Buscar en el registro

employee was replacing and old disconnect box. EE got cut by the edge of the box on EE's arm. EE went to get a tetanus shot for safety

A cover on a breakerbox fell onto employee's middle finger. Employee got a cut.

Employee was checking screens when EE fell and scraped arm on grading.

Employee was locking up weed eater and it fell on their hand

Operator was cleaning an elevator chute when the left hand, ring finger was caught between a bucket and the elevator chute frame resulting in a cut from the finger tip to the first knuckle on that finger.

Sprained knee

It was lightly raining and an employee slipped on the top of the steps and fell down 4 steps. While trying to catch self, employee twisted back.

The employee was using a knife to check the up and down motion of a sheave at the #2 booster pump. EE was spinning it by hand. The sheave hit the knife and cut the employee's right pointer finger.

An employee was tapping bolts into the 12" flange for the waste pump with the hammer in EE's right hand when the hammer slipped and EE hit left hand, fracturing EE's left middle finger.

Contractor was cutting a piece of tin with a grinder when a small piece of metal struck them in the eye.

Employee was assisting in the removal of the gear box from the #1 Sand Dryer. Two bolts that were holding the gear box in place broke, causing the gear box to fall onto the employee's leg and causing a left proximal fibula fracture.

A bucket line was being held up using a hoist and a crane. The hoist broke and struck employee on the arm.

A customer truck driver was rolling up the tarp when the customer fell through a wooden board on the trailer that was rotted.

Employee was bailing water out of a boat with a 3.5 gallon bucket. The employee twisted back causing a lumbosacral sprain.

There was an electrical fire at the variable frequency drive in the MCC room at #2 Wet Plant. EE began to extinguish the fire using a fire extinguisher. EE then ran to the main disconnect located at the transformer station to turn off the power. While running, ee stepped on uneven ground and injured knee.

There was an electrical fire at the variable frequency driver in the MCC room at the #2 Wet plant. While extinguishing the fire, ee inhaled the smoke and the extinguishing agent.

The employee was hand stacking 50 pound clay bag, and when ee turned to place a bag on the pallet, ee felt a pain in their back.

Employee was holding a driving pin to remove a shaft from a fan housing. Another employee was hammering the driving pin and struck the injured employee's finger with the hammer.

Raymond Roller Mill star feeder was blocked with large clay lumps. Employee shut the system down to remove the the blockage from the feeder. When he removed the lumps of clay causing the blockage, the feeder turned and rolled over his left hand causing severe lacerations to his ring and middle fingers.

Employee was moving a water hose and stepped on uneven packed sand. Pulled muscle in right calf.

Employee had been working outside in the heat all day. Approximately 3 hours after his shift was over and he had gone home, his wife observed that he was flushed and showing signs of heat stress. He was taken to an urgent care center where he was treated for dehydration.

Employee stepped off of the concrete slab with his left leg. He knee buckled, and he fell down.

Employee slipped and twisted his knee while stacking bags

Employee was lifting 50lb clay bags and felt a pop in his back.

Step off 6" concrete pad, twisted ankle.

Employee was cutting steel supports from a screening structure and came in contact with a hot piece of steel causing a burn to his upper left arm.

Employee was tightening a stainless steel banding strap which secures the float to the dredge pipeline. The strap slipped and the sharp edge of the strap lacerated the employee's thumb.

Employee of contractor was installing catwalk at a sand plant which is being rebuilt. He and his helper were attempting to lay a piece of catwalk in place and when he lifted his end to lay it on the support beam his helper pushed it into place before the employee moved his hand out of the way and his right hand was lacerated when pinned between the catwalk and support beam.

Employee stepped off the stacking platform onto the floor and lost his footing. In an effort to keep from falling, he grabbed the forklift which was parked nearby. He did keep from falling but he hurt his shoulder in the process.

Employee was assisting two other employees with the removal of a cleanout door on the discharge side of a 10" pump, in an attempt to unplug the line. They were not aware that there was a buildup of hot water and steam in the pipe behind the door. As he was removing the bolts, the door broke free and the sudden escape of steam and water burned the employee on the left forearm.

Maintenance workers were relocating the dredge pipeline and this employee was attempting to secure a lifting strap around the pipeline. He reached underwater to wrap the strap around the line and cut his right hand on a banding strap which holds the line to floats.

Employee was walking around a corner and hit his head on a low hanging brace

Employee was trying to locate a leak in the 8" vacuum line from the clay drum filters. When he ran his hand over the area of the pipe where he suspected the leak to be located, the vacuum sucked part of his left hand into a hole in the pipe. He subsequently pulled his hand out lacerating the middle finger of his left hand on the sharp edge of the rusty hole.

Employee was stepping onto the top of a hopper car to get clay sample and he hit his left shoulder on the handrail. He then lost his balance and grabbed the handrail with his left hand and felt a severe pain in his left shoulder.