Arcosa Frazier Park Plant# 1603: 167 citaciones de la MSHA Metal/Non-Metal

Employee was using a pry bar to unplug a chute. left hand slipped and knuckles struck a piece of angle iron. laceration to knuckle area between index and middle finger. stitches required.

Lighting kiln and had a puff of hot air to face area

Employee was lowering a loader hood when it landed on employee's co-worker's foot.

Employee was climbing the ladder to the disentegrator deck when they lost footing, causing them to fall to the ground, and employee felt pain in their elbow.

Struck left elbow on extended reach forklift arm rest.

Employee was driving the service truck to the "boneyard". Employee drove over a small 6" dip in the road. As employee drove over the rough terrain employee felt soreness in the neck.

Employees noticed smoke coming out of cooler tower. They called on the radio to alert coworkers of fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish fire with several fire extinguishers. While fighting fire employees were exposed to smoke inhalation. They were given a prescription inhaler

Employees noticed smoke coming out of the cooler tower. They called on the radio to alert coworkers of the fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish the fire with several fire extinguishers. While fighting the fire, employees were exposed to smoke inhalation. They were given a prescription inhaler

Employees noticed smoke coming out of the cooler tower. They called on the radio to alert coworkers of the fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish the fire with several fire extinguishers. While fighting the fire employees were exposed to smoke inhalation. They were given a prescription inhaler.

Employees noticed smoke coming out of the cooler tower. They called on the radio to alert coworkers of the fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish the fire with several fire extinguishers. While fighting the fire employees were exposed to smoke inhalation. They were given a prescription inhaler.

Employees noticed smoke coming out of the cooler tower. They called on the radio to alert coworkers of the fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish the fire with several fire extinguishers. While fighting the fire employees were exposed to smoke inhalation. They were given prescription inhalers.

Employees noticed smoke coming out of the cooler tower. They called on the radio to alert coworkers of the fire. Multiple employees brought fire extinguishers to the cooling tower area. Employees tried to extinguish the fire with several fire extinguishers. While fighting the fire employees were exposed to smoke inhalation. They were given a prescription inhaler

Employee was trying to remove a metal door on the disentegrator. As the door came loose ee lost grip. The door fell and smashed left wrist.

blowing out material with air wand

Employee was cleaning out extruder. The chute that drops down to run out the plugs, slipped and smashed his right ring finger.

Employee was vacuuming debris from jack hammer when a piece of debris flew up under his safety glasses. The debris caused minimum irritation. Employee's condition worsened as time went on. Doctors put him on restricted duty to stay away from dusty environments.

Employee was attempting to throw a rope over a portable water tank that was loaded on a flat bed trailer. When he threw the rope he felt a sharp pain in his left arm. Doctor put employee on restricted duty.

Employee was moving/connecting hose on a portable pump in muddy conditions. He slipped and strained his lower back. Doctor put him on restricted duty.

Employee was helping replace a shaft on a gear box. They were trying to beat the opposite side with a hammer. While holding the opposite side the gear box, it slipped and hit his hand. A small peace of metal was stuck in his left hand.

EE was shoveling underneath a conveyor belt. He struck an object embedded in the ground with the shovel. This caused a contusion to his right wrist.

Employee was installing new V-belts on K-3 shuttle drive using a pipe wrench to roll on belts when the pipe wrench slipped smashing his left index finger between the wrench and motor base. Employee suffered an open wound and hematoma.

Co-worker was using a hammer to drive the pin out of the excavator tracks employee was on the other side when the pin came out and struck his arm. This caused a large cut on employee's right forearm. He returned to work the following day.

Employee was changing out extruder grid when he inadvertenty moved a protective cover over a section of catwalk that was under construction. Employee had been aware and warned of the covering over the catwalk. Employee lost his balance causing him to fall.

Walking around K-3 Kiln gust of wind blew dust and metal particals in face and eyes. a foreign piece of metal went into left eye.

Employee felt hot, went to get more water and felt faint. Safety Coordinator at the facility called paramedics as a precatuionary. Employee was taken to Hospital and later that evening was released.

Employee was in manbasket attempting to weld wear ring on rear of kiln when a gust of wind took it out of his grip and pinched right thumb between new wear ring and rear of hood.

The employee cut his left wrist with a razor knife as he was cutting on a 3" water hose.

Employee was walking by a screen when a piece of material flew into his left eye.

EE tripped on steps, struck left knee on vertical part of hand rail. Fell, got back up, with bruised and scratched left knee.

Employee was filling a rental compressor with diesel. As he lifted the can to pour he lost his footing & fell, hurting his back.

Employee and other ee were attempting to restart a conveyor. as He was cleaning the inside of the convoyer with his arm, Other EE turned on the conveyor.

Truck driver fell off from the back step approximately 3 ft. while tarping trailer and broke his right leg.

While tightening the nose cone bolt with his foot and holding the wrench with his left hand and keeping the bolt from turning with his left foot, the bolt turned catching his left index finger between the end of the wrench and nose cone. This smashed his left index finger.

HE WAS PUTTING A NEW 14" THURST ROLLER ON K-Y COOLER WHEN IT SLIPPED AND PINCHED HIS RIGHT RING FINGER.

Hot dust putting out of rotary kiln #3 flew into eyes as i was walking by. Prescription issued 1-26-05.

EMPLOYEE WAS DUMPING HOT ROCK ONTO PILE WHEN WIND BLEW HOT AMBERS ONTO HIS ARMS, LOWER BACK AND NECK. EMPLOYEE LIFTED BUCKET OF BOBCAT ABOVE CAGE TO DUMP.

EE WAS DESCENDING STEPS WHEN HE FELT SHARP PAIN IN JAW. EE HAD AN INFECTION IN HIS JAW. EE PULLED HANDS OFF OF HANDRAILS TO GRAB AT HIS FACE. EE LOST HIS BALANCE & FELL & BROKE RIGHT LEG BETWEEN KNEE & ANKLE.

DURING DRIVEBELT REPLACEMENT, DRAWING V-BELTS THROUGH A SIX-GROOVE SHEAVE ATTEMPTING TO ROLL THE V-BELT INTO PLACE, HE PINCHED HIS LEFT INDEX & LITTLE FINGER BETWEEN SHEAVE & DRIVEBELT. MEDICATION: CEPHALEXIN FOR INFECTION, PROPOXYPH FOR PAIN, NAPROXEN FOR INFLAMMATION.

WAS CLIMBING OFF 966F LOADER GOT OFF THE LOADER TURNED TO WALK AWAY FROM THE LOADER AND FELT SOMETHING TWIST IN HIS BACK.

WAS WALKING BY WATER TANK FELL IN HOLE THAT WAS MADE BY OVERFLOWINNING WATER. STRAIN TO GROIN.

HIS EXTRUDER WET PLUGGED WENT TO DIG OUT LIFTED GAURD HELD IT UP ON HIS SHOULDER WHILE SHOVELING INTHE EXTRUDOR THE SHOVEL STUCK IN MUD GUARD FELL OFF HIS SHOULDER CAUSING A CONTUSION TO HIS L EFT MIDDLE FINGER.

DOING HIS NORMAL DAILY ROUTINE OF RUNNING THE RAW PLANT HE STRAINED HIS LOWER BACK. REPORTABLE BECAUSE OF THE PRESCRIPTION PILLS. MOTRIN, FLEXERIL, VICODIN.

WAS WALKING DOWN ACCESS RAMP SLIPPED ON LOOSE MATERIAL THAT HAD SPILLED ON RAMP AREA AND FELL, LANDED ON HIP, STRAIN TO BACK, KNEE, SHOULDER.

WAS CHECKING OUT HIS COOLER AREA SLIPPED ON SOME WET MATERIAL AND SPRAINED RIGHT KNEE. THIS WAS NOT RECORDABLE AND NOW THEY WANT TO SEND HIM TO THERAPY AND AN MRI

WAS PLACING SQUARE TUBING PIECE OF STEEL ON GROUND END SLID DOWN ACROSS FINGERS CUTTING FINGERS.

EMPLOYEE WAS USING A 2 LB SLEDGE HAMMER AND A BOLT TRYING TO REMOVE ANOTHER BOLT OUT OF THE HAMMER MILL ROTOR. HE SWUNG THE HAMMER AND HIT HIS LEFT THUMB CAUSING MEDIAL AND LATERAL LACERATIONS AND CRUSHING THE TIP OF HIS LEFT THUMB.

EE WAS FIXING A WATER LINE IN A TRENCH, EE WAS FINISHING UP THE JOB. WHEN HE STARTED WALKING BACKWARDS, HE TRIPED & FELL STRICKING HIS LEFT ELBOW ON THE GROUND.

PULLING OIL BARREL TO LEVEL IT OUT MARCH 2000. SHOVELING MATERIAL OUT OF SURGE TUNNEL PULLING GROIN AREA.

SWINGING A HAMMER TRYING TO TAKE A KNIFE OFF THE EXTRUDER SHAFT.

WAS KNEELING ON CATWALK TIGHTENING THRUST ROLLERS ON KILN. MADE HIS SORE AND SWOLLEN.

WAS GETTING OFF LOADER SLIPPED AND FELL WAS HOLDING ONTO HAND RAIL.

EMPLOYEE WAS CLEANING CHUTE WITH A BAR. BAR SLIPPED AND HIT HIS HAND ON THE CORNER OF THE CHUTE.

EMPLOYEE WAS USING A BAR TO UNPLUG A CHUTE, WHEN HE JAMMED HIS THUMB INTO THE CHUTE.

PUTTING COMPUTER BACK TOGETHER WHILE PUTTING IN THE SCREWS THE SCREWDRIVER SLIPPED PONCTOSE LEFT HAND.

MOVING A STEEL BEAM WITH A FORKLIFT IT WAS SHAKEN A LITTLE BIT SO HE PUT IT BACK ON THE GROUND TO REPOSITION IT HE PICKED IT UP WITH HIS HANDS TO MOVE IT AND DROPPED IT ON HIS FOOT.

EE WAS INSPECTING BAGHOUSE AREA AND SLIPPED AND TWISTED HIS RIGHT KNEE.

WAS TEARING DOWN EXTRUDER IN RAW PLANT.

WAS CHECKING HAMMERMILL OUT TO SEE IF IT WAS RUNNING COULD NOT SEE IF IT WAS RNNIGN AND COULD NOT HERE IT. PUT HAND INSIDE GUARD AND DRIVE BELTS GRABBED HIS HAND AND PULLED IT IN. AS OF THIS DATE THIS IS WHAT WE THINK POSSABITY HAPPENED.

CLEANING HAMMERMILL AREA LEFT HAMMERMILL DECK WALKED DOWN CATWALK SLIPPED ON THE MUD ON THE CATWALK AND FELL ON HIS LEFT ELBOW AND WRIST

WHILE TRYING TO FORM A RING ON THE KILN, JACK AND CHAIN HE WAS USING SLIPPED AND SMASHED HAND.

WHILE SETTING SCREEN DECK INTO SCREEN FRAME DROPPED SCREEN DECK ONTO FINGERS.

WAS PLANTING TREE AT ENTRANCE ROAD. TWISTED AND PICKED UP TREE STRAINING LOWER BACK.

WAS CLIMBING OFF LOADER SLIPPED OFF THE STEP ANDSTRAINED HIS RIGHT KNEE.

WALKING ON OIL SLAB TO GET CLEANING SOLVENT. SLIPPED ON OIL AND LANDED ON BOLT & HIP STRAINING HIP.

STANDING ON LADDER & BY KEEPING HIS BALANCE MOVED AROUND & TWISTED HIS KNEE & REINJURED LEFT KNEE

WAS HOISTING SCREENS TO TOP TANKS. REACHED OUT TO GRAB SCREENS. CABLE CAME OFF, SNAPPED BACK AND HIT HIM IN FACE AND CHIPPED HIS TOOTH.

WAS CHANGING SCREEN DECKS ON TOWER SCREEN BUMPED FOOT AGAINST RAIL TOLD OF INJURY ON 8-4-95.

SHOVELING IN QUARRY TUNNEL AND HIS RIGHT ELBOW POPPED.

WAS SHOVELIGN ON HAMMERMILL DECK TO PULL GUARD OUT OF DIRT AND STRAINED HSI BACK.

WAS LIFTING A PIECE OF STEEL OUT OF THE LOADER BUCKET & STRAINED HIS BACK.

WAS CLEANING AROUND THE EXTRUDER DECK & SLIPPED & STRAINED HIS KNEE & ANKLE. WAS REPORTED ON 4-11-95.

WAS JACK HAMMERING OUT HAMMERMILL. HE WAS KNEELING ON CATWALKS AND BRUISED KNEE. WAS INFORMED OF INJURY ON APRIL 11, 1995.

GOT OFF LOADER CROSSED EXTRUDER DECK CLOD FELL OFF OF BELT STRIKING HIM IN THE HEAD AND NECK AREA.

HE WAS CLEANING THE MUD OFF THE EXTENDER WATER BAR PIPE SLID INTO AUGER PULLING THE PIPE THOUGH HIS HANDS AND CUTTING OF HIS FINGERS AND LOSING ONE OF HIS FINGERS. LEFT HAND TO FIRST KNUCKLE.

HAD TO CARRY A 5 HORSE MOTOR UP THE CATWALK.

WAS WELDING ON CROSS TUNNEL TO OPEN IT UP TO PULL THE SYNTRON OUT.

WAS WELDING ON BUCKET ELEVATOR LEANED OVER TO WELD ON SIDE OF ELEVATOR AND SLIPPED HITTING HIS HEEL ON HANDRAIL.

WAS CLEANING INCLINE BELT CHUTE, PICKED UP DIRT CLOD, TURNED TO THROW, AND TWISTED LOWER BACK.

WAS SHOVELING DIRT ONTO CONVEYOR TWISTING BACK &FORTH

WALED OUTSIDE THE MAINTENANCE SHOP STEPPED INTO SOFT MAT IN THE DRIVEWAY & TWISTED ANKLE & SPRAINED FOOT

UNPLUGGING CHUTE, CUT FINGER ON TAIL PULLEY GUARD, DRAGGED FINGER ACROSS GUARD.

WAS CLEANING SAND SCREENS ON TOP OF FINISH TANKS. HE SLIPPED ON A PIECE OF ANGLE IRON ALL FELL ONTO.

CHECKING THE RAW MATERIAL FALLING ONTO BELT TURNED TO WALK AWAY FINGER WENT THROUGH HOLE THAT WAS WORE INTO BRAND AND SHAFT CAUGHT FINGER.

WAS TAKING OFF WATER METER.WRENCH SLIPPED OFF METER AND SMASHED AND CUT FINGER.

WAS REBRICKING K-4 KILN KNEELED DOWN ON A BROKEN PIECES OF BRICK.

CHANGING ATTACHMENTS ON BOBCAT,FOOT SLIPPED AND HIT RETRAC FOOT PEDAL AND IT CURLED BACK AND CAUGHT HIM.

RAISED HIS HEAD HIT BEAM.

GOING DOWN STEPS EATHER CONDITIONS WET SLIPPED & FELL LANDING ON ELBOW.

REP TAIL PULLEY GUARD DROPPED CAUGHT TIP OF FINGER IN TAIL PULLEY.

HE WAS WORKING ON INCLINE BELT STANDING ON GRAVEL PILE. HE SLIPPED AND REACHED TO CATCH HIMSELF AND HIS WEIGHT WRENCHED HIS BACK.

EMPL WAS MEASURING & MARKING DISTANCE AROUND KILN HE WAS TANDING ON TRUNION BASE & AS HE STARTED TO GET DOWN HE LOST FOOTING & FELL APPROX 2' HE LANDED ON CAN OF WELDING ROD TURRNING ANKLE & B ROKE BONE IN FOOT.

MAN HAD HAND TOO CLOSE TO FAN ON WELDING MACHINE & FAN BLADE CAUGHT GLOVE. BADLY BRUISED INDEX FINGER ON RIGHT HAND.

WAS PUTTING ROLLS ON CRUSHER & ROCKS FELL INTO LEFT EYE.

MAN WAS ON CLAIMS CHECK TAKING SAMPLES OF SOIL. HE SLIPPED IN MUD, TWISTED HIS KNEE AND FELL.

MAN WAS CARRYNG A STEEL PLATE INSIDE KILN STEPED ON A ROCK AND LOST BALANCE TRIED TO AVOID DROPPING LOAD AN PULLED MUSSEL IN R. HIP.

EMPLOYEE WAS SH2VELING BY CONVEYOR THEN EMPLOYEE WAS WALKING A WAY FGROM CONVEYOR WHEN HIS PANTS LEG GOT CAUGHT IN CONVEYOR AND PULLED HIS FOOT INTO CONVEYOR AND PIN HIS FOOT.

EMPL REMOVING R2CK FROM CHUTE.

PREV.SHIFT OPER5TOR HAD BEEN PUSHING AND SCOOPING UPLOOSE MATERIAL IN AREA BETWEEN SCALEHOUSE AND LONG BELT CONV GOING TO FINISH TANKS LEAVING A BERM OR RIDGE OF LOOSE MATERIAL 8-10'' HIGH WHE RE GROUND IS NO9MALLY FLAT.IN THE DARK DIDNT SEE THE BERM,TRIPPED AND FELL ON LEFT ELBOW AND SHOULDER WHILE RUNNIG TO MAKE EMERGENCY SHUTDOWN OF SURGE TUNNEL BELT CONV WHEN CLINKER WEDGED BET

EMP WAS CLEANIN1 OUT EXTRUDER WHEN DIESEL FUEL AND CLAY SPLASHED INTO HIS EYES

WAS RIDING IN L2ADER & HIT RT ELBOW ON LOADER DOOR

EMPLOYEE CAUGHT3SHOVEL IN TAIL PULLY AND SHOVEL HANDLE HIT EMPLOYEE UNDER RIGHT EYE.

WHEN EMP WAS CL9ANING CATWALK A DIRT CLOD ROLLED FF CONVEYOR AND HIT EMP IN RT HIP

EMPLOYEE WAS CH5NING GRID ON EXTRUDER AND PINCHED RIGHT THUMB BETWEEN GRID AND PLATE.

SLIPPED ON CATW5LK & TWISTED KNEE.

CLEANING WET CL5Y FROM COOLER CHUTE ON KILN DECK-WHILE PRYING A CHUNK OF CLAY FROM THE CHUTE, SLIPPED & STRUCK KNEE IN IRON.

WHILE PRYING A 7HUNK OF WET CLAY FROM COOLER CHUTE-ON KILN DECK-RIGHT HAND STRUCK A PIECE OF ANGLE IRON METAL IN SEMI-DARKNESS. BACK SIDE OF HAND SUSTAINED THE BLOW.

BUMPED RIGHT KNEE ON ACCESS LADDER ON 966" FRONT END RUBBER TIRED SKIP LOADER AS STEPPED BACKWARD TO DISMOUNT, PULLED HAMSTRING-RIGHT LEG.

WHILE STEPPING OFF PLATFORM FOOT SLIPPED LOST BALANCE TWISTED WHILE TRYING TO REGAIN BLANCE.

WHILE PULLING CLINKERS FROM KILN DROPPED CLINKER PULLER ON RT FOOT