Buscar en el registro

Emp using a sledge to straighten track, sliver from sledge came back and cut employee's face.

Employee was slicing conveyor belt and cut their hand with a knife. Stitches

Changing bucket teeth on a Caterpillar 374 excavator. Using a sledgehammer to remove the teeth, a 7mm chunk of tooth broke off and entered the operators left leg just above the knee.

Trying to pry a pulley off, bar slipped and caught their thumb between the two.

Crusher was plugged and we were try unplugging it and I was on the crusher floor stabbing the side of the crusher with a pry bar to knock the rock down and while doing it my right wrist popped. I now have a sharp pain in my wrist, hard to lift anything and rotate. I did not stash it and it is not swollen just hurts when I move it

Prying a rock out and cutting EE's finger and got stitches

Injured employee was scaling built up material off the side of feed hopper with a bar when they caught the end of their left pinky finger between the bar and hopper wall resulting in a closed fracture to the tip of the finger.

Employee was swinging a sledgehammer and felt a pop in shoulder

The injured employee was unclogging an infeed hopper when the chute gate IE was holding was contacted by a chunk of clay. IE's right ring finger was caught between the chute gate and the chunk of clay resulting in a laceration. The injured employee was escorted for further medical treatment that resulted in 11 sutures.

Employee operating the unit, was struck with a come-a-long on their right hand due to being in the line of fire.

Employee cut leg with a knife and received stitches.

Employee was trying to remove the lock pin on the #4 crusher with a pry bar and dropped the bowl on their middle finger.

Employee was working on the stuck clamshell and employee's hand and tool slipped causing the clamshell to come down on the back of the hand. Employee received stitches.

Employee was cutting a belt with a knife and it slipped, cutting left pinky finger. Employee received 10 stitches.

Employee was loosening a bolt when EE cut EE's finger on the threads. EE received 6 stitches and EE went back to work.

Employee was trying to remove a tooth from a loader bucket with a hammer and part of the tooth chipped and entered EE's abdomen.

Employee was using a hammer when it bounced back and hit EE in the eyelid.

Employee was using a breaker wrench and it snapped off and struck underneath employee's PPE and cut employee's cheek.

Employee was using a pry bar to open gates at the primary scalping screen when the bar slipped and smashed the right middle finger between the pry bar and the screening unit.

Employee was using employee's pocket knife to cut a zip tie and cut in between index and thumb, requiring 1 stitch.

Employee was getting a drill core out of the tube and struck finger with a mallet. Employee received 2 stitches.

Employee was swinging a sledge hammer when employee felt a pain in employee's back. Employee finished employee's day and when employee came back to work today, employee wanted to go to the clinic.

Employee was using a hammer to break up rock in the grizzly bars and a rock came back and struck safety glasses, and injured eye.

Employee was swinging a hammer and hurt back. The initial reporting of the injury was employee stood up and took a deep breath and back hurt. This injury was found compensable 9/9/2016.

Employee was using a pick ax to break up buildup under a conveyor and strained his hand. He did not report the injury until 12/16/15 and requested medical attention.

Employee was installing a motor when the wrench he was using slipped causing him to lose his balance and fall backwards hitting his head. He also complained of chest and back pain.

Employee was turning a wrench, it slipped, causing his left hand to hit the crusher frame. He did not seek treatment until 12/31/2014 and presented with a fracture.

Employee was adjusting the packing on the pump when the wrench slipped and struck his finger.

Employee smashed his finger between a sledge hammer and a table, fracturing it.

While tightening a fitting on a scrubber, the employee pulled a muscle in his upper back.

Employee was using a self retracting safety knife to cut skirting when the safety feature failed and he cut his inner thigh. Stitches required.

Employee was hammering in a wedge on the screen when he smashed his thumb with the hammer.

Employee was breaking bolts loose on the pipeline and pulled a muscle in his back.

Was working with another employee on a conveyor when the other employee turned towards him with a cutting tool in hand and cut his left arm, requiring stitches.

Employee was using a prybar to lift roller for repair when the pry bar slipped causing the employee to fall.

Employee was wrenching on a bolt when he felt something pop in his left elbow.

Employee was changing out the parking brake on a loader when the wrench slipped. the U-joint broke and cut his hand.

Hammering in a bearing on a loader when the hammer glanced off the bearing causing the arm strain.

Employee was using a hoist/come-a-long to help place a sprocket on a shaft. The hoist became dislodged catching his finger in between the sprocket and the shaft.

Was shoveling and shovel abruptly stopped and dislocated his shoulder.

Employee was loosening pipe using wrench. Wrench slipped and his finger was caught between wrench and pipe.

EE was using a come-a-long to clean up under the 7x30 and pulled something in his back.

EE was cutting side skirts for 7x30, he got up to get something then went to get back down and cut his leg with his knife on the leg, above the knee.

EE was using a wrench and cheater pipe on a transmission bolt. The wrench slipped and struck him in the face/mouth/teeth.

EE was using a pry bar to dislodge clay and rock from crusher slide. The material broke off, and caused the pry bar to kick up and hit him in the face.

Injury was using a hammer wrench. A nut came loose and he smashed his finger between the wrench and a speed reducer.

EE was trying to open back door on skid-steer loader. He used a file to pry it open. The file broke and cut his left arm.

Injury strained his back using a shovel to pry a block of ice out of a haul truck.

Injured was using a sledge hammer to close a bin gate. His finger was smashed between the hammer and a metal beam.

Employee was using a wrench to replace a hoist cylinder on a Caterpillar 980F loader. The wrench slipped, smashing finger between cylinder and wrench.