Buscar en el registro

Injured was helping replace return roller on conveyor using a come-along when hook slipped and hit employee in face/eye causing an abrasion to eye.

Employee was using digging bar where rock was lodged in chute at Primary plant. Rock dislodged, hit digging bar and smashed employee's left pinky finger. Employee has to wear finger splint until cleared by Doctor.

Employee was performing maintenance on #2 screen. Using a pry bar on counter weight when bar slipped. Felt the right shoulder pop. Employee is the superintendent for the welding team. At the time of the accident they had no lost time or restrictions. Later MRI was done and found a torn rotator cuff. Surgery on November 28, 2018.

Employee was changing out motor on #1 Conveyor. EE was using a pry bar to help lift motor when bar slipped letting motor fall on tip of finger causing fingernail to pop off and cutting tip of finger.

Employee was putting teeth on a 988 Cat Loader. He was using a hammer to knock pin clips in when he hit the tooth with hammer causing a piece of metal to chip off and enter employee's upper leg. As of now its still not decided if they will remove or leave metal in.

Employee was standing on crusher platform using a digging bar to try and dislodge a wedged rock in jaw crusher feeder when bar slipped catching his finger between the bar and handrail. This caused a laceration to tip of ring finger on right hand requiring 8 stitches.

Employee was using a utility knife to cut belt for skirtboard when knife slipped causing a laceration to his left pinky finger that required 4 stitches.

Employee was working on conveyor, he was using a hammer to put a bolt throught a turnbuckle when he missed bolt and hit his left thumb causing a laceration requiring sutures.

Employee and a co-worker was using hammer to clean out a box at old pugmill, co-worker went to hit box, hammer glanced off angle iron, came back and hit employee in eye with hammer. Safety glasses broke and cut employee above eye, requiring stitches.

Employee was using a pocket knife, to cut tape that was holding stirring paddle, off a bucket of backing. The knife slipped, causing a laceration to his left thumb.

Employee was using a hammer to tighten cheek plates in jaw, when eye that was holding cheek plate broke off, striking employee in lower right arm, causing a bruise.

Employee was taking cheek plates out of jaw using a hammer and wedges, wedge slipped and either wedge or cheek plate mashed his finger

Employee was using a sledge hammer to put side rail on screen; went to hit side rail, handle of hammer caught causing him to miss the intended target and strik his right index finger.

EE WAS HOLDING A BAR ON A SPACER ON A CENTER PIN IN A 980 LOADER WHILE ANOTHER EE WAS TAPPING ON THE BAR TO DETERMINE HOW TIGHT THE SPACER WAS WHEN A CHIP OF METAL FLEW OFF THE SPACER AND WENT IN EMLOYEE'S LEFT ARM JUST ABOVE THE WRIST. WAS INSTRUCTED NOT TO USE ARM FOR 2 DAYS. DECIDED TO LEAVE METAL IN, MAY HAVE TO TAKE IT OUT LATER DATE IF IT FLARES UP.

EMPLOYEE WAS UNDER DUMP TRUCK ADJUSTING CLUTCH WHEN DIRT AND METAL SHAVINGS FELL IN AROUND EMPLOYEE'S SAFETY GLASSES INTO EYES. EMPLOYEE WENT TO DOCTOR WHERE 3 SMALL PIECES OF METAL WERE REMOVED FROM EYE.

PLANT DOWN DOING MAINTENANCE AND CLEANUP. EE WAS AT JAW CRUSHER DOING CLEANUP ON THE JAW CRUSHER PLATFORM. HE WAS SITTING DOWN HITTING ROCKS WITH A HAMMER TO KNOCK THEM THRU THE PLATFORM. EE S TATES HE FELL THROUGH THE HANDRAIL, HANDRAIL HASA MID RAIL. EE FELL APPROX. 15'. HE HAS A CUT TO LEFT HAND WHICH NEEDED STITCHES, CUT ON BACK OF HEAD AND BROKEN RIBS.

INJURY OCCURRED WHEN INJURED WAS REMOVING BAIL ON DRILL HAMMER USING A WRENCH SPECIFICALLY DESIGNED FOR THIS PURPOSE AND A 2# HAMMER HANDLE BECAUSE HE WAS HAVING TROUBLE GETTING BAIL TO MOVE. WHOLE DRILL HAMMER TURNED INSTEAD AND BECAUSE IT WAS NOT RESTING ON THE GROUND FELL CATCHING INJURED'S FINGER BETWEEN 2# HAMMER HANDLE AND WRENCH. INJURED IS EXPECTED TO MAKE A FULL RECOVERY.

EE WAS HELPING TO PUT SCREENS IN, EDGES OF SCREEN NEEDED TO BE TRIMMED OFF, WHILE USING A KNIFE TO CUT EDGES OFF, KNIFE SLIPPED AND CUT FINGER.

EE WAS USING A BELT KNIFE TO CUT A SECTION OF BELT FOR SKIRT RUBBER, KNIFE BINDED INTO BELT BEING CUT, EE PULLED WITH FORCE, KNIFE CAME OUT AND STRUCK EE INHIS UPPER LEFT LEG, CAUSING A LACERA TION THAT REQUIRED STITCHES.

EE WAS CLEANING TOP OF PUNCH PLATES ON #1 SHAKER, AS HE HIT ROCK IT BUSTED IN SEVERAL PIECES AND CAME BACK AND HIT EE ON HIS RIGHT LEG AT THE SHIN AREA. EE DID NOT GO TO DR UNTIL 10-31-01.

EE WAS USING A WEDGE TO GET ROCK OUT OF JAW CRUSHER WHEN A PIECE OF METAL CAME OFF WEDGE AND STRUCK HIS CHIN. DID NOT REPORT ACCIDENT UNTIL 10/2MISSING 2 DAYS OF WORK GOING TO DOCTOR.

EMPLOYEE WAS USING A METAL BAR AT JAW CRUSHER TO GET ROCK LOOSE WHEN ROCK SLIPPED, HIT BAR PUSHING HAND INTO HAND RAIL AND CAUSING A CUT AND PINCH TO EMPLOYEE'S RIGHT THUMB. HIS THUMB REQUIRED ONE STICH.

DOING REPAIR WORK ON OUR CASE SKID LOADER. EE WAS USING A BAR TO TRY AND UNLATCH BUCKET, THE BAR SLIPPED AND EE FELL FORWARD STRAINING HIS BACK.

EE WAS TRYING TO GET BEARING OUT OF OLD SHAKER SCREEN (NOT IN USE). EE WAS USING A HAMMER AND CHISEL, HE HIT THE CHISEL WITH HAMMER, THE CHISEL FLEW UP AND STRUCK THE EE IN THE CHIN CAUSING A LACERATION.

EMPLOYEE WAS USING HOOK TO PULL ROCK UP TO PUT WEDGE UNDER TO DISLODGE ROCK IN JAW CRUSHER, WHEN HE FLET PAIN TO HIS LEFT HAND. EMPLOYEE SPRAINED HIS LEFT HAND.

*AMMENDMENT TO REPORT DATED 7/22/99. TAIL PULLEY'S WERE LOCKED DOWN, AND WHILE SHOVELING, DEBRIS GOT INTO EYE CAUSING IRRITATION AND REDNESS. EE WAS WEARING SAFETY GLASSES.

EE WAS USING A WRENCH TO REPLACE A ROLLER ON A CONVEYOR BELT. THE WRENCH SLIPPED OFF AND EE HIT HIS LEFT ELBOW ON AN I BEAM BRUISING HIS ELBOW. THIS EE DID NOT RECEIVE ANY MEDICAL ATTENTION OR HAVE ANY LOST TIME UNTIL HE DECIDED IN MARCH, 2000, THAT HE NEEDED TO GO SEE ABOUT HIS ELBOW, WAS QUESTIONABLE.

EE WAS REMOVING BEARING FROM HOUSING AT FEEDER WHEN HOUSING BROKE FREE SENDING A SLIVER OF METAL FLYING AND EMBEDDING IN GENITALS OF EE CAUSING A SMALL PUNCTURE WOUND. AT THE TIME OF THIS ACCI DENT THIS WAS A NON-REPORTABLE ACCIDENT BUT NOW REPORTABLE DUE TO THE FACT THAT EE HAD SLIVER OF METAL TAKEN OUT WHICH RESULTED IN 3 STITCHES.

EMPLOYEE WAS INSTALLING TRANSMISSION IN R-50 EUCLID TRUCK TIGHTENING BOLTS AND WRENCH SLIPPED OFF AND STRUCK HIM IN THE MOUTH. IT BROKE 1/2 OF TOOTH OFF.

SHOVELING SAND ANDPLANT SAND BLEW OFF BELT AND INTO FACE AND EYES.

CLEANING ROCK OUT FROM UNDER STANDARD CRUSHER WITH PIECE OF DRILL STEEL AND IT SLIPPED OFF ANDD FELL AND HIT HIM IN THE MOUTH.

EMPLOYEE WAS TIGHTENING DOWN NUTS AND BOLTS THAT HOLD THE SHAKER SCREEN. "I WAS PULLING ON THE WRENCH WHEN I FELT A POP/PULLING FEELING IN MY UPPER BACK."

DRIVING BUSHING ON SHAFT OF CRUSHER WITH HAMMER MISSED BUSHING AND HIT THUMB.

EMPLOYEES WERE TRYING TO TAKE HAMMERS OUT OF THECANICA CRUSHER, WHEN THEY HAD TROUBLE THEY USED A DOZER BLADE TO TRY AND BREAK THE HAMMERS LOOSEWHEN A PIECE OF STEEL CHIPPED OFF AND WENT INTO INJURED'S RIGHT ARM.

INJURED WAS CUTTING A CONVEYOR BELT AND HE CUT HIS LEFT KNUCKLE ON HIS INDEX FINGER.

EE WAS CUTTING PC. OF BUCK UP RUBBER FOR SCREEN RAIL, HIS POCKET KNIFE SLIPPED & CUT HIS THUMB ON LEFT HAND.

CHANGING SCREENS AND THE INJURED WAS PULLING ON A WRENCH AND HE STRAINED HIS BACK.

95107UTTING A PLATE ON BACK OF A SCREEN. WAS USING A WRENCH AND THE WRENCH SLIPPED AND EMPL HIT ELBOW ON A PIECE OF METAL. WENT TO SEE DR 7-30-92.

TIGHTENING CHAIN SLIPPED AND INJURED FELL AGAINST A PIECE OF METAL ON THE PLANT.BRUISE TO LEFT ELBOW.

INJURED WAS OBS9RVING FOREMAN AND ANOTHER EMPLOYEE REPAIR TELESMITH CRUSHER WHEN FRAGMENT FROM SLEDGE HAMMER OR CRUSHER STRUCK INJURED IN LEFT EYE

HE WAS SETTING 5 COMEALONG (CHAIN HOIST), AND THE LEVER OR HANDLE FLEW BACK AND STRUCK HIM IN THE MOUTH. IT BROKE HIS TWO TOP FRONT TEETH OUT. NO LOST TIME.

ANOTHYER EMPLOY9E WAS HITTING METAL BAR WITH HAMMER WHEN A PIECE BROKE OFF & HIT EMPLOYEE IN MOUTH CUTTING TONGUE

A LARGE ROCK WA8 IN THE FEEDER AND AS IT PROCEEDED TO THE JAW IT HUNG TO ONE SIDE. GOINES TRIED TO GUIDE THE ROCK AND THE RACK SHIFTED ANDTHEBAR KNOCKED HIS HARD HAT OFF & CUT HIS RIGHT EAR.

EE WAS REPARING TRACKS ON A DOZER A CUTTING TORCH WAS USED TO CUT THE NUT OFF OF A BOLT. EE HIT THE BOLT WITH A HAMMER TO REMOVE IT FROM TE %%* THE HOLE & A PIECE OF SLAG CAME OFF OF THE B OLT STRIKING THE EE ON TE UPPER PART OF T HE CHIN.