Mt Airy Mine And Mill Metal/Non-Metal

EE WAS SIZING A BLOCK TO BE MOVED WHEN A SMALL UNSEEN SHELL TURNED LOOSE WHERE EE HAD DRILLED EE'S HOLES TO BREAK THE STONE. THE EE CAUCHT THE SHELL WITH EE'S RIGHT HAND TO KEEP IT FROM FALLING AND HIT EE'S WRIST ON THE SHARP EDGE CAUSING A SMALL LACERATION. EE WAS RELEASED BACK TO WORK FULL DUTY SAME DAY

EE WAS LOOSENING A 5' LENGTH OF DRILL STEEL TO REMOVE FROM EE'S D30 DRILL WHEN THE WRENCH CAME LOOSE AND HIT EE'S RIGHT PINKY FINGER

EE WAS TIGHTENING THE BOWL ON EE'S 4' CONE CRUSHER AND THE CABLE EE WAS USING BROKE STRIKING THE EE IN THE LEFT FOREARM CAUSING A FRACTURE AND LACERATION.

EE WAS STANDING ABOUT 4 FEET FROM A MAINTENANCE EE THAT WAS REMOVING A PULLEY LOCKING COLLAR FROM A SHAFT AND A SMALL PIECE OF METAL WENT UNDER EE'S SAFETY GLASSES AND INTO RIGHT EYE

EE STATED THAT LEFT WRIST STARTED HURTING WHILE HELPING OTHER EMPLOYEES PACK 50# BAGS OF GRANITE GRIT ON PALLETS. EE WAS SENT FOR TREATMENT AND DIAGNOSED WITH TENDONITIS. EE STATED THAT LEFT WRIST HAD BEEN HURTING FOR A LONG TIME BUT NOT AS BAD AS THE DAY REPORTED

EE was cleaning out a pilot hole with a PVC blowpipe so EE could wire saw when the pipe separated and struck EE on the right forearm causing a contusion.

EE was removing saw wires from a block of granite that had been sawn when the end of the roughback broke free, fell and hit EE on the neck causing a laceration, and EE's right hand causing a contusion.

The Employee was changing a piece of Drill Steel in EE's Novamac Quarry drill. The employee stated that EE had EE's hand on the drill steel and hit the wrong lever which caused the extraction clamp to close and raised the steel bringing EE's hand through the clamp causing a fracture to EE's left hand. The employee returned to work the same day with light duty restrictions.

EE WAS REMOVING A JACK STAND FROM UNDERNEATH A FORKLIFT THAT HE HAD BEEN WORKING ON WHEN HE FELT A PAIN IN HIS RIGHT SHOULDER. EE WAS SENT FOR MEDICAL ATTENTION, AND WAS PLACED ON RESTRICTIONS, AND REFERED TO AN ORTHO FOR FURTHER EVALUATION.

A quarry employee bent down to pick up a 4" piece of air compressor hose to place on a pick up bed, and strained a muscle in his back.

An blasting employee stated that when he initiated a blast from a distance of 125 feet away, a piece of rock hit him in the upper left chest causing a rib fracture and contusion to his chest. Employee finished the workday, but went for medical treatment the next day 04/25/2014.

Employee was using a Band Saw to saw 6"x 6" wedges to be used as wheel chocks. When the blade went through the cut, the employees hand made contact with the blade causing a laceration.

The employee was pulling a wire saw cable by hand and felt a sharp pain in his lower back. Employee went to local emergency room on 05/03/2013. Diagnosis low back strain.

The employee was walking up a conveyor, he slipped causing his left ankle to receive his full weight causing pain. The result was a chipped bone in his left ankle.

Employee was using a water hose to wash residue off stone on the Quarry. As the employee walked backwards he stepped down approx. 8" and twisted his ankle resulting in a right ankle sprain.

The employee was removing a piece of waste granite from a saw cart using a steel lifting cable. The employee put pressure on the waste piece with a pry bar to allow the lifting cable to go around the waste piece. As he applied pressure a piece of the waste slab broke off and fell striking the employee on the left shoulder causing an abrasion and laceration.

The employee was dumping a piece of waste granite off the forks on a lift truck. The material rolled to the ends of the forks which lifted the back of the forklift. The material continued to fall off the forks which caused the rear of the forklift to fall back to the surface. The employee only decided to visit a doctor a couple of weeks after the event when the pain increased.

A piece of 11' drill steel fell out of a holder on a drill unit, the employee reached to catch the piece of steel and caught his finger between the drill steel and the retractor wheels.

The employee started to lift a metal screen up a 5 foot space when he heard his right elbow pop. He could no longer use his right arm. The result was a contusion of the right elbow.

The employee was dismounting a forklift, he slipped on a wet step and fell striking his elbow on the step.

The maintenance employee was testing a wire saw that had been repaired. While watching the saw move vertically, bolts broke, which held the saw to the frame allowing the saw to fall. The wheel guard struck the employee on the hard hat and shoulder. The employee fell to the floor. The employee was taken for medical attention where a contusion of the head and shoulder was diagnosed.

While changing a drill bit on a drilling machine, the employee accidentally activated the boom movement which caught his hand between the drill bit and stone surface. The result was a fractured 5th Metacarpal of the left hand.

The employee was using a band saw to cut a steel "H" beam. When the employee approached to move the completed piece it fell on his right foot, resulting in a contusion to the top of the right foot.

The employee was standing on a platform attached to a track drill. As he moved the drill he backed it into the side of an attached air compressor which pinned his foot between the two units.

Employee was walking across the quarry surface, he slipped on ice and fell on his left shoulder resulting in a contusion of the left shoulder.

Employee bent over to pull a steel cable under a granite block, when he stood up he felt pain in his lower back. The result was a Lumbosacral Sprain.

The employee was pushing on a hand held wrench. As the bolt came loose the employees hand hit against other metal which caused a laceration to the little finger of the left hand.

The employee placed his left foot on the step of a Volvo A235 haul truck, as he raised up, the cable step broke. The employee fell, causing his right leg to hyper-extend. The result was a sprained right knee.

Employee was lifting a piece of 21' long drill steel. A heavy wind caused the employee to stumble and twist causing a muscle strain to the lower back.

Employee was unhooking crane cables from a sawn granite block. He tripped on a steel cable lying on the concrete floor. He fell on his right side to the concrete floor resulting in a fracture of the right femur.

The employee was using a pry-bar to dislodge stone, which had hung in a feeder. When the stone came loose, it struck the pry-bar, causing the sharp end of the bar to puncture the palm of the employees right hand.

Employee sat down on an electrical motor, which had a lifting bolt protruding. The employee sat on the protruding bolt. The result was a contusion to the Genitalia.

The employee had built a warming fire in a small stove in a building for warming on the Quarry. While operating a drill, the employee noticed a box of rags next to the stove were on fire. The employee used a dry chemical extinguisher to put the fire out, but was overcome by the dry chemical fumes.

The employee was operating a metal lathe. A piece of metal shaving came toward the employee, which the employee deflected with his left hand resulting in a laceration to the middle finger of the left hand.

The employee was operating a front-end loader. While moving forward to load the bucket he hit an unseen rock ledge which threw the operator into the right armrest injuring the right lower ribcage.

The employee was adjusting a water supply line on a block of granite being sawn. The water spray blew a foreign body into his left eye.

As the employee stepped off the bottom rung of an equipment ladder he slipped causing him to strike his left knee against the steel rung of the ladder resulting in a fracture of the left kneecap.

The employee was walking on the Quarry surface. He slipped in a water/sludge area resulting in a fall to the quarry surface. The employee received outside medical attention for a laceration above the left eye.

The employee was attempting to free a stuck cutting wire on a wire saw. When the wire came free it flipped up & struck the employee above the left eye resulting in a laceration.

Employee was walking on level ground, stepped in a hole approx. 1'-6" wide x 5" deep. He sprained his left ankle.

The employee was preparing to remove some slabs from a trolley. While reaching for a crane sling, a piece of slab fell off the trolley, striking the employee on his right arm, left hand and right foot.

Employee was moving boxes of material. After storing one box the employee turned to get another, he tripped over a metal tank setting in the floor. The employee fell to the floor. The employee sprained his left knee.

Employee was attempting to free a rock hang in a jaw crusher using a hook attached to an electric winch. The hook jumped back striking the employee on the arm and hard hat. That night he went to the local emergency room where a precautionary CAT scan was preformed, there were no injuries, the employee received an injection of pain medication.

After placing a piece of granite on a saw cart trolley, the employee reached over to get a pry-bar. When the employee braced himself with his right hand, while leaning, the piece of granite rolled over onto his right hand, resulting in a fracture to the little finger and ring finger of the right hand.

The employee was changing a hydraulic fitting on a water jet using a pipe wrench. The wrench slipped causing him to strike the edge of his right hand on a piece of metal resulting in a fracture to the 5th metacarpal of his right hand.

The employee was climbing up the steps on a 988 Cat loader, he lost grip with his right hand which caused him to spin left which threw him off balance and he lost his footing. He fell to the ground resulting in a fractured left ankle.

Employee was using a power saw to cut the top off a plastic barrel. The blade stuck causing the saw to jump up and catch the little finger of the left hand which cut half the nail off.

The employee was installing toggle plate seats in the Primary Crusher. A metal shim fell on his left hand, resulting in a contusion to the index and middle fingers of the left hand.

The employee was hooking slings from an overhead crane to a group of granite slabs. The slabs shifted causing the employee to step backwards into a drain ditch, resulting in a twisted right knee.

The employee was using a wrench to tighten a bolt on a tractor drill. When the employee pushed the wrench it slipped off causing the employee to strike the knuckles of his right hand on a steel frame resulting in a contusion.

THE EE WAS REMOVING A STEEL LIFTING CABLE FROM A GRANITE BLOCK, THE CABLE TWISTED IN THE EE S HANDS CAUSING A CONTUSION TO THE OUTSIDE EDGE OF THE LEFT HAND.

THE EE WAS OPERATING A HYDRAULIC DRILLING MACHINE. HE WAS CHANGING THE STEEL DRILL ROD. DURING THE PROCESS HE ACTIVATED THE WRONG LEVER CAUSING THE DRILL TO ROTATE. THE ROTATION CUT AND BROKE THE SECOND FINGER OF THE LEFT HAND.

THE EE WAS USING A HAMMER TO STRIKE A METAL WEDGE. A PIECE OF THE WEDGE BROKE OFF AND STRUCK THE EE ON THE BACK OF THE LEFT HAND RESULTING IN A LACERATION.

THE EE WAS REMOVING DEBRIS FROM A SHED BEING TORN DOWN, HE STEPPED ON A BOARD THAT HAD AN EXPOSED NAIL WHICH PUNCTURED THE BOTTOM OF HIS RIGHT FOOT.

EE WAS USING A PRY BAR TO POSITION 6' BY 10' BY 2" GRANITE SLAB WHICH WAS SETTING ON ITS EDGE IN A RACK. THE EE PULLED THE SLAB PAST VERTICAL CAUSING THE SLAB TO FALL STRIKING THE EE ON THE HE AD AND SHOULDER. THE EE RECEIVED A LACERATION TO THE LEFT SIDE OF HIS HEAD BEHIND HIS EAR AND A CONTUSION TO HIS LEFT SHOULDER.

PUTTING 50LB BAGS ON A PALLET, CAUGHT TOE ON PALLET CAUSING BACK TO TWIST, RESULTING IN PAIN LOWER BACK

EMPLOYEE STEPPED OFF A TROLLEY ONTO A PRY BAR LAYING ON THE GROUND, TWISTED RIGHT ANKLE.

EE WAS SWINGING A SLEDGE HAMMER AT A STEEL WEDGE. THE HAMMER GLANCED OFF CAUSING THE EE TO CUT HIS LEFT HAND ON THE STEEL WEDGE.

EMPLOYEE SLIPPED, HIT KNEE ON A PIECE OF METAL ON A CEMENT MIXER. CONTUSION OF LEFT KNEE.

HIGH PRESSURE WATER DISLODGED A STONE CHIP WHICH STRUCK THE EE ON THE RIGHT SIDE OF HIS FACE RESULTING IN A LACERATION

WELDING PROJECT LASTING ALL DAY - FLASH BURN TO EYES.

THE EMPLOYEE WAS CLOSING THE ENTRANCE DOOR TO A BUILDING AFTER STEPPING INSIDE. HE PLACED HIS LEFT HAND ON THE DOOR CASING AND CLOSED THE DOOR RESULTING IN AMPUTATION OF 3/8" OF THE TIP OF HIS MIDDLE LEFT-HAND FINGER.

THE EE WAS HOLDING A PIECE OF STEEL TUBING WHILEANOTHER EE CUT IT FREE FROM A LONGER PIECE. WHEN THE PIECE WAS CUT FREE THE EMPLOYEE DROPPED IT ON HIS RIGHT FOOT.

THE EMPLOYEE WAS PULLING A PIECE OF CATWALK MATERIAL OVER ANOTHER PIECE WHEN THE BOTTOM PIECE SHIFTED AND CAUGHT HIS FINGER BETWEEN THEM.

THE EMPLOYEE STEPPED IN A HOLE AND TURNED HIS ANKLE.

THE EE WAS MOVING A SCREEN BY HAND MASHED HIS FINGER BETWEEN THE SCREEN AND A RAIL 12 STITCHES TO HIS FINGER.

THE EE WAS STANDING WITH HIS FOOT UNDER A BLOCK THAT WAS BEING SPLIT WITH A HAMMER AND WEDGER. THE EE WAS PICKING UP THE WEDGES FROM THE TOP OF THE BLOCK WHEN IT SPLIT AND DROPPED ONTO HIS LEF T FOOT.

EE WAS USING A SLEDGEHAMMER AND WEDGE TO SPLIT AGRANITE BLOCK. HE STRUCK THE WEDGE WITH A GLANCING BLOW AND WITH SUCH FORCE THAT A FRAGMENT CAMEOFF THE WEDGE AND STRUCK HIS RIGHT MIDDLE FINGER

THE EMPLOYEE WAS STRIKING A STEEL WEDGE THAT WAS IN A DRILL HOLE, WITH A SLEDGE HAMMER. WHEN THE WEDGE WAS STRUCK IT CAME OUT AND STRUCK THE EMPLOYEE IN THE MOUTH AREA.

THE EE WAS PULLING A LARGE SLIDING DOOR TO CLOSE IT WHEN HE STRAINED HIS RIGHT SHOULDER.

THE EMPLOYEE WAS TAKING THE GUIDE OFF THE STEEL, HE DID NOT NOTICE THAT THE STEEL HAD COME LOOSE FROM THE COUPLING, THE STEEL FELL CATCHING HIS FINGER BETWEEN THE BIT AND THE JAWS THAT HOLD IT .

THE EE WAS LIFTING A LIFT TRUCK FORK AND FELT A PAIN IN HIS LOWER BACK.

HE WAS PRYING SLABS APART WHEN THE END OF ONE SLAB BROKE. WHEN HE MOVED AWAY HE STRAINED HIS BACK.

THE EE HAD A HEART ATTACK DURING HIS LUNCH. THE LOCATION WAS OFF SITE AT THE FLAT ROCK RURITAN BUILDING WHERE THE ANNUAL REFRESHER TRAINING CLASS WAS BEING CONDUCTED.

THE INJURED PERSON WAS MAKING WEDGES ON THE TRIP HAMMER WHEN THE METAL KICKED BACK CAUSING THEOPERATOR TO TWIST SUDDENLY TO THE SIDE.

1 EE WAS PUSHING SLABS APART WITH PRY BAR AS THEPERSON WAS INJURED WAS PUTTING BELT AROUND THE SLAB SO THE CRANE COULD LIFT IT. THE SLAB BR0KE AS HE WAS BENDING OVER TO PLACE THE BELT UNDER & FELL TOWARD HIM STRIKING HIM BEHIND THE RIGHT EAR IN A GLANCING BLOW PUSHING HIM OUT OF THE WAY

HE WAS DRIVING A WEDGE WITH HIS RIGHT HAND AND HAMMER, HE MISSED THE WEDGE AND THE RIGHT INDEX FINGER HIT A PULLEY.

THE OPERATOR SLIPPED OFF THE BLOCK CAR AND STEPPED ON THE OVERFLOW HISE TWISTING HIS ANKLE.

A FORKLIFT PULLING OUT A BLOCK FROM A LEDGE DRUG A SPRAWL WITH THE BLOCK WHICH TURNED OVER ON HIS FOOT.

THE EE WAS SPLITTING A STONE WITH A HAMMER AND WEDGE. AS HE STRUCK THE WEDGE IT BROKE AND HIT HIM ON THE RIGHT LEG, (SHIN AREA) BREAKING THE SKIN AND BRUISING IT.

HE STUMBLED AND TIRED TO CATCH HIS BALANCE WITH HIS LEFT HAND, THE TORCH IN THE RIGHT HAND WENT ACROSS THE BACK OF HIS LEFT HAND BURNING THE BACK OF THE LAST 3 FINGERS.

A SMALL BLOCK OF GRANITE BROKE INTO TWO PIECES AND ONE PIECE FELL BACK ON HIS FINGER.

THE EE SLIPPED WHILE STANDING ON A BLOCK CART, AS HE CAUGHT HIS BALANCE HE TWISTED HIS BACK CAUSING A SHARP PAIN IN HIS BACK.

A CABLE FROM THE CRANE PULLED HIS FEET OUT FROM UNDER HIM CAUSING HIM TO FALL Y

EE WAS LIFTING A PUMP IN THE L.S.V.SLABING PLANT.

EE REPORTED ON 6-8-99 THAT BACK ON 6-3-99 LIFTING A CROSS TIE HE GOT A HERNIA.

EE PICKED UP 10' SECTION OF DRILL STEEL AND FELT PAIN IN LOWER BACK.

EE TWISTED ANKLE ON WALKWAY OUT OF THE SCREENING TOWER.

WIRE SAW OPERATOR. EE FELL OFF THE END OF THE CART INTO THE WIRE SAW PIT.

EMPLOYEE SLIPPED AS HE CAME OFF FORKLIFT. HE WAS GETTING DOWN THE CORRECT WAY AND HAD HIS HAND ON THE HANDRAIL. BUT WHEN HIS FOOT SLIPPED HE PULLED HIS BACK.

EE IS BANKER MAN FOR SAW SHEET CRANE. THEY WERE PICKING UP BLOCK AND EE GOT FINGERS BETWEEN CABLE AND BLOCK.

EE SLIPPED GETTING OFF FORKLIFT AND JERKED HIS BACK AS HE CAUGHT HIMSELF.

EE WAS ADDING DRILL STEEL TO TAMROCK DRILL WHEN HE SLIPED. THE WEIGHT OF STEEL STRAINED HIS LEFT ARM. EE DID NOT REPORT THIS AT THE TIME AND DID NOT SHOW UP OR CALL US UNTIL 6-4-98. WE WERE, O F COURSE AND READY TO RIVE HIM BY THEN.

EE WAS WASHING SLABS THAT CAME OUT OF GANG SAW. WE HAVE TO WASH THE SLABS BEGORE THE STEEL SHOT RUSTS INTO THE GRANITE. THESE SLABS ARE THIN AND PULLED BACK BY HAND. EE LET ONE MASHE FINGER.

EE WAS REFUELING OVER DROP BALL (CRANE) AND SLIPPED ON THE WALKWAY AND FELL. THE WALK HAD FROST ON IT. HE BRUISED HIS SIDE IN THIS FALL

EMPLOYEE WAS SHOVELING LOOSE MATERAIL FROM BAG MACH. BELTS. HE TWISTED HIS BACK WHILE SHOVELING. EMPLOYEE DID NOT REPORT INJURY UNTIL 12-3-97.

EE IS A WIRE SAW OPERATOR, BUT WAS HELPING FORKLIFT OPERATOR AT TIME OF ACCIDENT. HE WAS SEPERATING 16" THICK CURB SLABS SO FORKLIFT COULD LAY THEM DOWN FLAT. HIS PRY BAR SLIPPED AS HE PLACED WEDGE BETWEEN TWO SLABS AND THE SLABS CAME BACK TOGETHER ON HIS "L" THUMB.

EE RUNS THE DROP BALL ON THE QUARRY. THE CAB IS ON THE RIGHT SIDE. FOR SOME REASON (?) HE USED AHAND HOLD FOR A STEP AND TRIED TO JUMP TO THE LEFT SET OF TRACKS. HE WAS IN THE MIDDLE OF OUR FL AT QUARRY FLOOR THERE WAS NO REASON TO MAKE GETTING DOWN SO HARD. HE LANDED ON THE TRACK WITH HIS RIBS.

LIFTING 100 LB BAG OF EMERY [WIRE SAW GRIT] & FELT A STING ON LEFT SIDE.

EMP WAS WORKING LEVER ON A COME A LONG (WINCH) AND PULLED CHEST MUSCLE.

EMPLOYEE CUT HAND ON HOSE CLAMP ON WATERHOSE. 3 STITCHES BETWEEN THUMB AND FIRST FINGER (RIGHT HAND).

EE WAS PUTING NOW BLADES IN GANG SAW. HE HURT HIS BACK LIFTING BLADE.

EMPLOYEE PULLED OPEN METAL DOOR TO PUMP HOLE. HE FELT PAIN AND SOMETHING PULL.

BOUNCED ON TOW MOTOR. PULLED LOWER BACK.

EE TURNED TO PICK UP OIL CAN. HE FELT PAIN IN HIS BACK FROM THIS MOMENT.

EE WAS SAWING WIRE SAW WIRE INTO WITH HAND HELD HACK SAW. THE SAW SLIPPED AND CUT HIS LEFT THUMB.

EMPLOYEE WAS COUPLING CABL ETO GANG SAW CART. HE DROPPED THE METAL COUPLIN ON HIS FINGER.

EE WAS MOVING ROCKS BY HAND THAT HE SHOULD HAVE USED THE FORK LIFT ON. HE DROPPED A SPRAIN ROCK ON HIS FOOT. HE WAS LIFTING BY HAND FIRST AID TYPE INJURY EXCEPT EE HAD LAID OUT A COUPLE DAYS.

EMPLOYEE WAS BANKERING FOR OVERHEAD CRANE. THE INJURY OCCURRED WHEN THE BLOCK HE WAS GUIDING CRUSHED AGAINT A BLOCK NEXT TO IT.

EE WAS WORKING ON A 6-0 HIGH LEDGE. HE NEEDED TO DESCEND FROM THE TOP TO THE FLOOR OF QUARRY. HE MISSSTEPED GOING DOWN THE LADDER AND TWISTED HIS ANKLE AS HE STEPED TO THE FLOOR OF QUARRY.

EE CLIMBED INTO GANG SAW WHILE RUNNING TO UNSTOP HOSE. HE WAS NOT SUPOSED TO DO THAT. PROPER PROCEDURE IS LOCK OUT MACH. HE PLACED HIS HAND OR THE TRACK FOR THE MOVING SHOWER IN THE TOP OF THE SAW THE WHEELS OF THE SHOWER RAN OVER HIS HAND.

EMPLOYEE WAS CATCHING WOOD ETC OFF BELT TO FIRST CONE CRUSHER HE WAS RUNNING SCRAP SLAB MATERIAL FROM THE LSU FIMNISHING PLANT THIS MATERIAL HAD WAY TOO MUCH WOODINGS ETC IN WITH IT CAUSING TH E CONE CRUSHER OPERATOR A LOT MORE TROUBLE THAN NORMAL HE GOT CARELESS & PUT HIS HAND IN STHE WRONG PLACE

EMPLOYEE WAS DRIVING WEDGES INTO STONE TO SPLIT IT HE WAS USING A 1015 HAMMER HE MISSED THE WEDGE & HIT THE GRANITE THE HAMMER BOUNCED BACK UP & HIT HIM ON THE NOSE

RIGHT FOOT WAS CAUGHT INSIDE WOODEN PALLET WHEN PALLET WAS BEING REMOVED BY FORKLIFT.

MOVING STEEL AIR PIPE GROIN STRAIN OCC

EMPL BROKE 2 FINGERS WHEN HE RAN HAND-HELD AIR-POWERED STONE TRACER OFF END OF ROCK.MASHED 2 FINGERS BETWEEN TRACER AND ROCK WITH HIS OWN BODY WEIGHT.

EMPLOYEE SLIPPED AND FELL DOWN. HE LANDED ON HIS ELBOW AS HE TRIED TO BREAK HIS FALL. HE WAS ON THE QUARRY SURFACE WORK IN A LEDGE AREA WHEN HE SLIPPED.

STEPPED ON WOOD PALLETT AND TWISTED FT. FRAC INLEFT FT.

EMPLOYEE WAS ATTEMPTING TO UNJAM A BOX,ON THE BAG MACHINE IN GRIT ROOM.THE MAN WAS NOT ON. EMPLOYEE LET THE BOX FALL BACK INTO PLACE ON HIS HAND.

EMPLOYEE WAS CA6LKING A SEARRING WITH A GLUE GUN. (HAND POWERED GLUE GUN) THE HOSE ON THE GUN BURST AND SOME OF THE GLUE WENT INTO EMPLOYEE'S EYES. (HE HAD HIS GLASSES ON).

EMPLOYEE WAS DR3VING WEDGES WITH A 5 POUND HAMMER ON QUARRY LEDGE. HE MISSED THE WEDGE AND HIT THE QUARRY SURFACE. THE HAMMER BOUNCED BACK UP AND HIT HIM ON THE FOREHEAD.

FRONT-END LOADE9 OPERATOR HURT BACK AND RIB WHEN HE HIT A LEDGE WITH BUCKET.

EMPLOYEE WAS WA5KING DOWN STEPS FROM OVERHEAD CRANE.HE TWISTED HIS KNEE WHEN HE STUMBLED.

EMPL GETTING IN7O FORKLIFT TRUCK AND FOOT SLIPPED ON TOP STEP CAUSING HIM TO FALL TO GROUND.

EMP WAS HIT IN 4OUTH BY A 2" X 16' LONG I-BEAM. HE WAS GOING TO DUCK UNDER THIS BEAM, A TAC WELD HOLDING THE BEAM BROKE, IT DROPPED HIT HIM IN MOUTH

EMPLOYEE STEPPE8 INTO A HOLE AND TURNED HIS ANKLE.

EMP WAS USING A3 ELECTRIC DRILL. THE DRILL BIT CAUGHT AND THE DRILL TWISTED HIS HAND INTO METAL BEAM

CRUSHER MAINT. 9MPLOYEE WAS HELPING REPLACE JAWS OF CRUSHER HE GAVE UP SIGNAL TO CRANE OPERATOR WITH HIS HAND ON CABLE HIS LITTLE FINGER WENT THROUGH PULLEY

EE WAS USING A 2 1/2# HAMMER & MISSED THE WEDGE HE WAS SWINGING AT. THIS STRAINED HIS LOWER BACK.

EMP WAS DOING R9PAIR WORK ON GANG SAW HE BENT OVER TO PICK UP A 4X4 PIECE OF WOOD AND SLIPPED THIS CAUSED HIM TO PULL A MUSCLE IN HIS BACK

EMPLOYEE WAS DRILLING SLABS INTO LENGTHS FOR SPLITTER MACH. HE HAD SPLIT TWO LENGTHS AND WAS USING A BAR TO PULL THEM APART. HE PULLED ONE OVER ON HIS LEG. HE SHOULD HAVE BEEN STANDING ONTHE O THER SIDE OR ON TOP.

I.NAME WAS MOVING A 20LB BLOCKS ALONG ROLLERS FROM ONE SPLITTER MACH. TO THE NEZXT. HE PULLED THE ROCK WITH HIS LEFT HAND ACCROSS HIS RIGHT HAND

EMPL MAKING RUBLE USING AIRPOWERED HANDTOOL THIS SLIPPED OFF EDGE OF STONE HAND WAS MASHED BETWEEN TOOL AND ROCK.

EMPLOYEE WAS MAKING BRICKS WITH BLOCK MACH WHILE POSITIONING A 25LB ROCK WITH MACH OFF HE MASHED THE TIP OF HIS L RING FINGER BETWEEN ROCK AND MACH

AUTO MECH. WAS WORKING ON EUCLID STANDING ON FOOT STOOL THE FOOT STOOL KICKED OUT HE GRABBED FENDER WITH RIGHT HAND THE PULL OF HIS FALLING WEIGHT POPPED HIS SHOULDER OUT OF JOINT

EMPLOYEE WHILE WORKING ON A WIRE SAW HE LEFT AN 8 4X4 STANDING ON END AND JEAN AGIANST A POST THIS FELL OVER AND HIT HIM ON THE HEAD.

BANKER MAN GOT FINGER MASHED BETWEEN TWO SLABS WHILE BANKER\S SAW.

THE EMPLOYEE WAS WORKING TO REPAIR A WIRE SAW WHILE USING 20 LB HAMMER TO DRIVE A SHAFT HIS OVER EXERTION SPRAINED HIS RIGHT SHOULDER.

MAINTANACE MAN WAS WORKING ON A GANG SAW HE LOST HIS BALANCE WITH A 20LB HAMMER AND PULLED A MUSCLE IN HIS BACK.

DRILLMAN WAS DRILLING CLAY OUT OF A 30HR OLD LIFT HOLE. HE BENT OVER TO PICK UP A LOOSE BOLT HE FOUND ON THE GROUND. AT THAT TIME THE DRILL BROKE THREW THE CLAY & RELEASED THE FUMES & SLATE AIR. DAZED BY THE FUMES HE FELL FACE DOWN.

TRIPPED OVER CABLE THAT PULLS IN GANGSAW CAR.

HUNG FOOT OVER DOOR,FELL TWISTING KNEE.

HIS RIGHT HAND WAS PINCHED BY A SPLITTING MACH.

EMPLOYEE SLIPPED INTO THE CAR THAT THE BLOCKS SET ON FOR GANG SAWING THE IMPACT FRACTURED SOME RIBS

EMPLOYEE WAS PUTTING DIRT IN HOLE WHEN THE LEDGE RAN OUT FROM NATURAL EXPANSION THIS CAUSED A STONE TO FLY UP AND HIT HIM ON THE FOREHEAD

EMP STEPPED IN A HOLE IN THE METAL PLATFORM HE WAS WORKING ON AND SCRAPED HIS KNEE

CUT ARM ON SHARP PIECE OF STONE

EE WAS CHANGING BLADES ON GANG SAW WHEN ONE OF THE BOARDS USED AS A BRACE FLEW UP & HIT HIM ON THE NOSE.

EMPLOYEE WAS PRYING A ROCK LOOSE WITH A BAR AND CAUGHT HIS FINGER BETWEEN BAR AND A BEAM HE USED AS A PIVOT POINT

EMPLOYEE CUT INDEX FINGER ON THE EDGE OF A SHARP PIECE OF METAL.

EMPLOYEE WAS INSTALLING A SECTION OF CATWALK, WHILE DOING SO HE DROPPED IT ON HIS FOOT.

EMPLOYEE WAS STANDING BESIDE A FORKLIFT THE FORKLIFT DROVER OVER A PCS OF STONE THE STONE SHOT OUT FROM UNDER THE TIRE STRIKING THE EMPLOYEE ON THE LEG