Buscar en el registro

Bottom kicked out on ladder setting on slope.

EE was dismounting tire from wheel using a bead breaker ram tool when bolts broke the tool struck EE on right side of head.

Adjusting cone on crusher. He was holding the cable and finger was caught between cable & pipe

Someone in tower turned belt on and did not know he was in the area.

Employee was helping to put a cutting edge on endloader. Instead of using a wrench to hold bolt head steady he held it with his hand. Air wrench was used by second employee and bolt spun in first employee's hand and cut his left thumb which required 3 stitches to fix.

Employee was driving a CAT 769 Haul Truck. Reached behind the seat to see if the cooling fan in the cab was running and stuck his finger inside the guard and cut tip of middle finger on right hand. Taken to hospital and stitched up.

A flop gate (75 lbs) at the end of a conveyor had rolled up and landed on the tail pulley. Two employees raised it up to let up back in position. One employee let go of his end after the gate went over center before the other and the gate pinched the right ring finger of the second employee against the angle iron that the gate swung in.

EE was attempting to remove a rock that had become lodged under the belt in a conveyor tailpulley using his hands to roll the belt forward. The rock dropped out and belt rolled back, pinching both hands. The little finger on his left hand was broke & the tip above the first joint was badly cut. He was taken to the hospital and the little finger was stitched up.

QUARRY FOREMAN WAS WORKING UNDERNEATH HIS OWN PICKUP. HAD PUT FRONT WHEELS UP ON RAMP. HE LOOSED DRIVE SHAFT AND PICKUP ROLLED OVER THE CHEST CAUSING BRUISES & ACUT ACROSS HIS FOREHEAD.

EE WAS DIRECTING HAUL TRUCKS TO DUMP. HE DECIDEDTO ROLL A FOZEN CHUNK OF DIRT INTO A HOLE & PULLED GROING DOING SO.

EE WAS DRIVING A HAUL TRUCK & FELT CHEST PAINS. WAS TAKEN TO HOSPITAL WITH A HEART ATTACK. HAD BYPASS SURGERY.

EMPLOYEE WAS HELPIN PUT PUG MILL BACK TOGETHER WAS FINE UNTIL WEST HOME THAT NIGHT AND BACK STARTED TO STIFFEN UP. LIFTING DURING DAY AND CAUSED LOWER BACK STRAIN.

AN EMPLOYEE FELL AND I BEAM ROLLED ON LEG (NO INJURY RESULTED) INJURED EMPLOYEE LIFTED THE BEAM AND STRAINED HIS BACK.

EXACT TIME CANNOT BE DETERMINED. EE STATED HE WAS PUTTING IN SCREEN DECK 2 OR 3 MOS BEFORE AND FELT PAIN IN NECK. HE DID NOT THINK IT WAS A PROBLEM AT THE TIME, BUT WHEN HE CONTINUED TO FEEL PAIN HE WENT TO A DR AND DISCOVERED HE HAD SLIPPED A DISK IN HIS NECK. AFTER TREATMENT THE PROBLEM WENT AWAY

EE WAS OPERATING PLANT CONTROL TOWER. A ROCK LODGED IN JAW & HE WAS USING A JACK HAMMER TO BREAKIT DOWN. FELT A STRAIN IN BACK FROM USING JACK HAMMER. AFTER 3 WEEKS OF WORKING WAS ADVISED BY D OCTOR TO TAKE A WEEK OFF TO REST BACK, RETURNED WITHOUT FURTHER PROBLEMS.

72"ELJAY CONE WAS BEING ADJUSTED. EMPLOYEE WAS ON CONE PLATFORM USING A WRENCH TO LOCK IN WEDGES ON CONE AS IT'S SPACING WAS TAKEN UP. FOREMAN SAID AT TIME OF ACCIDENT NO ACTION WAS TAKING PLA CE ON CONE. THE WRENCH, ACCORDING TO EMPLOYEE, JUMPED OUT OF SLOT AND STRUCK HIS UPPER RT LEG, CAUSING A BRUISE. EMPLOYEE WAS BROUGHT TO TOWN FOR BROKEN BONE, BUT LEG WAS BRUISED & HE RETURNE

EMPLOYEES WERE WORKING ON 72" CONE BOWEL. THE EMPLOYEE WHO WAS INJURED WAS STANDING INSIDE THE BOWL HOLDING A WRENCH IN PLACE ON A NUT HEAD WHILE OTHER EMPLOYEES WERE TIGHTENING DOWN BOLT OUTSIDE THE BOWL. INJURED MAN HAD HIS HAND ON BOWL. SOCKET ON AIR WRENCH SHATTERED AND A FRAGMENT STRUCK EMPLOYEE'S HAND.

PLANT WAS BEING STARTED UP. EE WAS STANDING ON CONE PLATFORM TO CHECK FEED AND CONE OPERATION AT START UP. AS ROCK WAS BEING FEED INTO CONE A ROCK -4 INCH CAME OUT OF BOWL OF CONE AND STRUCK E E ON TOP OF BOTH HANDS. CONTINUED TO WORK THAT DAY AND WENT TO DR AFTER WORK BECAUSE OF BRUISNG.

EMPLOYEE (THE DRILLIN GFOREMAN) WAS RAISING DRILL STEEL OUT OF HOLE. THE SUBSHAFT HOLDING BIT WOULD NOT LOCK INTO PLACE ON CARRIER. INSTEAD OF USING PROVIDED TOOL, EMPLOYEE TRIED TO HOLD UP LOCKING PALTES WITH HIS HAND AND WORK HYDRAULIC CONTROLS WITH OTHER HAND. WHEN HE DID SO LEFT FOREARM WAS PINCHED AND HE SUFFERED SLIGHT EDEMA AND SUPERVICIAL ABRASIONS. HAD ARM X-RAYED THAT

EMPLOYEE WAS HELPING TO TAKE OFF CUTTING EDGE ON ENDLOADER. BOLTS HAD BEEN REMOVED EXCEPT FOR ONE. WHEN EMPLOYEE TOOK IT OUT, METAL FELL 2 FEET AND STRUCK HIM ON RIGHT FOOT CAUSING CONTUSION.

EMPLOYEE, THE QUARRY FOREMAN, WAS CLIMBING DOWN FROM A CAT 769 HAUL TRUCK. HE SLIPPED ON THE STEPS COMING DOWN AND STRUCK RIGHT ELBOW ON GUARD RAIL AROUND THE CAB OF THE TRUCK. HE BRUISED ELB OW AND AN INFECTION GOT STARTED BY THE BONE AND SURGERY HAD TO BE DONE TO DRAIN THE INFECTION.

EE WAS WORKING WITH A SECOND EE TO TAKE THE PINS OUT OF THE JAW PLATE FOR REMOVAL. THEY WERE DRIVING THE PIN OUT WITH A MAUL AND METAL BAR. THE MAUL WENT OFF THE BAR AND STRUCK EE'S HAND AND S PLIT OPEN HIS INDEX FINGER. HE WAS TAKEN TO TOWNAND FINGER WAS STITCHED UP AND HE RETURNED TO WORK NEXT DAY.

NEW SCREEN WAS BEING PUT IN PLACE ALONG WITH NEW COVNEYORS. EMPLOYEE (THE PLANT FOREMAN) HAD CLIMBED UP ON CONVEYOR THAT HAD BEEN SET BY CRANE AND WHICH WAS ABOUT THREE FOOT OFF THE GROUND. HE WAS TAKING THE CABLES OFF OF CONVEYOR AND WHILE MOVING FROM ONE SIDE TO THE OTHER CAUGHT HIS FOOT BETWEEN THE BELT AND A ROLLER AND LOST HIS BALANCE. HE FELL THE THREE FOOT TO THE GROUND AND

ROCK HUNG UP HE WAS MOVING SMALLER ROCKS TO GET LARGE ROCK ROCK ROLLED OVER UT FINGER INDEX ON R HAND STITCHES

EE WAS WELDING ON FRAMEWORK OVERHEAD. WHILE DOING SO A PIECE OF SLAG GO INSIDE SLEEVE AND BURNED HIS ARM.

EMPLOYEE WAS REPLACING SCREEN DECK ON SCREENING PLANT USING A WRENCH. HAD REMOVED SEVERAL BOLTS AND FOUND ONE THAT WOULD NOT BREAK LOOSE. USED EXTRA FORCE AND LATER FELT A PAIN IN LOWER BACK.

EMPLOYEE WAS WELDING ON FRAMEWORK AROUND CONE CRUSHER. HAD USED A PIECE OF ANGLE IRON AS A MARKER AND LAID DOWN BETWEEN FRAMEWORK HE WAS ON AND A SECOND FRAMWORK. AFTER WORKING FOR A WHILE WEN T TO WORK ON OTHER FRAME. HE STEPPED ACROST AND PUT FOOT ON ANGLE IRON WHICH CAUSED HIM TO FALL ABOUT 9 FEET TO MUDDY GROUND.

EMPLOYEE WAS ADDING A SECTION OF STEEL TO I-R T4 DRILL. HE WAS HOLDING A SCREW IN CUP IN PLACE AS THE STEEL WAS MOVED INTO PLACE BY CAROUSEL. AS CAROUSEL SWUNG AROUND EMPLOYEE GOT ARM PINCHED BETWEEN FRAMEWORK AND CAROUSEL. YELLED TO OPERATOR AND HE BACKED OFF HYDRAULICS AND RELEASED ARM. EMPLOYEE GOT A BRUISED MUSCLE. THIS PIECE OF STEEL DID NOT FIT JUST RIGHT OR EMPLOYEE WOULD NO

EMPLOYEE WAS WORKING ON SETTING UP PLANT. HE WAS WORKING UNDER A FRAMEWORK ABOUT FIVE FOOT HIGH AND STOOD UP AND HIT HEAD CAUSING AN ABRASION ON THE TOP OF HIS HEAD.

WITH ANOTHER EMPL EMPL WAS MOVING A 55 GAL OIL DRUM INTO AN ENDLOADER BUCKET LOST HIS GRIP AND THE BARRELL FELL ON HIS L HAND CAUSING LACERATIONS ON MIDDLE TWO FINGERS

EMPLOYEE WAS HELPING A SECOND EMPLOYEE WHO WAS WELDING A METALFRAMEWORK. EMPLOYEE APPARENTLY WATCHED THE WELDING BEING DONE WITHOUT GLASSES AND THAT NIGHT HE FELT A BURNING IN HIS EYES CAUSED BY THE FLASH.

PLANT WAS RUNING A CONVEYOR STOPED EMP WENT TO ELECTRIC TRLR TO CHECK OUT SWITH AND FUSES ON LINE RUNNING TO CONVEYOR,WHILE WORKING ON THIS ELECT. BOX NEARBY BUT NOT PART OF CONVEYOR SYSTEM BLEW OUT AND SHOT FIRE ACROST AT EMP CAUSING 1ST AND 2ND DEG. BURNS ON HIS RIGHT HAND AND ARM AND ON RIGHT SIDE OF HIS FACE. BROUGHT TO ER ROOM AND BURNS WERE TAKEN CARE OF AND HE RTW N

EMPLOYEE WAS DOING A GRADATION TEST ON A RIPRAP PRODUCT MOVING LARGE PIECES OF ROCK WEIGHING OVER A HUNDRED POUNDS HE FELT A STRAIN IN HIS BACK WHILE MOVING ONE

ROCK WAS LODGED IN THE JAW AND EMPLOYEE ALONG WITH OTHERS WAS ATTEMPTING TO BREAK IT DOWN WITH A MAUL, ON ONE OF HIS SWINGS HE MISSED THE ROCK AND HIT HIMSELF IN THE LEFT LEG CAUSING BRUISING AND SWELLING BUT HE WAS BACK TO WORK AT THE NEXT WORK DAY.

A ROCK HAD LODGED IN JAW CRUSHER AND ALONG WITH 2 EMPLOYEES THE EMPLOYEE WAS MOVING SMALLER SHOT ROCK TO GET AT LODGED ROCK A ROCK ROLLED AND STRUCK LITTLE FINGER ON EMPLOYEES LEFT HAND CAUSIN G CUTS AND SWELLING AND HE WAS TAKEN TO HOSPITAL TO SEE IF FINGER WAS BROKEN WHICH IT WAS NOT

EMPLOYEE WAS HELPING A TRUCK DRIVER RELEASE HIS TAILGATE WHICH HAD MATERIAL PUSHED UP AGAINST IT WHEN HE RELEASED THE CHAIN ON THE RELEASE HANDLE THE TAILGATE POPPED OPEN AND THE HANDLE SWUNG BACK AND STRUCK THE EMPLOYEES LEFT HAND BREAKING A BLOOD VESSEL AND CAUSING SOME SOME SWELLING IN HIS HAND WHICH WENT DOWN OVERNIGHT

EMPL WAS WELDING ON CONVEYOR BELT AT STONE PLANT WHEN A PIECE OF METAL FLEW INTO HIS EYE EMPL WAS UNABLE TO REMOVE FROM EYE AND AFTER CONTINUED IRRITATION HE WENT TO DR FOR REMOVAL

EMPLOYEE WAS LI0TING A WOODEN BLOCK WITH ANOTHER EMPLOYEE, HE PICKED UP HIS END BEFORE OTHER EMPLOYEE DID AND STRAINED HIS LOWER BACK.

EMPLOYEE'S JOB IS TO CLEAN OUT ROCK UNDER CONVEYORS. THE JAW WAS PLUGGED WITH ROCK AND BELTS WERE STOPPED, BUT BEFORE THEY CAME TO A COMPLETE STOP EMPLOYEE WALKED UNDERNEATH AN OVERHEAD CONVEY OR AND A ROCK WAS ROLLING DOWN THE BELT AND BOUNCED OFF, FALLING ABOUT TEN FOOT AND STRUCK HIM ON THE HEAD.

EMPLOYEE WAS HELPING TO PUT A CUTTING EDGE ON AN ENDLOADER. WHILE DOING SO ONE SECTION OF THE CUTTING EDGE FELL ABOUT A FOOT AND LANDED ON HIS RIGHT FOOT, CAUSING SOME BRUISING. HE WAS TAKEN T O EMERGENCY ROOM TO CHECK FOR BROKEN BONES-NONE WERE FOUND.

EMPLOYEE WAS ST5NDING ON CONEVEYOR BELT CHANGING GRIZZLE BARS IN A RIPRAP DEEDER.THE FOREMAN WAS SHOWING A NEW EMPLOYEE HOW THE LECTRIC CONTROLS WORKED FOR THE RIPRAP PLANT AND THOUGHT THAT PO POWER TO THE PL5NT WAS SHUT OFF &BUTTON WAS PUSHED STARTING CONVEYOR BELT UP.EMPLOYEE LOST BALANCE AND FELL ABOUT TEN FEET TO THE GROUND.

EMPLOYEE WAS CL9ANING OUT FROM UNDER CONVEYOR BELTS. A ROCK FELL APPROX. 1K FEET AND STRUCK EMPLOYEE ON TOE ON LEFT FOOT CAUSING A CONTUSION.

EMPLOYEE RUNS T2WER THAT RUNS CRUSHING EQUIPMENT. A ROCK LODGED IN THE JAW AND AFTER STOPPING JAW THE EMPLOYEE ATTEMPTED TO MOVE SMALLER ROCKS OUT OF THE WAY SO HE COULD BREAK LODGED ROCK WIT H MAUL. HE CAU1HT LITTLE FINGER RIGHT HAND BETWEEN 2 ROCKS CAUSING A LACERATION AND FRACTURE OF THE FINGER.

EMPLOYE WAS USI3G A SOCKET WRENCH TO TIGHTEN NUTS ON THE CUTTING EDGE OF A 980 LOADER. HIS HANDS SLIPPED AND HE STUMBLED AND TWEISTED HIS RIGHT ANKLE. HE CHECKED THE ANKLE AT EMERGENCY ROOM TH AT NIGHT AND WA8 FOUND TO HAVE SPRAINED ANKLE. MISSED NO TIME.

A BELT HAD COME3OFF A CONVEYOR. EES PUT IT BACK ON. FOREMAN PASSED WORD THAT CONVEYOR WAS TO BE STARTED AGAIN. ONE EE KEEP HAND ON CONVEYOR BELT AFTER WARNING & WHEN BELT WAS STARTED HIS LEFT THUMB WAS CAUG2T BETWEEN ROLLER & BELT CAUSING MILD CONTUSION & ABRASION TO THE THUMB.

CREW WAS PUTTIN1 IN A NEW CONVEYOR BELT, FOREMAN AND EMPLOYEE WERE WATCHING THE MATERIAL FLOW, THE FOREMAN SIGNALED FOR THE BELT TO BE SHUT DOWN. BEFORE IT HAD STOPPED COMPLETELY THE EMPLOYEE PUT HIS HAND O3 THE BELT AND HAD IT PULLED INTO THE PULLY CAUSING MULTIPLE LACERATIONS ON HIS LEFT HAND AND BREAKING THE LITTLE FINGER.

CREW WAS PUTTIN1 UP A NEW CONVEYOR AND HAD WELDED IN PLACE TWO STELL POSTS TO SERVE AS LEGS FOR THE CONVEYOR. EMPLOYEE FORGOT THE POSTS WERE THERE AND WALKED INTO ONE OF THEM, CUTTING HIS FOR EHEAD. HE WAS 7AKEN TO THE EMPLOYEE ROOM OF THE LOCAL HOSPITAL HAD SIX STICHES PUT IN.

ROCK BECAME LOD1ED IN JAW AFTER PLANT WAS SHUT DOWN EMPL TOOK MAULS TO TRY AND BREAK UP ROCK.EMPL CLIMBING DOWN TO ROCK LOST FOOTING AND FELL SHORT DISTANCE ONTO BACKSIDE.WHILE FALLING LET GO OF MAUL HE CARR3ED AND IT HIT ON LITTLE FINGER OF RIGHT HAND BREAKING FINGER.

EMPLOYEE WAS HELPING TO CHANGE A 36" BELT ON A CONVEYOR, BELT JOB WAS COMPLETED AND EMPLOYEE TOLD TO MOVE AWAY FROM BELT BEFORE IT WAS STARTED. HE FAILED TO MOVE AWAY AND LITTLE FINGER ON RIGH T HAND WAS PINCHED BETWEEN BELT AND ROLLER.

EMPLOYEE WAS CH5NGING A BELT AND IT CAME OFF AND HIT A MOTOR AND IT FELL ON HIS FOOT.