Buscar en el registro

Employee was walking & rolled EE's ankle

Employee was cleaning a catwalk with a crowbar, missed their spot and hit themselves in the cheek.

Employee said they were lifting a box of 8 gauge shells weighing 50 lbs. and felt pain in their lower back.

Employee was walking around screen conveyor tail pulley when EE tripped over the guard and hit EE's knee.

Employee was using a utility knife to cut a piece of 6" rubber skirt board.

Employee was cutting an old chute down in pieces and putting them on the ground when a sharp edge cut EE's finger.

Employee was carrying an acetylene tank when they felt a pulled muscle.

Employee removed the guard on the 30" stockpile conveyor snub roller. While it was running, EE put a crowbar in it to clean.

Employee was using a crowbar to open hatch in the tunnel when the bar slipped and employee hit elbow.

Tripped on a harness safety lanyard

Employee was loosening bolts on the mill when they lost their grip and hit their arm on a piece of metal.

Employee was hitting a coal hopper with a 3lbs lump hammer and hit/jammed their finger.

Employee was hitting slug wrench with hammer when the nut came loose the wrench hit EE's finger.

Swinging hammer to tighten the wedges on crusher.

Employee was cleaning up material at the finish plant. EE walked up to the shop and told the supervisor to send the maintenance down to help when the super said the EE said hurt knee. *The EE was denied a vacation day for Friday.

Employee was picking up a piece of 2x2x1/4" angle iron when EE dropped it on their finger.

Employee was walking when they tripped and fell, cutting their right palm.

Employee was walking when the wind blew dust in EE's right eye.

When turning down head nut with pinch bar in shop, strained left shoulder.

Employee was unplugging the crusher when a rock hit them in the left forearm.

Employee was adjusting a 425 Symonds crusher using a come-along adjusting bolts, was not loose. Employee "side loaded" come-along breaking connection to hook, causing chain to hit EE in EE's side/back.

Employee was cleaning a chute with a bar and pulled muscle in shoulder.

Employee was removing a trunnion cover from the front pier on #1 kiln when they turned and felt a pain in groin area.

Employee was discarding old scrap metal into a dumpster and hit pinky.

Employee was relining a chute when the "D" ring welded in the chute broke off dropping the steel on EE's left foot.

Employee was walking under #1 kiln by tunnel entrance when employee *said* employee slipped on ice. *NO ICE WAS FOUND!

Employee was wheeling brick in kiln when employee said employee felt a pain.

Employee was replacing guard on Portable Plant head pulley conveyor

On 11/26/18 EE was asked to help maintenance employee then said couldn't do it because EE hurt back on 11/21/18. This was at start-up.

Walking to EE's pickup truck, lunch time, twisted left ankle. Note, in employee parking lot.

Check kiln operations stepped on empty shell casing while adjusting air door.

Changing a screen.

Employee opened breach door on rear of #1 kiln. Walking down stairs, lost footing, missed step.

Employee said in the first 15 min of start of shift needed to move the gun and pulled something in lower back.

Employee was about to change drive belts on the screen and lost footing. Put left arm out and dislocated shoulder.

Operating a jack hammer. *Employee said they must have done this here because they don't work at home.

Employee was shoveling in #1 tunnel doing cleanup.

Installing a motor mount on the pony motor in the shop. Caught his middle finger in the hole on the mount.

While climbing #1 bucket elevator to grease on top, dust or stone got in left eye.

Walking from bathroom by the back door of #2 kiln on the west side stepped on rock or rut

Employee lost footing and fell

EE said he was moving the kiln gun away from the kiln after shooting a ring out and slipped off diamond plate and hurt his pinky.

Putting a conveyor belt splice in the 3/4 conveyor @ the finish plant.

A breaking switch located in the portable plant control room shorted out causing a flash where the breaker was turned on causing minor burn to employee's hand.

EE was climbing on loader to add engine oil to equipment when he said he pulled something in his hip.

EE was welding on #2 elevator when he started to weld got a shock.

Shoveling in #2 tunnel said he twisted knee

Working on rebuilding hydraulic cylinder. When tightening nut, wrench slipped off nut pinching right pinky finger on floor.

Employee was working on top of #2 Elev. when co-worker opened the breach door letting dust out in area where employee was working.