Chantilly Crushed Stone Incorporated Metal/Non-Metal

Employee was using a chipping motion with a bar to knock ice off of a screen deck prior to running. While doing this, employee's hand made contact with the plant causing a "right fifth metacarpal fracture"

Employee was using sledge hammer to knock a shaft out of a water pump for rebuild. While swinging the hammer, employee felt a pop in EE's left side.

DRIVER WEIGHED AT THE SCALES FOR DELIVERY AND WAS OVERWEIGHT. DRIVER PULLED OFF TO OUR DUMP OFF BIN TO DUMP SOME MATERIAL BEFORE BEING WEIGHED AGAIN. WHILE CLIMBING DOWN TO UNLOCK TAILGATE, DRIVER SLIPPED ON STEPS AND TRIED TO CATCH SELF ON THE MUFFLER COVER. THE SHARP EDGES ON THE MUFFLER COVER CUT RIGHT RING AND MIDDLE FINGERS.

Employee was pressing a sleeve out of crusher with a port a power. After pressing it out, employee began disassembling port a power. During this time the steel cross bar that was holding the port a power fell and struck EE's finger.

Employee reached up through a guard to check belts shortly after the machine turned off. The machine was still in motion and the belts took the employee's fingers through the pulley.

Employee was walking to car at the end of day when employee lost balance and fell.

Employee was loosening bolt on a screen. While trying to keep the nut secure, the nut turned and pinched EE's thumb resulting in a small laceration.

Employee was performing maintenance to an articulating truck. As they were loosening the caliper bolts, employee was pushing down on a breaker bar. The bolt came loose and the employee fell forward into the truck, causing a laceration to the eye.

Employee was getting bag out of Pickup truck. Employee stepped on tire to reach bag. Upon lowering back to the ground, the employees leg was injured.

Employee was assisting repair in a conveyor belt that broke. While untwisting the belt a rock that was twisted up in the belt came loose and fell, bounced off the beam of the take up pulley and struck the employee.

Performing engine repair on 992C Wheel Loader. Cleaning air filter with sanding pad attachment. Piece of metal flew into Left eye. Eye became irritated next day. Given Rx and referred to ophthalmologist 7/13.

While climbing down a ladder on the plant, the employee slipped and fell into the ladder on the right side.

Employee was unloading a box of welding rods from a truck. The box slipped and while trying to maintain control of the box the employee felt a pull in their shoulder/arm.

Employee was using a cutting wheel to cut a bearing out of a crusher. While cutting the bearing the wheel kicked back and cut the employees right arm.

Employee was cleaning out a feeder shoot on the plant. While clearing out a tree root, employee brushed up against the shoot and cut arm.

Employee was carrying a container of welding rods and cut fingers on the container.

After employee finished fueling the drill, employee was putting hoses away. While walking to the truck to hang the nozzle, employee tripped over track marks left in the ground from the drill.

Employee slipped on ice while climbing down from a loader. EE caught self with EE's arm and felt a pull in EE's shoulder.

Employee was climbing down a ladder after making repairs to a 992D Loader, when the ladder slipped out from underneath him causing him to fall. while falling he made contact with the tire and injured his back/neck.

The maintenance crew was moving a conveyor up the ramp to the top of the tunnel stockpile area. A Kobelco LK 300A wheel loader was used to move the conveyor up the ramp. The chain used to lift the one end slipped through the eye in the bucket, causing the loader to overturn on the employee who was walking on the left side of the machine.

EE WAS DISASSEMBLING THE FMC MF800 VIBRATORY FEEDER. THE EE WAS INT HE PROCESS OF REMOVING THE FASTNERS FOR THE SECOND COUNTERWEIGHT WHEN THE FIRST COUNTERWEIGHT SPUN ON THE SHAFT. THE EE S RI GHT THUMB WAS PINCHED BETWEEN THE TWO COUNTERWEIGHTS.

EMPLOYEE WAS WORKING WITH EMET GUTIERREZ CHANGING A HOIST CABLE ON DB-04C AN 80D NORTHWEST CRANE. THE EMPLOYEE WAS ATTEMPTING TO HOLD THE 1 1/8"CABLE WHILE IT WAS BEING INSTALLED IN THE HOIST DRUM OF THE CRANE. IT CAME FREE STRIKING THE EE IN THE FACE.

EMPLOYEE WAS EXITING THE CAB OF THE FUEL TRUCK FT-03C, WITH AN UNPROTECTED RAZOR BLADE IN HIS RIGHT HAND. AS HE BEGAN TO CLIMB OUT OF THE CAB, HIS RIGHT HAND STRUCK HIS LEFT HAND WITH THE RAZO R BLADE.

EMPLOYEE WAS REMOVEING A 4 LB. HAMMER WHICH WAS USED AS A BLOCKING DEVICE ON THE 6'X14' SCREEN DECK. THE EMPLOYEE'S LEFT MIDDLE FINGER WAS PINCHED BETWEEN THE SCREEN DECK FRAME AND THE HAMMER HANDLE.

EE WAS RECEIVING HIS OPERATOR TRAINING ON THE WATER TRUCK. THE ACCIDENT OCCURRED NEAT THE DUST COLLECTOR AND 21A PILE INTERSECTION. INSTRUCTOR WAS WEARING THE CAB SEAT BELT AND EE WAS WEARING A SAFETY HARNESS TIED OFF TO THE SEAT FRAME AND THE ROPS CAB. THE TRUCK STOPPED AT THE INTERSECTION. WHEN THE TRUCK RESUMED ITS TRIP, IT ENTERED A DIP IN THE ROAD. EE WAS THROWN FROM CAB AND

EMPOLOYEE WAS DISMOUNTING FROM THE RIGHT SIDE OF DZ-37C. A D-7H CATERPILLER BULLDOZER, SUING THREE POINTS OF CONTACT. AS HE PLACED HIS RIGHT FOOT ON THE BLADE ARM STEP, HISS FOOT SLIPPED CAUS ING HIS RIGHT KNEE TO BE WEDGEED BETWEEN THE BLADE ARM AND THE TRACK FRAME.

EE WAS WORKING WITH OTHER CREW MEMEBERS REMOVINGTHE GRIZZLY FROM THE PUGMILL TRANSFER BOX. THE 6000 LB GRIZZLY WAS LIFTED STRAIGHT UP BY THE CRANE OPERATOR. AS IT WAS LIFTED IT SWUNG TOWARDS THE CONTROL HOUSE. EE ATTEMPTED TO GUIDE THE GRIZZLY AWAY FROM THE CONTROL HOUSE TO PREVENT DAMAGE TO IT. IN DOING SO, HIS RIGHT INDEX FINGER WAS CRUSHED BY GRIZZLY AGAINST A HANDRAIL

EMP WAS LIFTING ONE END OF A CUTTING EDGE WHICH WEIGHED APPROX 200 LBS. AS HE WAS LIFTING THE ONE END UP HIGH ENOUGH TO SET IT ON A SHORT TABLE,HE EXPERIENCED LOWER BACK PAIN.

EE WAS DISMOUNTING FROM THE OPERATOR'S CAB OF A WATER TANKER, USING THREE POINTS OF CONTACT. HE PLACE HIS LEFT FOOT ON SOME SURGE STONE. AS HE PUT THE WEIGHT OF HIS BODY ON HIS LEFT FOOT, HIS FOOT TURNED OVER.

EE WAS MOVING A TRANSFORMER FRAMEWORK WHICH WEIGHED APPROX 250 LBS. AS HE WAS REPOSITIONING THE FRAMEWORK, HE LOST HIS FOOTING, AND THE FRAMEWORK, PINCHED HIS RIGHT KNEE BETWEEN IT ANE AND THE FABRICATION TABLE

EE WAS WALKING OUT OF THE OPERATOR'S CAB OF SH-17C, A KOBELCO K-975 FACE SHOVEL. HE CAUGHT HIS RT FOOT ON SOME MACHINE PARTS THAT WERE IN THE WALKWAY, TWISTING HIS RT KNEE.

EMPLOYEE WAS STANDING ON THE LADDER OF FT-03C DIRECTION L-19C, A CATERPILLAR 992B WHEEL LOADER, TO THE BACK OF THE FUEL TRUCK TO BE FUELED. THE FUEL TRUCK OPERATOR TUNRED AWAY FROM THE LOAD ER TO ZERO THE FUEL METER. THE LAODER OPERATOR COPNTINUED TO BACK UP WHILE HE WAS WATCHING THE FRONT OF THE LOADER SO HE WOULDN'T HIT THE FUEL TRUCK. HE PENNED THE FUEL TRUCK OEPRATOR BETWEE

EE WAS CUTTING STRAPS THAT HELD DUCTWORK. WHEN HE CUT ONE OF THE REMAINING STRAPS, THE WEIGHT OF THE DUCTWORK FORCED THE EE TO HOLD THE WORK, CAUSING THE LADDER TO SLIP AND FALL. THE EE FELL 5 -6 FT INTO AN OPEN BARREL WITH ONE LEG IN AND THE OTHER LEFT OUT.

EE WAS CLIMBING UP THE STEPS TO THE 1 BELT, 2 BELT TRANSFER BOX. HE WAS CARRYING HIS BREAKFAST IN HIS LEFT HAND AND TOOLS WEIGHING 50 & LBS. IN HIS RIGHT HAND. HE PROCEEDED TO STEP UP ON THE F IRST STEP WITHOUT THE USE OF HAND RAILS. WHEN HEDID HE FELT A SHARP PAIN IN HIS LOWER BACK.

EMPLOYEE WAS DISMOUNTING FROM THE CAB OF A K914 BACKHOE, USING THREE POINTS OF CONTACT. HE PLACED HIS LEFT FOOT ON A PILE OF LOOSE GRAVEL WHICH HAD BUILT UP AROUND THE TRACKS. AS HE PUT THE WE IGHT OF HIS BODY ON HIS LEFT FOOT, THE PILE GAVE WAY CAUSING HIS FOOT TO TURN OVER.

THE EE WAS HOLDING A CABLE IN HIS HANDS WHICH WAS USED TO UNSCREW THE TELESMITH 44FC CRUSHER. THE LOADER OPERATOR TIGHTENED THE CABLE WITHOUT THE EE S KNOWLEDGE.

WHILE TIGHTENING BOLTS ON CRUSHER WITH HAMMER AND WRENCH, 1ST PARTY HOLDING WRENCH, 2ND PARTY SWINGING HAMMER, THE HANDLE HIT OFF HIS BODY SENDINGTHE HAMMER INTO VICTIM'S HAND, RESULTING IN AV ULSED FINGER TIP.

VICTIM WAS CHECKING DOOR ALIGNMENT AFTER INSTALLING NEW HINGES AND LATCHES. HE WAS CLOSING DOOR TO CHECK ALIGNMENT WHILE RESTING HIS HAND ON EQUIPMENT TO SUPPORT HIMSELF. DOOR CAUGHT TIP OF 3R D FINGER, 3RD JOINT.

85049OVE TRUCK OVER POTHOLE AND HURT BACK.

EMPLOYEE WAS USING OXYACETYLENE TORCH TO CUT A BOLT HOT SLAG FELL INTO SHOE EMPLOYEE WAS WORKING SYNTHETIC FIBRE SOCKS MATERIAL MELTED CAUSING A BURN TO HIS ANKLE

EMPLOYEE WAS CHECKING GREASE LEVEL IN GYRATOR CRUSHER. SOME GREASE GOT ON WORK PLATFORM. EMPLOYEE SLIPPED ON GREASE. TO KEEP FROM FALLING, HE PLACED A LOT OF STRESS ON LEGS, WHICH CAUSED HERNI A. AT THE TIME, EMPLOYEE REPORTED INJURY, BUT DECIDED NOT TO SEEK MEDICAL HELP. PAIN INTENSIFIED UNTIL 7-23-90 WHEN HE WENT TO CLINIC. LOST TIME BEGAN ON 7-27-90 WHEN EMPLOYEE WAS TOLD BY DOC

EMPLOYEE CLIMBED ONTO THE ENGINE HOOD OF A CAT 988B LOADER TO REACH A GREASE FITTING ON ANOTHER PIECE OF EQUIPMENT. HE PULLED HIMSELF UP USING HIS LEFT ARM ONLY. IN DOING SO, HE SPRAINED A SHO ULDER MUSCLE. EMPLOYEE WEIGHS ABOUT 400 POUNDS.

EMPLOYEE LOOKED OVER SHOULDER AS HE BEGAN TO BACK A 50 TON EUCLID HAUL TRUCK. HE FELT A "CATCH" IN HIS NECK. LATER DIAGNOSED AS A STRAIN.

EMPLOYEE WAS MOVING ROCKS WITH A FRONT-END LOADER AS HE MOVED THE LOADER FORWARD A ROCK FELL FROM THE BUCKET THE LOADER TIRE ROLLED OVER THE ROCK THE RESULTING MOTION JERKED THE EMPLOYEE FROM SIDE TO SIDE CAUSING THE INJURY EMPLOYEE DID NOTREPORT INJURY UNTIL 05-09-90 WHEN HE FINALLY SOUGHT MEDICAL TREATMENT

MOVING ROCK FROM ROAD SPRAINED BACK ROCK SLIPPED

PREPARING TO SECURE A TRUCK BED, HE LIFTED A WOODEN BLACK WEIGHING 40-50 POUNDS. THEN HE TURNED HIS BODY. A SHARP PAIN WAS FELT. HE SOUGHT MEDICAL HELP ON 1-6-90. CONDITION WAS DIAGNOSED AND T EMPORARY TOTAL DISABILITY BEGAN ON 1-9-90.

EMPLOYEE WAS LOADING LARGE STONE, INTO A TRUCK WITH FRONT LOADER. CUTTING DREDGE OF BUCKET STRUCK A ROCK STICKING UP FROM FLOOR OF PIT RESULTING IN JAR TO MACHINE BOUNCED HIM AROUND IN THE SEA T CAUSING AN OVEREXTENSION OF HIS LUMBAR MUSCLE.

EMPL WAS CHANING DRILL BIT APPARENTLY HE OVER EXTENDED WRIST AS HE WAS MOVING BIT.

EMPL HELPING REPAIR A CRUSHER MOTOR DRIVE BELT.EMPL GOING UNDER CATWALK OVEREXTENDED HIS KNEE.1ST DAY OF LOST TIME-8-10-89.

EMPL WAS DISMOUNTING FROM A KOBELCO K-975 SHOVEL HE SLIPPED ON AN OILY SURFACE HIS ARM STRUCK A SHARP PIECE OF METAL RESULTING IN A LACERATION

EMPL STEPPING OFF DOZER BLADE ARM TO GROUND.STEPPED ONTO DIRT CLOD AND TWISTED HIS ANKLE.

EMPLOYEE WAS IN EQUIPMENT SHOP TRYING TO DISLODGE A TAPERED PIN IN THE FRONT END SUSPENSION OF A EUCLID HAUL TRUCK. HE WAS STRIKING THE PIN FROM THE BOTTOM WITH AN 8-POUND HAMMER. AFTER THE PI N BECAME LOOSE, HE HIT IT AGAIN CAUSING IT TO FLY OUT AND STRIKE HIM ON THE HAND.

EMPLOYEE WAS GREASING PULLEY BEARINGS. WHILE MOVING TO ANOTHER LOCATION, HE SLIPPED AND FELL. GROUND WAS WET.

EMPL IN PRONE POSITION INTERMITTENTLY USING AIR WRENCH HELPING TO CHANGE GRIZZLEY BARS.OVEREXTENDED HIS LEG BRACING HIMSELF.HAD SUFFERED TORN LIGAMENTS IN SAME KNEE 5 MOS EARLIER.TORN LIGAMENT S WERE SURGICALLY REPAIRED BEFORE HE CAME TO WORK FOR THIS COMPANY.

EMPL WAS USING POCKET KNIFE TO CUT PIECE OF HOSE. HE CUT TOWARD HIMSELF. KNIFE SLIPPED & CUT HAND. NO GLOVES WERE BEING WORN.

EMPLOYEE STEPPED ONTO A TRAILER WHICH HE WAS LOADING.HE SLIPPED AND HIT SHIN CAUSING A MONOR PUNCTURE WOUND.HE FAILED TO REPORT ACCIDENT OR SEEK FIRST AID.WOULD BECOME INFECTED.HE SOUGHT MEDIC AL ATTENTION ON 07-20-88.MANAGEMENT DID NOT BECOME AWARE OF PROBLEM UNTIL MEDICAL BILLS WERE RECEIVED.

EMPLOYEE WAS OPERATING A CAT D7E TO FEED PUG MILL.HYDRAULIC LINE BROKE CAUSING FIRE.EMPLOYEE FEARED DOZER WOULD EXPLODE AND JUMPED.EMPLOYEE IS OVERWEIGHT AND HAS A BAD LEG AS A RESULT OF EARLI ER AUTO ACCIDENT.

EMP. WAS WALKING ON LEVEL DRY, SOLID GROUND. HIS KNEE BUCKLED UNDER HIM CAUSING AND OVEREXTENSION OF T HE KNEE JOINT. THIS RESULTED IN A SPRAIN. EMP. SAID HE DID NOT SLIP, TRIP, FALL IN HOLE , ETC.

EMP WAS LIFTING OBJECT 5 TO 25 LBS, USING BACK MUSCLES INSTEAD OF LEGS. SOMETIME DURIN THE DAY HE STRAINED A BACK MUSLCE WHICH LATER CAUSED MUSCLE SPASMS

EMPLOYEE WAS CO5LECTING INTO FROM DATA PLATE ON ELECTRIC MOTOR. HE PLACED HAND ON PULLEY GAURD. AS HE SHIFTED HIS WEIGHT, HE GRASPED GAURD FOR SUPPORTS BACK SIDE OFF, PULLEY WASNOT GUARDED. BE LT CAUGHT FINGE9 AND PULLED IT INTO THE PULLEY.

EMPLOYEE WAS LOADING BIN LEGS ON TO A FLAT BED TRAILER. THE BAR HE WAS USING TO ASSIST HIM, SLIPPED AND STRUCK HIM ON THE RIGHT KNEE.

EMPLOYEE WAS CL3MBING HOME-MADE LADDER WHICH SHIFTED CAUSING HM TO LOSE BALANCE. IN CATCHING HIMSELF HE HURT SHOULDER. HE REPORTED ACCIDENT BUT ID NOT BELIEVE MEDICAL ATTENTION WAS NECESARY. O N 1- -88 EMPLOY9E REPORTED INCREASED PAIN. HE WAS TAKEN TO EMERGENCY MEDICAL FACILITY. EXAM MADE BUT NO TREATMENT GIVEN. PAIN DID NOT SUBSIDE. LOST TIME BEGAN ON 1-21-88.

EMPLOYEE WAS HO5DING LIGHT TO ILLUMINATE WORK AREA WHERE ANOTHER EMPLOYEE WAS WELDING.INJURED EMPLOYEE WAS NOT WEARING EYE PROTECTION.

EMP AND ONE OTH9R WERE REMOVING A NUT WITH A 36" ASJUSTABLE WRENCH WITH 36" LONG PIPE ON HANDLE TO IMPROVE LEVERAGE. HE WAS BENEATH WRENCH & HANDLE BROKE AND HIT HIM ON HEAD

EMPLOYEE WAS CU7TING WITH A UTILITY KNIFE. THE KNIFE SLIPPED , CUTTING LEFT HAND, SUTURES APPLIED.

EMPLOYEE WAS OE1RATING STOCK TRUCK ON MINE ROAD. AT A CURVE HE SWERVED TO AVOID HITTING AN ONCOMING VEHICLE. THE TRUCK HAD ROLLED OVER. APPARENTLY THE STEERING WHEEL SPUN CAUSING THE PERSONAL INJURY. 3

EMPLOYEE WAS OP9RATING A CAT. 992A FRONT LOADER. HE STOPPED LOADER AND STEPPED ONTO ONE OF THE REAR, TIRES TO TALK TO A HAUL TRUCK OPERATOR. WHILE RETURNING TO THE LOADER CATWALK, HE TRIPPED O R SLIPPED AND S7RUCK HIS KNEE ON AN AREA THAT WAS INJURED YEARS AGO. NO LOST TIME WHEN ACCIDENT OCCURRED. LOST TIME WILL BEGIN ON 10-27-87 WHEN HE IS SCHEDULED FOR SURGERY TO REPAIR DAMAGED C

EMP WAS ADJUSTI3G WATER ON THE 1ST BELT UNDER CONE. A ROCK FELL FROM SHAKER LACERATING R HAND, WHICH REQUIRED 7 SUTURES

EMPLOYEE SLIPPE8 AND FELL WHILE DISMOUNTING EUCLID END DUMP.EMERGENCY ROOM PHYSICIAN SAID HE HAD A CONTUSION AND SENT HIM ABCK TO WROK.NEUROLOGICAL SYSTEMS BEGAN TO APPEAR A WEEK LATER.ADDITIO NAL VISIT TO DO7TOR-REVEALED PINCHED NERVE BETWEEN VERTEBRAE C-6 AND C-7.LOST TIME BEGAN ON 09-21-87.ACCIDENT ORIGINALLY CALSSIFIED AS "FIRST AID".

WHILE CHECKING 2IL IN LOADER EMPLOYEE OPENED COMPARTMENT DOOR AND PULLED HIS SHOULDER CAUSING A TORN LIGAMENT AFTER CONSULTING WITH HIS SUPERVISOR EMPLOYEE DECIDED NOT TO SEEK MEDICAL TREATMNE T AFTER 4 WEEKS3PAIN HAD NOT SUBSIDED SO EMPLOYEE GOT MEDICAL TREATMENT

EMPLOYEE USED A3SOLVENT WITHOUT USING THE RUBBER GLOVES WHICH WERE PROVIDED. A SKIN RASH OCCURRED ON BOTH HANDS REQUIRING MEDICAL ATTENTION.

EMPLOYEE WAS SE7TING UP PORTABLE PLANT WHILE PUTTING PORTABLE BIN IN PLACE HE SLIPPED CATCHING HIS THUMB IN PORTABLE BIN WHICH RESULTED IN A BROKEN THUMB

EMPLOYEE WAS ON9 ELEVATED CATWALK WHEN HE STEPPED ON AN EXTRANEOUS PIECE OF STEEL LEFT ON CATWALK. EMPLOYEE DID NOT PAY ATTENTION TO WHERE HE WAS STEPPING.

OPERATING A CRA3E AND WAS BEE STUNG

I.NAME WAS WORK3NG ON AN ELECTRICAL PROBLEM AND STRUCK HIS LEFT KNEE ON THE SIDE OF THE CATWALK

HE WAS USING A 9OPE TO PULL A BUCKET OF COAL WHEN THE PLANT AND HAD A SHARP PAIN IN HIS LOWER BACK.

EMPLOYEE WAS P6TTING PLATE ON SHAKER SCREEN UNIT THE PLATE FELL CUTTING RT LEG REQUIRED SUTURES

GETTING OUT OF 5 DJ3 HAULAGE TRUCK AND SLIPPED ON THE STEP TWISTING HIS LEFT KNEE

I NAME WAS CLEA3ING MATERIAL FROM UNDER THE C-UNIT BIN,IN THE PROCESSHE APPLINED PRESSURE ON THE LOADER BUCKET CAUSING THE FRONT OF THE MACHINE TO RISE STRUCK THE BIN GATE.THE IMPACT CAUSED I NAME TO BOUNCE 5ROUND INSIDE THE CAB.LATER IN THE DAY HIS BACK STARTED HURTING HIM.

EE WAS OPERATIN1 A BOBCAT LOADER. EE CAUGHT HAND IN T HE BUCKET MECHANISM CAUSING A BAD BRUISE OF RIGHT HAND.

I.NAME WAS HELP3NG IN THE REPAIR OF A SHOVEL. IN THE PROCESS OF THE REPAIR HE WAS HELPING REPLACE A STEEL PLATE 3' X 4' AND WEIGHT 150 LBS. AND FELT PAIN IN HIS LOWER BACK

HE WAS A CUTTER3ASSISTING A WELDER AND INADVERTEDTLY LOOKED AT THE WELDING ARC.

I.NAME WAS CLEA3ING A PUGMILL FEEDER WITH THE FOXX DOOR UNLATCHED, SOME MATERIAL ROLLED DOWN THE FEEDER PAN STRIKING THE DOOR, CAUSING THE DOOR HANDLE TO FLY UP AND STRIKE HIM. THE HANDLE STRU CK HIM IN THE M2UTH LACERATING HIS LOWER LIP. CHIPPED TWO TEETH AND REQUIRED ONE STITCH

I.NAME CHECKING GENERATOR BELT ON SHOVEL WITH MOTOR OFF.HIS HELPER INADVERTENTLY ACTIVATED STARTER CATCHING I.NAME FINGER BETWEEN BELT AND PULLEY.HE WAS TAKEN TO ACCESS WITH TIP OF MIDDLE FING ER CUT OFF AND BROKEN.TREATED AND TOLD TO SEE ANOWN DR.RIGHT HAND.

I.NAME WAS GETTING OUT OF THE CRANE AND STEPPED ON THE TRACK AND SLIPPED AND FELL. HE WENT TO THE DOCTOR ON 10-8-85 AND WAS TOLD HE WAS ONLY BRUISED ON 10-15-85 HE WENT TOACCESS AND HAD X-RAYS TAKEN AND WAS TOLD HE HAD A BROKEN TOE AND A POSSIBLE SLIPPED DISC. WENT TO HIS DOCTOR AND WAS TOLD TO RETURN ON 10-22-85.

WORKING ON PLANT AND GOT PAIN IN ABDOMINAL AREA.WENT TO DR 6-27 AND WAS TOLD HE HAD A HERNIA AND NEEDED AN OPERATION.

GETTING DOWN LADDER OF LOADER & HIT ARM,CHIPPING BONE.

MAKING ADJUSTMENT ON A SHOVEL WHILE IT WAS RUNNING HOIST DRUM RAKED ACROSS BACK OF RT HAND CUTTING IT HAD TO HAVVE STITCHES

SHOVELING MUD. WENT TO THROW OVER RT. SHOULDER & PULLED MUSCLE.

GETTING UP TRACK OF CRANE, SLIPPED, & PULLED CHEST MUSCLE.

GREASING LOADER.JUMPED DOWN FROM TIRE AND PULLED LIGAMENTS IN LEFT FOOT AND ANKLE.

GETTING UP ON MACK TRUCK & BUMPED LEFT KNEE. INJURY DID NOT BEGIN TO BOTHER HIM UNTIL 11-06-84 WHEN IT BECAME RED & SWOLLEN. WENT TO DOCTOR ON 11-06-84.

USING GRINDER & CUT BETWEEN KNUCKLES ON LEFT HAND.

INJURED WAS STANDING WITHIN THE SWING RADIUS OF THE HOPPER CRAME WHEN THE CRANE WAS SWUNG AROUND AND STRUCK HIM IN THE BACK.

CUT ON RT FOREARM BY FLYING ROCK AT THE PRIMARY. HAD 3 STITCHES.

PICKING UP ROCKS AROUND EUCLID WHEN ONE BOUNCED OFF SIDE OF TRUCK AND STRUCK RT LEG AND FELL ON RT FOOT BRUISING AND MAHSING IT

POWER STEERING HOSE BROKE ON EUCLID & SHE COULDN\T STEER IT. EUCLID WAS NEAR HIGHWALL & SHE THOUGHT IT WAS GETTING READY TO GO OVER ITI SO SHE JUMPED OUT CAUSING BOTH LEGS TO LOCK UP & BRUIS ING THEM.

OPERATING EUK WHEN SHOVEL SWUNG AROUND WITH A BUCKET OF ROCKS, A ROCK FELL THRU WINDSHIELD, HIT DASH AND BOUNCED BACK AND HIT EMPLOYEE IN RT. EYE.

PUTTING IN PUMP AND DIRT BLEW IN RT EYE EYE BECAME INFECTED

PUTTING UP SHED, DRILLING HOLES, CAUSED PRESSURE ON VERTABRA, PINCHING NERVE IN BACK.

INJ WAS OPERATING A SHOVEL LOADING A TRUCK WHEN BOLT BROKE THAT WAS HOLDING A HOIST SHAFT BEARING ALLOWING SHAFT TO RISE PUTTING PRESSURE ON HOIST BRAKE CAUSING HOIST BRAKE PEDAL TO SNAP BACK BREAKING RT ANKLE

PIECE OF SLAG IN LEFT EYE.

PULLING ELECTRICAL WIRE AND HURT RIGHT SHOULDER.

DUMPING CEMENT ON BELT WITH METAL TRASH CAN & SCRAPED R HAND ACROSS TOP & PALM. NEEDED TO BE CLEANED UP & GOT TETANUS SHOT

CARRYING TRANSFORMER AND DROPPED ON RIGHT FOOT BREAKING IT

CARRYING AN 8X8 AND HURT BACK

GETTING DOWN OUT OF CRANE STEPPED ON ROCK AND TWISTED LEFT ANKLE

USING WEEDEATER AND OBJECT FLEW UP AND HIT HIM IN HEAD NEEDED XRAYS AND 2 STITCHES

INJURED WAS WORKING ON A SHOVEL AND CHAIN SLIPPED TEARING SKIN OFF LEFT HAND AND IT BECAME INFECTED

EMPLOYEE WAS WELDING ON THE TOP SECTION OF A BOX ONTHE PLANT HE WAS STANDING ON A TEMPORARY LADDER AS HE TURNED TO GET ANOTHER WELDING ROD THE LADDER SLIPPED THE EMPLOYEE FELL APPROX 20FT STRI KING A LEDGE ON THE WAY TO THE BOTTOM OF THE BOX CAUSING A DISLOCATION OF THE RT HUMERUS AND CHIPPING THE PROXIMAL CAP OF SAME

INJURED WAS CLEANING BELT OFF AND STRUCK LEFT SIDE ON HANDRAIL CRACKING 10TH RIB IN LEFT SIDE