S W Barrick & Sons: 1 muerte registrada Metal/Non-Metal

Employee was working on screen doing a product screen change. EE was working with another employee. EE was in the hopper under the screen removing hardware for center hold down strip when a rock fell through the screen hitting them in the back of the neck.

Cleaning up a weld with a chipping hammer a piece of slag flew up under the helmet and caused irritation to the eye.

Misjudged the height of the step into the time clock room, lost balance and fell.

Attaching a cylinder to the blade of a dozer ---when the pry bar slipped and the cylinder smashed the tip of the Emp left middle finger --- requiring stitches.

While wrenching on a cylinder on a piece of equipment the wrenches pressed together and cut into the nail and tip of the mechanic's rt ring finger requiring stitches.

While greasing the cylinder on the Dozer the cylinder head did not appear to be getting the grease. The employee looked over the cylinder head grease fitting and it popped off and struck EE in the right eye

Employee was getting out of vehicle. There was a slick spot. Employee slipped and fell causing injury to left hip.

Emp was hitting shoe on a blow bar and hit a hard surface, a piece of steel struck and cut EE's finger. EE got 1st aid and continued to work. Emp worked until 9-28-2020 when they found a piece of steel in EE's finger and had it removed. EE then went on RD as of 9-29-2020.

While getting off the loader, the employee, slipped on step (did not fall) and strained back. Employee went back for a follow up on 11/22/2019 and P.T. was recommended... on 11/25/2019 Employee signed up for P.T. --- making this injury reportable.

Emp suffered a burn to left hand while heating up an elbow. EE used bare hand to re position it.

A rock (football size) rolled down and off a catwalk, striking the ground person in the back as EE was bending over shoveling. EE went to the clinic and was put on restricted duty with a bruise to the lower left side of EE's back.

Contractor Employee was working on tracks of excavator and had to remove built up dry dirt to get to the bolts. As they were scrapping the dried dirt, a small sliver of metal became embedded into the left forearm

Employee was traveling down a ladder, tripped and struck right knee on block ... reported injury on 7-28-17. Emp went to Clinic and was put on restrictions. Emp doing regular job (missing no time) but working with-in restrictions.

Employee was inside a head-box cleaning it out. As employee went to exit the box employee felt a strain in employee's back.

Employee injured knee when employee slipped climbing up an excavator to fuel it. This slip / injury happened on 6/2/17. Employee continued to work (after receiving 1st Aid) and worked without issue until employee woke-up on July 5th in pain. On July 5th employee had knee drained and was back to full duty on the 10th of July.

Employee was lifting a 50 pound 20 foot long piece of angle iron and felt a muscle pull in rib cage. Employee went to clinic and returned to work with lifting restrictions.

Employee was climbing on to the 1st step of haul truck and went to place wheel chalk in place....ee slip and fell 18 inches and fractured left wrist

Inspecting the Dozer, Employee was dismounting the Dozer and slipped, spraining EE's left knee. Employee reported the sprain to management immediately. Employee and management decided in house 1st aid was enough. It was later decided (on 3-25-16) to seek professional help.

Employee was standing on unstable ground...lost balance and grabbed for near by pipe for support. Employee's ring caught the angle iron that was supporting the pipe and almost tour his ring finger off.

WHILE TWISTING AND PULLING ON A BLOCKED TRANSMISSION (WORKING UNDER A WATER TRUCK) EMPLOYEE FELT A POP IN HIS LEFT SHOULDER

Employee was stepping off a deck onto a portable ladder, the ladder shifted, the employee slipped and injured his rt knee.

Employee was repairing a tear in a conveyor belt. While pushing down on the belt clip a sharp edge, his rt index finger was cut

Employee slipped and fell to his left knee while walking down a dirt road. The road had a few ruts in it due to rain. Employee stepped next to a rut that gave way and caused him to lose his balance and fall to his knee.

Employee was working with a partner taking out bolts on the primary crusher wear bar. one employee was working the ratchet while the other supported the socket. As the socket started to slip off the bolt the employee who was injured reached to support the socket when the socket slipped off the bolt and the employee was struck by the ratchet... injuring his rt thumb.

Employee failed to use the proper tool when lining up 2 pipes and caught his finger in the gap, cutting the tip of the left index finger.

Employee was using a knife to open up a package of soap stone and cut left hand pinky finger... requiring 4 stitches.

Employee was removing a bucket pin and lost control pinching his finger.

Employee was removing load cells from a platform scale and the scale shifted and caught the tip of the index finger and severed approx. 3/8" of the finger.

Employee was drilling pre-existing holes on a hinge when the drill caught, spun around and hit the employee's finger

Two employees were carrying a bearing when employee lost his balance, fell against the handrail and felt a pain in his back.

Employee was changing screens and pulled a muscle in his back.

Employee was cutting skirt rubber when the blade slipped and cut his finger

Employee started to climb in the loader and felt something pop in his back.

Employee said he hit a bump in the road and the seat bottomed out. He felt a pain in his back sometime during the day. He did not report it until the next morning.

Employee bent over and felt a pain in his back

Employee was cutting a belt and the knife slipped and cut his little finger.

Employee was carrying a gear box and injured his back.

Employee was shoveling and hurt his back.

Employee was changing differential oil on a Cat 775 and stood up and stuck his head, causing a small cut.

Employee was changing impact bars on a crusher. He attempted to block the rotor with a pry bar and the bar pinched his finger against the frame.

THERE WAS A LEAK IN THE ACETYLENE TORCH HOSE. EE DID NOT EXAMINE HOSE. (IGNITED ACETYLENE BURNED RIGHT FOREARM.)

EE WAS USING A SHORT HANDLED HOE TO PUSH THE SKIRTING RUBBER BACK ONTO BELT #37. THE HOE SLIPPED CAUSING HIM TO STRIKE HIS HAND ON A RETURN ROLLER BRACKET CUTTING HIS FINGER.

CRAWLING UNDER BELT #13 TO GAIN ACCESS TO BELT #11. STOOD UP TOO SOON AND STRUCK HEAD ON THE FRAME OF BELT #13.

EE WAS ATTEMPTING TO WASH OUT A SCREW CONVEYOR AND SLIPPED STRIKING HIS RIGHT KNEE ON A SCREW FLIGHT.

EMPLOYEE WAS STANDING ON 4TH ROW STEP TAKING OFF #3 BELT ROLLER WHEN THE WRENCH SLIPPED OFF CAUSING EMPLOYEE TO FALL.

EE WAS ATTEMPTING TO DISLODGE BUILT UP MATERIAL IN THE SCREEN CHUTE WHEN MATERIAL CAME LOOSE AND STRUCK HIS LEG.

EE WAS INSTALLING POLYDECK PANELS USING A HAMMER. WHEN EE STRUCK THE PANEL A PIECE OF METAL ENTERED HIS EYE.

EE WAS CLIMBING UP A LADD4ER & HIT HIS KNEE

EMPLOYEE WAS TRIMMING A URETHANE SCREEN WITH A UTILITY KNIFE PULLING IT TOWARD HIMSELF WHEN IT SLIPPED OFF THE SCREEN AND CUT HIS WRIST.

EE WAS OPENING DOOR ON CRUSHER HE PUT A BAR BETWEEN DOOR AND HOUSING AND BAR SLIPPED OUT CAUSING HIM TO FALL & TWIST KNEE.

EMPLOYEE WAS ON A RAILCAR WHILE IT WAS BEING LOADED WHEN MATERIAL CAME OUT ALL AT ONCE AND STRUCK RAILCAR TIPPING RAILCAR, CAUSING THE EMPLOYEE TO BREAK ELBOWS AND WRIST.

HE GOT IN DOZER AND WAS SETTING DOWN AND DOOR SHUT ON HIS THUMB.

EMPLOYEE WAS GETTING OFF EQUIPMENT AND HIS FOOT SLIPPED ON THE STEP,HE REACHED FOR THE OTHER STEP TO CATCH HIMSELF AND CAUGHT HIS RING ON THE STEP.

EMP WAS TRYING TO GET FROZEN MATERIAL OUT OF THEHOPPER USING A DIGGING BAR. IT SLIPPED OFF THE ANGLE IRON HE WAS PRYING AGAINST AND CAUGHT HIS HAND BETWEEN IT AND THE SENSOR SWITCH.

EMPLOYEE WAS GOING TO FUEL UP HIS TRUCK. HE WAS TAKING THE CAP OFF WHEN HE TURNED AROUND AND SLIPPED ON SOME LOOSE GRAVEL CAUSING HIM TO FALL AND ROLL UNDER HIS TRUCK.

WELDING ON CHUTE UNDER #1 SCREEN.FLIPPED HIS WELDING HELMET UP AND SOME OF THE HOT SLAG POPPED OFF OF THE AREA HE WAS WELDING INTO HIS RIGHT EYE AND WOULD NOT COME OUT.

EMPLOYEE WAS ATTEMPTING TO CLEAN A ROLLER WHEN THE BELT CAUGHT & CUT HIS RIGHT FOREARM.

THE LOADER OPERATOR, FOR THE SALES YARD, WAS CLEANING HIS FRONT WINDOW WHEN HE SLIPPED AND HIT HIS CROTCH ON THE RAILING OF THE LOADER.

ROCK BECAME STUCK IN CRUSHER TOOK FOOT TO LOOSEN. ROCK MOVED, CRUSHER STARTED AND TOOK FOOT ALONG DOWN IN BESIDE OF CRUSHER.

STEPPED OUT OF TRUCK CAUSING PAIN TO LEFT ANKLE.

STONE HAULING TRUCK UPSET ON QUARRY INCLINE DUE TO LOSS OF POWER.