Dewey Quarry Metal/Non-Metal

Employee was walking and supervisor drove next to him in pickup. The mirror hit employee causing in turn for the employee to hit the bed of the truck.

Stepped off ladder and twisted ankle.

While hammering off bearing, steel sliver punctured hand & lodged in his left hand, index finger joint.

EE was walking across an elevated steel mesh walkway to a control house, when he slipped and fell on the walkway. It was snowing and sleeting at the time. The mid-rail and hand-rail prevented the EE from falling to the ground.

Fixing a V-16. Pushing a pipe wrench to dislodge a belt, Belt loosened and moved, placing his hand between a piece of metal and the wrench handle.

While using pipe wrench to change v-belt on screen, wrench slipped, catching hand between wrench and structural iron.

Putting v-belts on v-16 pulleys and rolled fingers into pulley and v-belts and cut and smashed fingers.

EE HAD A WRENCH ON A BOLT, TIGHTENING BOLT, AS HE RAISED THE WRENCH, MUSCLE WAS PULLED IN HIS BACK.

PUTTING GRATES IN HAMMERMILL AND SMASHED RIGHT HAND ON GRATE.

UNLOADING WATER PUMP OUT OF TRUCK INTO BUILDING.

GRINDING PAOINT OFF OF IRON AND IN TIME, THE OIL BASED PAINT WORKED ITS WAY AROUND HIS FACE SHIELD AND GOT IN HIS EYES. WE WERE UNAWARE OF THIS REPORTABLE INCIDENT, UNTIL WE RECEIVED AN EMERGE NCY ROOM BILL ON MAY 15, 2000. UPON INVESTIGATION, THE EE HAD TOLD HIS SUPERVISOR IT WAS ALLERGIES, NOT RELATED TO HIS JOB.

CUT THUMB WHEN HE WAS INSERTING A CAP BOOSTER INTO A HYDROMITE.

SLIPPED AND FELL HURTING BACK.

GETTING BUCKET OF WATER TO PRIME WATER PUMP ADN STRAINED BACK.

GREASING TOP RAMS OF LOADER, TURNED TO GET OFF AND FOOT SLIPPED AND HE FELL TO THE GROUND AND TWISTED KNEE.

HE WAS TAKING THE STRIKER BAR COUPLING OFF OF THE TAMBROCK DRILL AND IT DROPPED DOWN & HIS FINGER WENT DOWN WITH IT. SMASHING HIS FINGER ON THE COLLAR

TRIPPED ON WALKWAY WHILE CHANGING SCREENS.

SHOVELING CRUSHED ROCK FROM UNDER A TAIL PULLEY ON CRUSHER. (HERNIA)

WALKING ON CATWALK, STEPPED OFF STEP AND TWISTEDANKLE.

LOADING BLOW HOSE ON POWDER TRUCK. INCIDENT HAPPENED ON 4-9-97. NEXT TWO DAYS HE WAS OFF BECAUSEOF WEATHER. HE RETURNED TO WORK ON MONDAY, THE 14TH. HE WORKED UNTIL 4PM AND SAID HE NEEDED MEDI CAL ATTENTION AND HAS NOT RETURNED TO WORK SINCETHE 14TH.

CHECKING HEATER ON TEREX AND CUT FINGERS IN FAN.

STEPPING IN BETWEEN TWO WALKWAYS AND TURNED LEFT ANKLE, RESULTING IN A SPRAIN.

MOVING A GEAR REDUCER BOX, FELT PAIN IN LOWER BACK, THEN PUT ON OVERSHOES & BACK POPPED.

WHILE LIFTING MOTOR WITH FORLIFT, CHAIN WHICH HELD MOTOR IN PLACE, DROPPED MOTOR AND CAUGHT LEFT HAND BETWEEN FORKLIFT AND MOTOR.

61329NG ON ROCK SURFACE SLIPPED ON LOOSE ROCK SPRAINING & STRETCHING TENDONS & LIGAMENTS ON RIGHT ANKLE

WHILE WORKING IN SHOP ON TRUCK HE WAS USING PRYING BAR BAR SLIPPED CAUSING ELBOW TO SLIP & HIT TRUCK.

PLASTIC HANDLE CAME OFF OF COMEALON & THE COMEALONG HIT HIS ARM & CUT IT TOOK 9 STITCHES

THE INJURED WAS USING A GRINDER IN THE SHOP WHEN IT KICKED BACK HITTING HIM ON SAFETY GLASSES AND BRIDGE OF NISE,AND BREAKING THE NOSE.

CUT FINGERS WHEN FINERS WERE CAUGHT BETWEEN MEYAL STRIPS WHEN TRYING TO PUT IN A WIPER

NORTHEAST OKLAH2MA HAD AN EXTREMELY BAD ICE STORM THERE WAS ICE ON EVERYTHING HE FELL ON THE ICE ON THE GROUND HE BROKE HIS UPPER LEG REQUIRING A HIP JOINT REPLACEMENT

A ROCK FELL AND3BROKE THE TWO FINGERS ON RIGHT HAND OF EMPLOYEE

THE DUMP TRUCK WAS DOING UP THE RAM TO DUMP LOAD INTO FEEDER WHEN IT LOST POWER AND STARTED ROLLING BACKWARD, HE MISJUDGED THE EMERGENCY EXIT RAMP AND THE TRUCK HIT THE BURM WITH RIGHT REAR TI RES CAUSING THE UNLEVEL TRUCK TO TURN ON ITS SIESXXXX SIDE.

HE WAS USING A HAND GRINDER IN THE SHOP & A PC OF METAL SHAVINGS HIT HIM IN HIS LEFT EYE

TRYING TO LOOSEN ROCKS WERE JAMMED IN CRUSHER WHEN ONE ROCK ROLLED AND HIT HIS LEG.ORIG BELIEVED TO BE ONLY BADLY BRUISED LEG AND KNEE .. BUT LATER IT WAS DECIDED CARTILAGE WAS DAMAGED-SURGERY ON KNEE.