Anna Quarries Inc Metal/Non-Metal

Employee was working on screen #4 repairing a drive motor when a piece of consolidated limestone dust fell down onto employee from conveyor #33 located above screen #4. Conveyor #33 was not running at the time of accident. The piece of consolidated limestone dust struck employee in the back.

Employee was working on conveyor 7. While removing the chain from the conveyor drive system employee's left hand thumb & forefinger were pinched and lacerated by the chain.

Employee was straightening a rear access step on a Cat 980G front end loader. The employee was using a steel bar to straighten the step. The bar slipped free causing employee to lose balance and place all his weight and momentum on lower right leg.

EE was painting on processing plant and felt his knee pop when raising from a squatting position. Cont's. to work without restriction on 4/9 & 4/10. Became reportable on 4/11/13 when EE went to doctor due to discomfort. Doctor requested that EE not work for 5 days.

EE slipped and fell while performing maintenance work on 2/14/2012. This became reportable on 4/3/2012 when he went to doctor for the first time and doctor requested physical/occupational therapy after work hours with no work restrictions.

While assembling a cone crusher, the bowl adjusting cylinder was working back and forth. While trying to hold the cylinder in place the injured employee pinched his finger causing a cut that required stitches.

EE was working on a conveyor belt in a kneeling position, when he stood up to re-position himself, he felt a pop and muscle strain in his left knee.

EE strained his back while attempting to pick up a 20 lb object. He has not missed any work but on 3/30/11 he saw a doctor for continued discomfort from 9/27/2010 incident making it a reportable injury.

EE strained a muscle in his left thumb while lifting a pail of nuts and bolts. This became a reportable injury on 3/23/10 when his doctor requested physical/occ. therapy and temporary restricted use of his left thumb.

EE was fusing pipe together, while in the process, he injuried his knee. **This was not diagnosed until 7/23/08.

While dismounting from the trackhoe, he strained his lower abdomen.

Employee was cutting a piece of steel that two other workers were supporting. When he broke through the steel it slid, getting away from the other two workers. The steel plate slid down hitting employee's foot, bending it downward, putting strain in his back.

While pushing off on a stockpile with a front end loader, one wheel of the loader went into a dip in the grade causing a jolt straining his lower back.

Employee was installing steel wear plate in the crushing mill. The load shifted and he twisted trying to control the load, injuring his lower back and leg muscle.

EE WAS HELPING REPLACE A SHAFT IN THE CRUSHER. AS THE SHAFT WAS SWUNG INTO PLACE HE GOT HIS HAND PINCHED BETWEEN THE SHAFT AND HAND RAIL.

REPETITIVE MOTION UP AND DOWN LADDER OF HAUL TRUCK CAUSED STRAIN ON KNEE. (PENDING WORKMAN'S COMP INVESTIGATION)

INJURED WAS REPLACING ROLLER FRAME ON PLANT SURGE BELT. INJURED HIS BACK AND LEFT LEG.

OPERATOR WAS HAVING A LOAD OF DIRT TO WASTE DUMPSITE AS HE COMPLETED DUMPING IS LOAD THE GROUND AT THE REAR OF THE TRUCK STRATED TO GIVE WAY.THETRUCK BEGAN TO SUDE BACKWARD AT THAT POINT THE OPERATOR JUMPED FROM THE CAB TO THE GROUND CAUSING INJURY TO HIS LEFT FOOT AND LOWER BACK. TRUCKSLID APPROX. 30 FT AND WAS STOPPED BY A DIRT BANK AND LOWER BACK. TRUCK SLID APPROX. 30 FT. AND

GREASING EQUIPMENT WHEN HE TRIGGER HIGH PRESSURE HOSE FROM CLOSE RANGE STRIKING HIMSELF IN THE EYE WITH A STREAM OF GREASE.

OPERATOR STOPPED ON HAUL RAMP TO REMOVE LARGE ROCKS FROM HIS PATH. HE KICKED A ROCK OFF THE RAMPAND IN DOING SO STRAINED HIS KNEE

EMPLOYEE WAS REPLACING A WEAR PLATE AT THE CRUSHING PLANT. HE LIFTED A PIECE OF STEEL & INJURED HIS LOWER BACK.

EE WAS STEPPING OFF LOADER, SLIPPED AND FELL, HITTING HIS KNEE ON LOADER STEP.

EE WAS CHANGING SCREENS ON A SCREEN DECK. HE PULLED A SCREEN, SLIPPED AND INJURED HIS BACK.

EE RECEIVED FLASH BURN FROM C0-WORKER WELDING INTHE SAME AREA.

EE WAS IN THE PROCESS OF WASHING UNIT #330 WITH A POWER STEAM JENNY WHEN HE SLIPPED. WHILE TRYING TO CATCH HIMSELF THE LINE OF HOT WATER PRESSURE CAME ACROSS HIS RIGHT FOOT.

EE WAS LIFTING I BEAM OUT OF ROCK HOPPER. HE LOST HIS FOOTING FELL AND BUMPED HIS KNEE ON A ROCK.

EE WAS INSTALLING A SHAFT IN THE PRIMARY CRUSHERHE PUSHED ON THE SHAFT WITH HIS KNEE CAUSING THEINJURY. THIS INJ WAS NOT REPORTED UNTIL 5/24/99

EE WAS LIFTING AND PUSHING ON A STEERING CYLINDER ON A 988B FRONT END LOADER WHEN HE RECEIVED A HERNIA. HE WANTED TO CONTINUE WORKING AND DID NOT SCHEDULE SURGERY UNTIL 1/18/00.

EE WAS INSIDE THE IMPACT CRUSHER, SLIPPED AND FELL BETWEEN THE HULL AND DRUM INJURING HIS KNEE AND FOOT.

EE WAS PULLING WELDING LEADING UP A CONVEYOR BELT.

EE WAS SWINGING A SLEDGE HAMMER WHILE WORKING ON THIS PRIMARY CRUSHER AND FELT A NUMBNESS IN HIS FINGERS

EMPLOYEE SLIPPED ON THE CATWALK AT THE PLANT WHILE HE WAS WASHING OFF THE CATWALK INJURING HIS LOWER BACK.

EMPLOYEE BENT DOWN TO PICK UP A PIECE OF STEEL AND TWISTED HIS LOWER BACK.

EE WAS CUTTING A PIECE OF METAL WHEN A HOT CHUNK OF METAL BURNED THROUGH HIS PANTS AND BURNED HIS LEG.

EE WAS IN THE PROCESS OF SWINGING A SLEDGE HAMMER WHILE DOING MAINTENACE AT THE PLANT. HE EXPERIENCED SOME NUMBNESS IN THE FINGERS OF BOTH HANDS.

EE WAS LIFTING A PIECE OF STEEL WHILE WORKING ON THE SECONDARY PLANT.

REPAIRING DOORS, HIT KNEE ON SCAFFOLD AND REPEATED TRIPS UP AND DOWN LADDER, KNEE STARTED SWELLING AND A KNOT FORMED.

EE WAS PUTTING ON OXYGEN TANK IN THE BACK OF A PICKUP TRUCK. THE BOTTLE SLIPPED AND MASHED HIS FINGER BETWEEN TANK AND A PIECE OF ANGLE IRON.

EMPLOYEE'S FOOT SLIPPED OUT FROM UNDER HIM WHILE IN THE PROCESS OF WASHING OUT SOME BARRELS. HE WAS STANDING ON A PIECE OF WET AND GREASY METAL WHICH CONTRIBUTED TO THE INJURY. INJURY DIAGNOSE D AS LUMBAR STRAIN.

OPERATING END LOADER IN PIT

REPETITIVE MOTION USED IN GREASING THE PLANT PLUS BUMPING THE ELBOW

CLIMBING DOWN LADDER OF LOADER, HE SLIPPED AND HIT HIS KNEE. WAS NOT REPORTED AT TME OF INJURY. HE SAYS THIS IS A REINJURY. REPORTED TO ME ON 724-95.

INJURED MIDDLE AND LOWER BACK WHILE TRYING TO MOVE A LARGE BOULDER IN THE PIT WITH HIS END LOADER.

HE WAS PULLING SCREEN CLOTH OFF OF A SHAKER.

LOAD SHIFTED ON FORKLIFT AND THREW HIM AGAINSTHE CAB.

STRAINED ABDOMINAL AREA WHILE TRYING TO LIFT A RADIATOR.

DROPPED A COLLET ON HIS FOOT WHILE CHANGING SHEAVES ON AN ELECTRIC MOTOR.

SHOVELING MUD OUT OF BUCKET OF ENDLOADER.

PULLED BACK MUSCLE LIFTING OXYGEN AND ACTYLENE TANKS.

PULLED GROIN MUSCLE LFITING OXYGEN AND ACETYLENE TANKS.

INJURED WAS LIFTING A STEARING CYLINDER, WHEN RIGHT ARM WENT NUJMB & LEFT ARM STARTED TINGLEING. HE ALSO HAS SHORNESS OF BREATH.

EE WAS MOVING AN OIL DRUM WHEN HE CAUGHT HIS FINGER BETWEEN IT AND A ROCK CUTTING HIS THUMB.

STEPPED OFF OF CONVEYOR ONTO TRUCK & INJURED HIS LEFT HEEL.

RECURRENCE OF INJURY THAT HAPPENED ON 7-8-93 STRAINED BACK.

WRENCH FLIPPED OFF OF CONVEYOR STRIKING HIM IN THE FOREHEAD MAKING A LACERATION

THE CONSTANT VIBRATION OF THE LOADER STRAINED HIS BACK

NO NARRATIVE SUPPLIED

WHILE CLIMBING OFF OF THE ENDLOADER HE SLIPPED AND JERKED HIS NECK.

HE WAS LIFTING HEAVY FORMS & FELT PAIN IN HIS UPPER TRICEP AREA.

LIFTING & SETTING HEAD IN COMPRESSOR. HE SLIPPED & TWISTED SIDEWAYS AND SET DOWN ON A PIECE OF ANGLE IRON HURTING HIS BACK & BUTTOCKS.

BLADING ROAD BEHIND SHOP HIT BUMP & SLIDE FOREARD BUMPED DASH ON LOADER BRUISING HIS KNEE

EMPL GREASING BUCKET ON ENDLOADER.SLIPPED OFF OF TIRE AND FELL BETWEEN TIRE AND BUCKET. WHILE SLIPPING ARM HIT BUCKET AND BACK WAS ALSO INJURED.

WHILE USING A SLEDGE TO BEAT SEGMENTS OUT OF UNIVERSAL IMPACT NOTICED SHOULDER BEGNINNING TO SWELL AND KNOT APPEARING.

EMPLOYEE PUTTING TOOTH ON SCRAPER. WHILE DOING SO, HE HIT THE STEEL WITH HAMMER AND A PIECE OF STEEL BROKE OFF AND HIT HIM ON LEFT SIDE OF NOSE ON THE FACE.

HE WAS PULLING ON STEEL CABLE TO REMOVE OUT OF HIS WORK AREA.

WAS PULLING WATER HOSE THAT WAS IN A BIND.

EMPLOYEE WAS OPERATING A RUBBER TIRED LOADER & EXPERIENCED CHEST PAINS & NUMBNESS OF HIS LEGS

EMPLOYEE WAS WELDING IN CRUSHING PLANT.HE MOVED THE HAMMERS WHICH CAUSED A PAIN IN HIS UPPER BACK AND NUMBNESS OF HIS ARMS.HE WAS TAKEN TO THEEMMERGENCY ROOM AND LATER ADMITTED TO A HOSPITAL.L ATER AT THE HOSPITAL HE WAS FOUND TO HAVE SOME TYPE OF HEART OR ARTERY PROBLEM.

EMPLOYEE WAS WELDING AROUND CRUSHING PLANT. HE CAUGHT HIS SHIRT ON FIRE WHICH CAUSED THE BURN TO HIS LEFT ARM.

EMPLOYEE WAS PLACING A CHUTE. WHEN THE CHUTE WAS LOWERED EMPLOYEE HAD FINGER UNDERNIETH THE CHUTE WHICH CAUSED THE LACERATION.

EE WAS PULLING ON AN EXHAUST HOSE ON CRUSHING PLANT WHICH CAUSED A STRAIN ON HIS BACK. EE SAW A DR ON 12-21-90. THE DR TOLD HIM TO TAKE OFF WORK UNTIL FURTHER NOTICE. THE EE MISSED WORK ON 12- 21-90 THIS EE ALONG WITH THE MAJORITY OF OUR OTHER EE S WERE LAYED OFF ON THIS DATE 12-21-90.

EMPLOYEE WAS WELDING INSIDE CRUSHING PLANT. AS HE WAS TURNING OVER THE HAMMERS, ONE OF THEM HIT HIM IN THE LEG CAUSING A STRAIN AND CONTUSION OF THE RIGHT LEG.

EMPLOYEE WAS CHANGING DRILL STEELS ON A HYDRAULIC DRILL.ONE STEEL S;IPPED OUT OF EMPLOYEES HAND.WHEN HE TRIED TO CATCH IT HE SPRAINED HIS RIGHT SHOULDER.

EMPL WAS HELPING TO CLEAN BOULDERS OUT OF CRUSHER THE STRAIN OF MOVING THE ROCK INJURED HIS LOWER BACK HE VISITED A CHIROPRACTOR WHO TOLD HIM TO TAKE SOME TIME OFF

EMPLOYEE WAS WELDING ON THE BED OF A TRUCK. WHEN HE LIFTED THE SHIELD TO INSPECT THE WELD, A PIECE OF METAL FLEW INTO EYE. THE PIECES WERE REMOVED BY A DOCTOR.

EMPLOYEE WAS INSIDE CRUSHER DOING REPAIR WORK HE INJURED HIMSELF AS PER PREVIOUS REPORT HE SAID HIS KNEE BOTHERED HIM ALL THE TIME HE WAS BACK TO WORK HE WENT TO SEE A DR ON 12-2-88 WHO TOLD HIM TO TAKE OFF WORK AND REFERRED HIM TO ANOTHER DR

EMPL PULLING HIMSELF UP INTO CRUSHING PLANT TO BEGIN WELDING.STRAINED HIS ELBOW.WENT TO DR 2 DAYS AFTER INJURY.

EMPLOYEE WAS RIDING IN A TRUCK THE DRIVER HIT A BUMP AND I.NAME HIT HIS HEAD AGA INST THE TOP OF THE CAB HE WAS WEARING A HARD HAT BUT HIS NECK WAS INJURED WHEN HIS HEAD HIT THE TOP OF THE CAB

EMPLOYEE WAS CHANGING DRILL STEELS ON A HYDRAULIC DRILL.THE PIN THAT HOLDS THE DRILL STEEL BROKE AND LET THE DRILL STEEL FALL ONN EMPLOYEES LEFTT FOOT.A CONTUSION RESULTED.

EMPLOYEE WAS PULLING A 4 INCH SUCTION HOSE AND STRAINED HIS BACK WHILE DOINF THIS.EMPLOYEE WAS OFF ONE AND ONE-HALF WORKDAYS AND THE WEEKEND.HE RETURNED TO WORK MONDAY 07-11-88.

EMPLOYEE WAS TAPING ELECTRICAL SWITCHES ON THE CRUSHING PLANT WHEN HE BECAME SHORT OF BREATH HAD CHEST PAINS & A COLD SWEAT HE WAS TAKEN TO THE EMERGENCY ROOM & WAS LATER ADMITTED TO THE HOSPI TAL

EMPLOYEE WAS INSIDE CRUSHER DOING REPAIR WORK HE FELL FORWARD AND T RIED TO CATCH HIMSELF WHICH SPRAINED HIS RT KNEE

EMPL LIFTING DR3LL STEEL.STRAIN FROM PICKING UP STEEL CAUSED CONTUSION ON RIGHT SIDE OF CHEST WALL.EMPL DIDNT GET MEDICAL ATTENTION UNTIL 9-28-87.

EMPLOYEE WAS US3NG A PRY BAR TO PUT A TRACK BACK ON A DRILL EMPLOYEES BACK WAS STRAINED FROM PULLING & PUSHING ON PRY BAR EMPLOYEE VISITED CHIROPRACTOR MANY TIMES WITH NO RESULTS HE VISITED A MD WHO DIAGNO8ES THE PROBLEM A DEGENERATIVE JOINT DISEASE & LUMBO SACRAL STRAIN PATIENT MISSED WORK ON 081087 091087 THRU 092187 & HE IS OFF AGAIN NOW 092487

EMPLOYEE WAS DO3NG HIS REGULAR JOB OF WASHING DOWN THE CRUSHING PLANT HE WAS WALKING UNDER A CONVEYOR & HIS HARDHAT HIT THE CONVEYOR WHICH PULLED HIS HEAD BACK CAUSING DAMAGE TO HIS NECK

EMPLOYEE WAS CL9ANING WINDOWS ON HIS TRUCK. HE SLIPPED OF THE CATWALK OF THE TRUCK AND FELL TO THE GROUND, LANDING ON HIS FEET.

EMPLOYEE WAS ST9PPING OFF LADDER OF LOADER. HE MISSED THE BOTTOM STEP AND TWISTED HIS LEFT ANKLE.

EMPLOYEE WAS GE7TING OUT OF BACKHOE AND SLIPPED ON STEP OF BACK HOE WHEN HE LANDED ON THE GROUND HE STEPPED ON A ROCK AND SPRAINED HIS ANKLE

EMPLOYEE WAS LO4ERING THE BOOM ON A DRILL THE KELLY BAR (PART OF BOOM) GOT INTO A BIND AS IT WAS BEING LOWERED WHEN ALL THE WAY LOWERED THE KELLY BAR POPPED OUT OF THE BIND IT WAS IN AND HIT THE EMPLOYEE O3 THE HEAD A HARD HAT WAS BEING WORN A NECK INJURY OCCURED AS PART OF THIS ACCIDENT X-RAYS DARVON AND A SOFT CERVICAL COLLAR WERE GIVEN TO THE EMPLOYEE IN THE EMERGENCY ROOM

EMPLOYEE WAS SI7TING ON LOADER TIRE PRYING ON A PART OF HYDRAULIC CYLINDER.TOOL SLIPPED OFF CYLINDER CAUSING EMPLOYEE TO FALL BACKWARDS OFF LOADER TIRE ONTO FLOOR OF SHOP.

EMPLOYEE WAS CHANGING OIL FILTER ON A LOAER SOME OIL GOT ON TROUBLE LIGHT AND DRIPPED INTO EMPLOYEES RT EYE CAUSING A CORNEAL ABRASION PRESCRIPTION DRUGS (POLYSPORIN & GARAMYCIN) WERE GIVEN TO THE EMPLOYEE

EMPLOYEE WAS TRYING TO REMOVE A SHAFT FROM THE CRUSHING PLANT. HE WAS USING A HAMMER TO REMOVE THE SHAFT. A SLIVER OF METAL FROM THE SHAFT OR THE HAMMER FLEW OFF AND IMBEDDED IN EMPLOYEE\S RIG HT ARM. A TETANOUS SHOT WAS GIVEN AND DRUG WAS PRESCRIBED.

CUTTING PIECE OF METAL WITH TORCH.WHILE INSPECTING THE CUT,PIECE OF METAL POPPED UP INTO EYE. RX DRUG WAS ADMINISTERED.

SUBJECT WAS GETTING INTO PICKUP TRUCK & HIT HEAD ON INSIDE OF PICKUP CAUSING MUSCLE SPASMS. EE HAD HIS HARD HAT ON.

SUBJECT WAS REPAIRING TRACK DRILL, WHEN GETTING OFF MACHINE, EMPLOYEE SLIPPED AND FELL. HITTING LEFT ELBOW ON MACHINE. EMPLOYEE DID NOT GO TO THE DOCTOR UNTIL 09-24-84. THE DOCTOR DID HAVE TO DRAIN THE INJURY.

EE WAS LOADING A HOLE WITH EXPLOSIVES-AMO NIT- ONE OF THE BAGS OF NITRATE STARTED TO FALL OVER & EE TRIED TO STOP IT FROM FALLING OVER. HE SPRAINED 2 OF HIS FINGERS ON HIS LEFT HAND. A PRESC RIPTION WAS GIVEN IN THE E/R. THIS INJURY IS BEING REPORTED BECAUSE OF THE DRUG PRESCRIPTION.

SUBJ WAS MOVING WELDER LEADS -CABLES-FROM ON TOP OF WELDER.A STEEL BAR WAS ON TOP OF CABLES AND FELL OFF ONTO SUBJ RIGHT FOOT CAUSING BRUISE TO TOP OF RIGHT FOOT.SUBJ WAS OFF WORK 1 FULL NIG

EMP WAS CLOSING DOOR ON DRILL AND GLASS FELL OUT OF DOOR ONTO EMP RT THUMB CAUSING FRACTURE AND LACERATION ON RT THUMB

SUBJECT WAS TRYING TO KNOCK HAMMERS LOOSE WITH IRON BAR IRON BAR BOUNCED BACK AND HIT SUBJECT IN THE CHECT CAUSING A BAD BRUISE.

SUBJECT WAS REACHING OUT OF TRUCK WINDOW TO OPERATE THE SWITCH THAT CONTROLS THE ROCK BIN DOORS ON THE CRUSHING PLANT. WHEN REACHING OUT OF WINDOW, SUBJECT PULLED A MUSCLE IN THE RIGHT PART O F HIS CHEST.

EMPLOYEE WAS WORKING ON CRUSHING PLANT, HE WAS TRYING TO PUT A SHAFT INTO A LOADER BUCKET THE SHAFT FELL OUT OF LOADER BUCKET AND HIT EMPLOYEE S KNEE AND ANKLE

SUBJECT WAS OPERATING RUBBER TIRE LOADER. JERKING MOTION OF LOADER CAUSED INJURY TO NECK OF EE. HE WAS RELEASED FROM THE CHIROPRACTOR ON 9-15-83.

EMPLOYEE WAS CLIMBING DOWN LADDER AND AS HE WAS STEPPIN OFF LADDER HE SPRAINED BACK

EE WAS MOVING PIECES OF RUSTY METAL. HIGH WINDS THAT DAY BLEW DUST & POSSIBLY SMALL PCS OF RUST INTO EE\S RIGHT EYE. E.R. TREATMENT WAS GIVEN ALONG WITH PRESCRIPTION APPLIED IN THEEYE. FIRST A ID TREATMENT DID NOT HELP THE PROBLEM.

EE WAS SUPERVISING OVER DRILLING OF LIMESTONE. HIGH WINDS THAT DAY CAUSED DUST OF SMALL PIECES OF STONE TO GET INTO EYE. FIRST AID TREATMENT FAILED TO REMOVE PARTICLE. EMERGENCY ROOM TREATMEN T & PRESCRIPTION DRUG DIRECTLY INTO EYE WAS REQUIRED.