on the shady side of the bldg., he slipped in some mud. When he reached to catch himself he struck his hand on an I-beam causing hairline fracture requiring 2 stitches.

Employee and 2 coworkers were pulling and pushing steel plate. Employee's right hand was between the wall and plate. The 2 coworkers pushed the steel plate which placed employee's right index and middle fingers between the wall and plate, crushing his fingers. Tips of fingers cut, bones fractured, but no amputation of bone.

Employee was working in kiln and got some grit in his left eye.

Employee was changing out dust collector bags. The pipe wrench was used to loosen the holding bars. It slipped under pressure and mashed his left ring finger. Stitches were required.

EE was changing a proximity switch and did not lock out the flapper arm. got his thumb in between arm and bin. It pulled the thumb nail off.

EE WAS DRIVING A 1978 WABCO WATER TRUCK AND WAS UNABLE TO STOP WHEN THE ENGINE QUIT. THE UNIT TRAVELED 300 FEET AND STOPPED ON A BERM. THE WATER SHIFTED AND THE TRUCK ROLLED 3/4. EE RECEIVED 4 BROKEN AND 3 CRACKED RIBS. (EE WAS NOT THROWN FROM VEHICLE.)

EMPLOYEE WAS WALKING DOWN STAIRS, SLIPPED ON THE BOTTOM STEP AND TWISTED HIS FOOT - HAIRLINE FRACTURE, LITTLE TOE. THE EMPLOYEE RETURNED TO WORK FULL DUTY WITH NO DOCTOR RESTRICTIONS.

EMPLOYEE WAS CLEANING A BIN WITH A METAL BAR. MATERIAL FROM ABOVE FELL STRIKING THE BAR AND THE LEVERAGE PINCHED EMPLOYEE'S HAND AGAINST BIN. LACERATION AND TENDON DAMAGE TO RH MID FINGER.

LOWERING RAMP INTO THE KILN- COME ALONG HANDLE SWUNG AROUND AND STRUCK EE RIGHT HAND AND CRACKEDA BONE.

WHILE REPAIRING GUARD, EMPLOYEE CAUGHT HIS LEFT ELBOW ON EXPANDED METAL MATERIAL. REQUIRING 5 STITCHES.

WHILE REMOVING LARGE AIRSLIDE SECTION FROM BLENDER, AIRSLIDE SHIFTED (FELL) AND TORE-SLICED EE'SLEFT THUMB. REQUIRED APPROX 15 STITCHES TO REPAIR LACERATION.

PLUMBING: TIGHTENING A PIECE OF PIPE WHEN THE PIPE WRENCH SLIPPED AND STRUCK HIS HAND, CAUSINGA SMALL CUT.

WHILE CARRYING TRASH OUT TO DUMPSTER, EE SLIPPED ON THE ICE AND TWISTED HIS LEFT KNEE.

HE STEPPED ON SNOW COVERED STEEL, SLIPPED AND FELL, TWISTING HIS LEFT KNEE. HE CONTINUED TO WORK PERFORMING HIS NORMAL WORK UNTIL HE HAD ORTHOSCOPIC SURGERY ON 2-22-01.

LIFTING HINGED METAL DOOR 2 X 3' TO MEASURE MATERIAL IN BIN. DOOR SLIPPED AND PINCHED LH FINGERS CAUSING HAIRLINE CRACK TO LH MIDDLE FINGER.

DEMOLITION OF REINFORCED CONCRETE WALL. EE IN BOOM LIFT TO REACH AND TORCH CUT HANGING REBAR AND CONCRETE. HAND WAS FRACTURED WHEN IT WAS PINNED AFTER REBAR WAS TORCHED AND SWUNG BACK INTO THE BASKET STRIKING HAND.

WHILE LOADING FRONT TRAILER, THERE WAS A SPILL; DRIVER TOLD BULK LOADER HE WOULD CLEAN IT UP WHILE BULK LOADER FILLED THE PUP; LOADER DID NOTHEAR THE DRIVER. DRIVER PULLED AHEAD AND THE LOADER, WHO WAS IN THE SAFETY CAGE, FELL WHEN THE TRAILER PULLED AHEAD; HE LANDED ON FENDER, BREAKING & DISLOCATING HIS LEFT SHOULDER, THEN FELL TO THE CONCRETE FLOOR BUMPING HIS HEAD.

WHILE CLEANING THE ALKALI BYPASS WITH A BAR, THEEMPLOYEE HIT HIS HAND ON THE HOUSING COVER; THISCUT HIS RING FINGER.

REPLACING FAN BELTS. EQUIPMENT WAS LOCKED OUT. A 36" PIPE WRENCH WAS USED ON THE SHAFT. DRAFT CAUSED THE FAN TO ROTATE BACKWARDS, THE WRENCH SLIPPED OFF AND THE EMPLOYEE TRIED TO PULL THE WRE NCH OUT. IT CAUGHT ON THE SHAFT, FLIPPED OVER AND STRUCK HIS LEFT FOREARM.

EE READED IN TO AN OPEN WELDING ROD CONTAINER THAT HAD RAW EDGES. HE SLICED OPEN THE TOP OF HIS MIDDLE FINGER, REQUIRING 10 STITCHES.

WHILE REMOVING A METAL DOOR FOR ROUTINE MAINTENANCE, THE DOOR SLIPPED AND HE TRIED TO CATCH IT AND THE DOOR MASHED HIS FINGER BETWEEN DOOR AND HOUSING.

WHILE WORKING ON A KILN JOB, EE ENTERED KILN ON TEMPORARY RAMP AND CAUGHT THE LEGGING OF HER COVERALLS ON A METAL CLIP CAUSING HER TO TRIP AND LAND ON HER KNEES--BRUISING THE RIGHT KNEE. SWELL ING OCCURRED THE NEXT DAY.

CLIMBED ON METAL RACK STRUCTURE (APPROX. 2' OFF THE FLOOR). WHEN STEPPING DOWN, LOST HIS BALANBCE AND FELL BACK ON THE CONCRETE FLOOR.

WHILE CLEANING THE BUILD-UP ON THE FEED SHELF WITH A POKE BAR. A LARGE PIECE OF MATERIAL FELL WHICH HIT THE BAR AND PINCHED THE HAND BETWEEN THE BAR AND THE FEED SHELF AREA.

WHILE UNPLUGGING THE CRUSHER, HE STEPPED ON A ROCK WHILE WALKING ON THE CATWALK AND SLIPPED. INITIAL TREATMENT WAS FIRST AID. REPORT WAS FILED FOLLOWING HIS DOCTOR'S VISIT.

WHILE CLOSING THE DOOR ON A RAIL CAR, THE BAR ON THE DOOR SLIPPED AND OVER EXTENDED HIS ARM. THE ACCIDENT WAS NOT REPORTED IMMEDIATELY (UNTIL 10/30/98) AFTER HE VISITED A DOCTOR.

WHILE OPENING THE HOOD DOORS ON THE KILN, THE CHAIN BROKE OR THE COMEALONG AND FLIPPED BACK HITTING HIS ELBOW. THE INITIAL TREATMENT WAS FIRST AID. REPORT WAS FILED IMMEDIATLY FOLLOWING HIS DO CTOR'S VISIT.

EE FAILED TO WEAR HARNESS/LANYARDS AND FELL 26 FEET FROM PRIMARY CRUSHER FACILITY TO GROUND. EE WILL BE RELEASED FROM THE HOSPITAL ON 7-7-98 EE PROGNOSIS IS 100%. RECOVERY FROM INCIDENT.

EE WAS IN THE PROCESS OF AN INSPECTION OF THE FLAPPER GATE AREA. HE ACCIDENTALLY PLACED HIS HAND [LEFT] IN THE PINCH POINT OF FLAPPER GATE CONTROL MECHANISM.

EMPLOYEE WAS OBSERVING A CO-WORKER STRIKING A METAL BEARING WHEN A PIECE (SLIVER) OF METAL CHIPPED OFF STRIKING AND CUTTING HIS LEFT CHEEK.DOCTOR NOTED A 5MM LACERATION OF THE LEFT CHEEK AND E ASILY REMOVED THE FORIEGN BODY.

WHILE CLEANING THE PREHEATER TOWER RISER DUCT WITH A CLEANING BAR, EE MASHED HIS LITTLE FINGER AAINST THE HANDRAIL. EE WAS TAKEN TO MDCAY DEC HOSITAL ER WHERE THEY STITCHED HIS FINGER TIP BACK IN PLACE.

EE GRABBED A PIECE OF HOT METAL THAT ANOTHER EE HAD CUT. EE CLAIMED THAT HE DIDN'T KNOW THE METAL PIECE WAS HOT.

EMPLOYE EWAS WORKING IN THE PREHEATER TOWER AND WAS INVOLVE DIN A PREHEATER VESSEL CLEANIGN PROCEDURE. EMPLOYEE LOOKEDUP TO SEE ABOV EHIM AND DUST FELL FROM HIS FACE SHIELD ITNO HSI EYE. DUS T HAD ACCUMULATED ON TEH BERM OF HIS HARD-HAT 2ND WHEN HE LOOKE DUP, THE DUST FELL INTO HIS EYE.

EMPLOYEE WAS WORKINGIN THE PRE-HEATER TOWER AN WAS INVOLVED IN A VESSEL CLEANING PROCEDURE(POKING FEED SHELF, POKING WITH ROD) EMPLOYEE LOOKED UP TO SEE ABOVE HIM AND DUST FELL FROM HIS FACE S HIELD INTO RIGHT EYE. SOME DUST HAD ACCUMULATED ON THE BRIM.

EE WAS ROLLING A PIECE OF PIPE ( 4 1/2" ID SCH 40 BLACK PIPE, 4' LONG). EE LIFTED ONE END OF PIPE 5 INCHES OFF GRATING AND LOST CONTROL OF PIPE. THE PIPE STRUCK TUFT OF DISTAL PHLANGE OF LEFT HAND, FRACTURE. FINGER WAS IN PINCH POINT BETWEEN GRATING AND PIPE. EE WAS WEARING GLOVES.

EE WAS INSTALLING RUBBER PLUGS IN THE WEST END OF MILL #2 BALL MILL. WHILE HE WAS PULLING HIMSELF OUT OF THE POSITION HE WAS IN, HIS RIGHT LEG GOT CAUGHT WHEN HE WENT TO TWIST IN THE CONFINDED SPACE TO GET UP AND OUT HE TWISTED HIS RT KNEE. RT KNEE SPRAIN.

EE SAID HE WAS LIFTING A LINER FOR MILL REPAIR &FELT A SHARP PAIN IN THE GROIN AREA & NOTED A SWELLING ON HIS L SIDE. EE RETURNED TO REGULAR DUTY AFTER BEING SEEN BY CLINIC. HE NEEDS SURGICAL EVALUATION FOR POSSIBLE ELECTIVE SURGERY REPAIR OF HERNIA AS PER NANCY MECHAM, FNP 11/1/97.

EE WAS GRINDING INSIDE THE MILL, EE WAS WEARING SAFETY GLASSES & AN APPROVED FACE SHIELD WHEN HE FELT SOMETHING IN HIS R EYE. FLUSHED FOR 15 TO 20 MIN. EE WAS SENT TO DR AT OGDEN REGIONAL FOR FORIEGN BODY IN R EYE. REFERRED TO OPHALMOLOGY ASSOCIATES. FOLLOW UP WITH BRAD RICHARDS, MD. AT THE TIME EE HAS MISSED NO WORK.

EE OPERATING HAND GRINDER TO CLEAN STEEL WALLS INSIDE OF STEEL BALL MILL.

EMPLOYEE WAS LIFTING A HEAVY PIECE OF METAL TO MINE IT TO ANOTHER LOCATION CLOSE BY. IN DOING SO HE TRIED TO STEP OVER A PILE OF RESIDUE ELECTRICAL WIRE LEFT BY THE DAY SHIFT ELECTRICIAN. HE S TARTED TO TRIP ON THE WIRE SO HE LET GO OF THE STEEL PLATE WHICH FELL HITTING HIS FOOT,INSTEP,REAKING FOUR METATARSAL BONES.

4100 CRANE BOOM WAS LOWERING THE GROUND, EE WAS ONT TOP OF BOOM AND WAS TIED OFF THE CABLE HE WAS PULLING TWISTED CAUSING EE TO SHIFT HIS WEIGHT. FROSTON THE BOOM CAUSED THE SLIP AND FALL. THE FALL WAS ARRESTED BY LANYARD AND HARMESS. EE SWANG IN TO BOOM HIT BOOM WITH RIGHT LEG.

WHILE STRIPPING JACKET OFF CABLE WITH RAZOR KNIFE, THE KNIFE SLIPPED CAUSING DEEP CUTS TO BOTH MIDDLE FINGERS ON THE LEFT HAND.

EE IS AN IRON WORKER AND WAS CONNECTING A STEEL]PLATFORM WITH COWORKER. PLATFORM WAS BOLTED ON EE'S SIDE OTHER EE SIGNALED DOWN ON LOAD CAUSED SLACK IN RIGGING PLATFORM DROPPED DOWON 3-4 FT. EE JUMPED FORWARD STRUCK HIS RIGHT LEG ON A HORZIRON BEAM-FAILURE TO COMMUNICATE WITH

EMPLOYEE SAID HE WAS WORKING ON HIS CAR AND DROPPED AN ALTERNATOR ON HIS RIGHT FOOT.

STRIPPING ARMORED CABLE INSULATION WITH RAZOR KNIFE WITH HOOK BLADE. KNIFE SLIPPED & CAUSED LACERATION.

PORTOPOWER RAM SLIPPED OUT OF HAND AND HIT EE IN THE MOUTH.

EMPLOYEE WAS DRIVING KAWASAKI CART OVER DIRT MOUND WHICH CAUSED THE STEERING WHEEL TO SLIP OUT OF HIS HAND AND STRIKING HIS RIGHT THUMB CAUSING A SMALL FRACTURE ABOVE THE KNUCKLE.

EE WAS WORKING IN HOT WEATHER CONDITIONS. AT LUNCH TIME EE WENT INTO COMEX & CRANK COOL WATER. EE A THIS TIME WAS SUFFERING FROM HEAT EXHAUSTION.

GATHERING TOOL SCRAPPED LEFT WRIST OVER A PIECE OF PLYWOOD. A LARGE SPLINTER STABBED INTO WRIST. CAUSING A MAJOR PUNCTURE WOUND.

EMPLOYEE WAS WALKIGN DOWN COAL MILL STAIRS WITH WELDIGN LEAD COILED AROUND RIGHT SHOULDER ELMPLOYEE STEPPED ON THE TAIL OF THE WELDIGN LEAD WITH RIGHT FOOT THE LEFT FOOT LANDED FLAT ON THE NEX T STEP DOWN CAUSING A TWIST TO LEFT KNEE.

TIGHTENING BOLT WITH A WRENCH. THE WRENCH SLIPPED RIGHT HAND HIT FIBER BOARD.

EMP WAS PULLING ON A TORQUE WRENCH WHEN THE REDUCER BROKE AND EMP FELL 5-6' AND MULTIPLIER HIT HIM IN BACK OF HEAD.

TWO EES WERE MOVING AN ANGLE(3"X3"X3/8"X12'). WHILE IN THE ACT OF MOVING, EE PULLED HIS RIGHT HAMSTRING, STRIAN TO THE RIGHT LEG. EE STATES HE WAS ON UNEVEN GROUND.

EMPLOYEE WAS USING A MILWALUKEE HEAVY DUTY BAND SAW, EMPLOYEE'S LEFT HAND ON THE HANDLE WITH FINGER ON SWITCH TRIGGER, RIGHT HAND ON FORWARD HANDLE CUTTING HANDRAIL TOE PLATE, THE SAW JUMPED E MPLOYEE LET GO WITH HIS RIGHT HAND SAW MAD CONTACT WITH EMPLOYEE'S RIGHT HAND PALMER AREA. EMPLOYEE RECEIVED 5 STITCHES.

EMPLOYEE WAS MOVING A PARTICALY FULL 90 LBS PROPANE TANK AS SHE MOVED TANK SHE FELT A PAIN IN HER LOWER BACK THIS HAPPENED ON 4-11-97 SHE REPORTED IT ON 4-15-97.

EE WAS TAKING DOWN ALUMN. LADDER. THERE WERE TWOOTHER PEOPLE HELPING HIM TO LOWER LADDER. EE WHOWAS INJURED WALKED LADDER DOWN WITH HANDS & ARMSABOVE HIS HEAD. EE FAILED TO REPORT HIS INJURY U NTIL 4-11-97 AT 7:00 AM. EE WORK OT TIL 6:45 ON 4-10-97. LOWER RIGHT SIDE BACK IS SORE.

EMPLOYEE WAS STANDING ON THE FRONT OF A 4000 CRANE AND GETTING READY TO FEED THE CABLE DOWN TO THE FORKLIFT. THE EMPLOYEE STOOD UP FROM A STOOPED POSITION AND HIT HIS HEAD, CAUSING HIM TO FALL TO THE GROUND (APPROX 6').

MAN WAS WORKING ON 2ND FLOOR OF CRUSHER BLDG. HEWAS WRECKING OUT SHORING SCAFFOLD. HE WAS ON SCAFFOLD AND DISMANTLING SECTION ABOVE HIM, WHEN HE HOISTED A PIECE OF SHORING SECTION RAIL DOWN TO LOWER LEVEL, SCAFFOLD WAS LOWERED & HE WENT WITH SCAFFOLD. HE DOESN'T REMEMBER WHAT HE TIERED OFF TO AS AN ANCHOR POINT.

EE STEPPED ON A BOLT AS HE WAS DESCENDING THE STRUCTURE AT 1720 AT SHIFT CHANGE. HE SAID HE WOULD PUT SOME ICE ON IT AT THE HOUSE. ON 3-24-97 HE REQUESTED THAT HE WOULD LIKE A VISIT TO THE CLI NIC FOR A CHECKUP TO SEE HOW HIS ANKLE WAS DOING. DR. SAID HE COULD PERFORM REGULAR DUTIES BUT NO CLIMBING THE IRON.

EE WAS COMING DOWN A LADDER AT THE BAGHOUSE AND SLIPPED ON A PIECE OF IRON THAT ANOTHER CONTRACTOR LEFT AT THE STAIRWAY. EE FELL AND REACH HIS RIGHT HAND OUT TO BRACE THE FALL AND BENT HIS WRI ST BACK.

EE WAS LIFTING 6" WIRE FLANGE BEAMS. THE WEIGHT OF EACH WAS 120 LBS EACH. EMPLOYEE WAS USING A ROPE TO PULL BEAMS INTO POSITION ON THE TOP DECK APPROX. 12 FEET AND THEN PLACING THEM INTO FINAL POSITION.

EE ASSY. STRUCTURE (STEEL STAIR TOWER) ON THE GROUND. ICE & SNOW ON GROUND. THERE WAS TWO COLUMNS SIDE BY SIDE. EES INSTALLING BEAM #607 HORZ. BEAM TO COLUMN. BEAM #607 SLIPPED OUT OF WEB OF C OLUMN 610A CAUSING EE TO JUMP BACK, SLIP OR TRIP ON DIAGONAL BRACE 606F FALLING BACKWARDS HIT GROUND SPUD WRENCH PUNCTURED RIGHT UPPER ABDOMEN.

EE WAS DESCENDING STAIR TOWER ON THE CLINKER BLDG. WITH A PROPANE HEATER IN HIS RIGHT HAND. HE WAS AT THE FINAL FLIGHT BEFORE THE PLATFORM TO DESCEND THE FINAL 7 STAIR TO THE GROUND ELEVATION. HIS LEFT HAND WASON THE HANDRAIL, THE HANDRAIL TURNED, AND EE MISSED THE STEP. HE CAUGHT HIMSELF BUT BUMPED THE CROSS BRACE. FELL APPROX. 15" AND LANDED ON HIS FEET.

EMPLOYEE WAS CUTTING REBAR WITH A SAW. WHEN HE STOPPED HE NOTICED HIS FINGER HAD POPPED OUT OF JOINT.

EE WAS SUPERVISING EES WHEN AN ICE LENS FELL FROM SOME WINTER PROTECTION TARPS 80' ABOVE. THE ICE STRUCK EE ON THE RIGHT FOOT BREAK 2 BONES AND CUASED 4 DISLOCATIONS. THE HIT ALSO CAUSED EE TO FALL AND HIT HIS HEAD.

EE WAS CLEANING UP AROUND THE JOBSITE, WHERE A NUMBER OF OBSTICLES WERE LOCATED. HE BRUSHED UP AGAINST SOME REBAR, KNOCKING CAP ON GROUND. AS HE PROCEEDED TO RETRIEVE CAP HE CAUGHT THE REBAR W ITH HIS LEG.

THIS IS A CONDITION THAT OCCURRED OVER A PERIOD OF TIME THROUGH REPETITIOUS CLIMBING OF STAIRS.ONE TIME, THE EE DEVELPED PROBLEMS WITH THE CARTILAGE IN THE KNEE. RECENT TREATMENT WAS OTHOSCOP IC SURGERY TO REMOVE SOME OF THE DAMAGED CARTILAGE. ACCORDING TO THE DR'S OPINION, THIS WAS RELATED TO WORK.

USING A SKILL SAW TO CUT A PIECE OF 2"X4" LUMBER LENGTHWISE, WHEN THE BLAD STRUCK A KNOT & KICKED BACK 10" CUTTING HIS FINGER.

EE WAS LAYING OUT CHAIRS UP ON THE DECK & TRIPPED OVER THE REBAR MAT UP ON THE DECK.

EE WAS DUMPING A WHEELBARRO 1/2 FULL OF FROZEN DIRT. HE WAS STANDING ON A 4.5' PEDISTAL. THE DIRT GOT HUNG UP IN THE WHEELBARROW THROWING IT OFF TO THE SIDE, IN TURN THROWING THE EE OFF THE PE DISTAL. EE LANDED ON RIGHT HEEL.

EE WAS PLACING REBAR AT CLINKER COOLER WORKSITE. HE THEN BECAME ILL AND COMPLAINED OF CHEST AND ARM PAIN. HE BECAME DIZZY AND UNSTABL. DR. EXAM REPORTED NOT WORK RELATED.

EMP WAS ASSISTING COWORKER IN PROCESS OF PUTTINGSCAFFOLDING PLANKS IN PLACE. STRAINED A MUSCLE IN LOWER BACK, LEFT SIDE.

EMP WAS PUTTING IN GRADE BEAMS AT CLINKER COOLERSITE. WHILE PRYING GRADE BEAMS INTO PLACE HE OVEREXTENDED AND SPRAINED ELBOW.

EMP WAS TURNING TO GET MORE MATERIAL WHILE TYINGREBAR AT THE COOLER BAGHOUSE SITE. HIS LEFT KNEEWAS TWISTED WHEN HIS FOOT HIT THE REBAR AND NOT ALLOWING HIM TO GAIN HIS BALANCE.

EMPLOYEE WAS WALKING IN SOUTH OF CLINKER COOLER BUILDING AND STEPPED ON A SMALL ROCK AND TWISTED ANKLE AND FELL DOWN. HIS ANKLE SWELLED UP.

EMP WAS PUTTING UP FORM WALLS AT THE RAW MILL SITE. TRIPPED OVER DIAGONAL BRACE OF FORM WALL. SPRAINED ANKLE.

EMP WAS DRILLING HOLE WITH 1/2" DRILL MOTOR. DRILL HUNG UP AND EMP TWISTED LEFT WRIST. HE THEN FURTHER INJURED IT PLAYING VOLLEYBALL.

EMP WAS HELPING BACKFILL A RETAINING WALL USING UPRIGHT COMPACTORS. ONE COMPACTOR WAS BEING USEDAND THE VIBRATION FROM IT CAUSED THE 2ND COMPACTOR TO FALL OVER AND LAND ON HIS FOOT.

PLACING REINFOREMENT ROD ON TOP MAT OF 52' CLINKER SILO. FINISHING UP TOP MAT. MOVED AROUND ON STEEL AND FELT A POP IN BACK. EE HAD NO IDEA HOW THE INJURY OCCURRED TILL HE HEARD THE POP IN BAC K AND FELT DISCOMFORT.

EMPLOYEE WAS WALKING ALONG CLINKER COOLER FLOOR AND TRIPPED OVER CABLE COME-ALONG AND FELL HITTING LEFT KNEE WHICH CAUSED IT TO STIFFEN AND SWELL.

WHILE WORKING IN A CONRETE PLACEMENT AREA. HANDLING REBAR IN THE VERTICAL POSITION. THE CRAFTSMAN WAS REPOSITIONING REBAR. HE HAD TO CUT THE TIE WIRE AND HOLD THE REBAR VERTICLE THE REBAR FELL SIDE WAYS AND MASHED HIS LEFT INDEX FINGER. HE PULLED AWAY AND THE LOWER FINGER SKIN AREA WAS PULLEDLOOSE. STITCHES WERE REQUIRED NO LOST TIME.

EE BENDING REBAR WITH BAR, PULLED MUSCLE IN UPPER BACK. IS WORKING ON LIGHT DUTY 3 TO 5 DAYS.

EMPLOYEE WAS INSTALLING BOLTS INTO BOLT PATTERNS IN CONCRETE WALL FORMS, MOVED WRONG AND PULLED MUSCLE IN LOWER BACK.

EMPLOYEE STEPPED ON ROCK AND BRUISED BOTTOM OF LEFT FOOT. NO LOST TIME.

EE WAS LYGIN DOWN ON THE GRASS ALONG WITH COWORKER. THEY WERE CHEKING WIRES ON THE SPRINKLING SYSTEM LOCATED AT THE FRONT LAWN BY THE OFFICE. ANOTHER EE CAME UP FROM BEHIND OF EE AND JUMPED ON HIM WHICH CAUSED CHEST AND RIBS TO HURT.

CRANE NOT SET UP PROPERLY. OUTRIGGERS NOT EXTENDED, OUTRIGGER PADS SET ON UNSTABLE GROUND, PADS WERE NOT CRIBBED. BOOM OVEREXTENDED.

EE WAS REMOVING HARDWARE AN GANG FORMS HE THEN DECIDED TO CLIMB OVER A THREE FOOT REBAR WALL. CAUGHT HIS FOOT IN REBAR AND FELL TWISTING HIS KNEE.

EE WAS LOWERING LOADING SPOUT TO BULK TRUCK WHEN THE SPENT HUNG UP ON LID HINGE. WHEN EE BENT OVER TO FIND WHERE THE SPOUT WAS HUNG UP THE SPOUT SHIFTED AND STRUCK EE S LEFT THUMB, FRACTURING BOX IN THUMB BUCKLE TYPE FRACTURE.

EE WAS HELPING WITH REPAIRS TO #1 CLINKER COOLER. HE PICKED UP TWO BRICK & FELT BURNING SENSATION IN RIGHT GROIN AREA. SEEMED TO GET BETTER UNTIL 2/22/96, SO WAS SENT TO DOCTOR, #1. DOC. #1 TH OUGHT IT MIGHT BE A HERNIA SO REFERRED TO DOC. #2. DOC. #2 DIAGNOSED HERNIA ON 2/29/96.

EMPLOYEE WAS HELPING INSTALL BRICK IN #1 KILN WHEN DUST FRAME COATING BLEW THROUGH KILN GETTING INTO EMPLOYEES EYES EMPLOYEE WAS WEARING SAFETY GLASSES & GOGGLES EMPLOYEE WENT TO DOCTOR TO FLU SH OUT EYES & MEDICATION WAS PRESCRIBED

EE WAS HELPING REMOVE BURNER PIPE FROM KILN WHEN HE TRIPPED OVER A STEADYING CABLE AND FALL TO THE FLOOR. EE CRACKED DISTAL END OF RADIUS IN RIGHT WRIST. STUBBED LEFT GREAT TOE.

EMPLOYEE WAS CUTTING AFILLER FOR A GAS BURNER PIPE WITH OXY-ACCCT TORCH) WHEN IRON PARTICLES GOT UNDER GOGGLES AND INTO EYE. DR REMOVED PARTICLES AND PRESCRIBED MEDICATION.

EMPLOYEE WAS CLEANING AIR CONDITIONER WHEN DUST BLEW INTO EYES EMPLOYEE WAS SENT TO DOCTOR WHO CLEANED EYES & PRESCRIBED MEDICATION

EMPLOYEE WAS GREASING CONVEYOR BELT WHEN HE BENT OVER TO REACH A FILTING HE FELT PAIN IN BACK WATCHED FOR A FEW DAYS & WHEN PAIN CONTINUED HE WENT TO DOCTOR ON 06-23-95 DOCTOR PRESCRIBED PHYSI CAL THERAPY

EMPLOYEE WAS WELDING ON RAW MILL GRATES HE LIFTED WELDING HOOD TO GET A NEW ROD WHEN THE WELD POPPED & A PIECE OF HOT SLAG FLEW OVER TOP OF SAFETY GLASSES & INTO LEFT EYE SENT TO DOCTOR TO REM OVE SLAG FROM EYE DOCTOR ALSO WROTE A PRESCRIPTION

EE WAS WELDING ON COAL MILL, WHILE CHIPPING A WELD A PIECE OF SLAG WENT INTO EYE. WENT TO DR WHERE PARTICLE WAS REMOVED AND PRESCRIPTION GIVEN.

EMPLOYEE GOT DUST IN LEFT EYE WHILE GREASING CLINKER COOLER DUST SCRATCHED EYE & EYE BECAME INFECTED

EMPLOYEE WAS HOLDING METAL TO BE WELDING IN SIDE OF KILN WHEN A PIECE OF COATING ROLLED OFF A PILE AND STRUCK FOOT. WENT TO DR NEXT DAY SEVERE BRUISE REQUIRING PRESCRIPTION MEDICATION. NO BR OKEN BONE SHOWED ON X-RAY.

EMPLOYEE WAS HELPING REMOVE A FAN COVER FROM AN AIR SLIDE BLOWER WHEN THE COVER CAME OFF UNEXPECTEDLY & FELL ON EMPLOYEES FOOT JUST BEHIND STEEL TOE TOOK EMPLOYEE TO DOC NEXT DAY & HE DIAGNOS ED BROKEN BONE IN RT FOOT (RT GREAT TOE)

EMPLOYEE WAS HELPING MAKE REPAIRS TO CLAMSHELL BUCKET AND RECEIVED FLASH BURNS TO EYES FROM WELDING BEING DONE AROUND HIM.

EMPLOYEE STRAINED LOWER BACK WHILE LIFTING BAGS OF CASTABLE TO A MIXING MACHINE. WENT TO DOCTOR WHO PRESCRIBED MEDICATION AND COLD PACKS.

EE WAS HELPING REBUILD RAKES IN SLURRY TANK AND WHEN HE LIFTED A PIECE OF ANGLE IRON FELT A PULL IN GROIN. INCIDENT WAS REPORTED AS FIRST AID. PULLE SEEMED TO GET BETTER, BUT STARTED HURTING A GAINS, SO EE WAS SENT TO DR. 1ST WEEK OF MARCH. HERNIA WAS DIAGNOSED & SURGERY SCHEDULE FOR 3-14-94.

EMPLOYEE WAS WALKING ON TRUCK SCALE WHEN HE SLIPPED AND FELL. HE INJURED HIS LOWER BACK. WINTER WEATHER COULD BE A CONTRIBUTING FACTOR.

EMPLOYEE WAS ADJUSTING CLUTCH ON MACK (1963) WATER TRUCK. HE WAS USING VISE GRIP PLIERS ON THE SLUTCH RETURN SPRING WHEN THE VISE GRIP PLIERS SLIPPED OFF THE SPRING AND STRUCK EMPLOYEE IN THE FACE. RECEIVED BRUISE TO LEFT CHEEK AND CUT BY EYE (CAUSE BY SAFETY GLASSES) REQUIRING 3 STITCHES.

REPAIRING AN OVERHEAD "ROLL-UP" DOOR FROM A JLG MANLIFT. DUCKED UNDER DOOR AND STRUCK RIGHT SIDE OF HEAD ON CORNER OF BASKET. EMPLOYEE RECEIVED A CUT REQURING 6 STITCHES.

KNEELING ON FINISH MILL MANHEAD. PICKED UP MANHEAD LOCKING BAR TO SET IT OVER MANHEAD AND STRAINED LOWER BACK. WENT TO DR AND RECEIVED PRESCRIPTION FOR MEDICTION.

EMPLOYEE WAS HELPING TO SHOOT CLINKER RING IN KILN WHEN HE GOT DUST IN HIS EYE. WENT TO THE DOCTOR ON 6-11-93 FOR REMOVAL OF PARTICLES FROM LEFT EYE.

EE USED LADDER TO ACCESS BED OF 10 WHEEL DUMP TRUCK TO CLEAN LOADING SPOUT WHEN HE STARTED DOWN THE LADDER IT SLIPPED SIDEWAYS CAUSING EMPLOYEE TO LOSE HIS BALANCE AND FALL. EE S RIGHT LEG WEN T THRU THE RUNGS THEN HE FELL TO THE GROUND. MINOR INFECTION SET IN APPROX. 6-1-93 AND WAS SENT TO DR.

UNPLUGGING SHREDDED TIRES (FUEL)FRAM PIPELINE WHEN PIECE OF WIRE PUNCTURED LEFT INDEX FINGER FINGER BECAME INFECTED & REQUIRED DOCTORS ATTENTION ON 03-19-93

EMPLOYEE HAD BEEN WORKING ON AN ELECTRICAL PROJECT THAT REQUIRED A CONSIDERABLE AMOUNT OF KNEELING OVER A 2 WK PERIOD HE REPORTED A SORE RT KNEE ON THIS DATE WENT TO DOC & DRAINED FLUID OFF KN EE

INSTALLING SHEAVES ON #1 KILN BUSTLE FAN WHEN WRENCH SLIPPED OFF & STRUCK EMPLOYEE IN THE UPPER LIP EMPLOYEE RECEIVED A CUT ON THE UPPER LIP THAT REQUIRED TWO STITCHES

54736YEE WAS LIFTING AN I BEAM WITH A BAR WHEN THE BAR SLIPPED AND HIT EMPLOYEE IN THE CHIN. CHIN WAS LACERATED AND REQUIRED SEVEN STITCHES.

54736YEE WAS CUTTING CHAIN WITH OXYLACET WHEN A HOT PIECE OF CHAIN FELL INTO GLOVE. RECEIVED 2ND DEGREE BURNS TO TOP OF LEFT HAND.

81408OT KILN DUST GET INTO EYES WHILE DIGGING CEMENT KILN DUST FROM A CHAINDRAG RECEIVED BUREN TO EYE AND DUST PARTICLES IN EYES EE WAS WEARING SAFETY GLASSES ALL THE TIME AND SAFETY GOGGLES P 19306F THE TIME.

REMOVING BURNER (FUEL) PIPE FROM #2 KILN. RE-ADJUSTING CHOKER TO BALANCE POINT WHEN PIPE SHIFTED CATCHING RIGHT HAND IN PINCH POINT BETWEEN BURNER PIPE AND SUPPORT FRAME.CUT RIGHT HAND MIDDLE FINGER AND BRUISE ON INDEX FINGER.MIDDLE FINGER REQUIRED STITCHES AND SOME SKIN GRAFTING.

EMPL REMOVING KILN BRICK WHEN CLINKER DUST ENTERED RIGHT EYE.EMPL WEARING GOGGLES BUT WERENT FIT PROPERLY.EMPL RECD SLIGHT CHEMICAL BURN TO EYE.

EMPLOYEE AND ANOTHER WORKER WERE ADJUSTING THE HEIGHT OF THE DISCHARGE PLATE OF A BAG CARRYING "FLEX-S-VEYER". EACH ASSUMED THE OTHER WAS GOING TO TAKE THE WEIGHT, WHCN NEITHER DID, THE PLATFO RM FELL CATCHING EMPLOYEES LEFT HAND BETWEEN THE PLATFORM & SATATIONARY SUPPORT (PINCH POINT). CAUSED CUTS TO LEFT HAND REQUIRING 27 STITCHES.

REPAIRING CONV WRENCH SLIPED HE TWISTED BACK

WHILE REPAIRING CEMENT CONVEYOR SCREW, EMPLOYEE WAS USING PIPE WRENCH TO LINE UP GUDEON BOLT HOLES. WRENCH SLIPPED & EMPLOYEE FELL AGAINST HANDRAIL INJURING LOWER BACK. INJURY WAS AGGRAVATED O N 10-4-91 WHEN EMPLOYEE WAS OPERATING A FRONT END LOADER AND FELT PAIN WHEN HE TURNED TO LOOK OUT BEHIND LOADER.

EMPLOYEE WAS USING A STEP LADDER TO INVENTORY MOTORS. WHILE DESCENDING THE LADDER HE LOOKED THROUGH HIS BIFOCAL LENSES AND MISJUDGED THE LAST STEP ON THE LADDER AND FELL TO THE FLOOR INJURING RIGHT ARM AND SHOULDER. SHOULDER PAIN HAS CONTINUED AND WENT TO DOCTOR ON 9-19-91. DIAGNOSED AS ROTATOT CUFF INJURY. PHY. THERAPY AND MAY REQUIRE SURGERY AT A LATER DATE.

REMOVING COATING AND BRICK HOT CEMENT CLINKER DUST FELL FROM TOP OF KILN INTO EMP EYES REC BURNS TO BOTH EYES AND SCRATCHED EYE

EMPLOYEE WAS UNLOADING CEMENT CLINKER FROM A RR CAR-AS HE PROCEEDED TO OPEN THE SECOND DOOR THE BAR HE WAS USING SLIPPED OUT OF THE HOLE IN THE OPENING SPROCKET & THE EMPLOYEE LOST HIS BALANCE . HE FELL TO THE GRATING OF THE HOPPER & HIS FEET FELL THROUGH THE GRATING. FALL CAUSED DOUBLE HERNIA TO LOWER ABDOMEN.

EMPLOYEE WAS REMOVING A BAG OF CALCIUM CHLORIDE FROM A PALLET TO BE ADDED TO A TANK OF SLURRY BAG UNDER THE ONE BEING MOVED FELL INTO EMPLOYEES LEG STRAINING HIS LEFT KNEE ACCIDENT WAS NOT REP

EMPLOYEE WAS WALKING ALONG CATWALK OF OVERHEAD CRANE CHECKING BOLTS. EMPLOYEE WAS LOOKING AT BOLTS WHEN SHE STEPPED ONTO THE OPENING TO THE LADDER TO CRANE OPERATORS CAB. FELL INTO OPENING AND CUT RIGHT LEG BELOW THE KNEE CUT REQUIRED 3 STITICHES.

EMPLOYEE WAS REMOVING SCREEN CLOTH FROM RACK IN STOREROOM WHEN HE LOST HIS FOOTING AND SCREEN SCRAPPED LEFT LEG. TOOK TO DR. FOR TETNAUS SHOT.

EE WAS TRYING TO LOCATE SPOT TO CUT A CHAIN WITH WELDING ROD WHEN ROD CONTACTED METAL BEFORE HOOD WAS DOWN. RECEIVED FLASH TO BOTH EYES.

EMPLOYEE WAS SUPERVISING WORK IN KILN AREA WHEN A SMALL CLINKER PARTICLE HIT HIS LEFT EYE.SIDE OF EYE RECEIVED AN L SHAPED SCRATCH.SMALL PIECE OF CLINKER LODGED UNDER THE EYE LID.EMPLOYEE WAS WEARING REGULAR SAFETY GLASSES.

BREAKING BOLT LOOSE IT GAVE WRENCHED HER BACK

KILN HAND BEEN SHUT DOWN BY POWER OUTAGE DURING EXTREMELY COLD WEATHER. INJURED WAS HELPING RE-LIGHT NATURAL GAS TORCH. ON IGNITION A PUFF OF EHAT BLEW BACK THROUGH SMALL DOOR WHERE THE IGNI TION TORCH WAS INSERTED. EMPLOYEE WAS BURNED BY FLAME AND HOT DUST IN THE BLOW BAK.

THE INJURED EMPLOYEE WAS RETURNING TO THE QUARRY LOADING AREA WHEN HE FELL ASLEEP AT THE WHEEL. THE TRUCK DRIFTED OFF TO THE RIGHT SIDE OF THE HAUL ROAD, RAN INTO SOME OVERSIZED ROCK, AND TIPP ED OVER ON ITS LEFT SIDE. EMPLOYEE WAS WEARING HIS SEAT BELT.

UNLOADING CLINKER FROM RAILROAD CARS EMPLOYEE GET INSIDE CAR TO WORK A CHUNK THROUGH THE DOOR THE CHUNK FELL & EMPLOYEE REACHED FOR THE SIDE OF THE CAR TO CATCH HIMSELF H IS WRIST LEFT POPPED WHEN H IS ARM WENT TIGHT EMPLOYEE RECEIVED TORN LIGAMENTS ON LEFT WRIST MAY NEED SURGERY AT A LATER DATE

EMPLOYEE WAS DUMPING BUCKET OF MUDDY MATERIAL. SOME MUD STUCK IN THE BUCKET AND EMPLOYEE TRIED TO DISLODGE MUD BY KICKING BUCKET WITH RIGHT FOOT. THIS ACTION CAUSED LEFT FOOT TO ACTIVATE THE " DOWN" CONTROL ON BUCKET ARMS WHICH CAUGHT HIS RIGHT FOOT BETWEEN ARM BRACE AND LOADER FRONT. THIS BROKE THE RIGHT FIBULA ABOUT 2" ABOVE ANKLE.

WHILE SANDBLASTING,PIECE OF GRIT ENTERED RIGHT EYE AND SCRATCHED CORNEA.WAS WEARING SAFETY GLASSES W/SIDESHIELDS AND FULL FACE SHIELD.

EMPL WAS DRILLING HOLE IN METAL. DRILL BIT BOUND UP & FORCED HAND AGAINST SHARP METAL CUTTING 2ND FINGER OF RIGHT HAND. TWO CUTS REQUIRED 8 STITCHES.

CHANGING CABLE ON BUCKET OF OVERHEAD CRANE. INJURED WAS USING 15 INCH CRESCENT WRENCH ON CABLE CLAMPS. WRENCH SLIPPED AND HE FELL AGAINST CABLE DRUM. BOLT HEADS WERE SOMEWHAT ROUNDED AND HAVE BEEN CHANGED OUT. RIBS ON RIGHT SIDE HAD PULLED CARTILAGE.

EMPLOYEE WAS AERATING WASTE DUST BIN, WHILE UNCOUPLING HOSE, DUST BLEW INTO LEFT EYE. EMPLOYEE WAS WEARING SAFETY GLASSES, BUT DUST BLEW UP UNDER THEM. THE DUST CAUSED SCRATCHES (CORNEAL ABRAS ION) AND IRRITATION.

EMPLOYEE WAS OPENING A CARDBOARD BOX OF PARTS WITH A POCKET KNIFE AND SLIPPED AND CUT HIS FINGER. THE CUT REQUIRED 3 SUTURES AND A TETANUS SHOT. NO IMPAIRMENT INVOLVED.

INJURED EE WAS RIDING ON 980 CAT LOADER IN OPERATORS COMPARTMENT. HE STUCK HIS FOOT OUT OF THE CAB JUST AS THE OPERATOR TURNED SHARPLY. HIS FOOT WAS PINCHED BETWEEN THE FUEL TANK AND THE LIFT ARM RESULTING IN A BRUISED INSTEP. HE WAS SENT FOR X RAYS TO CHECK FOR DAMAGE THERE WAS NONE.

WHILE CLEANING AROUND THE STEP AREA OF THE #2 CLINKER COOLER, THE INJURED EMPLOYEE TOOK A SHOVEL FULL OF MATERIAL AND FELT A POP IN HIS KNEE. HE WEN TO DR. ON 5-15-89 AND HAD KNEE X-RAYED. T EH DR. DIAGNOSED A TORN CARTILAGE.

THE INJURED WORKER ASKED A CO-WORKER TO TOSS HIM A ELECTRODE HOLDER SO HE COULD DO SOME WELDING. WHEN THE CO-WORKER TOSSED THE STRINGER, THE INJURED EMPLOYEE WASN'T WATCHING AND THE STINGER H IT HIM IN THE MOUTH AND KNOCED A CROWN LOOSE ON HIS UPPER TOOTH.

INJURED WAS LIFTING AND DUMPING 5 GAL. BUCKETS OF WORN GRINDING MEDIA INSIDE OF RAW MILL. WEIGHT OF LOAD WAS APPROX. 60#. WHEN SHE GOT DONE WITH THE LIFTING AND GOT OUT OF THE MILL AND STARTED SWEEPING, SHE NOTICED HER BACK WAS SORE.BY THAT EVENING, SHE WAS HAVING LOWR BACK PAIN AND STIFFNESS.

GRINDING PARTICLE ENTER RIGHT EYE BACK OF EYE GLASS.

HIT LEFT INDEX FINER WITH HAMMER WHILE H WAS DRIVING NAILS.

STEPED ON A BOARD WITH ANAIL PROTRUDING RIHT FOOT REC A PUNCTURE WOUND.

WIND BLEW SANDBLAST SAN INTO EYES RIGHT EYE WAS CHEMICLA BURNED AND IRRIATATED EMP WAS WEARING SAFEY GLASSES AT TIME OF ACC. HEAVY WINDS CAUSED SUST TO BECOME AIRBORNE.

EMPL REACHED TO PICK UP KILN BRICK WHILE OTHER EMPLS STILL BARRING BRICK AWAY FROM KILN SHELL.A BRICK HIT EMPL ON FINGER CAUSING LACERATION.HE WAS TAKEN TO DR AND HIS FINGER REQ 5 STITCHES TO CLOSE WOUND.

INJURED WAS WELDING ON #1 COLLER STACK FAN IN THE FAN HOUSING AND HAD A HOT SPARK FALL BEHINE THE TONGUE OF HIS SHOE. HE SUFFERED 2ND AND THIRD DEGREE BURNS TO HIS LEFT INSTEP. TOTAL BURN AR EA IS 4 CENTIMETERS IN DIAMETER WITH A ONE CENTIMETER THIRD DEGREE BURNED AREA. REMAINING BURN AREA IS SECOND DEGREE BURN.

EMPLOYEE WAS TORQUEING BOLTS ON MILL SHELL WHEN SCAFFOLD PLANK SLIPPED.EMPLOYEE FELL AGAINST SCAFFOLD PIN & SCAFFOLD BRACING.EMPLOYEE HAD WIND KNOCKED OUT OF HIM,BRUISED RIBS AND STOMACH.

EMPLOYEE WAS CA9RYING ELECTRICAL CABNET & TRIPPED & CABNET FELL ON EMPLOYEE'S LEG. EMPLOYEE WAS TAKEN TO HEALTH CENTER FOR X-RAY & PRESCRIBED A PRECRIPTION.

EMPLOYEE WAS UN5OADING MATERIAL OFF OF TRUCK WAS PULLING ON A CABLE CHOKER WHEN HE SLIPPED AND HURT LOWER BACK

EMPLOYEE AL 3 LEGEDLY INJURED HER SHOULDER 01-04-889NO WITNESSES.SHE DID NOT REPORT THE INCIDENT .SHE CONTACTED DR.ON 01-13-88 AND HE PRESCRIBED A RX OVER TH E PHONE.SHE WEN7 TO DR. ON 01-23-88 AND RECEIVED CORTISONE SHOTS AND HER ARM WAS PUT IN A SLING.I(NAME) NOTICED THE SLING 02-02-88 AND QUESTIONED THE EVENTS OF THE ACCIDENT AND SUBSEQUENTLY FI

THE INJURED EMP5OYEE WAS HELPING REBUILD A 6 INCH WELFLEY PUMP. WHEN THE NEW FOLLOWER PLATE WAS BEING PUSHED INTO PLACE THE BOTTOM SLIPPED OFFTHE ALIGNMENT PEGS ALLOWING THE FOLLOWER PLATE TO DROP ON HIS FO2T AND CAUGHT HISF INGER BETWEEN THE PLATE AND THE SHAFT WILL BE A SPLINT ONE WEEK, NO PERMANENT DAMAGE.

INJURED WAS LYI3G UNDER COAL MILL, PULLING ON THE DRIVE BELTS TO ALIGN BEARING SET SCREWS FOR TIGHTENING. HIS COVERALLS GOT CAUGHT BETWEEN THE BELTS AND THE ROTOR SHEAVE. HE GRABBED THE BELTS TO STOP THE SH9AVE FROM TURNING AND HIS FINGER GOT PINCHED BETWEEN THE BELT AND THE ROTOR SHEAVE. HE HAD NO PROBLEM UNTIL 9-15-87 WHEN HIS FINGER BECAME SWOLLEN AND INFECTED. THE FINGER WAS L

A BULK TRUCK HA8 PULLED OFF THE PACKHOUSE SCALES WITH THE RETRACTABLE WALKWAY IN THE LOWERED POSITION.THE R.H. HINGE OF THE WALKWAY WAS BROKEN FROM CONTACT WITH THE TRUCK HATCH.THE VICTIM ATTE MPTED TO PULL T2E WALKWAY BACK INTO THE RAISED POSITION AND THE L.H. HINGE BROKE,ALLOWING THE WALKWAY TO FALL BACK HARD AGAINST A HANDRAIL,PINCHING THE VICTIMS LEFT RING FINGER AND TEARING TH

EMPLOYEE WAS MO5ING A KILN GUN STAND IN ORDER TO CLEAN UP AND ONE WHEEL ROLLED OFF A RAISED FLOOR CAUSING THE STAND TO TIP OVER. HE ATTEMPTED TO KEEP IT FROM FALLING AND FELL UNDER THE STAND AS IT FELL. 3

EMPLOYEE WAS IN5ESTIGATING A REPORT OF A UTILITY POLE FIRE WHEN HE STUMBLED AND ELL INTO THE HOT ASHES WITH BOTH HANDS.

EMPLOYEE WAS OP9NING UP THE FLEXOVEYOR GATE AND CAUGHT HIS THUMB BETWEEN THE GATE AND THE GATE STOP.

EMPLOYEE WAS MO5ING A WELDING OXY-ACET TO THE WORKSITE AND FELT A PULLING SENSATION IN HIS GROIN THE ACCIDENT WAS UNWITNESSED HE WAS OPERATED ON 10-19-87 HE WAS ON VACATION PREVIOUSLY SCHEDU LED FOR 10 DAYS3OF RECUPERATION EMPLOYEE PREFORMED REGULAR JOB DUTIES FROM TIME OF ACCIDENT UNTIL OPEATION

I NAME 3 PLACED HER HAND BETWEEN THE BIT HOLDING LEVER AND THE JACKHAMMER BODY IN ORDER TO POSITION THE JACKHAMMER. WHEN SHE ACUMUATED THE TRIGGER THE LE VER CLOSED ON H9R HAND.

EMPLOYEE STRAIN9D LOWER BACK AS HE WAS LIFTING A BAG OF CEMENT.

RECEIVED A MUSC3AL STRAIN WHEN LOADER STOPPED ABRUPTLY AS THE BUCKET STRUCK MA FROZEN DITCHING DURING CLEANUP OF THE STORAGE AREA.

LACERATION ON B7K OF 1ST JOINT ON RT MIDDLE FINGER CAUSED BY CLINKER STRIKING THE FINGER AND CUTTING IT

WHILE OPENING A3 DOOR HE STRUCK THE DOOR EDGE WITH HIS MOUTH CRACKING UPPER FRONT TOOTH.A CAP IS REQUIRED.

EMPLOYEE STEPPE8 ON A NAIL IN A BOARD DURING THE DEMOLITION OF AN OLD BUILDING AND RECEIVED A PPUNCTURE WOUND TO LEFT FOOT.A TETANUS SHOT WAS GIVEN BY THE DR.

HE WAS DRIVING 5 FRONT END LOADER CLEANING SNOW OFF THE ROAD WHEN THE BUCKET STRUCK A RAILROAD RAIL.HE WAS THROWN INTO AN OBJECT IN THE CAB CUTTING HIS SCALP ON THE LEFT SIDE.

HE WAS KNEELING3TO REMOVE A DRIVE BELT FROM A COAL MILL MOTOR WHEN HIS KNEE POPPED AS HE TWISTED.IT STILL HURT ON 11-20-86 AND HE WAS SENT TO A DR. WHO DIAGNOSED A TORN CARTLEDGE THAT WILL REQ UIRE SURGERY ON312-2-86.

WHILE CHIPPING 5 WELD APIECE OF SLAG ENTERED HIS LEFT EYE CAUSING IRRITATION.THE NEXT DAY INFECTION HAD BEGUN AND HE WAS SEEN BY A DOCTOR.

EMP PLACED HIS 2AND INTO A WHEELBARROW TO STRAIGHTEN OUT SOME BRICK AND WAS STRUCK BY OTHER BRICKS AS THEY WERE THROWN INTO THE WHEELBARROW

EMPLOYEE FELL W2ILE CLIMBING DOWN A CLINKER PILE AND TWISTED HIS LEFT KNEE