Buscar en el registro

The employee was shoveling/cleaning up on the S4 conveyor platform. The employee made a bad step through the floor and while falling hung upper left arm on a sharp piece of metal causing a long cut that required medical treatment including stitches.

A large piece of metal had lodged in the cone crusher North while trying to remove the metal, the crusher turned and smashed the employee's thumb against the bowl.

Employee was cleaning spillage under jaw crusher discharge belt when came in contact with moving belt and pinned employee against belt and conveyor frame, causing injury to shoulder.

Employee was changing the pre-screen on a machine and slipped of a platform approximately 3 feet off the ground landing on left shoulder. Suspected rotator cuff injury.

driller got out of drill to perform work around drill boom, turned ankle on rock on floor causing him to fall. left work at end of shift and said had no injury on following day went to doctor and found had broken bones in foot

Employee was climbing onto D65 Dozer. There was mud on the tracks causing him to slip and fall injuring his shoulder.

The employee was working on an impact crusher internal parts, when removing the main curtain hanger left side came loose the right side broke landing on his hand. There was no way to see the broken side of the shaft holding up the curtain. The right side hanger should have held.

Employee was loosening bolts on an electric motor in order to tighten the V Belts, the ratchet & socket slipped and he mashed his thumb.

The employee was removing a hydraulic line on a hydraulic cylinder, when the pressure in the system hit him in the face hurting his eye. The hydraulic fluid knocked off his safety glasses and hard hat.

While Employee was climbing up the stairs on a volvo haul truck, he lost his footing and fell to the ground.

Employee's were cleaning up under Jaw Crusher, co-worker was throwing shovel full of muck out from under Jaw when his shovel struck the injured EE's hand causing a cut to 2 fingers.

Employee was working on replacing a hydraulic cylinder on an underground drill. While driving the pin in the cylinder mount, a piece of the pin hit him on the right leg.

He strained his back loading powder monkey with 50 lb bags of ANFO.

SHE WAS CLEANING OUT A HEADER IN THE MINE WHEN SHE DROPPED OFF INTO A BAD SPOT IN THE FLOOR WHICH THREW HER INTO THE SEAT ARM REST AND INJURED HER RIBS.

Walking downstairs from office to shop, employee hung his ring on a nail sticking out of the wall, cutting his finger.

While doing maintenance on an impact crusher, the ee got his foot stuck behind. the rotor, when the rotor came lose and started to turn it broke his foot.

Employee was cleaning up around the tail section of a conveyer when he tripped and fell over rocks on ground.

EE REACHED INTO A DRAWER AT THE JAW OPERATORS BUILDING & CUT HIS HAND ON A 2" BAND THAT WAS BEING STORED FOR OUR WATER HOSES.

WHILE MOVING A 55 GALLON DRUM OF OIL APPROX 6 INCHES TO A 2 WHEELED DOLLY, EE PULLED HIS LEFT SHOULDER.

EMPLOYEE WAS CLIMBING LADDER, LADDER SLIPPED, EMPLOYEE FELL.

THE EMPLOYEE WAS REPAIRING AN ELECTRIC BOX WITH A SCREWDRIVER. THE SCREWDRIVER SLIPPED AND HIT A HOT WIRE THAT ARCED AGAINST THE BOX BURNING HIS HAND.

WHILE DRILLING A BLAST HOLE THE DRILLER DROPPED A STEEL OUT OF THE CAROSEL. IN TRYING TO LIFT DRILL STEEL BACK INTO RACK THE DRILLER PULLED HIS BACK MUSCLE.

EE WAS RUNNING PLANT WHEN IT STOPPED SO HE HAD TO GET A CONV. GOING HE SHUT THE WHOLE PLANT DOWN AND STARTED TO WORK ON A CONV. TAILPULLEY WHEN HE WAS WALKING AWAY FROM IT . HIS HEAD ON A PIEC E OF ANGLE.

EE WAS CLEANING UP BY HAND AROUND PLANT, PITCHED A ROCK INTO A CHUTE, MISSED, TRIED TO CATCH ROCK, ROCK FELL ON LITTLE FINGER.

WAS PULLING GEAR OFF OF SHAFT ON POWER TAK OFF AND FINGER BECAME LODGED BETWEEN SHAFT & GEAR. THE BELT THAT DROVE GEAR HAD MORE TENSION ON IT THAN ANTICIPATED.

EE WAS WELDING INSIDE A TRANSFER CHUTE WHEN HE LOST HIS FOOTING AND SLID ABOUT 12", STIRKING HIS TESTICLES ON A METAL BRACKET.

A CONTRACTOR WAS CHIPPING A WELD WHEN A PIECE OF SLAG FLEW UNDER HIS SAFETY GLASSES AND HIT HIS EYE. HE DID NOT REPORT THE INJURY THAT DAY. HE MISSED HIS NEXT DAY AND REPORTED FOR WORK ON THE 2ND DAY AFTER THE ACCIDENT. THE EYE WAS CLEANED, NO PERMANENT DAMAGE.

INJURED WAS RUNNING A LOADER CLEANING FACES WHEN THE CUTTING EDGE CAME OFF. HE BENT OVER TO LOAD CUTTING EDGE INTO BUCKET AND PULLED BACK THE CUTTING EDGE WEIGHS ABOUT 65 LBS.

WHILE USING A PRY BAR ON A ROCK THAT WAS JAMMED IN A BELT TRANSFER POINT, THE BAR SLIPPED CAUSING THE EMPLOYEE TO SMASH HIS FINGER AGAINST A ROCK. HE BROKE THE TIP OF HIS LEFT RING FINGER .

JUMPING BATTERY OFF HE LOST BALANCE & FELL FROM TRUCK PLATFORM ON TO HIS BACK

MOVING OXY CAGE WITH BACKHOE & HE WAS STEADING THE LOAD WITH HIS HAND HIT A BUMP & THE DOOR CAME CLOSE ON IT

ADDING 40' PIECE OF PIPE ON LAKE BEHIND DREDGE. THE WRENCH THE EE WAS USING SLIPPED ON BOLT BEING TIGHTENED AND CAUSED BOAT TO SHIFT AND EMPLOYEE FELL INTO FLOOR OF BOAT. EMPLOYEE CAUGHT HIMSE LF ON HIS HANDS IN FLOOR OF BOAT.

EE WAS PULLING BEARING HOUSING OFF OF A FINISH SCREEN WHEN IT UNEXPECTEDLY CAME LOOSE AND FELL ON HIS CHEST.

EE WAS WELDING HUB ON 1840 CASE SKID STEER. ONE OF THE CHAIN LINKS CAUGHT ON FIRE. HE RAISED HIS WELDING HELMET TO CHECK AND A FLASH FIRE CAUGHT HIS FACE AND NECK CAUSING 2ND DEGREE BURNS.

EE WAS SHOVELING AROUND PLANT WHEN HE FELT A PULL IN HIS BACK.

MAN WAS INSTALLING DRAIN PIPE, WHILE TRYING TO LINE PIPE HIS FINGER SLIPPED, INTO THE CONNECTION. PIPE SLIPPED TOGETHER WITH FINGER IN THE CONNECTION.

EE WAS STANDING ON A 2' LADDER CHANGING AN OIL FILTER ON AN R-50 EUCLID. WHEN HE SHIFTED HIS WEIGHT THE LADDER CAME OUT FROM UNDER HIM CAUSING A FALL. THE EE'S SHOULDER STRUCK A BATTERY THAT W AS ON THE SHOP FLOOR.

CARRYING 60 LB I-BEAM THROUGH JAW FEEDER, SURFACE WER, SLIPPED AND FELL.

WHILE TIGHTENING DOWN TENSION ROD ON JAW CRUSHER, ROD BROKE AND HIT HIM IN THE LEFT SHIN. TOOK HIM TO EMERGENCY ROOM; NO IMPAIRMENT, ABLE TO RETURN BACK TO WORK.

REPAIRING P4 CONVEYOR BELT, EE STATES, IS WHEN HE THINKS HE HURT HIS BACK.

LIFTING A 44" X 74" PIECE OF 1/2" STEEL PLATE WITH A SHEEPDOG ATTACHED TO A HOIST. THE SHEEPDOG SLIPPED OFF THE METAL AND HIT EE IN THE BACK AND ON THE BACK OF HIS LEGS.

WAS LOADING TRUCKS, FROM INSIDE CONTROL BOOTH, EYE STARTED ITCHING, HE KEPT RUBBING EYE CONTINUED TO GET WORSE, USED EYE WASH DID NOT HELP WENT TO DR, EYE CLEANED, ANTIBIOTICS USED, EE RETURNE D TO WORK NEXT DAY.

EE WAS INSTALLING CONDUIT IN MINE ENTRANCE. A PIECE OF CONDUIT HIT A SIDE OF THE WALL IN THE MINE. A ROCK FELL HIT HIS ARM, CUTTING HIS RIGHT FOREARM AND REQUIRING STITCHES. EE WAS RELEASED B Y DR TO RETURN TO WORK THE NEXT DAY.

MAN SERVICING UNIT #509. HE WAS CHANGE TRASMISSION FILTERS. WRENCH SLIPPED OFF BOLT CUTTING FINGER BETWEEN 2ND KNUCKLE AND PALM. WE CLEANED CUT WITH ANTISEPTIC AND BANDAGED.

PUSHING SIDE OF BIN OUT WHICH WAS BENT FROM FALL, PORTABLE POWER JUMPED OUT AND HIT SAID EE ON ARM.

EE WAS SCALING LOOSE FROM CEILING ROCK ROLLED DOWN BOOM INTO EXCAVATOR, HIT EE ON LEFT KNEE

HAD MISFIRE OF SHOT ON PREVIOUS NIGHT. WAS RECONNECTING NONJAB CAPS AND LOOSE ROCK FELL FROM FACE. SHOT BEHIND WALL OF MISFIRED SHOT, FIRED AND CONTRIBUTED TO LOOSE ON FACE.

OPERATOR DROPPED DRINK AND WAS RETRIEVING IT WHEN VEERED TO LEFT AND STRUCK CONCRETE UNDERPASS RETAINING WALL.

WAS LIFTING ELECTRIC MOTOR WHEN CHAIN CAME LOOSE AND STRUCK HIM ON SHOULDER AND WRIST. ACCIDENT HAPPENED BECAUSE CHAIN WAS IMPROPERLY HOOKED.

EMPLOYEE WAS REPAIRING THE JAMMED, OVERHEAD DOORCHAIN WHEN HE SLIPPED AND FELL BACKWARDS, LANDING ON THE SHOP AIR COMPRESSOR INJURING HIS BACK.