Pleasanton Plant Metal/Non-Metal

On 11/9/23 Maintenance employee was standing on a platform not suitable to work attempting to adjust a head pulley guard. During the process the employee lost balance and began to fall backwards, the employee managed to catch themselves by using their right arm.

Employee was removing a guard from the head pulley. When doing so, EE dropped the guard on the top of left foot resulting in a contusion to EE's left foot.

Employee was looking up to adjust some rollers, when a foreign matter fell into EE's right eye. The following day the employee reported the incident and requested medical treatment.

Employee alleges that while shoveling material onto the conveyor, EE experienced a strain to EE's right shoulder. On October 1, 2021, the employee requested medical treatment; EE was treated at the clinic where EE was prescribed work restrictions.

Employee was attempting to reposition conveyor belt back on track and heard a pop in EE's shoulder. On 1/21/21 EE was diagnosed with a right shoulder strain and was prescribed physical therapy.

On 4/23/2019 employee received surgery for a lower left arm laceration. Employee was performing routine maintenance inside the crusher when EE's hand slipped causing EE's lower left arm to make contact with the socket resulting in a laceration.

Employee alleges pain in right shoulder. While entering telehandler, employee had left hand on the steering wheel and right hand on the back of the seat. When stepping in, employee felt pain and heard/felt a pop in right shoulder.

On July 24, 2018, EE requested a medical evaluation and was placed on restricted duty. On July 10, 2018, EE felt pain in groin while shoveling; EE was diagnosed with a right inguinal hernia.

On 1/25/18 employee was taken to the company clinic and received stitches for a facial laceration. Employee, while performing clean-up duties, tripped over a 6" metal channel and fell to the ground. During the fall, the left side of EE's face struck another channel resulting in a laceration on the left cheek.

On 4/12/17, employee requested medical treatment and was prescribed chiropractic therapy by a physician. The employee alleged that ee hit head, while wearing hard hat, on a cross beam while walking under blade mill 1A in the process of greasing the plant equipment. EE was diagnosed with cervical and thoracic spine strains and was returned to full duty.

The employee requested medical treatment on 5/23/16, was taken to the occupational clinic and was placed on modified duty which is being accommodated. The employee alleged that pulling a rope for a pump float resulted in an annular tear at c7. The extent of the alleged injury is questionable.

On 10/2/15 the employee was taken to the emergency room for a laceration, received stitches and was placed on restricted duty. The head of a sharpened clamp rail bolt twisted in the employee's hand during a screen installation and cut through his glove, causing a laceration to his R-middle finger. He was returned to full duty on 10/5/15.

Authorities believe the incident that occurred to be a trespasser's suicide and attempted murder involving a couple. The male driver drove their vehicle onto Vulcan property at high speed into a holding pond and drowned. The female passenger escaped and summoned help from a Vulcan employee. Deceased was 30 yrs. old, DOB unknown and per MSHA Denver, use 1-1-85.

On 6/4/2014, the employee was taken to the emergency room where he received stitches for an eyelid laceration. While the employee was using a chisel and hammer, the chisel dislodged and struck him in the face. The employee was diagnosed with a left eyelid laceration and was released to full duty on 6/5/14.

On 11/6/13 the employee was taken to the hospital and received stitches for a laceration. While grinding on a crusher rotor, the grinder kicked back and struck the employee in the mouth resulting in a laceration to the upper lip. The employee was released to full duty on 11/7/13.

Employee went to Company clinic on 3/29/11 and was placed on restricted duty. He voluntarily retired effective 3/31/11 and requested medical treatment 3 days prior to his last day on the job. Employee alleges: for 2 years repetitive movement of climbing stairs and walking has caused L-knee pain. He was released to full duty on 4/5/11.

On 9/21/2010 the employee was taken to the company clinic, was diagnosed with R-Elbow Inflammation and was returned to restricted duty. On 9/17/10 the employee reported that while attempting to remove a guard, he pulled a muscle in his R-Forearm and refused medical treatment at that time.

The employee went to the clinic on 4/26/10, was diagnosed with a splinter/paronychia (abscess), and was returned to full duty. On 4/26/10, the employee reported: On 4/20/10 he was allegedly reaching for tools that were in his tool storage tray and a wood sliver went under his R-thumb nail.

On 03/30/2010 employee requested medical treatment and was placed on modified duty for an injury that occurred on 03/29/2010. Employee reported that while removing a bearing with a torch, grease flashed up resulting in 2nd degree burns to the nose and right cheek. Modified duty was accommodated.

On 12/19/09, the employee was taken to the company clinic and sutures were applied to the injury site. While employee attempted to catch a falling section of conduit, the conduit landed on the L-finger, resulting in a laceration. The employee was returned to full duty.

On 11/9/09 the employee was taken to the company clinic for ALLEGED R-knee pain and was returned to full duty. On 12/22/09, the company physician faxed a letter indicating a limited duty work status effective 12/16/09. The employee alleges he was injured at work but does not cite a specific event.

While removing north screw of blade mill BM-1 using come-alongs, the shaft shifted unexpectedly and employee's right leg was caught between the flights of the north and south screws. A root cause was stored energy not controlled.

Employee went to company clinic on 1/3/08 and was returned to full duty. On 3/4/08 employee returned to the clinic and was placed on restricted duty. The employee was inspecting the plant before start-up and slipped on stairs resulting in a left knee sprain.

The employee went to see the company doctor on 9/12/2006 and was placed on restricted duty. The employee ruptured his R-shoulder tendon by lifting an end of a rail road tie onto the forklift.

The employee went to see the company clinic on 5/4/2006 and was returned to full duty. While adjusting the scrubber, the employee struck L-index finger with the hammer which caused a laceration that required sutures.

THE EE WENT TO SEE THE COMPANY DR ON 2/14/06 AND WAS TAKEN OFF WORK. THE EE ALLEGES PHYSICAL ASSAULT AND SEXUAL HARRASSMENT CAUSING STRESS. (ALLEGED)

Employee went to see the company doctor on 5/12/2005 and was placed on regular duty. Employee went back to see company doctor on 5/16/2005 and was placed on restricted duty. Due to a previous and ongoing injury to his R-knee, employee began to favor his L-knee, resulting in an alleged strain to his L-knee.

Employee went to see company doctor on 11/4/2004 and was placed on restricted duty. Employee was climbing up the side of the jaw crusher to look inside, he slipped off the step and fell to the catwalk below, which resulted in a contusion to the left ribs and left arm.

Employee went to see company doctor on 10/27/04 and was placed on modified duty. When putting together shelf units, the top shelf fell and fractured employee's right thumb.

EMPLOYEE CLIMBED ONTO THE DOZER ON TRACKS, LOST BALANCE AND FELL OFF DOZER.

EMPLOYEE WENT TO SEE A DOCTOR ON 1/16/04 AND WAS PLACED ON RESTRICTED DUTY UNTIL 1/19/04 DUE TO A FRACTURE TO HIS TOE. EMPLOYEE WAS TURNING OVER A SKID STEER BUCKET TO INSTALL A NEW BOTTOM PIE CE AND BUCKET DROPPED ON HIS LEFT FOOT CAUSING A CONTUSION TO LEFT FOOT AND A FRACTION TO HIS LEFT TOE.

EE WAS PULLING ON A "TAG LINE" DURING THE INSTALLATION OF NEW CONVEYOR EQUIPMENT. THE LINE CAME LOOSE CAUSING THE EE'S ARM TO SNAP BACK AND INJURE RIGHT SHOULDER.

EE SPENT SEVERAL HOURS USING AN 8 LB SLEDGE HAMMER BEATER TO DRIVE IN CONNECTING PINS ON NEW CONSTRUCTION. AFTER SEVERAL HOURS OF REPETATIVE MOTION. THE EE ADVISED HIS FOREMAN THAT HIS RIGHT E LBOW WAS SORE. THE EE WAS RETURNED TO NORMAL DUTY BY THE DR WITH NO LOSS OF TIME.

EE WAS REMOVING A STEEL FRAME FROM A RAILING THAT WAS BEING INSTALLED ON A NEW PRODUCTION PLANT/THE FRAME WAS ATTACHED TO THE RAIL BY BOLTS AND TACK WELDS. AFTER REMOVING THE BOLTS THE TACK WELDS FAILED TO HOLD THE FRAME CAUSING IT TO FALL 6" ON TO THE EE FOOT.EE INCURED A MINOR FRACTURE TO HIS BIG TOE ON HIS RIGHT FOOT. THE EE WAS ABLE TO CONTINUE WORKING HIS NORMAL DUTIES NO LO

EE NOTED DISCOMFORT IN HIS RIGHT EYE AFTER THE END OF HIS SHIFT. HE REPORTED THE DISCOMFORT TO HIS SUPERVISOR ON 8-27-03 AND WAS SENT TO THE CLINIC. HE SPENT THE DAY INSTALLING TAIL GUARDS AND CLAIMED HE WAS WEARING SAFETY GLASSES AT ALL TIMES. IT WAS NOT NOTICEABLY WINDY.

WHILE INSTALLING BEARING ASSEMBLY IN CRUSHER THE MOUNTING PLATE FELL AND CAUSED A LACERATION TO EMPLOYEE'S LEFT MIDDLE FINGER. HE WENT TO SEE COMPANY PHYSICIAN ON 1/7/03; STITCHES WERE APPLIED AND HE WAS RETURNED TO FULL DUTY.

WHILE LOOSENING THE RETURN ROLLER WITH AN OPEN-END WRENCH, THE WRENCH WAS CAUGHT IN THE CONVEYOR BELT CAUSING A LACERATION TO THE RIGHT HAND. EE WENT TO SEE COMPANY DOCTOR ON 10/10/02, BUTTE RFLY BANDAGES (STERI STRIPS) WERE APPLIED AND EE WAS RETURNED TO FULL DUTY.

EMPLOYEE WENT TO SEE COMPANY PHYSICIAN ON 10-9-02, STITCHES WERE APPLIED AND EMPLOYEE WAS RETURNED TO FULL DUTY. WHILE USING A RAZOR KNIFE TO CUT RUBBER LINERS, EE RECEIVED A LACERATION IN LEF T RING FINGER.

EMPLOYEE WENT TO SEE COMPANY PHYSICAIN ON 12/19/02 AND WAS PLACED ON RESTRICTED DUTY. WHEN WALKING THROUGH TRUCK SHOP TO TURN ON LIGHTS, EMPLOYEE STEPPED ON KING NIPPLE LAYING ON FLOOR AND SPR IANED HIS R-KNEE.

EE WENT TO SEE CO DR ON 9-5-02 AND WAS TAKEN OFF FOR ONE DAY AND PLACED ON RESTRICTED DUTY. EE HAS A LUMBAR STRAIN FROM RUNNING LOADER AND DOZER ALLEGED.

ADJUSTING A WATERVALVE, EMPLOYEE STEPPED DOWN ONTO A PLATFORM & TWISTED HIS RIGHT KNEE. HE WENT TO SEE COMPANY DOCTOR ON 8/29/02 & WAS PLACED ON RESTRICTED DUTY.

LARGE PIECE OF CLAY FELL ONTO EE'S LOWER BACK & LOWER LT. LEG WHILE CLEANING MACHINERY WITH PRY BAR. INJURING LOWER BACK AND BREAKING SMALLER BONE IN LOWER LT. LEG.

EE WENT TO SEE COMPANY DR ON 2-25-02 AND WAS PLACED ON MODIFIED DUTY. SITTING IN HAUL TRUCK WAITING TO BE LOADED, OPERATOR OF FRONT END LOADER ALLEGEDLY DUMPED LOAD VIOLENTLY IN HAUL TRUCK CAU SING THORACIC/CERVICAL STRAIN TO DRIVER OF HAUL TRUCK ALLEGED.

EE WENT TO CO. DR. ON 12-3-01 AND WAS TAKEN OFF WORK. EE STEPPED IN MUD AND HEEL DROPPED CAUSING LEFT CALF MUSCLE STRAIN. (ALLEGED)

EE WENT TO GO SEE CO DR ON 11-16-01 AND WAS PLACED ON MODIFIED DUTY. EE WAS MEASURING COUNTER WEIGHT WHEN TAPE MEASURE WAS PULLED BY CONVEYOR BELT CAUSING A LACERATION TO LEFT MIDDLE FINGER.

EE WENT TO DR CO DR ON 11-16-01 AND WAS PLACED ON MODIFIED DUTY. EE WAS STEPPING OFF FROM LOADER ON UNEVEN GROUND, TOOK STEP AND HEARD LEFT HIP POP.

EMPLOYEE WENT OT SEE DOCTOR ON 10-11-01 AND WAS TAKEN OFF WORK. PUTTING A BRACKET ON A PIECE OF CONDUIT, THE EMPLOYEE LIFTED THE CONDUIT WITH A SCREWDRIVER WHICH SLIPPED, RESULTING IN THE COND UIT COMING DOWN AND SMASHING THE EMPLOYEE'S RIGHT FINGER.

EMPLOYEE WENT TO SEE HIS DOCTOR ON 8/17/01 AND WAS TAKEN OFF WORK. A PIECE OF METAL IMBEDDED INTO EMPLOYEE'S R-EYE WHILE GRINDING ON A LOADER BUCKET.

INJURY WAS REPORTED AS A FIRST AID ON 6/20/01 & BECAME MEDICAL ON 9/27/01. THE EMPLOYEE WENT TO THE COMPANY CLINIC ON 9/27/01, WAS RETURNED TO FULL DUTY, X-RAYS WERE TAKEN AND WERE POSITIVE. WHILE CLIMBING UP ON LADDER, EMPLOYEE SLIPPED OFF STEP AND FELL ONTO BUTTOCKS.

EMPLOYER WAS NOTIFIED ABOUT THE INJURY ON JULY 5, 01. EMPLOYEE WENT TO SEE THE COMPANY DOCTOR ON 6-22-01 AND WAS PLACED ON RESTRICTED DUTY. WHILE PULLING HOSE THROUGH THE MUD, EMPLOYEE FELT A POP IN HIS GROIN AREA.

FIRST AID REPORT WAS FILED ON 4/27/01 AND ON 2/11/02. IT BECAME NECESSARY FOR THE EMPLOYEE TO SEE OUR COMPANY DOCTOR WHO RELEASED HIM TO MODIFIED DUTY. WHILE LIFTING A HEAVY STEEL PLATE, EMPL OYEE STRAINED LEFT GROIN AREA.

EE WENT TO CO. DR. ON 4-26-01 AND WAS PLACED ON RESTRICTED DUTY. CLEANING OUT THE CONE CRUSHER WITH A BAR, EE STRAINED THE RIGHT SIDE OF GROIN.

EMPLOYEE WENT TO SEE A DOCTOR ON 11-8-00 AND WAS PLACED ON RESTRICTED DUTY. OBSERVING DOZER PUSH MATERIAL INTO DOZER TRAP AND AS AIR WAS DISPLACED FROM FEEDER, IT CARRIED AIRBORNE PARTICLES WH ICH ENTERED EMPLOYEE'S RIGHT EYE.

EMPLOYEE WENT TO SEE DOCTOR ON 8-17 AND WAS PLACED ON RESTRICTED DUTY. WHEN EMPLOYEE LEANED BETWEEN CONVEYER BELT TO FREE FROZEN IDLER, SLEEVE OF OVERALLS WAS GRABBED AND ARM WAS PULLED BETWEE N IDLER AND BELT AND BELT WHICH CAUSED A LACERATION TO RIGHT FOREARM.

EMPLOYEE WENT TO DOCTOR ON 7-25-00 AND WAS PLACED OM TEMPORARY DISABILITY. EMPLOYEE DROVE OFF DESIGNATED ROUTE TO AN AREA ONLY ALLOWED FOR DOZERS, TRUCK ROLLED ON TO THE SLOPE AND EMPLOYEE BUM PED KNEE ON STEERING COLUMN.

EE WENT TO SEE DR ON 5/23/00, STITCHES WERE APPLIED AND EE WAS RETURNED TO FULL DUTY.

EE WENT TO SEE DR ON 1/27/00 AND WAS PLACED ON MODIFIED DUTY. WHILE LOWERING PUMP INTO ROCK TUNNEL, EE WAS PUSHING AGAINST PUMP WITH RIGHT HAND UNDERNEATH PUMP. PUMP HUNG UP ON SOME OBJECT AND DROPPED ONTO EE'S HAND.

WHILE CLIMBING INTO CAB OF A 637 SCRAPER, EE FELT PAIN IN RIGHT KNEE. *EE IS ON MODIFIED DUTY WITH RESTRICTIONS.

A FOREIGN OBJECT BOUNCED UP UNDER EMPLOYEE'S SAFETY GLASSES WHILE HE WAS CHIPPING MATERIAL/SLAG WITH A CHIPPING HAMMER.

WHILE WELDING WITH WELDING HOOD AND SAFETY GLASSES ON, WELDING BERRY BOUNCED ITS WAY INTO MY LEFT EYE.

EE WAS MOVING A ROLLER W/ANOTHER EE WHEN THE OTHER EE DROPPED THEIR END OF THE ROLLER. END OF ROLLER CAUGHT WEB OF LEFT IN THE THUMB AREA CAUSING PUNCTURE WOUND. PUNCTURED THROUGH EE'S GLOVE

EE WAS HOLDING A WEDGE WHILE ANOTHER EE WAS STRIKING IT WITH A HAMMER THE HAMMER SLIPPED OFF THE WEDGE AND STRUCK THE FIRST EE'S FINGER.

EE WAS LINING UP 2 SIDES OF CONVEYOR BELT WHEN HIS HAND SLIPPED & HIT CONVEYOR FRAME

WAS ADJUSTING BELT AT TRANSBOX WHEN A CLAYBALL MUD BALL BOUNCED OUTOF BOX AND STRUCK EE IN THE HEAD

EE'S KNEE SWELLED UP AFTER CONSTANT KNEELING IN THE SCREEN PAN WHICH WAS LAYERED WITH 1/2" ROCK.

EE'S BACK BECAME SORE AFTER INSTALLING A CONVEYOR GUIDE ROLLER.

EE TWISTED RIGHT KNEE WHILE IN THE PROCESS OF CHECKING CRUSHER.

DURING DEMOLITION OF A SEPARATOR CHUTE, EE POSITIONED HIMSELF TO WHERE WHEN THE CHUTE WAS CUT & RELEASED, A SECTION STRUCK AGAINST HIS LOWER LEG.

EE WAS REACHING OVER THE TOP OF A FEED CHUTE TO INSERT A BOLT WHILE ANOTHER EE WHO WAS NOT AWARETHAT HIS HAND WAS IN THAT AREA, PASSED A LIT TORCH OVER THE BACK OF IT BURNING HIS HAND

EE WAS USING A HAND GRINDER CLEANING UP STEEL PLATE WHEN HE WAS STRUCK BY A STEEL CHIP IN THE LEFT EYE.

EMPLOYEE WAS LIFTING CONVEYOR BELTIN UP TO TRANSFER BOX WHEN HE STRAINED HIS LOWER BACK.

EE WAS WALKING IN THE MUD AND HIS RIGHT FOOT GOT STUCK CAUSING HIM TO FALL FORWARD INTO THE GUARD OF THE CONVEYOR. THE GUARD HAD A SHARP WIRE THAT PUNCTURED HIS LEFT THUMB.

EMPLOYEE WAS DOING ROUTINE PIT MAINTENANCE OF BELT REPAIRS ON 12-22-97. AT 4:30 PM ON THIS DAY, EMPLOYEE STARTED HAVING CHEST PAIN. THE PAIN PROGRESSED BY THE TIME HE GOT HOME SO HE WENT INTO THE HOSPITAL FOR TREATMENT AND WAS DIAGNOSED AS HAVING A HEART ATTACK.

CLEANING OUT LOWER CHAIN GUARD OF #1 FEEDER WHEN THE WATER AND DEBRIS HE WAS CLEANING OUT, ENTERED LEFT EYE.

EE WAS DIRECTING THE CRANE OPERATOR IN LIFTING CONVEYOR'S COUNTERWEIGHT WHEN THE WEIGHT BECAME UNBOUND AND SWUNG OVER AND PINCHED HIS ANKLE BETWEEN THE COUNTER WEIGHT FRAME AND COUNTERWEIGHT.

EE WAS CUTTING A 10'X10'X1/2" PIECE OF USED CONVEYOR BELTING WHENHIS KNIFE SLIPPED AS THE BLADE STARTED TO CUT THROUGH A WORN SECTION. HE WAS UNABLE TO STOP THE MOMENTUM OF HIS CUTTING STROKE AND THE BLADE ENTERED HIS LEFT THIGH.

EE WAS SHOVELING ROCK ON 3 TOWER WHEN HE FELT A SHARP PAIN IN HIS LOWER BACK.

EE LIFTED AND TURNED TO REPLACE A 3'X3' GUARD SECTION OF PC2C TAIL PULLEY WHEN HE FELT A SHARP PAIN IN HIS LOWER BACK. THE INJURY DID NOT REQUIRE MEDICAL ATTENTION UNTIL 5-1-97.

EE WAS LIFTING A 6' X 54" SECTION OF CONVEYOR BELT ONTO P7 PORTABLE CONVEYOR. WHEN HE RAISED IT UP TO SHOULDER LEVEL TO PLACE IT ON THE CONVEYOR, HE FELT A STRAIN IN HIS RIGHT SHOULDER.

EMPLOYEE CROSSED OVER 28 CONVEYOR AND WAS STANDING IN AN 8" GAP BETWEEN THE TUNNEL WALL AND CONVEYOR FRAME. HE WAS TRYING TO ADJUST THE OFF DRIVE SIDE SKIRTING OF 28 CONVEYOR FEEDERS HEAD PULL EY, WHEN HIS FINGER WAS CAUGHT BETWEEN THE HEAD PULLEY AND THE CONVEYOR BELT. THE EMPLOYEE DID NOT SHUFT DOWN OR LOCKOUT THE 28 COVNEYOR OR FEEDER BELT.

EMPLOYEE WAS POSITIONING A 12" FGEAR ON A FORKLIFT PALLET WHEN HE CUT HIS FINGER ON A GEAR TOOTH WHICH HAD A SHARP EDGE. THE CUT REQUIRED STITCHES.

EE WAS WALKING ACROSS THE MIDDLE DECK OF #1 TOWER WHEN HE SLIPPED ON LOOSE GRAVEL THAT SPILLED DOWN FROM #1 SCRUBBER & TWISTED HIS LEFT KNEE.

EE WAS WELDING PLOW BAR INSIDE 1B SCRUBBER WHEN HE STOPPED AND REMOVED HIS WELDING HOOD TO WIP THE SWEAT FROM HIS FOREHEAD. HE THEN BUMPED THE TOP OF HIS HEAD AGAINST THE SCRUBBER NOZZLE WHICH WAS ABOVE HIM.

EE WAS ON ALL FOURS USING A SHOVEL TO CLEAN OUT UNDER A PIT CONVEYOR. AS HE PUSHED HIMSELF UP TO A KNEELING POSITION. HE FELT A POP IN HIS RIGHT ELBOW.

EE WAS USING A WEDGE & DOG WHILE INSTALLING A STEEL PLATE TO RELINE THE BOTTOM OF #2 CRUSHER DISCHARGE CHUTE. AS HE WAS HAMMERING THE WEDGE, A STEEL FRAGMENT BROKE OFF THE DOG & STRUCK HIM IN THE LEFT CHEEK. THE FRAGMENT WAS REMOVED AT THE HOSPITAL E.R. & ONE STITCH WAS REQUIRED.

THE EE WAS URINATING WHILE STANDING IN THE AREA OF P2 CONVEYOR TAIL PULLEY. THE EE TURNED HIS UPPER BODY SUDDENLY TO LOOK AT THE NOISE FROM THE HEAD PULLY & THEN STRAINED HIS BACK.

THE EMPLOYEE WAS LOADING A 5' X 6" PICE OF CHANNEL IRON ONTO THE BACK OF A FLATBED TRUCK AND CCUT HIS MIDDLE FINGER WHEN HE FAILED TO REMOVE HIS RIGHT HAND OUT FROM BETWEEN THE CHANNEL IRON AN D THE REAR EDGE OF THE TRUCK BED.

EE WAS PULLING A LEFTOVER SECTION OF NEW CONVEYOR BELT AWAY FROM THE CONVEYOR FRAME WHEN HE SUFFERED A SLIGHT STRAIN TO HIS LOWER BACK. HE WAS ABLE TO WORK UNTIL 11-1-94 WHEN HE REPORTED AN IN CREASE IN PAIN AT WHICH POINT HE WAS SENT IN FOR MEDICAL TREATMENT.

EMPLOYEE WAS SITTING INT HE PORTABLE OUTHOUSE WHEN HE FELT A BITE OR STING ON TEH BACK OF HIS NECK. HE WAS UNABLE TO LOCATE WHAT BIT HIM, BUT THE DR DETERMINED IT WAS A WASP BITE.

YEMPLOYEE WAS SITTING ON #2 FEEDER CONVEYRO BELT IN FRONT OF THE FEEDER GATE WORKING ONT HE DRIVE SIDE SKIRTING. HEAVY RIAN CAUSED AN 8" ROCK FROM THE MATERIAL ABOVE THE FEEER TO BE WASHED TH ROUGHT HE OPENNING OF HT EFEEDER GATE AND STRIKE THE EMPLOYEES RIGHT KNEE.

EMPLOYEES KNEE (RT) BECAME SWOLLEN AFTER CONSTANT SQUATTING & BENDING OF THE KNEES DURING THE ASSEMBLY OF A SYMONS CONE CRUSHER

EMPLOYEE WAS USING A 2"X 2' STEEL BAR, WHICH WAS SUPPORTED BY THE FORKS OF A FORKLIFT ADN GREASED SO IT WOULD SLIDE SMOOTHLY, AS A RAM TO HAMMER OUT THE HYDRAULIC TILT PIN OF A DRESSER 560B LO ADER. THE REPETITIVE MOTION OF SLIDING THE BAR TO DRIVE OUT THE SEIZED PIN FOR 30 MIN. OVER A 45 MIN. PERIOD OF TIME CAUSED HIS BACK TO LATER STIFFEN UP.

EE WAS SHOVELING ONT FOOT OF SAND SPILLAGE FROM THE SAND TUNNEL WALKWAY NEAR 4S AND 4SA CONVEYOR TRANSFER POINT. HE LIFTED HIS HEAD AND THE HARDHAT HE WAS WEARING STRUCK THE TUNNEL'S CONCRETE CEILING, JAMMING HIS NECK.

EMPLOYEE WAS REPAIRING #1 TOWER CHUTE DIVIDER FROM INSIDE THE CHUTE WHEN HE SLIPPED AND DROPPED APPROX 2 FEET DOWN THE CHUTE. HE WAS WEARING A SAFETY BELT WHICH PREVENTED HIM FROM FALLING TO THEBOTTOM OF THE CHUTE. THE ABRUPT STOP CAUSED HIS BACK TO BECOME SORE.

EMPLOYEE COMPLETED FUELING OF DOZER AND WAS STEPPING DOWN FROM THE DOZER TRACKS, WHEN HE SLIPPED, HITTING HIS LEFT SHIN AGAINST THE DOZER ARM.

WHILE CHANING THE TAIL PULLEY OF CONVEYOR 22 PLACING IT INTO ITS FINAL POSITION THE PULLEY SHIFTED PINCHING HIS FINGERS BETWEEN THE TAIL PULLEY SHAFT AND THE CONVEYOR FRAME.

EE S RIGHT SHOULDER BECAME SORE AFTER WORKING ABOVE SHOULDER LEVEL FOR SEVERAL HOURS REPLACING 1A SCREENS OFF DRIVE SIDE BEARING. HE WAS ON VACATION 10-9-93 THRU 11-1-93 AND WHEN HE REPORTED H IS SHOULDER STILL BEING SORE AFTER HIS RETURN HEWAS SENT IN FOR MEDICAL TREAMTENT ON 11-5-93.

EMPLOYEE WAS TRYING TO CLEAR THE 1/4"X DUST GATE AT #28 CONVEYOR WHICH WAS PLUGGED UP BY REPITIOUS OPENING AND CLOSING THE GATE WHEN HIS RIGHT HAND SLIPPED OFF THE GATES HANDLE AND HIS MIDDLE FINGER STRUCK AGAINST THE STATIONERY PORTION OF THE STEEL GATE.

EE WAS USING A LONG HANDLED HOE TO REMOVE MATERIAL WHICH HAD BUILT UP UNDER A RETURN ROLLER ALONG PC5C CONVEYOR. WHEN THE HOE WAS PULLED INTO THE ROLLER CAUSING HIS MIDDLE FINGER TO BECOME CAU GHT IN THE PINCH PINT BETWEEN THE RETURN ROLLER AND THE CONVEYOR BELT BEFORE HE COULD LET GO OF THE HANDLE.

EMPLOYEE WAS USING A 4 LB SLEDGE HAMMER & CHISEL TO BREAK TEN WORN CONVEYOR LACINGS. HIS RIGHT ELBOW BECAME SORE FROM THE REPETITIVE MOTION OF SWINGING THE SLEDGE HAMMER.

EMPLOYEE S TRAINED HIS BACK 04-01-93 LIFTING RR TIES FROM FORKS OF A FORKLIFT HE AGAIN HAD ANOTHER SLIGHT BACK STRAIN 4-3-93 PULLING 1/2 COMPU TER LINE THRU CONDUIT ON 04-07-93 HE CALLED IN UN ABLE TO REPORT FOR WORK DUE TO BACK PAIN & WAS I NSTRUCTED BY HIS SUPERVISOR TO SEE A DOC

EMPL SLIPPED & FELL DESCENDING EMBANKMENT TO WORK ON #1A CONVEYOR DURING RAINY WEATHER CONDI-TIONS.

EMPLOYEE WAS CHECKING THE ENGINE OIL LEVEL OF SCRAPER #974 WHILE FUELING THE FRONT ENGINE, WHEN THE DIESEL PUMP NOZZLE CAME OUT OF THE TANK FILLER NECK AND SPRAYED HIM.

54736YEE HAD HIS LEFT FOOT ON THE UPPER EAST SIDE OF #1A SAND CLASSIFIER BOX TO STEP OUT WHEN HIS LEFT FOOT SLIPPED BACK DOWN INTO THE CLASSIFIER AND STRUCK AGAINST THE LOWER FLIGHT SECTION CA 42957 HIS ANKLE TO TWIST.

54736YEE WAS REPLACING 2A CONVEYOR RUBBER SKIRTING WHEN HIS FOOT SLIPPED OFF THE CONVEYOR FRAME AND HE FELL TO THE SAME LEVEL LANDING ON HIS RIGHT SIDE AGAINST THE CONVEYOR FRAME.

65007-11-92 EMPLOYEE CALLED IN TO REPORT THAT HE INJURED HIMSELF 07-10-92 WHEN HIS RIGHT KNEE BUMPED AGAINST #1 CONVEYOR HEAD PULLEY HANDRAIL.

EMPLOYEE WAS ON LEVEL GROUND ROLLING UP A 60' SECTION USED CONVEYOR BELT,WHEN HE STRAINED HIS BACK PUSHING THE ROLL OF BELTING FROM THE REAR.

EMPLOYEE WAS WEARING EYE PROTECTION WHILE INSIDE #1B SCRUBBER PAN REMOVING WORN SIDE PLATES DURING HIS SHIFT FROM 2:30PMTO10:30PM ON 05-28-92HE REPORTED BEING UNAWARE HE SUSTAINED AN INJURY & HAD JNO SYMPTOMS FROM HIS LEFT EYE UNTIL HE AWOKE THE MORNING OF 05-29-92

EMPLOYEE TILTED A 1'X4'X1/4" STEEL PLATE ON END AND WAS ATTEMPTING TO LIFT IT OFF THE SHOP PAD CUTTING TABLE WHEN HIS RIGHT ELBOW BECAME DISLOCATED.

AS EMPLOYEE STEPPED DOWN TO THE GROUND FROM THE LAST RUNG OF THE LUBE TRUCK LADDER,HE TWISTED HIS LEFT ANKLE ON THE UNEVEN GROUND SURFACE BELOW.

WHILE MAKING REPAIRS,EMPL WAS PULLING ON V-BELT DRIVE OF #1A ROCK WEMCO CLASSIFIER TOWARDS HIMSELF TO GET PROPER ALIGNMENT OF BULL & PINION GEARS.WHEN V-BELT SPUN FREE,FINGER BECAME CAUGHT IN SHEAVE PINCH POINT.

EMPLOYEE RIGHT BOOT BECAME STUCK WHILE STANDING IN MNUD TO PERFORM WORK ON THE SETTLING POND PIPE. AS HE LIFTED HIS LEG THE RIGHT FOOT REMAINED PLANTED CAUSING HIM TO TWIST HIS KNEE.

EMPLOYEE WAS STANDING ON A 30" X 30" UINSECURED STEEL PLATE WHICH BECAME COUNTER WEIGHTED FROM STEEL BEING UNLOADED BY A FORKLIFT. AS EMPLOYEE STEPPED OFF THE PLATE IT FLIPPED OUT FROM UNDERNE ATH HIM AND CAUSED HIM TO FALL TO THE SAME LEVEL AND STRIKE HIS BACK AGAINST A 6" BEAM.

EMPLOYEE WAS STEPPING DOWN 28" FROM A DOZER ARM AND HIS RIGHT FOOT LANDED ON THE TOP OF A 1" AIR HOSE HE WAS USING TO POWER HIS IMPACT GUN, CAUSING HIM TO TWIST HIS RIGHT ANKLE.

EMPLOYEE WAS USING A PORTRA POWER TO LINE UP BOOM SHEAVE BORE ON A 38B BUCYRUS ERIE CRANE PORTRAPOWER HEAD WAS PUSHING AGAINST THE SIDE OF THE BOOM WITH A CHAIN ATTACHMENT & CHAIN WRAPPED AROU ND THE BOOM POINT EMPLOYEE STOPPED THE PUMPING TO INSPECT THE BORE ALIGNMENT WHEN THE PORTA POWER HEAD SLIPPED OUT OF POSITION & STRUCK HIM

EMPLOYEE WAS PLACING A 6' LONG 2" X 12" WOODEN PLANK UNDER #1A CONVEYOR BELT TO REPAIR BROKEN LACINGS WHEN A SMALL SILVER ENTERED THE MIDDLE FINGER OF HIS RIGHT HAND.

EE REPORTED ON 7-19-91 THAT HE INJURED HIS BACK ON 7-18-91 CARRYING A COME A LONG 150 YEARDS TO 1 TOWER HE AWOKE THE MORNING OF 7-20-91 FEELING PAIN IN HIS LOWER BACK AND LEFT LEG AT WHICH POI NT HE WENT FOR MEDICAL TREATMENT.

EMPLOYEE WAS SITTING DOWN FILLING #16 CONVEYOR GEAR BOX WITH OIL USING ONE GALLON CONTAINERS WHEN HE STARTED TO FEEL SOME PAIN IN H IS BACK AFTER FILLING THE GEAR BOX WITH OIL HE TOOK HIS SCHE DULED BREAK THRU OUT WHICH THE PAIN INCREASED TOTHE POINT WHERE HE WAS UNABLE TO RETURN TO WORK

EMPLOYEE WAS CLEANING STEEL TO BE CUT INSIDE THE HEAD PULLEY PAN OF #18 CONVEYOR. HE WAS BRUSHING THE STEEL WITH HIS WELDING GLOVE AND THE WIND BLEW A PIECE OF RUST INTO HIS LEFT EYE.

EE INSTALLED HIS LOCK OUT LOCK ON 21A CONVEYOR TO PREFORM A BELT SPLICE. WHILE HE WAS WORKING ON THE SPLICE A SECOND EE TRIED TO START 22 CONVEYOR. BECAUSE THE CONVEYORS WERE MISLABLED 21A CON VEYOR WAS ENERGIZED AND MOVED FIVE FEET.

EMPLOYEE'S FINGER WAS CAUGHT BETWEEN HAMMER HEAD AND TOP EDGE OF ROAD SIGN WHILE HAMMERING POST INTO THE GROUND.

EMPLOYEE WAS LIFTING CORNER OF RUBBER SCREEN CLOTH SECTION AND WAS ABOUT TO START DRAGGING IT ON CONCRETE SURFACE WHEN HE FELT PAIN IN HIS LOWER BACK.

HOLDING HEAD OF CUTTING EDGE BOLT LOCKED IN PLACE IMPACT WRENCH ON NUT CAUSED BOLT TO SPIN AND CUT THROUGH GLOVE IN PALM OF R HAND

EMPLOYEE WAS REMOVING TOP PULLEY SECTION OF FUEL ISLAND AIR HOSE COUNTERWEIGHT PIPE WHILE STANDING ON FORKLIFT WORK PLATFORM.PULLEY SLIPPED FROM RIGHT AHND AND TIP OF LEFT INDEX FINGER WAS CAU GHT BETWEEN RETURN CABLE WHICH WAS ATTACHED TO PULLEY AND TOP OF COUNTERWEIGHT PIPE.

EMPLOYEE HAD ADJUSTMENT LOCK POST OF CONE CRUSHER TURN UNKNOWINGLY WITH TAPER KEY INSERTED AND PINCH FINGER TIP OF LEFT INDEX FINGER BETWEEN HOPPER BOWL AND TAPER KEY WHILE HE WAS REACHING WIT H RIGHT HAND TO PICK UP HAMMER TO TIGHTEN TAPER KEY.

LIFTED HOOD TO CHIP SLAG AND SLAG FLEW IN L EYE

PULLING BOTH HANDS AWAY FROM STEEL CUTTING L EBLOW BUMPED SPRAY BAR BEHIND HIM, LIT TORCH IN L HAN D TO ENTER GLOVE OF R HAND AND BURN WRIST

AIR HOSE GLAD HAND FITTING TWISTED LOOSE FROM 1" IMPACT GUN,BREAKING SAFETY WIRE AND STRUCK EMPL ON RIGHT SIDE OF HIS FACE.

EMPLOYEE WAS SHOVELING MATERIAL OFF SC7 CONVEYOR AT TAIL PULLEY WITH ONE FOOT ON THE BELT AND THE OTHER FOOT ON REAR TAIL PULLEY GUARD. GUARD BROKE CAUSING EMPLOYEE TO LOSE HIS FOOTING AND FAL L 4' TO GROUND.

EMPLOYEE WAS STANDING IN UNAUTHORIZED AREA ON A WOODEN PLANK 8FT HIGH WITHOUT A SAFETY LINE WASHING OUT PC2C HEAD PULLEY PAN WHEN HE SLIPPED HE HIT HIS BACK AGAINST A PIECE OF ANGLE IRON AS HE FELL

EMPLOYEE SAID HIS HIS BACK FELT SORE AFTER SHOVELING #2 FEEDER AND THEN WAS LATER AGGRAVATED WHEN LIFTING GUARD FROM #P-2 CONVEYOR. INJURY NOT REPORTED UNTIL 2/26/90.

WHILE USING IMPACT GUN, EMPLOYEES LEFT HAND WAS OVER CUTTING EDGE BOLT HEAD. WHEN IT BROKE LOOSE, IT SPUN AND CUT HIS MIDDLE FINGER.

EMPL RIGGING CABLES FOR DOZER TO PULL 100' PORTABLE CONVEYOR.AREA WAS VERY WET & MUDDY.EMPL TOOK A STEP,RUBBER BOOT STUCK IN MUD.EMPL FELL FORWARD AND PULLED CALF MUSCLE IN LEFT LEG.IN 45 MIN PAIN SEEMED TO RUN UP & DOWN ENTIRE LEG.

EE WAS CHIPPING WELDING SLAG WITHOUT WEARING HIS SAFETY GLASSES.

EMPLOYEE WAS LIFTING ONE SIDE OF 50 TON FLOOR JACK WITH HELP OF CO-WORKER ON OPPOSITE END WITHOUT FIRST STRETCHING BACK MUSCLES

EMPL DESCENDING CATWALK #7 CONVEYOR.LOST HIS BALANCE AND SLIPPED ON CATWALK .EMPL SPRAINED RIGHRT HAND.THINKS HE MUST HAVE BUMPED HAND BY REACHING FOR HANDRAIL TO STOP HIS FALL BUT DOESNT REME MBER HITTING IT.EMPL DIDNT KNOW UNTIL 2 HRS LATER THAT HAND WAS SPRAINED.

WASHING FLOOR OF FEEDER USING WATER HOSE PULLING HOSE AROUND TO WASH FLOOR SLIPPED ON WET FLOOR.

EMPL WAS REPOSITIONING A LIGHTING STAND FOR WORK ON THE CONVEYOR THE LIGHT STAND IS APPROX 65LBS TO REPOSITION THE STAND THE MEPL WAS DRAGGING IT WHILE DRAGGING THE STAND HE FELT SUDDEN PAIN I NLOWER BACK

EE WAS SHOVELING BUILT UP MATERIAL FROM UNDER P-3 CONVEYOR WHILE SITTING ON HIS KNEES. EE TURNED RIGHT TO THROW MATERIAL OFF SHOVEL AND STRAIN HIS BACK.

MATERIAL IN SCREEN PAN SLID DOWN CAUSING HIM TO LOOSE FOOTING AND HIT LOWER R. LEG AGAINST SIDE OF PAN.

EMPLOYEE WAS SHOVELING SAND FROM UNDER 4SA CONVEYOR NEAR 18 GATE WHEN SOME SAND STUCK TO THE END OF HIS SHOVEL BLADE AS HE WAS TRYING TO EMPTY IT CAUSING HIM TO OVER EXTEND & STRAIN HIS MIDDLE BACK

EMPL WAS KNEELING AT DISCHARGE END OF #2A SCREEN AFTER DRAINING OIL FROM SCREEN. EMPL HAD 5 GAL BUCKET ABOUT 3/4 FUL OF OIL APPROX 31 LBS. EMPL PUT ONE HAND ON WALKWAY PLATFORM & SET BUCKET OF OIL ONPLATFORM WITH OTHER HAND. HE FELT PAIN INLOWER BACK WHEN SETTING BUCKET ON PLATFORM.

EMPLOYEE HAD REMOVED A LINK FROM A DRIVE CHAIN ON A SMALL FEEDER, AND WAS IN PROCESS OF RECONNECTING THE CHAIN. THE EMPLOYEE WAS HOLDING UP THE LINK WITH LEFT HAND & HAMMERING IN THE LINK WITH HIS RIGHT HAND. THE CHAIN SLIPPED AND THE EMPLOYEE HIT THE TIP OF HIS FINGER WITH THE HAMMER.

EMPL WAS PERATING TD-40 DRESSER DOZER AT APPROX 1:00 PM EMPL WHILE PERATING DOZER FELT PAIN IN RIGHT SHOULDER.

EMPLOYEE WAS PULLING A TRACK ADJUSTMENT CYLINDER FROM THE LEFT SIDE OF A DRESSER TD-40 DOZER THE CYLINDER IS MADE WITH A SQUARE END AT THE BACK AND THE DOZER A SQUARE HOLE AT THE BOTT OM OF THE FRAME. WHEN PULLING ON THE CYLINDER OUT OF FRAME SQUARE END DROPPED INTO HOLE PINCHING EMPLOYEES INDEX FINGER BETWEEN CYLINDER AND FRAME.

EMPLOYEE CALLED WORK THE NEXT MORNING AFTER HIS SHIFT HAD FINISHED HE HAD SORENESS IN HIS MID BACK THE EMPLOYEE HAD TAKEN UP A CRUSHER SHOVELED UNDER A CONVEYOR BELT AND RUN A SMALL DOZER DUR ING HIS SHIFT HE DOES NOT RECALL ANY INCIDENT HURTING HIS BACK BUT FELT THA T ONE OF THE ABOVE ACTIONS CONTRIBUTED TO THE SORENESS

EMPLOYEE WAS DESCENDING A LADDER FROM ENGINE PLATFORM OF A CAT 637D SCRAPER WHEN HE REACHED SECOND RUNG FROM FLOOR LADDER SLIPPED OUT FROM UNDER HIM EMPLOYEE STRAINED HIS LEFT SHOULDER LADDER WAS NOT EQUIPPED WITH SAFETY SHOES WAS NOT A CO.LADDER & HAD BEEN BORROWEDD BY EMPLOLYEE FROM THE VEHICLE OF ANOTHER EMPLOYEE THE 637D IS EQUIPPED WITH AN ACCESS LADDER

EMPLOYEE WAS ASSISTING IN THE ADJUSTMENT OF A 4 1/4 FT NORDBERG STATNDARD CONE CRUSHER EMPLOYEES WERE ADJUSTING THE CRUSHER WITH A HAND CHAIN HJHOIST THE CHAIN BROKE AND HIT ONE OF THE EMPLOYE S IN THE LOWER RT LEG CAUSING CONTUSIONS AND LACERATIONS TO THE LEG

EMPLOYEE IS A WATER TRUCK DRIVER HE HAD STOPPED HIS TRUCK AND WAS CLIMBING DOWN OFF OF THE TRUCK WHEN HE STEPPED TO THE GROUND HE STEPPED ON A LOOSE MOUND OF DIRT ANDT WISTED HIS ANKLE

THE EMPLOYEE ST5RTING UP THE CRUSHING CIRCUIT AND HAD ALRADY STARTED CONVEYOR. THE EMPLOYEE NOTICED THE CONVEYOR BELT WIPER HAD SOME MUD STICKING TO IT. THE BELT WIPER IS MOUNTED TO THE UNDE RSIDE OF THE BE5T AND HAS A COUNTER WEIGHT ARM SATTACHED TO KEEP THE WIPER TIGHT AGAINST THE BELT. THE EMPLOYEE LIFTED THE COUNTER WEIGHT ARM AND DROPPED IT TO KNOCK THE MUD OFF THE WIPER. W

EMPLOYEE WAS CA9RYING A 10 FT PIECE OF 3/4 INCH X 2 INCH STEEL BAR APPROX 51 LBS INTO 1 SCRUBBER FOR MAINTENANCE. WHILECARRYING THE PIECE OF BAR INTOT HE SCRUBBER, THE EMPLOYEE FELT PAIN IN HI S LOWER BACK. 3

EMPL USING 1'' 5IR IMPACT GUN TO REPLACE CUTTING EDGES ON LOADER.RETAINER PIN FOR SOCKET BEGAN TO SLIP OFF EMPL GRABBED SOCKET ..CUT HAND ON RETAINER PIN.

EMPL CUTTING ST9EL BAR THEN HUNG IGNITED CUTTING TORCH FROM WALKWAY HANDRAIL.WHEN HE QUICKLY REACHED FOR PIECE OF STEEL BAR HE HAD KNOCKED OVER HE BURNED BACK OF LEFT HAND ON TORCH.THIS EMPL W ASNT QUALIFIED 3OR INSTRUCTED TO USE CUTTING RTO/// TORCH AND VIOLATED COMPANY SAFETY RULE.

EMPLOYEE WAS RE4OVING A CONVEYOR TROUGHING ROLLER FROM CONVEYOR. AFTER REMOVING THE ROLLER THE EMPLOYEE THREW THE ROLLER OVER THE HANDRAIL TO THE GROUND. UPON THROWING THE ROLLER THE EMPLOYE E NOTICED PAIN 3N HIS BACK.

EMPLOYEE WAS RE4OVING ROC GUARDS FROM A DRESSER TD-40 DOZER USING A 1 IN AIR IMPACT WRENCH THE WORKING AREA THAT THE EMPLOYEE WAS WORKING IN HAD LIMITED HEIGHT AS THE EMPLOYEE SET THE IMPA CT WRENCH DOWN 7HE IMPACT WRENCH SLIPPED AND CAUGHT HIS RT HAND BETWEEN THE CONCRETE FLOOR AND THE WRENCH

EMPLOYEE WAS CL9ANING UP A WORK AREA AFTER A RECENT CRUSHER LINER CHANGE. THE USED HEAD LOCK NUT FROM CRUSHER HAD A VERY SHARP UNDERSIDE DUE TO THE NUT WEAR. WHILE MOVING THE LOCK NUT THE EM PLOYEE BUMPED T2E NUT AGAINST HIS LEFT FOOT. THE SHARP EDGE OF THE NUT CUT THROUGH THE LEFT BOOT AND INTO THE LEFT FOOT.

EMPLOYEE WAS RE4OVING A BELT CLEANER FROM A CONVEYOR EMPLOYEE WAS BENDING OVER AND LIFTING TO PULL THE CLEANER OUT FROM THE CONVEYOR TRUSS HE WA ALSO HAD HELP FROM ANOTHER EMPLOYEE ON THE OTHE END OF THE WIPE9 THE NEXT DAY HE FELT SORENESS IN HIS UPPER BACK

EMPL SITTING ON3STEEL BOX 18'' HIGH LAYING ON THE GROUND.THE BOX WAS OPEN INTHE FRONT AND HAD STEEL PLATE NOT ATTACHED SITTING ON TOP.EMPL MOVED AND PLATE FELL DOWN INTO THE BOX CAUSING ABRASI ON ON EMPL LOWE9 BACK.

EMPLOYEE WAS RE4OVING A WATER HOSE FROM HIS WORK AREA UNDER #2 SCREEENING TOWER.WHILE REMOVING THE HOSE,THE EMPLOYEE ACCIDENTALLY STEPPED ON THE HOSE AND TRIPPED,CAUSING STRAIN TO HIS LOWER BA CK. 3

EMPLOYEE WAS US3NG A STEEL BAR TO HAMMER ON A SAND CHUTE WHICH HAD BECOME PLUGGED. WHILE HAMMERING ON THE CHUTE, THE EMPLOYEE FELT PAIN IN HIS MID-BACK.

EMP WAS USING L2NG HEAVY DUTY 1-INCH HIGH PRESSURE HOSE TO WASH DOWN WEMCO FROM DECK ABOVE. HOSE WAS COILED OR LAID ABOUT ON DECK. AS HE WASHED WEMCO, THE HOSE SLID DOWN FROM THE D ECK AND DOW N THE SIDE OF 7HE WEMCO, TRANCFERRING WEIGHT ON TO HIM AND PULLING AGSINST HIM

EMPLOYEE WAS ST5NDING OUTSIDE CONTROL ROOM WATCHING THE PLANT RUN.A SECTION OF METAL PIPE 1 1/2 INCH IN DIAMETER X 10 FT LONG WAS STANDING ON END LEANING AGAINST THE WALL.THE PIPE FELL HITTING EMPLOYEE ON THE3END LEANING AGAINST THE WALL.THE PIPE FELL HITTING EMP. ON THE RIGHT FRONT SIDE OF HIS HEAD. HE WAS WEARING HIS HARD HAT AT THE TIME.

EMPLOYEE WAS US3NG SHOVEL TO REMOVE PACKED SAND & GRAVEL FROM #6 SCREEN PAN WORK AREA WAS CRAMPED HE HAD TO WORK FROM SQUATRTING TO STANDING POSITION TO MOVE MATERIAL AS HE SHOVELED HE STRUCK HIS RIGHT ELBOW3AGAINST BACK OF SCREEN PAN INFLICTING HAIRLINE CRACK IN ELBOW

EMPLOYEE WAS LA2ING ON SCREEN DECK IN VERY CRAMPED QUARTERS INSTALLING SCREEN TENSION RAILS.HE TURNED HIS HEAD AND FELT HIS NECK POP.

EMPLOYEE WAS WO9KING FROM AN ELEVATED POSTION LEANING OVER THE FRONT END OF A DOZER LOOSENING BOLTS ON DOZER RADIATOR IN PREPRATION FOR REMOVAL OF THE RADIATOR. HE PULLED HARD ON A WRENCH AND FELT PAIN IN H3S BACK.

EMPLOYEE ATTEMP7ED TO ROLL OVER A SECTION OF CONVEYOR TRUSS BY LIFTING TOP OF ONE END THEN PUSHING IT OVER ROLLING IT.

EMPLOYEE STATED3HE WAS INJURED BECAUSE HAMMERING ON SCREENS IN THE MILL TO REMOVE BUILT UP MATERIAL CAUSED SORENESS IN BOTH ELBOWS AND RIGHT SHOULDER. HE HAS BEEN UNDER MEDICAL TREATMENT FOR P AST TWO OR THRE9 YEARS FOR TENDONITOUS NOT RELATED TOHOIS WORK. HE HAS NOT REPORTED ANY PROBLEMS WITH THIS SITUATION BEFORE.

EMPLOYEE WAS IN3Y CHUTE ON #1 TOWER INSPECTING IT FOR HOLES ROCK SPILLED OVER FROM SCRUBBER ABOVE EMPLOYEE SLIPPED IN CHUTE TRYING TO GET OUT OF CHUTE SLID DOWN CHUTE AND DROPPED TO CONVEYOR B ELT BELOW ABOUT35 FT BELT WAS NOT OPERATING

EMPLOYEE WAS AT7EMPTING TO INSTALL A DUMBELL(A SHAFT WITH FLANGES ON EITHER END)ON TO #2 FEEDER.HE HAD INSERTED THE FAR END OF THE SHAFT INTO THE BEARING AND WAS POSITIONING THE REAR REAR END WHEN THE FAR EN8 SLIPPED OUT OF THE BEARING AND FELL, HITTING HIS RIGHT THUMB,FRACTURING IT.

INJURED EMPLOYE9 WAS PULLING ON A CABLE ON THE BOOM OF A LINK BELT DRANE TO TAKE UP SLACK AS CRANE OPERATOR SLOWLY LET OUT CABLE CABLE HUNG UP THEN SUDDENLY RELEASED WHIPPING AND PINCHING LEFT HAND OF INJURE8 EMPLOYEE BETWEEN CABLE AND SHEAVE.

INJURED EMPLOYEE & ANOTHER EMPLOYEE WERE LIFTING AN IMPACT TROPHING ROLLER WEIGHING APPROX 120LBS INJURED EMPLOYEE WAS ON A WEIGHT LIFT RESTRICTION OF 50LBS FOR THE PAST YEAR HE ACKNOWLEDGED T HIS LIFT WAS TOO HEAVY BUT HE TRIED IT ANYWAY

EMPL NOT SURE W2AT HAPPENED.WAS WALKING THROUGH PLANT.BENT OVER TO PASS BENEATH CONVEYOR BELT.NOTICED PAIN IN PELVIC AREA WHEN HE STRAIGHTENED UP.

INJURED EMPLOYEE WAS STEPPING DOWN FROM RUBBER TIRED MOBILE HYDRAULIC CRANE. AS HE STEPPED TO THE GROUND WITH HIS LEFT FOOT HE STEPPED ON A ROCK, TWISTING HIS ANKLE.

EMP WAS BENEATH #1 TOWER OF GRA V EL MILL USING USING WATER HOSE TO WASH DOWN SLAB. A PIECE OF METAL FELL FROM SOME AS YET UNIDENTIFIED LOCATION ABOVE AND STRUCK HIM ON THE HARD HAT AND G RAZED THE LEFT SIDE OF HIS FACE. AFTER BEING EXAMINED AT ER OF HOSP. EXPLOYEE RETURNED TO WORK. SUBSEQUENTLY HAS BEEN OFF WORK AND UNDERGOING FURTHER TESTING

EMPLOYEE WAS REPAIRING CHUTES ON #1 TOWER OF MILL WHILE MOVING ABOUT IN THE CHUTES HIS FOOT SLIPPED CAUSING HIM TO FALL FLAT ON HIS BACK IN THE CHUTE

EE WAS LAYING OUT HOSE LINE FROM COMPRESSED GAS CYLINDERS TO JOB LOCATION SCREEN DECK OF #1 TOWER IN MILL IN PREPARATION TO USE CUTTING TORCH & WALKED INTO A PROJECTING METAL SUPPORT OF A TEM PORARY WALKWAY SUSTAINING A CONTUSION OF THE HEAD. HE FELT DIZZY. HE HAD REMOVED HIS HARD HAT TO CRAWL INTO A SMALL AREA.

EMPLOYEE WAS ADJUSTING TAKE-UP BEARING ON CONVEYOR WHILE PULLING ON WRENCH IT SLIPPED OFF OF ADJUSTING NUT. EMPLOYEE FELL ON WORK PLATFORM, STRUCK BACK AGAINST CONVEYOR FRAME.