Buscar en el registro

EE WAS MOVING A BARREL OF OIL WITH A BARREL CART. THE BARREL SLID OFF THE FEET OF THE CART & PARTLY TIPPED OVER SO AS TO BE LEANING ON AN ANGLE OF ABOUT 45 DEGREES. HE TOOK HOLD OF THE BARREL & STOOD IT BACK UP. IN DOING SO HE FELT A STRAIN IN HIS GROIN. HE WENT TO THE DOCTOR WHO TOLD HIM HE HAD A MINOR HERNIA. HE WAS RELEASED FOR LIGHT DUTY.

INJURED AND OTHER EE WERE REPLACING TROUGH ROLLERS ON THE SAG MILL FEED BELT. EE WAS ON THE EAST SIDE OF THE BELT. THEY WERE REMOVING A WORN ROLLER ASSENBLY, THE BELT HAD LIFTED WITH COME-A-LO NG. WHEN THE WORN ROLLER WAS TIPPED OVER INJURED'S RIGHT INDEX FINGER WA CAUGHT BETWEEN THE BELT ROLLER ASSEMBLY AND THE BELT FRAME WORK.

EE WENT OUTSIDE OF THE BUILDING TO START HIS DAILY CLEAN UP, WHEN HE BENT OVER TO PICK UP A WATER HOSE HE FELT PAIN IN HIS LOW BACK. ON 8-30-02 THE EE WENT TO A DR, THE DR TOLD EE TO RETURN TO WORK, THE PAIN WAS A SPASM, THE DR DID NOT DO AN EXAMANATION. ON 8-31-02 THE EE RETURNED TO THE DR, THE DR PLACED EE ON LIGHT DUTY FOR ONE WEEK.

EE WAS CHANGING OUT A BALL CHIP DRUM, THE MOTOR ON THE TROLLY WAS NOT WORKING, THIS MADE IT NECCESSARY TO PUSH THE DRUM TO THE END OF THE BOOM BY HAND. AFTER THE DRUM WAS CHANGED SHE STARTED T O WASH SOME PRODUCT SPILL OFF THE FLOOR. SHE WASHED OFF AND ON APPROXIMATELY TWO HOURS. AFTER WASHING SHE EXPERIENCED PAIN IN HER RIGHT HIP AND SHOULDER. IT IS NOT KNOWN WHICH CAUSED THE PAIN

EE WAS REPAIRING THE CHUTE ON 4896 BELT LINE. WELDING A PLATE ALONG THE BOTTOM OF CHUTE. HE WELDED ONE END OF PLATE TO THE CHUTE, THEN USED A WELD ON CLAMP TO PULL THE GAP OUT OF THE OTHER END . THE WELD HOLDING THE CLAMP BROKE, RELEASING THE GREE END OF THE PLATE FORCING HIS HAND BACK AGAINST THE OPPOSITE SIDE OF THE CHUTE.

DURING SWING SHIFT, EE OVER-EXERTED HIMSELF FOR SEVERAL DAYS BY SHOVELING ROCK & CONCRETE. EE ALSO HAS DEGENERATIVE DISC DISEASE, WHICH COULD CONTRIBUTE TO HIS BACK PROBLEMS.

NOTICE OF POSSIBLE HEARING STS. A RETEST IS REQUIRED BUT NOT POSSABLE IN THIS CASE. THIS EE HAS DECEASED SINCE THE TIME OF THE TEST AND THE NOTIFICATION.

0N 1/5/02 EE WAS WORKING IN FEEDER BREAKER. APPOROX 10:30AM HE BREATHED IN SOME SMOKE THAT CAME FROM HIS SHOE AFTER HE HAD STEPPED ON A HOT PIECE OF METAL. THE HOT METAL WAS SLAG/SCRAP FROM AN OXYGEN/ACETYLENE CUTTING JOB HE HAD JUST PERFORMED. SUPERVISOR WENT TO PICK UP INJ EE FOR LUNCH ABOUT NOON & SAW THAT EE LOOKED ILL SUPERVISOR ASKED EE IF HE WAS OK: EE ANSWERED IT WAS JUST

EE, A MINE OPERATOR WAS ATTEMPTING TO REMOVE A USED RIPPER TOOTH FROM A DOZER RIPPER SHANK BY HITTING IT WITH A SLEDGEHAMMER. A SMALL SLIVER CAME OFF OF THE RIPPER TOOTH AND HIT THE EE IN THE LT. SHIN AND FOOT CAUSING A LACERATION. THE ATTENDING DR. APPLIED SOME SUTURES TO CLOSE THE CUT.

EE WAS HELPING THE ELECTRICAL DEPT. PULL WIRES THRU A CONDUIT ALONG THE SIDE OF #4894 CONVEYOR BELT. THE WIRES HUNG UP THEN CAME LOOSE. AS THE WIRES CAME LOOSE EE STEPPED BACK TO MAINTAIN HIS BALANCE. EE S FOOT HIT A BELT SUPPORT BEAM ON THE GROUND CAUSING HIM TO FALL BACKWASRD. THE SUDDEN SLACK INT HE ROPE THAT WAS ATTACHED TO THE WIRES THAT WERE BEING PULLED THRU THE CONDUIT CAUS

EE WAS CLEANING OUT SOME DIRT FROM UNDER ONE THE METAL PURLIN. AS HE WAS CLEANING, HIS LEFT MIDDLE FINGER WAS CUT BY THE METAL. HE WRAPPED HIS FINGER WITH A RAG AND SOME TAPE AND CONTINUED TO WORK. HIS SUPERVISOR WENT TO CHECK ON HIM ABOUT 1630 AND NOTICED THE BLOOD ON HIS HAND AND ASKED WHAT HE HAD DONE. HE EXPLAINED AND WENT HOME. WHEN HE GOT THERE HE NOTICED HIS FINGER WAS STILL

EE WAS CLIMBING OUT OF A FEEDER BREAKER WHEN HIS KNEE GAVE AWAY CAUSING PAIN IN THE BACK OF HIS KNEE.

AT THE END OF THE WORK SHIFT EE BEGAN TO CLEAN THE DIRT & SWEAT OFF OF HIS FACE WITH A RAG HE HAD PICKED UP IN THE RAG BOX. THERE MUST HAVE BEENSOMETHING ON THE RAG BECAUSE HE SCRATCHED HIS LE FT EYE. THE NEXT DAY HIS EYE WAS IRRITATED & HE WENT TO THE E.R. & GOT MEDICINE FOR HIS EYE.

AS EE WAS WASHING A PHILLIPS BEAKER LIP CRACKED AND CUT TOP OF RIGHT INDEX FINGER AT TIME OF OCCURRENCE SHE WAS WEARING A LATEX GLOVE. EE RMSED CUT WITH WATER, DRIED WITH PAPER TOWEL AND SUPER VISOR APPLIED TWO BANDAIDS.

EE WAS WASHING DOWN THE DRAIN/SIDEWALK ON THE SLOUTH SIDE OF THE MILL BUILDING. BUILDUP WAS HEAVY AND NEEDED LOTS OF WATER. EE WAS GOING TO SET THE HOSE ON THE GROUND AND LET IT FLOW. AS HE BE NT OVER HE FELT A "POP" IN HIS LOWER BACK. HE COULD NOT BEND OVER. WAS TAKEN TO AVMC WHERE HE WAS SEEN BY DR. LIGHT DUTY

EE WAS HELPING START EQUIPMENT FOR THE MINE OPERATION. HE HAD STARTED UNIT AND AS HE WAS EXITING THE CAB HE HAD HIS RIGHT HAND ON THE HOOD HANDRAIL AND STEPPING DOWN FROM FENDER ONTO THE TRACK S. THE TRACKS HAD SOME ICE BUILDUP FROM THE RAIN THE NIGHT BEFORE. WHEN EE STEPPED ONTO THE TRACKS HIS FEET SLIPPED AND HE FELL. AS HE WAS FALLING HE TRIED TO CATCH HIMSELF BY PUTTING HIS HAN

E IN THE PROCESS OF CLEANING OUT A 55 GAL OF USED GRINDING BALLS AT THE SAG MILL. AS HE WAS PULLING ON THE DRUM TAG LINE TO MOVE THE BALLS(THE DRUM WAS SUSPENDED BY AN OVERHEAD CRANE), HE FELT A POP IN HIS LEFT FOOT FOLLOWED BY PAIN. TAKEN TO ER WHERE X-RAYS WERE TAKEN. X-RAYS CONFIRMED A BREAK HAD OCCRRED IN METATARSAL BONE IN HIS LEFT FOOT. FITTED W/WALKING CAST & RESTRICTED DUTY

EE WAS INJURED WHEN A SLIVER OF METAL RICOCHETED OFF OF THE BUSHING HE WAS REMOVING AND STRUCK YHIM IN THE LEFT CHEEK.

EE HAD TOLD HIS SUPERVISOR THAT HE WAS HAVING PAIN IN HIS CHEST AND RIGHT SHOULDER, AND HAD TINGLING SENSSATION IN BOTH OF HIS HANDS AND FINGERS. EE ALSO TOLD HIM THAT HE HAD BEEN EXPERIENCING THE TINGLING IN HIS FINGERS FOR TWO DAYS. HE TOOK HIM THE THE ER TO BE CHECKED. HE TOLD THE DT THAT HE HAD 5 BROTHERS THAT HAVE HAD HEART DISEASE. ER DR TO EE THAT HE WAS GOING TO ADMIT HIM

EE AND COWRKER WERE WORKING ON THE D50K DRILLINSTALLING THE MAST RAISE CYLINDERS. EE HAD WELDED TWO PIN BOSSES IN PLACE FOR THE LET LOWER CYLINDER PINHOLE. WHEN THEY TRIED TO INSTALL THE CYLIN DER THEY REALIZED THAT ONE OF THE WELDED BOSSES WAS NOT IN ALIGNMENT. EE STARTED TO CUT IT OFF THE A TORCH TO REPOSITION THE BOSS. WHILE EE WAS CUTTING, THE TORCH CAME ACROSS SOME GREASE, WHI

AS A RESULT OF OUR AUDIO TESTING PROGRAM SF PHOSPHATES LIMITED CO HAS RECEIVED INFORMATION FROM THE CO PERFORMING AUDIO TESTING AND COMPARING THE MOST RECENT HEARING TEST RESULTS TO BASELINE T ESTS THAT EE SHOWS A CHANGE IN HEARING LEVEL, A STANDARD THRESHOLD SHIFT. WE ARE NOT SURE IF THIS LOSS IS A RESULT OF EXPOSURE TO NOISE ON OR OFF THE JOB. HEARING PROTECTION IS REQUIRED AND U

EE STEPPED ON AROCK WHILE GETTING OUT OF BACK OF SERICE TRUCK FELL INTO TRACK OF D11

PUSHING A BARREL OF GRINDING BALLS ON A CRANE AND FELT PAIN IN LOWER BACK.

AS EMPLOYEE WAS DESCENDING THE ACCESS LADDER OF A CATEPILLAR 824 C RUBBER TIRE DOZER HIS RIGHT KNEE GAVE WAY. EMPLOYEE WAS IN THE PROCESS OF FUELING THE MINE EQUIPMENT.

EE WAS OPERATING FRONT END LOADER AT THE ORE FACE LOADING TRUCKS. HE WENT INTO THE FACE GOT A BUCKET, THE FRONT OF THE BUCKET HIT SOME HARD TOE, CAUSING THE LOADER TO STOP AND THE REAR END BOU NCED, CAUSING EE TO HIT THE TOP OF THE CAB WITH HIS HEAD. EE STARTED THAT HE WAS USING THE SEAT BELT AT THE TIME OF THE ACCIDENT.

EE WAS TIGHTENING BOLTS OF THE CORNER BITS OF A DOZER. A SPECK OF DIRT GOT IN HIS RIGHT EYE. EE WAS WEARING SAFETY GLASSS W/O SIDE SHIELDS. HE RUBBED HIS EYE & THOUGHT HE GOT IT OUT. CONTINUED TO WORK. AT HOME IT STARTED TO BOTHER HIM AGAIN, SO HE RINSED HIS, FELT BETTER. NEXT MORNING STILL HURTING. CAME TO WORK. TOLD SUPERVISOR WENT TO DR. SPECK REMOVE. RTN TO WORK. LATER WENT HOM

EE WAS CHANGING THE PISTON FLUSH LINE ON THE #8 MAINLINE PUMP. THE WRENCH HE WAS USING TO UNDO THE FITTING BOLT SLIPPED OFF THE BOLT & THE END OF THE WRENCH HIT EE IN THE MOUTH

EE WAS WORKING ON THE FEEDER BREAKER. HE WAS ON THE FEEDER BREAKER CONTROL PANEL ATTEMPTING TO CONNECT THE MAIN POWER BREAKER LEVER. WHEN HE STEPPED DOWN OFF THE CONTROL PANEL, HE STEPPED ON W HAT LOOKED LIKE DIR, BUT UNDER THE DIR WAS ICE AND HIS FEET WENT OUT FROM UNDERNEATH HIM.

EMP WAS LOADING HAY BALES INTO A PICKUP TRUCK TO FEED ELK. TOP BALES WERE FROZEN DOWN. WHEN EMP WAS PULLING ON THE TOP BALE STRINGS THE STRINGS BROKE. THIS ALLOWED EMP TO FALL BACKWARDS. MEDIC AL EVALUATION 2-28-97.

WHILE CHANGING A RIPPER SHANK GUARD EE WAS HOLDING A BOLT WITH A PAIR OF PLIERS [FOR A DRIFT PUNCH]. WHEN ANOTHER EE STRUCK THE BOLT WITH A HAMMER THE BOLT FLEW UP & STRUCK EE IN THE FACE. NOT E: NO MEDICAL TREATMENT UNTIL 11/7/96.

ATENDONITIS FROM HAMMERING IN FEEDER BREAKER - SEE ATTACHED. DR. VISIT ON 10/31/96.

EMPLOYEE WAS MOUNTING A SPARE TIRE ON A RIM FOR A CAT 777 HAUL TRUKC. HE WAS PUTTING THE BEAD RING ON THE TIRE TO INSTALL IT WHEN IT SLIPPED OFF THE TIRE, STRIKING HIM ACROSS THE TOP OF THE LE FT FOOT.

EE WAS CLIMBING UP ON THE 12" PUMP DISCHARGE LINE. HIS FOOT SLIPPED OFF THE PIPE AND HE BUMPED HIS ELBOW ON THE CORNER OF THE MOTOR BASE.

WHILE TIGHTENING BOLTS ON THE FEEDER BREAKER A 1 7/8" END WRENCH SLIPPED OFF OF A BOLT AND THE WRENCH HIT EMP IN THE MOUTH. EMP SUFFERED A BROKEN TOOTH.

EMPLOYEE WAS PULLING A TOUPHING ROLLER FRAME FROM UNDER A CONVEYOR BELT WHENHE TRIPPED OVER A ROCK THAT WAS ON THE GROUND & FELL BACKWARDS THE LEFT SIDE OF HIS RIB CAPE HIT A TROUGHING ROLLER FRAME THAT WAS ON THE GROUND

REMOVING BLOCKING FROM UNDER A SCRABER. WHEN EE PULLED ON THE BLOCKS ONE OF THE BLOCKS BOUND UP AND STOPPED EE FELT HIS BACK POP.

ON WED 2-22-95 EMPLOYEE WAS GRINDING ON METAL INTHE SHOP. ON FRI 2-24-95 HE BEGAN TO EXPERIENCE IRRITATION IN HIS LEFT EYE. HE DECIDED TO GO TO THE DOCTOR TO INVESTIGATE THE CAUSE. THE DR. DISCOVERED WHERE THERE HAD BEEN TWO SMALL METAL FRAGMENTS IN HIS EYE. THE DR. REMOVED RUST PARTICLES AND TREATED THE EYE.

EMPLOYEE WAS USING A 4" DISK GRINDER TO PREPARE A METAL SURFACE TO BE WELDED. METAL FILINGS ACCUMULATED ON THE HEAD BAND OF THE FACE SHIELD. WHEN HE FLIPPED UP THE SHIELD WHEN DONE GRINDING, T HE ACCUMULATED FILINGS FELL DOWN OFF THE HARD HAT & SOME GOT INTO HIS EYE. ONE 01/13/95 DR. ISSUED PRESCRIPTION FOR ANTIBIOTIC AS A PREVENTIVE MEASURE.

MINE INSTALLING A PIECE OF PLATE STEEL IN THE TRNASFER CHUTE FOR THE BELTS. MECHINC WAS STANDING ON WHILE ANOTHER EE WAS UNDER HOLDING THE PLATE AND WAITING FOR THE MECHANIC TO TACK WELD IT IN TO PLACE. THE WELDING MACHINE WOULD NOT OPERATE PROPERLY MECHANIC LEFT THE BELT AND WENT TO INVESTIGATE THE PROBLEM. FOUND THE THROTTLE SPRING ONT HE WELDER SERVICE TRUCK HAD CAME OFF.

EMPLOYEE WAS HELPIGN ANTOHER EMPLOYEE LOWER A CONVEYOR ROLLER FRAME TO THE GROUND. INJURED EMPLOYEE TURNE DIMPROPERTY AND IN DOING SO STRAINED THE RIGHT SIDE OF HIS LOWER BACK. ROLLER FRAME W EIGHT IS APPROX 50 POUNDS.

EMPLOYEE WAS HELPING REPLACE SHEAR PIN BUSHINGS IN A FEEDER BRAKER SPROCKET. EMPLOYEE WAS HOLDING A SLEDGE HAMMER ON A BUSHING TO BE POUNDED OUT. ANOTHER EMPLOYEE KENT KELLER WAS POUNDING ON THIS HAMMER WITH ANOTHER HAMMER WHEN A SMALL PIECE OF METAL FLEW OFF AND STRUCK EMPLOYEE IN THE NECK BELOW THE CHIN.

EMPLOYEE WAS ATTEMPTING TO LFIT A BELT LOAD LEVELER SO A LARGE ROCK COULD BE REMOVED FROM BEELT. WHEN LEVELER WAS LIFTTED, THE ROCK SHIFTED AND PINNED EMPLOYEES LEFT LITTLE FINGER BETWEEN ROC K AND LEVELER.

EMPLOYEE WAS USING A RAZOR KNIFE TO TRIM PVC BACKED. FOAM INSUALTION. HE WAS KNEELING DOWN AN D CUTTING TO THE SIDE OF HIS RIGHT LEG. THE KNIFE SLIPPED AND HE DREW IN INTO THIS RIGHT ELG A BOUT 4" INCHES ABOVE HIS KNEE.

EMPLOYEE HAD REPLACED A FAULTY 12 WATER GALVE & JUST FINISHED TRIGHTENING THE LAST BOLT AS HE STEPPED DOWN HE STEPPED ON TO A PIECE OF 11/2 PIPE CAUSING HIM TO TURN ANKLE