Buscar en el registro

EE was holding a pipe onto a small screw shaft, while another EE was hammering the shaft to help remove it, when the pipe slipped off, jamming the EE's right little finger onto the screw housing.

Employee was using a tool to clean out a blockage in the lime feed to the flouride tank when he scraped his right arm, and the lime slurry caused an irritation to that area.

After working to thaw out a come-a-long latch mechanism, EE proceeded to move the ratchet handle in order to crank up loading chute, when the ratchet handle slipped, striking EE on left eye socket area causing a contusion.

EE was tightening belt that holds skirting in place along feed belt that conveys product to plant rodmills. Socket slipped ogg belt causing his right elbow to strike conveyor frame.

While attempting to open the discharge door to the No. 1 Dry Plant's hot tank with a 6-foot pry bar, the employee scrapped his left hand's knuckles on both the little & ring fingers. A deep laceration required staples and physician issued work restrictions.

Injured employee was taking turns with another employee driving the hitch into a trailer's receiver with a 5-lb. hammer. While injured employee was standing behind and to the left of the other employee swinging the hammer, the hammer's wedge flew-out and struck the employee just below the chin causing a laceration that required sutures to close the wound.

EE WAS HELPING LINE A ROD MILL AT THE FELDSPUR OPERATION. EE WAS USING SLEDGE HAMMER KNOCKING OUT BOLTS THAT WAS HOLDING THE OIL LINING IN.EE STARTED TO HIT BOLT, MISSED. EE CAUGHT LEFT THUMB BETWEEN HAMMER HANDLE & BOLT. EE REC'D OPEN FRACTURE OF LEFT THUMB.EE WAS TAKEN TO E.R. WHERE HE REC'D 6 STITCHES & BRACE. LIGHT DUTY

EE WAS MOVING PALLET JACK FROM UNDER PALLET. THE JACK HUNG UP UNDER PALLET AND JERKED EE, PULLING MUSCLE IN LOWER BACK LEFT SIDE. EE WENT TO THE DR. ON 5-3-02 WHERE HE WAS PLACING ON LITE DUTY . IT THEN BECAME REPORTABLE.

EE WAS PLUMBING IN A SINK W/QUEST PIPEING AT THE FILTER PLANT. THE PIPE WAS TOO LONG. EE COULD NOT GET A HACK SAW IN THE SPACE BECAUSE IT WAS A SMALL SPACE. EE TRIED TO CUT THE PIPE W/A POCKET KNIFE. THE KNIFE SLIPPED & CUT LEFT PALM OF HAND JUST BELOW THE THUMB. EE WAS TAKEN TO THE COMPANY DR WHERE HE RECEIVED 6 STITCHES.

LEFT HAND GOT CAUGHT BETWEEN CONEALONG HANDLE AND A PIECE OF METAL. THE COMEALONG WAS ATTACHED TO AND CUT TOP SIDE OF LEFT HAND. WAS TRANSPORTED TO HOSPITAL ER WHERE HE RECEIVED SIX STITCHES I N HAND. THEN IT BECAME REPORTABLE.

PICKED UP SLEDGE HAMMER TO HIT SIDEOF SAND TANK TO LOAD OUT A TRUCK. THE WEATHER WAS VERY COLD AND THE SAND HA DFROZEN. AS THE EMPLOYEE HIT THE SIDE OF THE TANK HE FELT A PULL BETWEEN HIS S HOULDERS ON THE LEFT SIDE. HE AHD PULLED THE MUSCLE JUST UNDER THE LEFT SHOULDER. HE WAS TRANSORTED TO THE DR WHO PLACED EMPLOYEE ON LITE DUTY.

7EMPLOYEE WAS PACKING A PUMP WITH ANOTHER EMPLOYEE. THE INJURED EMLOYEE WAS HOLDING THE PACKING GLAND AS THE SECOND EMPLOYE EWAS PUSHING WITH A BAR. THE BAR SLIPPED AND STRUCK THE INJURED EM PLOYEE ON THE LEFT INDEX FINGER. THE FINGER BECAME INFECTED 3 DAYS LATER.

EMPLOYEE WAS BENDING OVER DRIVING A SCREW OFF OFA SHAFT WITH A 24 OZ. HAMMER. HE STARTED TO RAISE UP AND STRAINED HIS BACK WENT TO DOCTOR ONTHE 17TH OF MAY.

EMPLOYEE WAS WORKING ON PIPELINE WHEN HE STARTEDFEELING PAIN IN HIS CHEST. HE CAME TO THE SHOP AND 911 WAS CALLED TO THE PLANT TO CHECK HIM OUTEMPLOYEE WAS ADMITTED TO HOSPITAL OVERNIGHT FOR TESTS.

EE WAS CUTTING TAPE FROM WIRES ON A MAKE-UP BOX ON A 75 HP MOTOR THE MAKE-UP WIRES WERE RELATIVELY SHORT AND REQUIRED REACHING INTO THE MAKE-UP BOX TO CUT THE TAPE WITH A RAZON KNIFE. HOLDING THE WIRES WITH THE LEFT HAND & CUTTING THE TAPE WITH THE RIGHT THE KNIFE WAS PULLED ACROSS THE TAPE AND ALSO THE RING FINGER OF THE LEFT HAND CAUSING A CUT.

EE WAS CUTTING A PIECE OF RUBBER HOSE. THE KNIFE HE WAS USING SLIPPED STRIKING EE IN LEG CAUSING A WOUND ABOUT 3/4" LONG BY 1" DEEP. THIS WOUND REQUIRED 2 STITCHES.

EE WAS TURNING A FEED SCREW WITH A PIPE WRENCH, WHEN A KNOT POPPED OUT IN THE GROIN AREA. SURGERY WAS REQUIRED ON 10-17-97, AT WHICH TIME THE ACCIDENT WAS REPORTABLE.

EMPLOYEE WAS USING AN ADJUSTABLE WRENCH THAT SLIPPED CAUSING ARM TO STRIKE PANEL BOX, CUTTING ARM.

EMP WAS HELPING LINE A ROD MILL. SAFETY (BACKUP)CHAIN HOIST FELL AND STRUCK HIM IN THE BACK AND SIDE. A BOLT HOLDING THE HOIST BROKE CAUSING IT TO FALL.

EE WAS OPENING A BUCKET AND THE KNIFE HE WAS USING SLIPPED AND CUT HIS ARM. CUT REQUIRED STITCHES.

EMPLOYEE WAS PRYING CHUTE INTO POSTION AND FELT PAIN IN LOWER BACK.

DREW SPIKE HAMMER BACK TO SWING, HEAD FELL OFF HANDLE AND STRUCK EMPLOYEE IN THE SMALL OF BACK CAUSING TRAUMA TO LOWER LUMBAR REGION.

EMPLOYEE WAS DISMANTLING A PUMP AND A WRENCH SLIPPED, STRIKING HIS HAND AGAINST THE PUMP BODY, BREAKING HIS FINGER.

WHILE PUTTING RODS INTO A ROD MILL, THIS EMPLOYEE WAS HIT IN THE EYE BY THE END OF A PUSH ROD (WOODEN) BEING USED BY ANOTHER EMPLOYEE.

EMPLOYEE WAS BREAKING APART ELEVATOR CHAIN WHEN A PIECE OF METAL BROKE OFF AND WENT INTO EMPLOYEES LEFT WRIST.

LOOSENING BOLTS ON MANIFOLD WRENCH SLIPPED HIT L INEX FINGER

EE WAS REACHING DOWN TO HOOK COME A LONG TO PONTOON WHEN BACK POPPED.

EMPLOYEE WAS HOLDING A STEEL PIN WHILE 2ND EMPLOYEE STRUCK IT WITH A SLEDGE HAMMER-2ND EMPLOYEE MISSED THE PIN, STRIKING EMPLOYEE'S RIGHT HAND.

EMPL MOVING MOTOR ON J#1 VACUUM PUMP INTO POSITION WITH PRY BAR AND FELT A KINK IN HIS NECK.

EMPLOYEE WAS GOUGING FROZEN ORE OUT OF A BIN WHEN HE HIT HIS ELBOW OVER THE CHUTE.

CLEANING SCREENS PAIN IN R ELBOW Y

EMPLOYEE WAS CHIPPING SLAG FROM A WELD & A SMALL PIECE FLEW INTO HIS RIGHT EYE

EMPL WAS LOWERING MOTOR & GAR DRIVE INTO POSITION WITH CHAIN HOIST & AS HE WAS ALIGNING BOLT HOLES RIGHT HAND WAS CAUGHT BETWEEN MOTOR & STEEL FRAME. ACTION CAUSED CONTUSION OF EMPLS RIGHT HAN D.

EMPLOYEE WAS USING A WRENCH ON AN ICE COVERED VALVE.THE WRENCH SLIPPED AND HIS FINGER WAS CAUGHT BETWEEN THE WRENCH AND A METAL BOX.

EMPLOYEE WAS PRYING AT ROCK IN CRUSHER. THE ROCK FELL, HIT THE PRY-BAR CAUSING THE PRY-BAR TO HIT THE EMPLOYEE IN THE FACE AND LIPS.

EMPLOYEE WAS TRYING TO TURN SMALL BOLT IN RATCHET-TYPE WRENCH, KNIFE SLIPPED, STRUCK KNIFE IN BASE OF THUMB ON LEFT HAND REQUIRING 1 SUTURE.

EMPL DISLODGING CHOKEUP IN CRUSHER WITH CROWBAR PULLED TOO HARD ON CROWBAR,CAUSING PULLED MUSCLE IN LOWER BACK.

PIPE ON TOP OF SAND TANK WAS CHOKED. EMPLOYEE TRIED TO UNCOKE, OPENED PIPE. CONTENTS OF PIPE SNAD AND WATER SPEWED INTO EMPLOYEES FACE AND EYES. EMPLOYEE USED EYE WASH IN PLANT, BUT STILL FE LT GRIT IN RIGHT EYE.

EMPL WAS INSTALLING NEW STRIKER BAR ON DRILL USING PIECE OF STEEL AS DRIVING BAR TO TIGHTEN ATTACHMENT. WHEN STRUCK BY HAMMER SMALLL PARTICLE OF STEEL BROKE OFF & HIT EMPL ON CHIN.

EMPLOYEE WAS TIGHTENING BOLTS ON RODMILL WRENCH SLIPPED CAUGHT THUMB BETWEEN WRENCH AND GUARD ON RODMILL,MASHED THUMBNAIL PARTIALLY OFF ON LEFT HUMB REQUIRING REMOVAL OF THUMBNAIL.

EMPL WAS BAGGING FELDSPAR HIS REGULAR JOB. BAGGING MACHINE STUCK BLEW DUST ONTO EMPL & INTOI HIS PANTS POCKETS WHERE HIS POCKETKNIFE WAS FULL OF DUST. WHILE EMPL WAS CLEANING KNIVE HE CUT H IS FINGER REQUIRING 4 SUTURES.

FOUR EMPLOYEE S WERE LIFTING AN ELECTRIC MOTOR DXX FROM A DUST COLLECTOR WITH A ROPE ONE EMPLOYEE LIFTED MORE QUICKLY THAT THE OTHERS AND CAUSED MOTOR TO SWING TOWARD SIDE WHERE EMPLOYEE WHO W AS INJURED WAS LIFTING CAUSING HIM TO CATCH HIS FINGER BETWEEN THE MOTOR AND THE FRAME.

EMP WAS CHANGIN1 SAND LINES. A WIRE LOOP BROKE AND LET A BAR SLIP OUT WHICH CAUGHT HIS FINGER BETWEEN THE BAR AND MOTOR BASE, MASHING FINGER AND FRACTURING IT, REQIRING REMOVAL OF FINGERNAIL AND SUTURES 3

I,NAME WAS HELP3NG OTHER EMPLOYEE PUT METAL DOOR BACK ON MICA BIN AND IN THE PROCESS AT TIGHTENING THE BOLTS THE WRENCH SLIPPED OF THE BOLT AND PINCHED HIS FINGER AGAINST THE METAL PLATE.

EMPL RAISING CO3VEYOR BELT SUSPENDED ON WINCH CABLE AND EMPL WAS HIT ON LEFT HAND BY FLY-BACK OF WINCH HANDLE.

EMPLOYEE WAS HE5PING CHANGE BEARINGS ON FEEDSCREW WRENCH SLIPPED CAUSING EMPLOYEE TO HIT ELBOW ON FEEDSCREW SEVERAL DAYS LATER INFECTION SET UP IN ELBOW JOINT REQUIRING LANCING ON 6-1-86

EMPLOYEE WAS RE4OVING TAPE FROM AROUND ELECTRICAL CONNECTIONS ON ELECTRIC MOTOR WITH KNIFE IN RIGHT HAND WHICH WAS USED TO CUT TAPE, LEFT HAND SLIPPED WHEN TAPE CAME OFF OF CONNECTIONS. EITHER KNIFE OR WIRE 7UT LEFT PALM.

EMPLOYEE WAS SHOVELING GRAVEL FROM UNDER CONVEYOR BELT A BLISTER FORMED ON HIS LEFT HAND WHICH BROKE ALLOWING SMALL PIECE OF STONE TO ENTER PALM OF HAND NEAR BASE OF THUMB WAS REMOVED 10-23-85 REQUIRED 3 SUTURES

EMPLOYEE WAS SHOVELING SPILLAGE FROM UNBDER HARDINGE MILL. IN THE PROCESS EMPLOYEE HAT TO GO THRU RAILINGS THAT SURROUND THE MILL AND IN SO DOING HIT HIS LEFT KNEE ON THE RAILING.

EMPLOYEE WAS CHANGING TRACTION WHEEL ON TOP OF ELEVATOR AND HAD PUT BAR THROUGH ELEVATOR CHAIN AND HITCHED IT TO A COMEALONG TO HOLD THE CHAIN IN POSITION. THE BAR SLIPPED OUT LETTING THE CHAIN FALL CATCHING EMPLOYEE\S LEFT HAND, HURTING HAND, REQUIRING 5 STITCHES.