Buscar en el registro

IW & coworker were installing a roller and IW pinky got caught underneath, causing a laceration and fracture.

IW pulled a tool tray out and strained EE's back.

IW approached a small crane that was beginning operations. EE failed to alert the operator of EE's whereabouts. EE then stood in a blind spot for the operator and as the outriggers were being lowered EE got EE's foot caught.

IW was mounting haul truck after break. EE was not paying attention, EE was looking at EE's phone. EE bumped EE's head on the overhang of the truck bed.

IW was performing maintenance; carrying a guard and EE pulled a groin muscle.

IW struck left little finger with hammer.

Slip while dismounting caught self straining side

IW was hosing under equipment and when IW stepped back to turn, twisted left knee.

IW was cutting out a bearing and hot slag went under their safety glasses and into their eye.

IW working on a tarp and little finger got caught between rope and shaft.

IW was operating a loader when IW struck a solid rock with the bucket, jolting IW forward.

Worker has no specific incident or occurrence, but EE believes the sore back is from doing daily job - driving a haul truck.

Worker thought digging bar was clear of two pipes, and began to lift and walk away with it. The bar got jarred and as EE pulled, the motion over extended EE's shoulder. Worker denied care at time of incident. EE worked at full capacity until EE requested and went for an initial evaluated on 11/23/22.

IW was dismounting equipment when EE lost EE's footing on the last step banging EE's right knee.

IW lost footing while dismounting equipment, fell backward hurting back and right hip. Received restrictions 8/8, following initial treatment on 8/5.

Injured worker was struck in the head when a drum dolly became dislodged.

Employee was putting roller in and was struggling to get the roller to stand up next to another roller and while doing so, the hand rolled into the roller and got pinched between the two rollers.

Lifting rock out of the cone crusher chute. It slid out and ripped skin and nail of right pinky finger.

Employee said that they were working down in the hole, there was a roll of plastic liner on a rack being. As they were rolling out the plastic liner, the plastic liner slid down the rack and crushed employee's left hand between the liner and the rack.

While operating an excavator a small rock became dislodged and flew through the open window of the cab striking employee in the face above left eye.

Entering haul truck 06-0034 turned to open door, hit head on ROP guard (height of door 62.5 inches).

Tightening up a hose that was leaking, standing between tire and step fender on loader #260068 foot slipped, fell backwards onto blacktop approx. 4 feet, injuring center left side of back.

Servicing 26-0073 from top step, right side rear step 35" from floor changing filters, foot slipped off dirt on step, employee fell to shop floor.

Putting a nut on a bolt while on a small ladder, slipped off ladder, fell approximately 2 feet and landed wrong on EE's foot, injuring ankle.

Digging out chute. Employee has been working regular job since June, was treating with therapy. Employee has not improved and is going for surgery Fri. 9-15-17. Employee will be off work following surgery.

Heavy rain

Climbing off screen equipment, fell on the ground (4ft approx.). Left ankle sprain, facial contusions.

Pain in right arm from elbow to wrist. Employee was treating with WorkNet doctors and Phila Hand Ctr. until surgery 1/20/14 and still working. Started missing work 1/20/14.

Lifting 12" x 6" steel beam that was 8' long into loader bucket

Changing rollers at the Secondary crusher area on the 2-A (S-3) conveyor. While removing old roller frame, twisted left shoulder, treated at WorkNet for shoulder injury from time of accident. Went for arthroscopic surgery 7-30-12, had been working up until now.

Employee said he was attempting to roll a rock off to the side of the haul road.

Employee was moving water hose from drive side of crusher to non drive side of crusher. Employee fell off crusher.

Electrician EE was trouble shooting motor starter he placed the meter leads on the load side of the breaker and an arc flash occurred.

Stepping off step ladder, missed bottom step.

Climbing ladder to haul truck #060090, slipped and fell to the ground.

It was cold, raining and damp, EE stepped on wet platform of his trailer. He slipped and fell, twisting ankle.

EE was cleaning out chute under D-1 scren behind primary crusher on top of D-2 conveyor.

Climbing onto truck #060076 to check the fluid levels before starting it for the day, while climbing up ladder he felt a twinge on his right shoulder upper arm.

EE was starting and checking fluid levels of the haul trucks for the start of the shift. While checking truck #06-0090, EE slipped of the ladder on the front of the truck and fell backwards.

Slipped off of a ladder fell a few feet ( 2 - 3)

Working on primary crusher he dropped his wire brush onto D4 conveyor. He climbed down to get the wire brush. As he climbed out and off the conveyor he went to jump over the railing and his right knee locked up & he could not bend it.

On 11-23-05 employee reached for truck door and banged finger on door. On 12-13 employee went to personal physician & was given a prescription. On 12-27-05 he went back to physician and was put out of work for six weeks to prevent further dust exposure and cure finger.

REPAIRING DRIVE SHAFT IN A 988 LOADER, STRAINED LOWER BACK.

BLOCK SLID OFF PALLET DUE TO ICE ON BLOCK WHICH HIT EE IN THE LEFT SHIN. HE WAS MANUALLY HANDLING BLOCKS ON PALLET ON FORKLIFT.

EMPLOYEE OPENED DOOR OF FRONT END LOADER TO TALKTO TRUCK DRIVER, FOREIGN BODY BLEW INTO LEFT EYE.

GETTING OUT OF TRUCK, EE STEPPED IN A RAIN WASHED DITCH AND TWISTED LEFT ANKLE.

REMOVING ELECTRICAL DRIVE MOTOR ON D3 SCREEN AT THE SECONDARY CRUSHER PLANT. BIG TOE ON RIGHT FOOT WAS HIT WHEN LIFTING EYE ON MOTOR BROKE DROPPING MOTOR.

EMPLOYEE WAS USING MIG WELDER TO BUILD UP BARS INSIDE PRIMARY CRUSHER. HE RAISED HIS WELDING SHIELD UP WITH SAFETY GLASSES ON UNDERNEATH. HE BENT OVER TO MEASURE THICKNESS OF THE BAR, SLAG IN THE WELD POPPED, WENT UNDER SAFETY GLASSES.

DRIVING FUEL TRUCK DOWN INTO THE QUARRY TO FUEL PUMPS, EMPLOYEE SAYS VEHICLE LOST BRAKES, RAN INTO BERM AND TURNED OVER ON DRIVER'S SIDE. INVESTIGATION FOLLOWING ACCIDENT REPORTED BRAKES O.K.

CRUSHER WELDER HIT EMPLOYEE'S RIGHT HAND WITH A SLEDGE HAMMER WHEN THEY WERE HITTING I BEAM TRYING TO FREE IT.