Buscar en el registro

Employee was trying to open the gate to a bin with a sledge hammer and missed and struck finger.

EE drove the cat skidloader to the shop to take bucket off and put the forks on. EE put front of bucket on the ground, could not get pins out to release the bucket. EE used a hammer to hit the pin. Once EE did that, the back of the bucket fell onto EE's foot.

Employee was cutting a skirt board rubber with a utility knife when the knife cut his right leg just above the knee. He was on his knees cutting the skirt board rubber pulling the knife towards his knee when the knife slipped off the rubber and cut his leg. He was taken to the emergency room for treatment where he received 1 stitch.

Employee was working with hand tools disassembling commercial crusher. Employee while using a pry bar, pulled/ strained back muscle.

WHILE SHOVELING SAND TO MAKE SMALL TRENCH HE TWISTED AROUND TO DUMP SHOVEL WHEN BACK MADE POPPING SOUND LIKE BREAKING A STICK. LOWER LEFT SIDE OF BACK WAS VERY PAINFUL BUT COMPLETED WORK DAY & WENT HOME.DECIDED LATER THAT NITE TO GO TO E.R. WHERE DR. EXAMINED & PRESCRIBED MEDS WITH LIGHT DUTY. WAS TOLD IF PAIN PERSISTS TO SEEK FURTHER MEDICAL ATTENTION.

EE was cutting the outer jacket off of a piece of wire, holding the wire with his right hand and the utility knife in his left hand slicing back towards his right hand. The utility knife slipped and continued through his right thumb. Resulting in a cut requiring 11 stitches.

EE was using a 3"x3"x1/4" angle at 6" long as a pry bar to lift an 8' H beam at 30' long. His back popped causing him to seek medical attention right away. Doctor subscribed 3 medications for spasms and wants to see him again in two days.

EE was cleaning out (scraping) a lime chute behind the short head crusher. He heard a "pop" sound from his left bicep, and it started hurting. He called the plant supervisor to report it, but thought it would get better. It continued to hurt him so the supervisor took him to the med center.

Employee was lifting a 1.50" wash down hose up from side of wash bin to wash out a classifier tank & sand screw, the hose had been lowered over the side of the bin to drain so it wouldn't freeze, and evidently some water remained in the hose & froze. The hose was heavier than normal.

The men were attempting to replace a bearing on the yarder. EE was swinging a sledge hammer at a gear puller several times. On the last swing, the hammer missed its mark, causing his arm to travel further around. His left forearm struck a pipe hand rail that had been cut off with a pipe cutter prior to the beginning of the shift. This laceration required 8 staples.

While working on the bushhog mower gear box, EE was holding the shaft while another was driving it out with a hammer. When shaft moved injured's small finger was smashed between the shaft and the floor.

EE was unpluging split master on 6x16 with a bar slipped and hurt his back.

While working on a small pull-behind trailer, employee was attempting to raise the front of the trailer up. While he was cranking the jack handle around, the handle broke causing him to move forward and slash the underside of his right arm on the crank shaft that was left sticking up. He received sixteen stitches.

While trying to loosen a sheave, employee placed a block of wood against it. While still holding the block of wood a co-worker proceeded to swing the sledge hammer striking EE's finger & smashing it causing a fracture to his middle finger.

EMPLOYEE WAS USING SLEDGE HAMMER TO DRIVE WEDGES IN A CRUSHER THAT WAS BEING REMOVED AND PULLED A MUSCLE IN HIS RIGHT ARM.

Hot and muddy weather. working at splicing and cutting rubber belting he keep wiping persperation from his face. his eyes became irratated and washed them with eye. wash several time thinking it was only idrt. moring reported this againa and finally saught medical advice, found several metal objects embedded in his left eye

NO UNSAFE CONDITIONS EXISTED, EMPLOYEE SAID HE STRAINED HIS BACK REPLACING WIPERS ON WEST PLANT THOR CONVEYOR, EMPLOYEE WAS LOOSENING BOLTS THAT HOLD RUBBER WIPER IN PLACE MOVED AND STRAINED BACK.

ADJUSTING CRUSHER BOLTS WITH HAMMER AND WRENCH. WRENCH SLIPPED AND FINGER GOT BETWEEN BOLTS AND WRENCH SMASHING FINGER.

PRYING METAL FORM OFF OF CONCRETE WITH PRY BAR, FORMS FELL ON LEG.

EE WAS USING A UTILITY KNIFE TO CUT THE RUBBER/WIRE STRAPS ON CONVEYOR BELTING AT THE OLD GRAVEL PLANT. HE WAS TRYING TO CUT IT IN ONE PASS, WHICH CAUSED THE KNIFE TO COME BACK TOO FAR AND TOO FAST, HITTING HIS RIGHT KNEE. THE KNIFE SLICED OPEN AND AREA APPROX. 3" LONG ON HIS RIGHT KNEE CAP.

EMPLOYEE WAS DISLODGING A LARGE OBJECT FROM FEEDER TUNNEL. HE WAS USING A PRY BAR PULLING ON IT WHEN THE OBJECT CAME LOOSE HIS HAND BECAME SMASHED BETWEEN A METAL OBJECT AND THE BAR CAUSING HI M TO SMASH HIS THUMB.

HE WAS PRYING OPEN A SLIDE DOOR ON AN AUGER WITHA PIPE. HE FELT LIKE HE PULLED A MUSCLE.

EE WAS CUTTING CONVEYOR BELT WITH A UTILITY KNIFE. THE KNIFE SLIPPED, RUNNING OVER THE TOP OF HIS LEFT HAND. IT SLICED HIS INDEX FINGER, MIDDLE FINGER, AND RING FINGER OF THE LEFT HAND. HE WAS BLEEDING CONSIDERABLY, AND WAS TAKEN TO CLINIC IMMEDIATELY BY A FELLOW EE. THE CUT WAS CLEANED, HE RECEIVED 8 STITCHES, A METAL SPLINT WAS PLACED ON RING FINGER, AND ALL FINGERS WERE WRAPPED.

WHILE CUTTING CONVEYOR BELTING IWTH A POCKET KNIFE, EE CUT TOWARDS HIMSELF AND STABBED HIMSELF INT HE LEG JUST ABOVE HIS KNEE, WITH THE BLAD GOING DOWN TOWARDS THE BACK OF HIS KNEE CAP.

WORKER WAS USING SLEDGEHAMMER TO TIGHTEN NUT ON TOP OF CRUSHER SHAFT & INJURED BACK

EE WAS REMOVING A BAD BEARING ON THE STONE PLANT WITH A HAMMER. HE WAS TRYING TO BREAK THE BEARING LOOSE FROM THE PULLEY SHAFT, AND A FRAGMENT OF METAL FLEW UP AND STRUCK HIS LEFT FOREARM. THE RE WAS A DROP OF BLOOD, AND HE THOUGHT IT JUST CUT THE SKIN. THAT NIGHT, THE ARM BEGAN TO ACHE AND HE NOTICE A KNOT AND SWELLING UNDER THE CUT. HE WENT TO THE MEDCENTER FOR XRAYS. EMBEDDED.

EMPLOYEE WAS WELDING ON A SCREEN USING SCALER TO CLEAN SLAG AND WELD. HE HAD SAFETY GLASSES ON AND WAS PREPARING WELD AREA. A PIECE OF MATERIAL WAS BLOWN IN BEHIND HIS GLASSES BY THE WIND. HE WENT TO EYE AREA, BRUSHED IT AWAY, THOUGHT IT WAS GONE. THE NEXT EVENING HIS EYE STARTED TO BECOME IRRITATED. WENT TO DOCTOR AND PRESCRIPTION WAS GIVEN.

JACKING ANGLE IN PLACE USING AN EXTENTION POST. PUT PRESSURE ON JACK AND JACK KREELED OUT STRIKING IN HEAD CUTTING HIS EYEBROW AND OPENING UP A WOUND THAT REQUIRED STITCHES.

EE'S WERE ADJUSTING DRIVE BELTS ON RETURN CONVEYOR. EE WAS HOLDING A BOLT WITH A 1/2" RATCHET 3/4 SOCKET. EE WS TRYING TO BREAK LOOSE A JAM NOT WHEN THE RATCHET SLIPPED PINNING EE'S FINGER A GAINST THE EDGE OF A FLAT STEEL GUARD CUTTING HIS FIGNER DEEPLY.

CHIP CAME OFF CHISEL

EMPLOYEE WAS TIGHTENING BOLTS ON THE SCREEN ON THE GRAVEL PLANT INSTALLED NEW SCREENS. THE WRENCH SLIPPED OFF OF THE BOLT, AND HIS HAND FLEW INTO THE BOLT. HIS GLOVE WAS NOT TORN, BUT THE IMPA CT CUT THE MIDDLE KNUCKLE OF HIS RIGHT RING FINGER. AT THE MEDCENTER THE DOCTOR CLEANED THE WOUND, APPLIEA A BUTTERFLY PATCH AND A METAL SPLINT TO KEEP THE FINGER FROM MOVING. HE WAS ALSO GIV

FOUR MEN WERE USING TWO CHAIN WRENCHES TO TIGHTEN AN 8 INCH PIPE COUPLING WHEN ONE OF THE CHAINS BROKE LETTING THE WRENCH DROP TO THE FLOOR PINCHING THE FINGER OF EMPLOYEE.

CUT LEFT HAND CUTTING RIDLE RUBBER FOR SCREEN

INSTALLING CAB ON 980C LOADER, EE GOT FINGERS BETWEEN CAB & CABN MOUNTS ON MACHINE. THE OTHER MECHANIC HELPING, PRIED CAB OVER TO HELP LINE UP TO THE MOUNTS, PINCHING EE'S FINGERS BETWEEN THE CAB & MOUNTS.

HE WAS CUTTING CONVEYOR BELT WITH A RAZOR KNIFE. KNIFE SLIPPED AND CUT INTO LEFT FOREARM.

TAKING A BEARING OFF THE SHAFT ON A KOLBERG SCREEN WITH A HAMMER. A PIECE OF METAL CAME OFF THE BEARING CUT FOREHEAD.

EE WAS USING A WRENCH TO TIGHTEN THE SCREEN CLOTH ON THE FIRST SCREEN AT THE PLANT. THE WRENCH SLIPPED, AND HIT HIM UNDER THE LEFT JAW, CHIPPING/BREAKING OFF A PIECE OF HIS BACK TOOTH ON THE L EFT SIDE.

WHILE WORKING OUTSIDE IN COLD WEATHER, HE WAS IN THE PROCESS OF CHANGING AN ENGINE AND TRANSMISSION ON A 757 TON HAUL UNIT. THIS REQUIRED HEAVY LIFTING, HEAVY WRENCH USED AND USING PULL BARS. HE DEVELOPED A SORENESS IN HIS RIGHT SHOULDER, THINKING COLD WEATHER WAS THE MAIN CAUSE. AS TIME HAS PROGRESS THIS SORENESS INCREASED WITH FURTHER UUSE OF WRENCHES. WHICH FINALLY CAUSED

EMPLOYEE WAS GETTING READY TO REMOVE A PIECE OF PLATE STEEL FROM STEEL RACK WITH PLATE CLAMP. HE PRIED THE PIECE OF PLATE OUT OF INSTALL PLATE CLAMP AND IN SO DOING DISLODGED ANOTHER PLATE TH AT WAS CAUGHT ON BONDING CLAMP CAUSING IT TO FALL 2" DOWN ON TOP OF HIS FOOT.

HOLDING WRENCH TO TIGHTEN BOLT, ANOTHER EE WENT TO HIT THE BOLT WITH A SLEDGE HAMMER. SLEDGE HAMMER CAME DOWN ON RIGHT HAND.

MEN WORKING ON JAW CRUSHER USED A COMALONG TO PULL JAW BACK FROMCLEARANCE TO WORK ON TOGGLE BEARING WHEN WELD ON EYELET BROKE ALLOWING JAW TO SWING FREE CRUSHING EE FOOT

EE WAS GREASING THE MOBILE EQUIPMENT THE PREUMATIC GREASE GUN WAS EMPTY EE WAS CHANGING THE GREASE GUN OVER A NEW PAIL OF GREASE EE WAS USING A SCREWDRIVER TO TAKE THE LID OFF OF THE PAIL THE SCREWDRIVER SLIPPED & HIS FINGER WAS CUT ON THE LID

PULLING ON 1IN DRIVE RATCHET WRENCH HURT BACK

WORKING ON EUCLID TRUCK AND PAINT CHIP GOT IN RIGHT EYE. REMOVE PART OF PAINT CHIP AT THAT TIME, 3/8/95 RIGHT EYE STILL IRRITATED, WENT TO AMBUCARE CLINIC.

EE HELPING CRUSHER OPERATOR REMOVE ROCK FROM CRUSHER PLATFORM. REMOVING ROCK WITH CHAIN HOIST, HOIST SLIP, ROCK STRIKING BAR LAYING ON PLATFORM. BAR FLIP STRIKING EE'S KNEE.

INJURED WAS BEATING ON THE GATE OF THE HOPPER TO RELEASE STONE, WHEN A PIECE OF STEEL WENT INTO HSI LEFT EYE.

EMPLOYEE WAS WELDING ON BIN AT MILL & TRIED TO STRAIGHTEN A PIECE OF METAL WITH A RAILROAD BAR. BAR FLIPPED BACK & CAUGHT EMPLOYEE IN JAW, REQUIRINTG STITCHES.

CUT FINGER WITH UTILITY BOX CUTTER. HE WAS CUTTING BOTTOM OUT OF A PLASTIC OIL CAN. THE INJURY REQUIRED STITCHES.

CUTTING PIPE, PIECE FELL, HITTING MAN ON LEFT ANKLE.