Buscar en el registro

When rotating the classifier wheel pinched his finger between wheel and an obscure lip on the classifier body behind the wheel.

While employee was working on mill, he pinched palm of his left hand causing a laceration which required sutures.

While employee was installing shims in the ACM Mill classifier wheel he cut his thumb on one of the shims.

While employee was putting supplies away his hand brushed across the sharp edge of a bracket causing a gash to back side of left hand.

Employee states that while he was working on the tail pulley bearing on elevator 015 he went to turn around and ran his knee into a piece of steel jutting out.

EE STATES THAT HE WAS CHANGING THE AIRLOCKS ON LINE 2 (PLT. 2). WHEN HE LIFTED AIRLOCK HE HURT HIS BACK.

EE WAS CHANGING SEAT AND FLOP GATE ON VAC., VALVE ACTIVATED AIR PISTON AND END OF FINGER ON RT. HAND GOT CAUGHT.

EMPLOYEE STATES THAT WHILE BRUSHING SCREENS HE FELT A SPASM IN HIS LOWER BACK. STATES THAT HE STOPPED UNTIL SPASM WENT AWAY. HE STARTED BRUSH-ING SCREENS AGAIN AND THE SPASM CAME BACK. THIS TIME IT DIDN'T STOP.

WHILE TWO OTHER EMPLOYEES WERE PULLING EE OUT OF #1 PEBBLE MILL (ONE ON EACH ARM), THE MAN ON HIS LEFT ARM PULLED TOO HARD.

WHILE EMPLOYEE WAS DUMPING 99 LB. BAGS OUT BACK, HSI SHOULDER PULLED OUT.

WHILE EE WAS WORKING ON #2 PEBBLE MILL--NEW FEED SPOUT--DUST WAS FALLING AND GOT INTO HIS EYES.

WHILE EE WAS CHECKING AN AIRLOCK THE TIP OF HIS MIDDLE FINGER, LEFT HAND, GOT CAUGHT BY THE AIRLOCK 211A AND WAS CUT OFF.

EMPLOYEE STATES THAT WHEN PULLING ON BAG LOPS HIS BACK CAUGHT.

WHEN EMPLOYEE WAS PULLING AN EMPTY BAG ON BAGGER HE REACHED OVER AND PULLED HIS BACK.

WHILE EMPLOYEE WAS GETTING OFF THE FORKLIFT HE CAUGHT HIS FOOT UNDER THE GAS PEDAL CAUSING HIM TO TWIST HIS RIGHT KNEE.

EE WAS HELPING ANOTHER EE PICK UP A 20' PIECE OF HEAVY WALL PIPE(USING THE PROPER LIFTING TECHNIQUE) BUT TWISTED ONE THE PIPE WAS IN A RAISED POSITION CAUSING LOW BACK MUSCLE STRAIN. EE DID NO T BEGIN LOSING TIME UNTIL 5/29/98.

EMP STATES THAT WHILE HE WAS WASHING A GLASS BEAKER THAT HAD A CHIP ON THE TOP WHICH HE DID NOT DETECT BEFORE WASHING IT HE CUT THE PALM OF LEFTHAND WHICH REQUIRED STITCHES.

EE WAS ATTEMPTING TO CALIBRATE A BULK SCALE. HE & ANOTHER EE WERE USING A FORK LIFT TO PUT A 2000 LB. TEST WEIGHT ON SCALE. HE PUSHED ON WEIGHT.

EMPLOYEE STATES THAT HE WAS SHOVELING AND SWEEPING GARNET AND ROCK WASTE WHEN HE FELT A SUDDEN PAIN IN HIS RIGHT LOWER BACK, RIGHT SHOULDER AND ELBOW.

EE STATES THAT WHILE HE WAS CLEANING UP AROUND BAGGER PICKING UP OLD PALLETS 70LBS AND CARDBOARD HE FELT SEVERE PAIN IN HIS LOWER LUMBAR AREA.

WHLE EMPLOYEE WAS UNLOADING BARRELS OF 200 & C101 OFF DOCK INTO LOADER BUCKET, A BARREL DROPPED AND LANDED ON HIS RIGHT FOOT.

WHILE EE WAS UNPLUGGING FEED CHUTE ON #1 PEBBLE MILLE HE STATES THAT HIS HAND SLIPPED AND SCRAPED A SHARP PIECE OF METAL (ANGLE IRON).

WHEN EMPLOYEE BENT DOWN TO PICK UP A SAMPLE KNIFE THAT HE DROPPED ON THE FLOOR HE PULLED HIS BACK.

WHILE EMPLOYEE WAS WORKING ON PEBBLE MILL A MAN INSIDE MILL HOLLERED TO HIM TO HAND HIM A BOX OF TILE WHEN EMPLOYEE TURNED HE RAN HIS HEAD INTO BOLT

EMPLOYEE WAS MOVING TRUCK TIRES AROUND ON THE STOCKPILE WHEN HE FELT PAIN IN HIS BACK.

EMPLOYEE PULLED BACK WHEN LIFTING ON AUGER OF SCREW 54.

EE TRIED TO MOVE A GAYLORD BOX BY HAND & PULLED A MUSCLE IN HIS BACK.

EMPLOYEE WAS CHANGING PLATES IN F-1 MILL HE CUT HIS INDEX FINGER IN LIP OF HEAD. EDGE OF HEAD IS SHARP. EMPLOYEE RECEIVED 4 STITCHES.

WHILE EE WAS TRYING TO INSTALL SLIDE TO WORK ON FEEDER HIS HAND SLID ACROSS SLIDE TEARING HIS LEFT PALM OPEN. SLIDE HAS BEEN HAMMERED ON SO MUCH THAT THE FLAT EDGE HAS BECOME RAZOR SHARP. EE R ECEIVED 4 STITCHES.

EMPLOYEE WAS ROLLING A BARREL OF SCREEN OVERSIZE ONTO A PALLET WHEN HIS BACK GAVE WAY. EMPLOYEE WAS UNABLE TO STRAIGHTEN UP.

EMPLOYEE WAS SHOVELING UNDER CONVEYORS WHEN HE PULLED MUSCLE IN BACK.

WHEN EMPLOYEE BENT DOWN TO PICK UP AN EMPTY PALLET HE PULLED A MUSCLE IN HIS BACK.

WAS CLEANING MAGNETS ON EXOLONS AND PERMROLLS. WHILE REMOVING MAGNET FROM 23 PERMROLL HE FELT A TWINGE IN HIS BACK. BY THE TIME HE WASLKED TO THE LAB MUSCLE HAD TIGHTENED UP.

WHILE THROWING BAGS BACK THROUGH A BAG FLATTENER, EMPLOYEE FELT A TWINGE IN HIS BACK.

WHILE INSTALLING A TWO INCH VALVE, EE DROPPED THE VALVE WHILE HE WAS TRYING TO CATCH IT THE VALVE STRUCK HIM IN THE RIGHT HAND INJURING THE 3RD JOINT IN THE LITTLE FINGER.

WHILE CHECKING LIGHTS THE EMPLOYEE REACHED UNDER A BEAM PUTTING HIMSELF IN AN AWKWARD POSITION AND HE PULLED A MUSCLE IN HIS LOWER BACK.

EMPLOYEE THINKS THAT HE HURT HIMSELF LIFTING SOME STEEL INSIDE A BUILDING WHILE HE WAS CLEANING THE AREA.

FILLING BAG WITH PORDUCT DUST FELL IN EYE

LOADING PALLET WALKED BY SCRATCHED ANKLE ON PC OF STRAPPING STICK ING OUT

EMPLOYEE WAS MOVING A STEEL PLATE AND DROPPED IT ON HIS FOOT.EMPLOYEE WAS WEARING STEEL TOED WORK BOOTS AT THE TIME OF INJURY.

EMPLOYEE WAS INJECTING A LIQUID CHEMICAL INTO A TANK. THE QUICK DISCONNECT PULLED APART AND CHEMICAL SPLASHED OUT OF THE TANK ONTO EMPLOYEE.

54736YEE WAS SHIFTING GRATING AROUND ON THE STEEL & TRIED TO MOVE A PIECE WITH HIS BODY

EMPLOYEE WAS SHOVELING PRODUCT MOST OF WEEK AND HE COULD NOT GET OUT OF BED ON 02-22-92.

WHILE LIFTING AN EXOLEN ROTOR HE STRAINED HIS BACK.

CHECKING CYLINDER ON BAGGER FINGER PINCHED

WHILE EMPLOYEE WAS SHOVELING CRUSHED ORE HE FELT A TWINGE IN HIS LOWER BACK.

EMPLOYEE WAS DUMPING BAGS OF PRODUCT INTO AN ELEVATOR AND HE PULLED A MUSCLE IN HIS SHOULDER.

WHILE OPENING A MIXER DOOR, EMPLOYEE FELT A PULL IN HIS SHOULDER AND ARM.

EE WAS SLIDING A COVER OVER THE TOP OF 6 MILL ELEVATOR AND PULLED A MUSCLE IN HIS BACK.

EMPLOYEE WAS LIFTING A BAG OF GARNET AND FELT SOMETHING GIVE IN HIS RIGHT TESTICLE.