Buscar en el registro

Removing a fan from a track unit and the wrench slipped, resulting in a cut to the palm of employee's right hand, near thumb area. Employee received five (5) stitches.

Employee was tightening upper bolts on breaker plates using a 3/4" ratchet in a tight area. The ratchet slipped out of the socket and with the force trying to tighten it, smashed his right hand pinky finger.

Employee was using a utility knife to cut open the center strip of rubber on the 8 x 20 screen. Knife slipped and cut his left palm of hand.

Employee was cutting conveyor belting from a roll to use as a chute deflector. The knife did not cut all the way through, so the employee made a cut by pulling the knife toward him. The knife slipped and cut him in the left knee.

While employee was using a 16 lb. sledge hammer he felt a strain in his lower back. The employee has been trained in the proper handling of a sledge hammer to avoid future injuries.

Employee was doing maintenance work on his loader. He was using a sledgehammer to drive a pin out of a loader tooth. The sledgehammer glanced off the corner of the punch and struck the left hand index finger.

EMPLOYEE WAS USING A PORTA-POWER RAN TO STRAIGHTEN A BENT BRACKET ON A CONVEYOR. THE PISTON/RAM CAME OUT AND LANDED ON HIS LEFT INDEX FINGER. HIS FINGER WAS PUSHED INTO AN ANGLE IRON CAUSING A LACERATION.

EE WAS USING A #20 SLEDGE HAMMER AND FELT PAIN AFTER REPEATED USE.

MECHANIC WAS REMOVING A UNIVERSAL JOINT FROM A DRIVE SHAFT, WITH THE SHAFT CLAMPED IN A VISE HE WAS HAMMERING ONT HE CROSS OF THE JOINT WHEN A PIECE FRAGMENTED FROM THE HAMMER AND IT LODGED IN HIS LEFT FOREARM.

WHILE ATTEMPTING TO PULL A SPLICED PIECE OF HOSEAPART, HE FAILED TO PUT DOWN A RAZOR KNIFE THAT HE WAS HOLDING IN HIS RIGHT HAND. AS HE WAS PULLING ON THE HOSE, THE KNIFE CUT HIS KNUCKLE OF "L ITTLE" FINGER ON HIS LEFT HAND CAUSING A LACERATION.

WHILE TAKING A BOLT OUT OF THE LOADER, THE WRENCH SLIPPED AND CAUSED HIS HAND TO STRIKE THE ENGINE BLOCK WITH HIS FINGER AND CAUSED A SMALL LACERATION THAT REQUIRED 3 SUTURES.

LACERATION TO LEG. EE LACERATED LEG WHILE CUTTING A CONVEYOR BELT WHILE USING A UTILITY KNIFE.

WHILE SITTING DOWN WITH BOTH LEGS HANGING OVER EDGE OF CONE CHASSIS, HE WAS USING 2 WRENCHES TO TIGHTEN LUBRICATION FITTINGS. WHEN HE PULLED WRENCHES TOGETHER HE FELT A POP IN HIS LEFT TERS TICLE Y

EE STATES WHILE SWEEPING THE FLOOR OF THE ELECTRICAL TRAILER FINE PARTICLES OF ROCK DUST ENTEREDHIS EYES FOREIGN MATTERS IRRITATED HIS CONTACT LENSES

WAS USING A SLEDGE HAMMER TO REMOVE AN ANVIL FROM THE VSI. A PIECE OF THE ANVIL BROKE OFF AND HIT EE IN NOSE.

HE WAS REPLACING THE LINERS IN THE DISCHARGE CHUTE OF THE CRUSHER. HE WAS PRYING THE LINER TO LINE UP THE BOLT HOLES, WHEN THE PRY BAR SLIPPED.

HE WAS USING A PORT-A-POWER TO FIT A PIECE OF METAL WHEN IT SLIPPED & CAUGHT HIS LEFT INDEX FINGER

HE WAS DIGGING AREA OUT AROUND THE CONE TO MOVE CONVEYOR. THE PRY BAR HE WAS USING SLIPPED ONT HE FROZEN MATERIAL SMASHING HIS FINGER BETWEEN THE BAR AND THE ANGLE IRON.

HE WAS WORKING ON HEAD PULLEY OF CONVEYOR WHEN BAR HE WAS USING SLIPPED CASUING HIM TO FALL TO GROUND LANDING AGAINST WHEEL OF CONVEYOR.

CUTTING CORKBOARD FOR INSPECTORS TRAILER,KNIFE SLIPPED & CUT UPPER THIGH.

EMPL PUTTING TOOTH IN BUCKET OF LOADER HAMMERING IT IN PLACE.PIECE OF METAL STRUCK HIM ABOVE RIGHT EYE.

EMPLOYEE WAS BA9RING A ROCK IN SCRUSHER HOPPER, A FLYING ROCK HIT BACK OF EAR, CAUSING A LACERATION, WHICH REQUIRED SUTURES.

EMPLOYEE WAS CUTTING MATERIAL WITH KNIFE, THE KNIFE SLIPPED, LACERATING LEFT HAND, REQUIRED 2 SUTURES