Buscar en el registro

Cut back of hand with utility knife while cutting old conveyor belt.

Tightening head on kelly bar on drill with wrench, wrench slipped and employee moved akwardly and felt pain in lower back.

Employee received a piece of metal, embedded in his upper thigh area, from removing teeth from a loader.

Employee was opening a box with a box cutter. As the employee turned the box around, on the third turn, he accidently lost control of knife as it came towards his left arm. The knife lacerated the left wrist and at the same time puncturing an artery.

Technican attempting to cut wiring harness with knife. Knife slipped and cut finger.

The Counterweight did not line up with the saddle, a come-along was attached to the frame on the conveyor. He took a closer look to see what it was hanging up on and in the process put his hand on the frame of the take-up system, the weight shifted catching the tip of the middle and ring finger on his right hand between the frame and the weight.

Striking the hammer against the chisel cause a small piece of the hammer face to came off and went into index finger on left hand.

He was attempting to dislodge a rock in the winged tail pulley with a long piece of flat bar. He pulled down on the bar, the end of the bar rolled out of the tail area, the flat bar smashed his left index (pointing) finger resulting in a broken bone, 5 stitches. He was wearing gloves on his hands at the time.

Employee was removing driveshaft from 972 loader. Employee was striking driveshaft T with hammer to remove from yoke. At the area of impact on the bearing cap a piece of metal broke free from the cap and punctured right calf of employee. Size of metal was approximately eigth of an inch in diameter.

Employee was splicing the wire for the installation of a replacement light fixture on the #2 Hazemag crusher, as he was cutting off the outer cover of the cable the knife slipped and cut his thumb.

Employee was working on a feed throat for a FM. While trying to clear the plug with a sledge hammer and rod, employee smashed his hand causing laceration and fracture to right middle finger.

Employee cut right index finger while removing zip tie.

Employee was changing a bearing on the stedman with a portapower jack and while pushing off the bearing the ram popped out and hit him in the jaw area. NOTE: (Employee did not seek any treatment at the time due to mild pain and did not seek medical treatment until 8-29-2005: and was then taken to workers Compensation for treatment)

Moving a cable tree when the chain used to move the tree slipped and pinched the employee's finger.

Employee was clearing a plug on the FK Pump for #3 finish mill. He had cleaned out the pump and screw and was working on the flapper when cement that was in the line to the silo came back down the pipe and hit him. It knocked off his hat and glasses and got into both eyes. He wasn't wearing goggles as required.

Employee was removing plastic zip ties from computer cables and in doing so cut left wrist with knife.

Employee was removing a bearing sleeve from a shaft with a hammer and a shard of metal broke off and cut the employees left arm.

EE STRUCK HIMSELF IN THE MOUTH WITH A WRENCH WHILE PERFORMING MAINTENANCE REPAIRS.

EE WAS ADJUSTING THE FEED END AIR SEAL ON KILN USING A PORTAPOWER. THE SEAL SHIFTED QUICKLY AND DISLODGED SOME KILN DUST THAT ENTERED THROUGH THE GOGGLES AND INTO HIS EYES.

EE WAS MOVING HAMMERS IN THE STEDMAN WITH A PRY BAR WHEN THE HAMMER JUMPED OVER THE RAIL. EE GRABBED THE HAMMER TO KEEP IT FROM FALLING OFF THE TABLE AND STRAINED HIS BACK.

EE WAS HELPING INSTALL A PIPE UNDER A CLASSIFIER SYSTEM WHILE USING A CROWBAR TO APPLY PRESSURE TO KEEP PIPE IN SLOT SO IT COULD BE CLAMPED, WHEN HE PULLED HIS LUMBAR MUSCLE.

WHILE UNDOING BOLTS FROM MACHINE, A PIECE OF A RUSTY METAL BOLT GOT INTO THE EMPLOYEES RIGHT EYE.

EE WAS CUTTING BAND ON A BUNDLE OF EMPTY BAGS. HE WAS PULLING THE KNIFE TOWARDS HIM. WHEN HE CUT THROUGH THE STRAP THE KNIFE CONTINUED ON AND HE STABBED HIMSELF ON THE INSIDE OF HIS LEFT THIGH .

EE WAS CUTTING BUT HAD HIS LEFT HAND DIRECTLY ACROSS FROM HIM. THE CUTTING UTENSIL SLIPPED AND HE CUT HIS LEFT THUMB. (THE DELAY IN REPORTING THIS WAS NOTED DURING AN INTERAL AUDIT).

WHILE ATTEMPTING TO KNOCK A TOOTH OUT OF A LOADER BUCKET A METAL FRAGMENT PUNCTURED HIS RIGHT ARM.

WHILE HAMMERING METAL WITH A SLEDGE HAMMER A PIECE OF METAL FLEW OFF AND STRUCK HIS RIGHT LOWER LEG CAUSING A PUNCTURE WOUND.

EE WAS REPLACING THE COUPLING BETWEEN THE CUTTER HEAD MOTOR AND GEAR BOX. WHILE DRIVING THE COUPLING ON W/ A HAMMER, HIS HAND SLIPPED AND HE STRUCK HI LEFT THUMB.

A FUEL/LUBE TRUCK DRIVER WAS CHANGING THE TEETH ON A 990 LOADER, USING A HAMMER 3 LB WHEN UPON STRIKING THE PIN A METAL PIECE HIT HIS UPPER LEFT LEG.

EE WAS USING A CHISEL BRAND NEW TO SPREAD LINKS ON A TRACK SYSTEM. THE CHISEL SNAPPED IN HALF AND CUT HIM ABOVE THE RIGHT EYEBROW.

EMPLOYEE WAS SWINGING A SLEDGE HAMMER WHILE DOING MAINTENANCE IN THE PLANT AND STRAINED HIS RIB CAGE.

EE WAS WORKING ON A CRUSHER. HE GOT A PRYBAR STUCK TRYING TO REMOVE A CHIPPING HAMMER. HE COULD NOT GET HAMMER OUT SO HE THREW PRYBAR DOWN ON GROUND. WHEN HE THROW PRYBAR DOWN A PIECE OF METAL WENT INTO TO HIS LEFT EYE. NO SAFETY GLASSES BEING WORN AT TIME.

EE SUSTAINED A SEVERE LACERATION TO HIS FACE WHEN TIGHTENING A BOLT WITH A WRENCH AND IT SLIPPEDSTRIKING HIS FACE.

EE WAS ADJUSTING IDLER ON CONVEYOR WITH HAMMER WHEN HE SWUNG HAMMER AND MISSED, STRAINING HIS BICEP.

EMPLOYEE WAS TIGHTENING BOLT WITH A WRENCH WHEN HAND SLIPPED AND STRUCK METAL-LACERATING HAND.

EE WAS ATTEMPTING TO GET A BEARING OUT OF ITS PACKAGING BY HITTING THE BOX WITH A HAMMER. UPON DOIN SO, A FRAGMENT OF METAL SHOT OUT AND STRUCK HIM IN THE RIGHT LEG. IT WAS EMBEDDED IN HIS RIG HT SHIN BONE.

EMPLOYEE WAS SHIFTING A PIECE OF RAIL WITH A PRY BAR AND STRAINED HIS LOWER BACK.

MAINTENANCE ON DRAGLINE.

EE WAS CUTTING SKIRT RUBBER. WHEN CUTTING HE WAS PULLING THE BELT KNIFE TOWARD HIMSELF, AND CUT LEFT LEG.

EE WAS CUTTING ELECTRICAL CABLE SPLICE W/UTILITYKNIFE WHEN BLADE SLIPPED AND LACERATED EE'S LEFT THIGH REQURING SUTURES

EMPLOYEE WAS USING PRYBAR TO CLOSE RAIL CAR DOORS. BAR SLIPPED OUT OF DOOR AND EMPLOYEE LOST HIS FOOTING AND TWISTED HIS ANKLE.

EMPLOYEE WAS CHANGING BELTS ON 500 HP MOTOR ATTACHED TO SPEED REDUCER. REDUCER WAS SUSPENDED BY A CHAIN AFTER BEING PULLED BACK BY A COME-A-LONG. THE CHAIN BROKE DROPPING REDUCER ONTO EMPLOYEE 'S HAND CAUSING LACERATION AND FRACTURE OF LEFT INDEX AND MIDDLE FINGER.

EMPLOYEE WAS TIGHTENING BOLTS ON CRUSHER DOOR WHILE PREPARING FOR PRODUCTION. WRENCH SLIPPED OFF OF BOLT AND STRUCK EMPLOYEE IN RIGHT CHEEK.

EMPLOYEE WAS CUTTING A PIECE OF CONVEYOR BELT, UTILITY KNIFE SLIPPED AND LACERATED EMPLOYEE'S RIGHT THIGH REQUIRING 3 STITCHES.

EMPLOYEE WAS VIGOROUSLY SHOVELIGN STONE OFF AN OVERLOADED CONVEYOR BELT WHEN HE FELT A PAIN IN HIS LOWER BACK. HE REQUESTED TREATMENT OF 6-6-96.

EMPLOYEE CUT BEARING HOUSING IN 2 PLACES TO REPLACE THE ENTIRE BEARING. HE TAPPED HOUSING WITH 2# HAMMER SO THAT HOUSING WOULD BREAK LOOSE AND FALL OFF. IN DOING SO A TINY STEEL FRAGMENT SPA LLED OFF AND FLEW INTO HIS LEFT THIGH.

EMPLOYEE WAS HLEPING TO CHANG HAMMERS IN STEDMAN CRUSHER. EACH HAMMER IS HIGH CHROMIUM MAGANESE STEEL WEIGHT ABOUT 375 LBS POUNDS. TO GET PROPER SIDE CLEARANCE ON A ROW OF 3 HAMMERS EMPLOYEE TAPPED THE EDGE OF THE END HAMMER WITH AN 8# SLEDGE. HE WAS BENDING OVER LOOKING DOWN AT HAMMEER. TINY STEEL FRAGMENT SPALLED FROM HAMMER AND FLEW INTO EMPLOYEES EYE. VISION WAS PERMANENTL

COME-A-LONG WAS IN USE LOWERING THE SHAFT TO THEPLATFORM, THEREFORE THE METAL PLATE FELL APPROX. 12 INCHES FROM THE PLATFORM HITTING THE EMPLOYEE. EMPLOYEE WAS REMOVING THE COUNTER WEIGHT FROM THE SCREEN TOWER #2. IN DOING SO, THE BEARING FELL OUT OF THE SOCKET, THEREAFTER THE ROUND METAL PLATE THAT HOLDS THE BEARING FELL OUT ON THE VITIM'S RIGHT ANKLE. RESULTS: ABRASION TO ANKLE.

EMP WAS SKINNING BACK SOME WIRES AND CUT RIGHT INDEX FINGER. HAD TO HAVE 3 STITCHES.

STRUCK CHISEL WITH HAMMER & TIN PIECE OF METAL SPALLED OFF & FLEW INTO UPPER RIGHT LEGFRAGMENT WAS REMOVED SUCCESSFULLY BY DOCTOR FIRST REQUEST ED TREATMENT ON 03-22-95

EMPLOYEE STRUCK RIGHT KNEE WITH HAMMER WHILE KNOCKING SLAG OFF NEWLY CUT STEEL PLATE REQUESTED MEDICAL TREATMENT ON 02-07-95