Crown III Mine: 1 muerte registrada Coal

WHILE HELPING SEVERAL PEOPLE HANG A SECTION OF 7200 HV CABLE EMPLOYEE FELT A PAIN IN HIS LOWER BACK.

WHILE LOADING THE TIMBER TRUCK WITH PROPS EE FELT A POP IN HIS LEFT SHOULDER.

WHILE ROOF BOLTING A PIECE OF COAL FELL STRIKING EE IN THE RIGHT CHEEK BONE JUST BELOW THE EYE.

EE WAS PUSHING A RAMCAR TO THE CHARGING STATION WITH HIS RAM HIS BUMPER WENT UP ON THE TAIL GATE THEN DROPPED SLAMMING HIS HEAD INTO THE CANOPY.

WHILE TRAVELING DOWN THE NSM TRAVEL WAY EMPLOYEE CAME UPON A ROOF FALL IN THE TRAVEL WAY AT X-CUT 44.

A roof fall approximately 20'x 16' by 6' high was found by mine examiner in the North SubMain in Entry 10 between crosscuts 4 and 5. No harm to personnel or equipment was experienced.

Near the end of his shift on 5/24/12, Employee stepped in uneven mine floor in an outby area and hurt his left ankle and foot, and his right knee. Employee did not fully report incident until 5/29/12. Employee did not begin missing work due to the injury until 06/06/2012.

Miner was preparing to move tracking system reader. When he cut the wire to the reader, the reader swung down and struck him in the face/mouth - striking his teeth. Employee did not miss work until June 8 thru 13, 2012.

AT APPROX. 2:20 AM A ROOF FALL WAS FOUND IN THE NORTH SUB-MAIN TRAVELWAY X-CUT 23.

WHILE STANDING IN THE WASH HOUSE A BASKET FELL STRIKING EMPLOYEE ON THE HEAD.

WHILE MAKING THE WEEKLY EXAM A FALL WAS DISCOVERED IN THE MAIN WEST RETURN AT X-CUT 3 ENTRY # 2.

WHILE MAKING HIS WEEKLY EXAMINATION OF THE RETURNS THE EXAMINER CAME UP ON A FALL IN THE NORTH SUB-MAIN RETURN AT X-CUT 12 ENTRY # 1.

At approx.11:30 pm repairman found a fall in the 9th north between x-cut 85 and 86 entry # 3 and reported it to his mine manager.

While going back to abate an area under citation,EE found a fall at xc 46 entry # 11 return of the north sub-main.

WHILE MAKING HIS WEEKLY EXAMINATION A FALL WAS FOUND IN THE MAIN WEST RETURN AT X-CUT 119 ENTRY # 2

WHILE MAKING HIS EXAM.A ROOF FALL WAS FOUND IN THE MAIN-WEST SOUTH RETURN AT X-CUT 91 # 11 ENTRY. THE FALL WAS REPORTED AND ALL ENTRIES TO THE FALL WERE PROPPED OFF WITH A DOUBLE ROW OFF PROPS.

WHILE MAKING THE WEEKLY RETURNS THE EXAMINER FOUND A ROOF FALL IN THE NORTH SUB-MAIN RETURNS X-CUT 86 #3 ENTRY. ALL ENTRIES TO THE FALL ARE TO BE DANGERED OFF WITH TWO ROWS OF PROPS.

WHILE MAKING THE WEEKLY RETURNS THE EXAMINER FOUND A ROOF FALL IN THE MAIN-WEST RETURNS AT X-CUT 78 # 12 ENTRY. ALL AREAS TO THE FALL ARE TO BE DANGERED OFF WITH TWO ROWS OF PROPS.

WHILE MAKING THE WEEKLY RETURNS THE EXAMINER FOUND A ROOF FALL IN THE MAIN-WEST RETURNS AT X-CUT 77 ENTRY # 12. ALL AREAS TO THE FALL ARE TO BE DANGERED OFF WITH TWO ROWS OF PROPS.

WHILE MAKING THE WEEKLY RETURNS THE EXAMINER FOUND A ROOF FALL IN THE MAIN-WEST RETURNS AT X-CUT 37 ENTRY # 2. ALL ENTRIES TO THE FALL ARE TO BE DANGERED OFF WITH TWO ROWS OF PROPS.

WHILE MAKING THE WEEKLY RETURNS THE EXAMINER FOUND A ROOF FALL AT X-CUT 35 ENTRY # 4. ALL ENTRIES TO THE FALL ARE TO BE DANGERED OFF WITH TWO ROWS OF PROPS.

While cutting the outer jacket off the bolter cable his razor knife slipped cutting his left thumb.

A ROOF FALL WAS FOUND IN THE MAIN WEST ENTRIES BETWEEN # 5 AND # 6 Entries. A K order was issued and a plan was agreed upon to start renovating the fall area.

AT APPROX. 9:45 PM ON 11/20/11 A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE AT X-CUT 89 BETWEEN ENTRIES 8 AND 9 ALL APPROACHES TO THE FALL WERE PROPPED AND CRIBBED.

AT APPROX. 7:30 PM 11/20/11 A ROOF FALL WAS FOUND IN THE MAIN WEST RETURN AT X-CUT 88 ENTRY # 11. ALL APPROACHES TO THE FALL WERE PROPPED AND CRIBBED.

AT APPROX.9:45 PM ON 11/20/11 A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE BETWEEN X-CUT 70 AND 71 IN ENTRY # 9 ALL APPROACHES TO THE FALL WERE PROPPED AND CRIBBED.

AT APROX 7:45 PM A FALL WAS FOUND IN THE MAIN WEST RETURN AT X-CUT 72 IN ENTRY # 12 ALL ENTRIES TO THE FALL WERE PROPPED AND CRIBBED.

AT APPROX.10:20 AM A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE AT X-CUT 104 #7 ENTRY. ALL APPROACHES TO THE FALL WERE PROPPED AND CRIBBED. THE ORDER WAS LIFTED IN THIS AREA ON 11/21/11.

WHILE GETTING OUT OF HIS RAM CAR EE TRIPPED LANDING ON HIS LEFT ANKLE-LOWER LEG.

WHILE OPERATING THE MINER IN A TURN THE RIB ROLLED STRIKING THE BACK AND SIDE OF HIS LEFT LOWER LEG.

WAS TRAVELING OUT OF THE MINE A THE END OF THE SHIFT EMPLOYEE STRUCK HIS HEAD ON A LOW ROOF BOLT.

EE TRIPPED OVER A PIECE OF CURTAIN. WHILE TRYING TO BREAK HIS FALL HE PUT HIS HANDS OUT BREAKING HIS LEFT RING FINGER.

WHILE STEPPING OUT OF A DIESEL 5-MAN HE SLIPPED ON A PC. OF COAL STRAINING HIS UPPER LEFT THIGH.

WHILE STANDING NEXT TO THE BOLTER A PIECE OF ROCK FELL STRIKING EMPLOYEE ON THE HEAD SHOULDER AND RIGHT ARM.

AT APPROX. 4:45 AM A FALL WAS FOUND IN THE NSM RETURN AT ENTRY # 3 AT X-CUT 61. A STOPPING WAS DAMAGED AS A RESULT OF THE FALL. A J ORDER WAS ISSUED AND LATER MODIFIED TO A K ORDER TO ALLOW US TO PROP ALL 4 SIDES TO THE FALL, BUILD A CRIB ON THE TRAVELWAY AND THEN RESTORE VENTILATION. THE FALL MEASURED APPROX. 25FT. IN LENGTH, 20FT. WIDE AND 9FT. HIGH.

WHILE TRYING TO LOOSEN A FITTING ON THE MINER USING TWO WRENCHES THE WRENCHES SLIPPED SMASHING HIS RIGHT RING FINGER.

WHILE TRAVELING DOWN THE TRAVELWAY A PIECE OF ROCK FELL STRIKING EE ON THE BRIDGE OF THE NOSE AND THE RIGHT CHEEK

A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE # 8 ENTRY X-CUT # 94 AT APPROX. 6:43 AM MSHA WAS NOTIFIED. PROPPED AND CRIBBED ALL APPROACHES TO THE FALL PER INSPECTOR INSTRUCTIONS.

WHILE ROOF BOLTING A PIECE OF ROCK FELL STRIKING EE ON THE BACK OF HIS HEAD.

WHILE ROOF BOLTING A PIECE OF ROCK FELL STRIKING EE IN THE MOUTH AND RIGHT ARM.

Employee received treatment for Repetitive trauma, bilateral upper extremities, carpal/cubital tunnel/overuse syndrome on 4/20/2012.

WHILE ROOF BOLTING A PIECE OF ROCK SLID DOWN THE AUGER STRICKING EMPLOYEE IN THE FOREHEAD.

WHILE REMOVING A PC OF ROCK FROM OFF THE TOP OF THE MINER PINCHED HIS FINGERS BETWEEN THE ROCK AND THE ROOF.

WHILE PULLING A ROOFBOLT AUGER OUT OF THE HOLE A PIECE OF ROCK FELL GLANCING OFF THE BOLTER ARM STRIKING EMPLOYEE ON THE HEAD NECK AND BOTH SHOULDERS.

AT APPROX. 1:00 AM THE EXAMINER FOUND A ROOF FALL IN # 1 ENTRY X-CUT # 141 OF THE MAIN WEST ENTRIES.

A roof fall occurred at in Entry #5 (belt entry)in the North Submain of the Main West.

A ROOF FALL WAS FOUND IN ENTRY 3 X-CUT-45 IT WAS 25 FT. LONG 20FT. WIDE AND 8FT. HIGH. THE FALL WAS PROPPED ON ALL FOUR SIDES AN ADDITIONAL CRIB WAS BUILT ON THE TRAVELWAY SIDE.

WHILE PULLING OUT AN AUGER A PIECE OF ROCK FELL STRIKING HIS LEFT HAND

A REPAIRMAN WAS IN THE 2ND SOUTH INTAKE CHECKING THE PHONE LINES WHEN HE CAME UP ON THE FALL AT X-CUT 22 ENTRY 6 AND REPORTED IT AT ONCE TO HIS SHIFT MINE MANAGER.

AT APPROX. 2:45 AM ON THE MORNING OF 03/08/11 THE AIR BRAKE VALVE THAT OPENS AND CLOSES THE BRAKES ON THE HOIST FAILED. THE REPAIR TOOK APPROX. 50 MINUTES.

WHILE DOING PERMISSIBILITY ON # 34 MINER CABLE A PIECE OF ROCK FELL SMASHING HIS RIGHT HAND.

EMPLOYEE TRIPPED OVER A ROCK DUST HOSE WHILE DUSTING IN THE INTAKE. THIS ACCIDENT WAS DISPUTED FOR SEVERAL WEEKS BEFORE IT WAS DETERMINED TO BE A NON-WORK RELATED INJURY. THIS WAS NOT MSHA REPORTABLE.

While moving material on the roof bolter, a piece of rock fell striking him on his left hand. The impact of the rock broke his left pinky finger.

While lowering a belt drive the ratchet handle slipped, cutting a finger on his right hand. The injury resulted in sutures and no lost work days.

EMPLOYEE STEPPED OUT OF A MINITRACT HIS FOOT GOT HUNG UP AND HE FELL ON HIS BACK.

WHILE REMOVING A COVER ON 32 CM TO FIX A WATER LEAK THE COVER FELL ON DARRELLS RT. FOOT.

WHILE EXAMINING IN UNIT 2 EE STEPPED IN A RUT FRACTURING A BONE IN HIS FOOT.

WHILE REACHING FOR A ROOF PLATE A PC. OF ROCK FELL CUTTING HIS RIGHT MIDDLE FINGER.

WHILE BOLTING A CORNER ON THE 2 ND WEST TRAVEL WAY A PIECE OF ROCK FELL HITTING HIM IN THE FOREHEAD.

While hanging feeder power cable from roof, employee heard a "pop" and felt pain in his right shoulder. The employee subsequently had surgery on February 3, 2011, which was deemed "worked-related" by the attending physician. Because the employee was able to work for three months, this case was disputed. The employee returned to work on full duty status on April 18, 2011.

WHILE BOLTING A PIECE OF ROCK FELL BETWEEN THE PINS STRIKING THE TOP OF HIS RIGHT FOOT.

While plugging the battery plug into the scoop he hit his head on the jumper cable causing it to fall crushing his finger between the jumper cable and the battery plug.

AT 7:00 PM 09/27/10 A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE ENTRY # 8 1 X-CUT OUTBY ZERO X-CUT. ALL ENTRIES TO THE FALL WERE PROPPED AND CRIBBED.

On the above date, employee was diagnosed with repetitive motion syndrome of the left upper extremity and believes it is work-related. No incident occurred that resulted in this condition. Th e illness was disputed until now.

AT APPROX. 5:00PM 09/20/10, A ROOF FALL WAS FOUND IN THE NORTH SUB-MAIN INTAKE ENTRY #7 X-CUT #21.

AT 1:10 AM A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE ENTRY # 8 X-CUT 118.

EMPLOYEE TRIPPED WHILE GETTING INTO A MANTRIP, STRAINING HIS LOWER BACK AND LEFT HIP.

A ROOF FALL WAS FOUND AT X-CUT 99 OF THE MAIN WEST TRAVELWAY. ALL ENTRIES TO THE FALL WERE PROPPED AND CRIBBED. CLEAN UP HAS BEGAN PER OUR APPROVED CLEAN UP PLAN.

WHILE BOLTING, TOP FELL BETWEEN THE PINS, STRIKING HIS LEFT SHOULDER.

WHILE MINNING COAL AT THE FACE A PIECE OF COAL FELL BETWEEN THE PINS CRUSHING HIS LEFT FOOT.

A ROOF FALL WAS FOUND IN THE MAIN WEST INTAKE X-CUT 118. THE PRIMARY ESCAPEWAY WAS REROUTED AND ALL ENTRIES TO THE FALL WERE PROPED OR CRIBBED.

WHILE SHOVELING ALONG THE NORTH SUB-MAIN BELT EMPLOYEE FELT A PAIN IN HIS BACK.

While examining the faces, a piece of rock fell between the pins striking him on the right shoulder and right foot.

WHILE OPERATING THE MINER A PIECE OF ROCK FELL BETWEEN THE PINS STRIKING HIM ON THE HEAD AND SHOULDERS.

EE WAS GOING THRU A MAN DOOR THE WIND BLEW HIS HARD HAT OFF WHEN HE STOOD UP HE STRUCK HIS HEAD ON A ROOF BOLT

WHILE REMOVING THE BOLTER WRENCH FROM A BOLT THE WRENCH KICKED BACK STRICHING HIM IN THE MOUTH.

A ROOF FALL WAS FOUND IN THE UNIT 1 TRAVELWAY AT X-CUT # 7. OUR PLAN IS TO REROUTE THE TRAVELWAY, AND ALL ENTRIES TO THE FALL WILL BE PROPPED AND CRIBBED.

WHILE EXAMING THE NSM BELTLINE HE TRIPPED AND FELL FOWARD ON HIS LEFT ARM AND WRIST.

WHILE BOLTING, A PIECE OF ROCK FELL, DRIVING HIS HARD HAT INTO HIS GLASSES THEN INTO HIS NOSE.

EMPLOYEE WAS LIFTING A CAN OF OIL AND ALLEGEDLY FELT PAIN IN HIS RIGHT SHOULDER.

EMPLOYEE WAS USING A SCREW DRIVER TO ALIGN A BELT SPLICE,THE SCREW DRIVER SLIPPED CUTTING LEFT HAND.

HE WAS INSTALLING THE FIRST PIN IN A ROW OF BOLTS HE HAD HIS LEFT HAND ON TOP OF THE CANOPY WHEN A PIECE OF ROCK FELL CRUSHING HIS HAND.

WHILE HANDLING SUPPLIES ON TOP OF SCOOP TRACTOR EMPLOYEE WAS STRUCK BY FALLING ROOF.

WAS PUTTING A BOARD ON A PLATE CAUGHT HIS FINGER BETWEEN THE ROOF AND THE PLATE.

UNHOOKING SUPPLY TRAM THE TRAM ROLLED AND HE TWISTED HIS LEFT ANKLE

WHILE DRIVING A RAM CAR DOWN THE TRAVELWAY HE RAN OVER A PIECE OF ROCK OR A PROP END BOUNCING HIS HEAD AND LEFT SHOULDER INTO THE CANOPY.

While unloading belt structure, stepped off tram and twisted his right ankle.

A pump motor was suspended by a come-a-long and was being pulled into position when the chain twisted pinching his rt ring finger.

A roof fall has occurred in unit #3 at crosscut #42 in entry #4. MSHA was notified at 0900 on December 31 2009. The area around the fall was re-supported and all approaches to the fall were propped. The travel way was also re-routed.

GETTING SUPPLIES OFF THE BACK OF BOLTER A PIECE OF SLATE FELL STRIKING THE BACK OF HIS HEAD.

THERE WERE TWO ROFF FALLS IN THE 2ND SOUTH MAIN WEST ONE AT X-CUT 82 # 3 entry AND ONE AT X-CUT 82 # 2 ENTRY PROPS ARE BEING SET AROUND THE FALLS AND ADDITIONAL 8FT BOLTS INSTALLED INBY THE FALLS.

Auger popped back, striking left thumb.

While taking the rub rail off of a miner, the rail fell striking the employee in the shin.

The employee had his hand on the tray of the roof bolter and a rock fell from the top, striking his hand.

Employee was putting two augers together, they weren't aligned properly and one of the augers sprung striking the employee's left thumb.

While hauling coal in a joy shuttle car, the operator struck the rib causing the rib to loosen and fall into the operators compartment, striking the operator.

WHILE STANDING NEXT TO THE MINER, PRYING A ROCK OFF, THE ROCK FELL ON TO HIS LEG AND FOOT. THE MINER WAS STANDING IN A MUD HOLE.

WHILE ROOFBOLTING A PIECE OF ROCK FELL OUT OF THE TOP STRIKING HIM IN THE BRIDGE OF THE NOSE AND ON THE RIGHT ANKLE.

WHILE BOLTING HAD HIS HAND ON THE CANOPY POST THE SPACER SLID DOWN PINCHING HIS FINGER

WAS CLEANING OUT PLANATARY ON MINER AND JAMMED HIS THUMB

WHILE WALKING BACK TO GET A PIN A PIECE OF ROCK FELL BETWEEN THE PINS AN STRUCK HIS BACK.

A ROOF FALL WAS FOUND IN UNIT #1 X-CUT 40 # 7 ENTRY.

ROOF FALL WAS FOUND IN UNIT #1 AT xc 42, ENTRY #8

A ROOF FALL WAS FOUND IN THE NORTH SUB-MAIN RT RETURN ENTRY #2 FOOTAGE #2283.

WHILE BOLTING, AUGER BENT, SLAPPING LEFT HAND.

A ROOF FALL WAS FOUND AT X-CUT 41 ENTRY # 8 MAIN WEST INTAKE.

PIECE OF ROCK FELL HITTING TOP OF LEFT FOOT

EE WAS PINNED BETWEEN THE BOLTER BUMPER AND THE RIB, CRUSHING HIS RIGHT LEG BELOW THE KNEE.

Employee, complaining of back pain, was transported out of mine to receive medical treatment. He made no claim or assertion that he was injured at mine at time of incident. Upon investigation, management determined that incident was not work-related. MSHA issued 1046 citation. This 7000-1 submission is to abate citation #6675934.

Employee was walking alongside the roofbolting maching, stepped on a chunk of coal and twisted his right ankle.

WHILE MAKING THE INTAKE INSPECTION, THE FALL WAS FOUND AT X-CUT 78 ENTRY #8 MAIN WEST INTAKE.

Employee was installing boards on props to protect SCSR storage area when a rib rolled over and fell, striking him on his back knocking him to the mine floor. The coal rib also struck his feet. He worked the next two scheduled shifts but started missing on April 14. His first Dr. visit was April 15 when a left foot fracture was found after xrays were taken.

Installing a curtain board on the mine roof with roof bolting machine, when on side operator pressured ATRS against roof, the floor jack pressed employees right foot into the mine floor. His right foot suffered a contusion from the middle to the distal end.

Employee was unpluging a battery from a ram car when he slipped and fell while standing on loose coal. His left thumb was cut when he fell. Three stitches were required to close the wound.

While washing a Roof Bolting Machine he stepped in a hole and twisted his left knee. He did not begin missing until April 2, 2009 after a surgical procedure was preformed on his left knee.

Employee was going through a 3x3 mandoor in a stopping when dust flew into his left eye. He finished the shift but was kept off work due to an abrasion on his left eye.

Unintentional roof fall, #78 crosscut #4 entry unit #3 North Submain. Length 25' width 18', height 8'. Fall propped all 4 sides, 4 way intersection. Date of development 1-5-09.

Employee was assigned to work on the conveyor belt. As he was traveling (walking) in a x-cut that contained muddy gob on the floor he slipped on a 3" water pipe and fell onto his buttock. He was taken by ambulance to a hospital and treated for a contusion.

Man was roof bolting, piece of top fell while he was drilling. Put his left hand up to protect himself and was struck on left hand and side of his face. Received abrasion to face and laceration to left hand. 2 stitches on hand.

Unintentional roof fall 11th Main West Entry at 0 x-cut on the bottom. Will be proped off from area people can walk. Length 25', width 15', height 8'. 4 way intersection. Approx date of mining June 2004.

Installing an 8 ft roof bolt, while straighting the bolt to install he slipped and strained his back.

Employee set lunch on skid on ground, raised up and bumped into roof bolt. Loose debris and one 6" flat coal piece rolled down back.

A roof fall occurred in the 2nd South in entry 3 at x-cut 18. The fall measured 20' long, 25' wide and 8 feet high. It did not cause injury, affect travel, ventilation or equipment. The fall will not be cleaned up.

Employee was backing a personnel carrier into a crosscut when the tongue of a wet duster struck and lacerated his left leg just below the outside of his knee. 12 stitches were used to close the wound.

Employee was operating the continuous miner loading a ram when a rib fell striking the employee on the back of his right leg and knocking him into the ram car. He continued to work until Nov 18, 08 until which time his physician began treating him for an infection in the affected area of his right lower leg.

A fall occurred in the 2nd west submain in entry #4 at X-cut #33. The fall measured 25' long, 30' wide and 7' high. The fall took out a stopping and caused some leakage. It did not affect travel, cause injury or damage equipment. The fall will not be cleaned up.

A roof fall occurred in the North sub main in entry #9 x cut12. The fall was 40ft long, 20ft wide and 8ft high. This fall did not cause injury, affect travel, ventailation or passage of people. The fall will be cleaned up.

While roof bolting the drill steel plugged up; once cleared we began to raise the drill steel to the roof. When the steel struck the roof a clod fell and the steel bent and snapped back striking his left hand.

A roof fall occurred in the 2nd south at X cut 6 in the entry #3. The fall measured 30ft long, 20ft wide and 81/2ft high. The fall did not cause injury, passage of people or ventilation. The fall will not be cleaned up.

Employee reported that he tripped and lost his balance when he fell and twisted his right knee.

A roof fall occurred in the 2nd South in entry #3. The fall measured 20' x 30' x 9'. The fall did not cause injury, affect travel, ventilation or passage of people. The fall will not be cleaned up.

While in the process of roof bolting, a piece of clod fell from the roof. As the miner was moving out of the way of the falling clod it struck him on the left elbow (posterior). His elbow was swollen and cut in two small places.

A roof fall occurred in the South Sub Main Entries xcut 33 in entry #12. The fall measured 25' wide, 25' long & 5' tall. It did not cause injury, affect ventilation or passage of people. No equipment was affected. It will not be cleaned up.

Occured in Main West, intake x cut 119 entry #8 fall measured 20'l x 20'w x 8'h. did not affect ventilation, travel on cause injury and will not be cleaned up.

Twisted left wrist. 2" water pipe fell of sled, while trying to reload, he twisted his left wrist. Did not begin missing until Jan 28, 2009 due to surgical procedure to repair the damaged wrist.

A roof fall occured in the South Sub Main, entry #3 at x-cut 40. The fall measured 20' wide x 20' long x 8' high. It did not affect ventilation travel or cause injury. The fall will not be cleaned up.

Employee was hit in the face with a piece of steel.

IE was working demolition of a steel structure at the bottom of the slope. He and another employee were torch cutting 8" channel iron into 36" long pieces. IE cut one piece off and set it down on the ground, leaning it up against the belt frame. Soon after, the piece tipped and fell against IE's lower rt leg, causing an approx 3" long laceration to his lower rt leg.

A roof fall occurred in the Main West entry #3 at 33 x-cut. The fall measured 20' long 20 feet wide & 8 feet high. It did not affect ventilation, travel or cause injury. It will not be cleaned.

A roof fall occured in the 3rd West panel at 24 x-cut in entry #4. The fall measured 22' L x 26' W x 10' High. It did not affect ventilation, travel or cause injury. It will not be cleaned up.

Struck on right leg with rock.

Employee burnt forearm while using torch.

EE walked around timber trip that was stuck and struck a roof bolt with her hard hat. She had a neck stain at the time and continued to work until 10/9/08, when she had surgery.

Employee was cutting bands on bundle of roof bolts, slipped and twisted foot causing strain.

A roof fall occurred in the South Sub Mains at 9Xcut in entery #7. The fall measured 25' long, 25' wide and 9' high. The fall did not affect ventilation, travel or cause injury. It will not be cleaned up.

Broken wire in trailing cable for hoist controls.

Rock fell from brow and struck employee, fracturing his pelvis, left femur and 2 left ribs.

EE was hit by rock on his lower back.

EE slipped and twisted left knee. EE continued to work until today 4/29/08, he will undergo surgery.

Employee was struck on left hand with a piece of steel, fracturing thumb.

A roof fall occurred in the south submain of 35 xcut in entry #11. The fall measured 20' long, 20' wide & 8' thick. The fall did not affect ventilation, travel or cause injury. It will not be cleaned up. No one is required to work or travel in this entry.

Employee smashed right thumb.

A roof fall occured in the 2nd south Sub Main at x cut 50 in entry #4. The fall did not affect travel, ventilation or cause injury. The fall measured 20' long, 18' wide and 9' high. It will not be cleaned up. No one is required to work or travel in the entry.

A roof fall occurred in unit 1 (1st west panel) in the rooms. It is located in return room 2 in the last open xcut. It measures 20 ft wide, 30 ft long & 7 ft thick. This fall did not affect ventilation, travel or cause injury. It will not be cleaned up. No one is required to work or travel in this entry.

A roof fall occurred in the return of the 3rd West panel. The fall is located in entry 8. It measures 20 ft long, 2 ft wide & 8 ft tall. It is at 11 x-cut. This fall did not affect ventilation, travel, or cause injury. It will not be cleaned up. No one is required to work or travel in this entry.

Employee sprained left ankle when he fell over metal laying on ground.

A roof fall occured in the return of the 2nd South submain entries. The fall measured 20 ft long, 25 foot wide and 8 foot high. It is located in #8 entry at 16 X Cut. This fall did not affect ventilation, travel or cause injury.

Employee cut finger on piece of metal requiring 5 stitches.

A roof fall occurred on the travelway of the 1st west panel, entry #6 at 41 x-cut. The fall did not affect ventilation, travel or cause injury. The fall was 25 ft long, 18 ft wide, & 10 ft high.

Employee was hit by top.

A roof fall occurred in the 1st West unit in entry #5 at footage station 3710. The fall did not affect ventilation, travel, or cause injury. The fall was 20 ft long, 20 ft wide & 8 ft high. The fall occurred on the section breaker feeder.

EE was standing in last open X-cut in unit. A piece of rock fell from between the bolts, striking him on back of head and neck.

a fall occurred in the 2nd south room 35 crosscut 1 the fall was 20' wide, 20 ' long, and 8' high. The fall didnt affect ventilation, travel, damage, equipment, or cause any injury. the area was bolted with 6' to 8' point anchor bolts. this was in worked out rooms, no one is required to work or travel in the area.

A roof fall occurred in the SSM intake aircourse in entry #8, xcut 38. The fall measured 20' wide, 20' long & 8' high. It did not effect travel, ventilation or cause injury. No one is required to work or travel in this area.

A roof fall occurred on the 3rd west belt 3 xcuts outby room #1. The fall was 35' long, 35' wide & 10' tall. It did not effect ventilation, cause injury or block travel.

Employee was bolting at the face. He moved to the rear of the bolter when a piece of shale fell directly in front of him striking him on the upper right foot.

Employee was moving roof plates around on roof bolter when one slid down cutting his right lower arm. He received 3 stitches.

A roof fall occured on the 2nd South belt at x-cut 19, entry # 5. The fall was 30' long, 25 ' wide and 8' high. It did not affect ventilation, cause injury or block travelway.

A roof fall occurred in the 2nd West Return in entry #1 at xcut 20. The fall was 20' long, 20' wide & 8' high. The fall did not affect ventilation, block travel or cause injury. No one is required to travel or work in this area.

A roof fall occurred in the 2nd West, entry #9, xcut 35. The fall was 20' long, 20' wide & 8' high. The area was bolted with 6 & 8' point anchor bolts. The fall did not affect ventilation, block travelway or cause injury. No one is required to travel or work in this area.

A roof fall occurred in the 2nd South submain entry #3 at 2170 footage station. The fall was 20 ft long, 20 ft wide, & 8 ft tall. The area was bolted with 6' & 8' point anchor bolts. The fall did not affect ventilation, block travelway or cause injury. No one is required to travel or work in this entry.

A fall occured in the 1st West panel, #5 entry, 18 crosscut. The fall was 20 foot long, 20 foot wide and 8 foot high. The area was bolted with 6' & 8' point anchor bolts. The fall did not affect ventilation, block travelway, cause injury. 48" conventional belt structure was covered.

Employee was struck on the back with a piece of slate.

A fall occurred in the 2nd south, #2 entry, 2800 ft station. The fall was 20' long, 20' wide & 8' high. The area was bolted with 6' & 8' pt anchor bolts. The fall did not affect ventilation, cause injury, block travel or damage equipment. No one is required to travel or work in this entry.

Piece of rock projected from miner tail, striking EE on right side of head. Required four sutures.

Miner was welding when a rock fell out of the top, striking his right hip.

His glove got caught on drill steel and he broke his thumb. He was checking the steel to see if it was straight.

A roof fall occurred in the Main West, #2 Entry, #33 crosscut. The fall was 20' long, 20' wide, and 8' high. The area was bolted with 6' & 8' point anchor bolts. The fall didn't affect ventilation, cause injury, block travel or damage equipment.

A roof fall occurred in the South Sub-Main, #3 Entry, #55 Crosscut. The fall was 20' long, 20' wide, and 8' high. The area was bolted with 6' & 8' point anchor bolts. The fall didn't affect ventilation, travel, cause any injury or damage equipment.

A roof fall occurred in the Main West, #5 Entry, #38 Crosscut. The fall was 25' Long, 25' Wide and 8' High. The area was bolted with 6' & 8' point anchor bolts. The fall didn't affect ventilation, travel, cause any injury or damage to equipment.

Pinched his finger while unloading bridge boards. His right middle finger was broken and required sutures.

A roof fall occurred in the 2nd west submain #3 entry #32 crosscut. The fall was 20'l x 20' w x 8'tall. The area was bolted with 6' to 8' point anchor bolts. The fall did not affect ventilation, travel, cause injury or damage equipment.