Buscar en el registro

unspecified metacarpal bone fracture while performing housekeeping

EE was attempting to enlarge a hole on a rubber skirt. The knife EE was using slipped and cut the web of EE's other hand. The EE received one (1) suture in their hand.

Employee's right finger was pinched between a come along and a metal plate causing a break to occur requiring a splint and restrictions.

Employee's right little finger was caught between digging bar and back plate resulting in a laceration requiring stitches and a fracture to the finger.

While using a retractable utility knife, contact was made between the blade and employee's right knee causing a laceration.

While hammering a bucket guard on a loader a small piece of metal broke off and went into the employee's leg.

The injured worker was removing a failed pillow block bearing from a shaft. He struck the bearing housing with a hammer in an attempt to break the housing for easier removal. A small shard of metal struck him in the lower right part of his cheek and became imbedded. The IW went to the ER where a physician removed the object. The IW returned to full duty work.

IE was assisting a fellow EE in the removal of a water pump. It was being lifted with the aid of a come-a-long. It appears there was a mechanical failure in the lifting device that caused the pump to drop suddenly. When the pump dropped it jerked his arm as he was holding onto the chain guiding the pump. This caused a strain to his right arm. He returned to modified duty.

Employee was doing maintenance on a crusher and caught his finger between bar and side of crusher

EE was trying to unplug the chute on the jaw crusher when a plate fell down in the chute and he was using a prybar to try to pry the plate loose when his finger got caught between the bar and the chute. This pinched his middle finger on his left hand. His finger is fractured.

Pocket knife in hand, cutting tie strap, knife slipped cutting left hand between thumb and index finger.

Conveyor belt needed a small piece cut off of it. Employee had a utility knife, pulling it towards himself slipping off of belt & cutting himself.

EMPLOYEE WAS SPLITTING STONE WITH A HAMMER & CHISEL. HE ACCIDENTALLY HIT HIS HAND WITH THE HAMMER.

EMPLOYEE WAS TAKING GREASE FITTING OUT OF ADJUSTMENT CYLINDER FOR TAILPULLEY & PRESSURE IN CYLINDER SHOT GREASE FITTING INTO HIS LEFT HAND BETWEEN INDEX & MIDDLE FINGER CAUSING PUNCTURE WOUND.

INJURED WAS HOLDING A DRIFT PIN AND CO-WORKER WAS SWINGING A SLEDGE HAMMER AT IT, WHEN HE STRUCK HIS THUMB WITH THE HAMMER.

EE WAS TRIMMING BELTING TO FIT BACK OF SCREEN WITH A UTILITY KNIFE. EE WAS KNEELING AND KNIFE WENT THRU BELTING AND CUT HIS INNER THIGH ON HIS LEFT LEG.

EE WAS TORQUEING BOLTS TO 475 FT. LBS. ON WAS SCREEN WITH A TORQUE WRENCH WHEN IT SLIPPED A GEAR CAUSING EE TO INJURE HIS SHOULDER.

EE SAW BIG HUNK OF MUD ALONG SIDE OF BELT. HE WANTED TO PUSH IT OUT. BELT WAS STOPPED. HE PICKED UP MUD FORK AND INVERTED IT TO POKE IT THROUGH. PUSHED FORWARD AND SPIKE OF FORK HIT OUTER EAR RIGHT.

EE WAS REMOVING ANVILS FROM CRUSHER ANVIL RING WITH SLEDGE HAMMER CAUSING A PIECE OF ANVIL TO BREAK OFF AND HIT VICTIM IN LEFT KNEE GIVING HIM A LACERATION THAT TOOK 3 STITCHES ON INSIDE AND 3 STITCHES ON OUTSIDE.

EE WAS USING A UTILITY KNIFE TO CUT SKIRTING FOR THE CONE BELT. HE WAS CUTTING A PIECE OF BELTING AND THE KNIFE SLIPPED BACK AND CUT HIS RIGHT KNEE.

WORKING AS PLANT HELPER CLEANING OUT CHUTE AT SECONDARY PLANT AT C-21 CONVEYOR DRY SCREENING CHUTE BLOCKED STANDING ON PIECE OF FLAT BAR DIGGING CHUTE OPEN SLIPPED OFF FLAT BAR LANDING WRONG O N HIS RIGHT ANKLE. CONDITIONS WERE WET AND MUDDY

EE WAS USING PRY BAR TO PRY A PIECE OF METAL TO BE WELDED WHEN BAR SLIPPED CAME BACK AND HIT HIMIN UPPER LIP

EMPLOYEE WAS ATTEPTING TO PRY WITH A 15" PRY BAR HYDRAULIC MECHANISM ON CRUSHER WHEN BAR SLIPPED AND SMASHED SMALL FINGER BETWEEN BAR AND HAND RAILING.

WHILE STEMMING BOREHOLE, EE FELT A SNAP IN HIS BACK. HE TRIED HEAT & FLEXALL BUT IT DIDNT DO ANY GOOD.

TOOK A UTILITY KNIFE AND WAS CUTTING THE HOSE WHEN INADVERTENTLY THE KNIFE CAME OFF THE HOSE CUTTING THE LEFT INDEX FINGER. THE EMPLOYEE WAS HOLDING THE HOSE IN LEFT HAND PULLING KNIFE TO HIM

EE WAS BACKING OFF A NUT ON A SCREEN BOLT AT WASH PLANT. THE TIME WAS 800 PM THE BOLT HE WAS WORKING ON HAD PAINT ON THE THREADS MAKING IT DIFFICULT TO TURN THE NUT. IN THE PROCESS THE SOCKET SLIPPED OFF THE NUT. THE FORCE OF HIS WEIGHT SLAMMED HIS FIFTH FINGER ON HIS RIGHT HAND INTO THE FRAM EWORK OF THE SCREEN.

EE WAS PUTTING UP "NO TRESPASSING" SIGNS. HE WAS USING A SLEDGE HAMMER TO POUND THE STAKE INTO THE GROUND WHEN THE HAMMER SLIPPED OFF THE STAKE STRIKING THE RIGHT INDEX FINGER. IT CUT THE TIP OF HIS RIGHT INDEX FINGER. THEY PUT STITCHES IN IT.

BAR BROKE ON CRUSHER. EE WAS TURNING BAR ON IMPELLER WHEN BAR CAUGHT THUMB ON RIGHT HAND.

EE WHILE ATTEMPTING TO REMOVE A PIECE OF STEEL ANGLE, USED AS A WEDGE, THIS ANGLE WAS RIGHT IN BETWEEN 2 PLATES. WHEN HIT WITH THE HAMMER, ANGLE GOT DISLODGED ADN HIT EE IN THE BRIDGE OF NOSE. STITCHES REQUIRED.

EMPLOYEE HAD USED PORTA POWER TO PUSH OUT CENTER BUSHINGS ON THE FRAME OF FRONT END LOADER. THE PORTA POWER WAS BEING MOVED WHEN IT SLIPPED FROM HIS HANDS AND SMASHED HIS FIRST FINGER ON HIS L EFT HAND ON FRAME OF LOADER. THE HOSPITAL CLEANED, STITCHES AND X-RAYED END OF FINGER.

EE WAS SHOVELING MATERIAL WHEN HE TURNED TO EMPTY SHOVEL, HIS FOOT DID NOT TURN CAUSING THE INJURY TO HIS RIGHT KNEE.

EE WAS INSIDE A CHUTE DIGGING OUT FROZEN MATERIAL WITH A DIGGING BAR, IN AN UP AND DOWN MOTION WHEN HIS RIGHT HAND STRUCK A PIECE OF PIPE ABOVE HIS HEAD CAUSING THE INJURY.

EE WAS POKING MUD WITH A BAR WHEN THE BAR SLIPPED AND HE BANGED HIS LEFT ELBOW ON THE SIDE OF THE CHUTE.

EMPLOYEE WAS WORKING ON A COME-ALONG (TOOL FOR HOISTING EQUIP.), THE CABLE JAMMED WHEN IT CAME LOOSE AND TWISTED HIS LEFT KNEE.

VICTIM AND COWORKER WERE PREPARING TO OPEN CHUTE/DOOR AT DISCHARGE END OF VIBRATING SCREEN TO GAIN ACCESS TO 2ND DECK, COWORKER CALLED AWAY TO ANSWER PAGE, VICTIM TRIED TO OPEN DOOR BY USING A COME-A-ALONG. HE BRUSHED STONE OFF DOOR TO PREVENT CONTAMINATION ON 1/2" PRODUCT BIN. HE REMOVED COME-A-ALONG FROM LIFTING EYE WHICH MEANT HE HAD TO BALANCE DOOR, WHEN IT GOT AWAY FROM HIM, F

YEMPLOYEE WAS WORKING IN GARAGE AREA TAKING BELL HOUSING OFF OF ENGINE. THE BELL HOUSING HIT THE FLOOR AND HIS HAND WAS UNDERNEATH. HE RECEIVED A LACERATION OF TH ERIGHT INDEX FINGER.

EE WAS HELPING ANOTHER EE LOOSEN BOLTS IN A MOTOR BASE SO BELTS ON MOTOR COULD BE ADJUSTED. HE WAS IN A SITTING POSITION AND PULLING ON A LARGE 1 1/2 WRENCH OPEN BOX END. HE PULLED HIS UPPER C HEST MUSCLE.

EE WAS USING A STEEL PIN DRIVER TO TIGHTEN THE CAP ON A HOIST CYLINDER FOR A 65 TON TRUCK. EE WAS STIKING DRIVER WITH HAMMER WHEN A PIECE OF STEEL BROKE OFF DRIVER AND STUCK UPPER THIGH OF LEF T LEG.

EMPLOYEE WAS SWINGING SLEDGE HAMMER TO POUND IN A WEDGE ON THE LOCKOUT POST ON CONE CRUSHER. HIS KNEE BUCKELD WHILE HE WAS SWINGING. THEN ON 10-13-94 EMPLOYEE WAS WALKING UP STEPS AT JADAIR CL ARIFIER AND HIS KNEE BLEW OUT. HE WILL BE GETTING IT OPERATED ON 10-31-94. THERE WILL BE LOST TIME AFTER THE OPERATION.

HEAVY WRENCH FELL ON FINGER WHILE PUTTING WRENCH ON PIPE.

INJURED EMPLOYEE AND CO-WORKER AFTER GETTING A SECTION OF PLATE STEEL WERE STACKING 4X8 SHEETS BACK ON ENED. THE STEEL WSAS IN A BUILDING AND ADJACENT TO APUMP MOUNTED ON A TRAILER. WHEN THE Y HAD THE STEEL BACK UPRIGHT THEY TRIED PRYING THE BOTTOMS AWAY FROMT HE WALL TO ACHIEVE PITCH AND STABILITY, BUT THE STEEL SHIFTED OVERCAME THE STRENGTH OF EMPLOYEE AND PINCHED HIS LEG BETWEE

EMPLOYEE WAS TAKING DECK OFF SWEEPER BROOM. HE WAS PULLIGN ONA NUT ON A BOLT WITH OPEN END WRENCH. T HE WRENCH SLIPPED CAUSING INJURED TO BUMP RIGHT ELBOW. HE WAS LAYING ON A PORTION OF THE DECK IN A FAIRLEY CONFINED AREA.

EMPLOYEE WAS LOADING WITH SHOVEL AND DIRT FLEW IN RIGHT EYE. THEY REMOVED A PIECE OF STONE FROMHIS RIGHT EYE.

EE WAS OPENING A BLOCKED CHUTE. THERE WAS A BLOCKED CHUTE WITH LARGE 10" MINUS ROCKS IN IT. EE WAS USING 3/4" ROD APPROX. 6' LONG POKING IN THE CHUTE WITH HIS HANDS UP INSIDE THE CUTE, WHEN TH E BRIDGE MATERIAL BROKE LOOSE AND STRUCK THE VICTIM ON HIS LEFT HAND BEFORE HE COULD MOVE IT HIS HAND.

EMPLOYEE WAS WORKING ON 80D SHOVEL. HE WAS TAKING THE TRACKS OFF THE MACHINE. THEY HAD LOOSENED THE BOLTS AND WERE TRYING TO TAKE THEM OUT OF THE MACHINE. THE BOLTS DID NOT WANT TO COME OUT SO THE EMPLOYEE STRUCK THE HEADS WITH A HAND HELD HAMMER SEVEREAL TIMES AND FRAGMENTS OF STEEL FLEW INTO THE FLESHY PART OF HIS CHEEK ON THE RIGHT SIDE OF HIS FACE.

INJURED WAS USING A COME-A-LONG TO BRING THE GRATES IN THE BACK DOOR OF THE CRUSHER. WHEN THE GRATE CLEARED THE DOOR IT SWUNG OVER AND HIT INJURED IN THE LEFT ANKLE, PINNING IT AGAINST THE WAL L OF THE CRUSHER.

EMPLOYEE WAS TIGHTENING A BOLT WITH A WRENCH. BOLT BROKE FREE CAUSING HIM TO PINCH RIGHT INDEX FINGER.

HE CLAIMED WHILE HE WAS ON TOP OF AN INVERTED LOADER BUCKET PULLING ON A LEVER OPERATED COME-ALONG THAT HE WAS USING TO PULL A CUTTING EDGE INTO POSITION. ONE OF THE CLIPS THAT THE CHAIN WAS H OOKED TO BROKE LOOSE CAUSING A SUDDEN RELEASE OF PRESSURE. HE LOST HIS BALANCE, SHIFTED AND FELL FROM THE BUCKET ABOUT 5 FEET ONTO THE FLOOR STRIKING HIS HEAD AND SHOULDER ON THE CONCRETE.

TRYING TO GET THE ROTOR TO TURN WITH A COME-ALONG HOOKED BETWEEN 2 LIFTING EYES: ONE WELDED ON FEED PLATE AND ONE WELDED ON THE ROTOR. THE EYE ON THE ROTOR BROKE LOOSE AND FLEW BACK,STRUCK RIG HT LEG BETWEEN ANKLE AND KNEE LEAVING A CUT AND BAD BRUISE.WOUND BECAME INFECTED AND RESULTED IN DR VISIT 5-6-92.

EMPO\LOYEE WAS TIGHTENING BOLTS ON A CRUSHER. THE EMPLOYEE TRIED TO MAKE THE BOLTS TIGHTER BY PUSHING ON A BAR WITH HIS FEET. HE HAD HIMSELF IN AN ODD POSITION. THIS RESULTED IN A STRAIN TO HI S LOWER BACK.