Buscar en el registro

DISMANTLING ELECTRICAL CABLE TRAY IN MILL ELECTRICAL ROOM. TWO MEN WERE STANDING ON SEPARATE LADDERS REMOVING ELECTRICAL CABLE TRAY. ELECTRICAL CABLE TRAY WAS NOT SECURED PRIOR TO REMOVAL CAUS ING IT TO FALL. THE ELECTRICAL CABLE FELL AGAINST ONE OF THE LADDERS, KNOCKING IT OUT FROM UNDERNEATH EE.

THE EE STATED THE HE CONDUCTED HIS PRESHIFT INSPECTION, FUELED, AND PROCEEDED TO THE LOADING AREA. HE STATED THAT AS HE THEN DESCENDED THE RAMP, HIS BRAKES DID NOT SLOW HIS SPEED. SEEING A STA LLED TRUCK AT THE FOOT OF THE RAMP BELOW HIM, HE DURECT THE TRUCK TO THE WALL TO HIS LEFT. AS THE LEFT TIRE ROLLED UP THE TOE OF THE HIGHWALL, THE TRUCK TURNED ONTO ITS SIDE ON THE HAULROAD.

EMPLOYEE WAS HELPING TO HOLD UP A JACKHAMMER DRIVING 2" BOLTS THROUGH THE SAE MILL LINER. HE HAD POSITIONED HIS RIGHT THUMB IN FRONT OF THE JACKHAMMER BOLT; WHEN THE HAMMERING BEGAN, THE BOLT GAVE WAY SUDDENLY CAUSING THE HAMMER STEEL TO ENTER THE BOLTHOLE AND CATCH HIS THUMB BETWEEN THE MACHINE AND THE MILL LINER. INJURY RESULTED IN FRACTURE TO TIP OF RIGHT THUMB; SUTURES OF NAIL

MILL OPERATIONS EMPLOYEES WERE REMOVING A LINE FROM A PUMP ON TOP OF TANK 5 IN THE CIL AREA WHEN A CLAMP ANOTHER EE WAS LOOSENING FELL AND STRUCK EE'S RIGHT THUMB. THE RESULT WAS A LACERATION REQUIRING (4) FOUR SUTURES.

EE AND THE CREW TEAM LEADER WERE ATTEMPTING TO POSITION A 4' 6X6 TIMBER UNDER THE DISCHARGE LINE OF A PORTABLE PUMP. THE TEAM LEADER PUSHED IT CAUSING IT TO PINCH EE'S FINGER BETWEEN THE TIMBE R AND A ROCK. WEATHER WAS WIND & RAIN.

EMPLOYEE OPENED THE LID OVER THE HYD OIL TANK TO ADD OIL. THE LID FELL CLOSED ON HIS LEFT HAND CAUSING CUTS REQUIRING SUTURES ON MIDDLE AND RING FINGER (2&3).

DRIVELINE GUARD SLIPPED FROM EMPLOYEES HANDS AS HE WAS REMOVING IT. THE GUARD HAD A SHARP METAL BURR AT A BOLT HOLE, WHICH CAUSED A LACERATION REQUIRING SUTURES. EE WAS NOT WEARING GLOVES.

EMPLOYEE STATED THAT HE WAS CLIBRATING AN AUTOMATIC WATER ADDITION VALVE. AS HE WAS ADJUSTING THE METER HE RESTED HIS LEFT HAND ON PIPE BESIDE THE VALVE. HE WAS UNAWARE OF THE CLOSE PROXIMITY OF HIS FINGER TO THE VALVE ACTUATOR AND AS THE COUPLING TURNED 90 DEGREES, HIS FINGER WAS PINCHED BETWEEN THE SUPPORT BARS AND THE COUPLING.

EMPLOYEE STATED THAT HE WAS USING A BALL PEEN HAMMER TO DRIVE A BALL STUD INTNO A STEERING CYLINDER WHEN A PIECE OF METAL CHIPPED OFF THE HAMMER CAUSING A PUNCTURE WOUND TO HIS ABDOMEN. EMPLO YEE RECEIVED 2 SUTURES.

ACCORDING TO WITNESS, EE WHO WAS ALSO OPERATING A HT 10(35 TON HAUL TRUCK), HE PULLED HIS TRUCK ALONG SIDE ANOTHER 35 TON HAUL TRUCK (HT15) TOGIVE IT A JUMP START BATTERY TO BATTERY. AFTER ST ARTING THE HT1 HE WENT TO THE FRONT OF THE TRUCK TO GET THE UMPR CABLES FROM EE WHO WAS MANNING HT15. HE PROCEEDED DOWN TO THE TOOL TRUCK TO PUT THE CABLES AWAY AND ON HIS RETURN NOTICED HT 1

EE STATED THAT AS HE WAS COMPLETING HIS PRE-SHIFT EQUIPMENT INSPECTION, HE SLIPPED AND FELL AS HE WAS CROSSING FROM THE ENGINE DECK TO THE CATWALK IN FRONT OF THE OPERATORS CAB. ACCORDING TO A WITNESS, HE FELL FEET FIRST TO THE BUMPER AND THEN TO THE GROUND.

EE STATED THAT HE HAD PLACED THE 48" PIPE WRENCH ON A PUMP IMPELLER SHAFT. A NYLON SLING WAS ATTACHED FROM THE WRENCH TO THE TAKE UP ON THE BOOM TRUCK TO PROVIDE MECHANICAL ADVANTAGE. THE EE H AD HIS RIGHT HAND ON THE WRENCH HANDLE, HOLDING IT IN POSITION UNTIL SET. THE SHAFT TURNED SUDDENLY AS TENSION WAS APPLIED, CATCHING THE TWO FINGERS BETWEEN THE HANDLE AND THE PUMP GUARD.

EMP STATED THAT WHILE ALIGNING THE RIM PARTS ONTO THE RIM, HE NOTICED HE HAD CUT HIS LEFT THUMB ON A BURR OF METAL ON THE SIDE RING. THE 3/4" LACERATION REQUIRED FIVE SUTURES.

EE STATES THAT HE WAS REMOVING A PIECE OF METAL FLOOR GRATING (3'X7') PANEL AND THE PANEL SLIPPED, CAUSING HIS FINGER TO WEDGE BETWEEN THE PIECE HE WAS MOVING AND ANOTHER STATIONARY PIECE.

EMPLOYEE WAS DRIVING AN 85 TON HAUL TRUCK DOWN HILL WHEN THE SEAT BOUNCED AND ROCKED FORWARD. UPON INVESTIGATION THE REAR SEAT MOUNTING TABS HAD BROKEN, ALLOWING THE SEAT TO HINGE ON THE FRONT TABS. WHEN THE EMPLOYEE BRACED HIMSELF TO PREVENT THE MOTION OF THE SEAT, HE FELT PAIN IN HIS LOWER BACK & LEFT LEG. THE EMPLOYEE RECENTLY RETURNED TO WORK AFTER AN OFF THE JOB INJURY OF BACK

EE HAD REMOVED A NUT FROM A U-BOLT SECURING A 12" DIAMETER PIPE TO A VERTICAL PIPE STAND. AS A COWORKER LOOSENED THE NUT ON THE OTHER SIDE OF THE U-BOLT, EE STOOD BY TO OBSERVE. AS THE NUT WAS LOOSENED, THE PIPE STAND SLID BACK SUDDENLY ANDSTRUCK THE FIRST MECHANIC IN THE MOUTH AND NOSE.

AFTER THE STRIP COLUMN PLUGGED UP, AND FOLLOWING SEVERAL ATTEMPTS TO CLEAR IT, THE EE REMOVED THE BOLTS TO THE ELBOW ABOVE THE FILTER TO GAIN ACCESS. AS THE LAST BOLT WAS REMOVED, BACKPRESSURE RIGHT SIDE, RESULTING IN 1ST AND 2ND DEGREE THERMAL AND CHEMICAL BURNS.

EE WAS PUTTING RUBBER BOOTS OVER HIS REGULAR BOOTS, AND FELT SOMETHING POP IN BACK.

NO INJURY OR ILLNESS.

KNOCKED TO THE GROUND BY HIGH WINDS AS A TORNADO PASSED NEAR THE NORTH PIT. THE EMPLOYEE WAS WALKING BETWEEN THE BLASTHOLE AND THE SHIFT SUPERVISOR'S PICK UP (APPROX. 30 FT.) THE WINDS FORCED HER DOWN ONTO HER BUTTOCKS AND DID NOT ALLOW HER TO STAND UNTIL IT PASSED. THE EMPLOYEE WAS EXAMINED BY A DR. IMMEDIATELY AFTER THE INCIDENT, BUT NO APPARENT TRAUMA WAS NOTED. EMPLOYEE WAS SUB

EMPLOYEE STATES THAT AS HE WAS USING A TOOL TO REMOVE A TUBE CAPE ON A SCREEN, HIS HAND SLIPPED AND STRUCK HIS MOUTH, FRACTURING HIS TOOTH.

ALLEGED THAT WHILE UNLOCKING GATE GATE FELL ON LEG

GRINDING RUBBER. GRINDER JUMPED AND CUT LEG ABOVE KNEE CAP.

INJURED CUTTING RUBBER. KNIFE SLIPPED SMALL CUT ON LEG.

EMPLOYEE STATED THAT HE LOST CONTROL OF THE HAUL TRUCK HE WAS OPERATING AND THE RIGHT SIDE OF THE TRUCK CLIMBED THE HIGHWALL. THE TRUCK FLIPPED OVER ONTO THE DRIVER'S SIDE, PINNING THE EMPLOYE E'S HAND BETWEEN THE GROUND AND THE DRIVER'S SIDE DOOR.

EMPLOYEE WAS CLIMBING DOWN THE LEFT FRONT LADDEROF A 777B. EMPLOYEE STATED THAT THE GROUND WAS LEVEL AND FREE OF GREASE-OIL-MUD-ETC. AND HE WASNOT PAYING ATTENTION TO HOW HE PLACED HIS FOOT AND CAUSED HIM TO STRAIN HIS RIGHT ANKLE.

EMPLOYEE STATED THAT AS SHE WAS ADJUSTING THE DRIVER'S SIDE WINDOW OF HER HAUL TRUCK, THE DOOR CLOSED, SMASHING HER RIGHT THUMB BETWEEN THE DOOR FRAME AND THE DOOR.

ON SEPT. 18 KRMC MILL TECH. REPORTED TO HIS SUPERVISOR THAT HE FELT PAIN IN HIS LOWER BACK AFTER SHOVELING CARBON FINES. ON OCT. 11 HE WAS SEEN BY A PHYSICIAN ON A FOLLOWUP VISIT. @ THAT TIM E PHYSICIAN PRESCRIBED PHYSICAL THERAPY.

EMPLOYEE STATED THAT WHILE REMOVING THE BOLTS FROM THE TRACK MASTE RLINK THAT WHEN HE REMOVED THE LAST BOLT HTE LINK SEPERATED AND PULLED THE AIR WRENCH OUT OF HIS HAND AS THE AIR HOSE PASSED THROUGH HS HAND THE CLAMP USED TO HOLD THE COUPLING TO THE HOSE CUT HIS HAND.

EMPLOYEE STATED THAT WHILE REMOVING BUCKET TOOTH FROM 992 C LOADER. A PIECE OF METAL FLEW OFF THE TOOTH WHEN HE STRUCK IT WITH HIS 4 LB. HAMMER. THE PIECE OF METAL ENTER ON THE R.H. SIDE OF HI S ABDOMEN.

EMPLOYEE ALLEGES THAT AS HE STEPPED DOWN OFF THE BOTTOM RUNG OF A LADDER WHILE DISMOUNTING A 980-A CATERPILLAR FRONT END LOADER HE TWISTED HISRT ANKLE EXTENT OF THE INJURY IS STILL BEING INVES TIGATED

EMPLOYEE WAS OPERATING A HDPE FUSION MACHINE. THE DEVICE UNEXPECTEDLY LIFTED UP. THE EMPLOYEE, IN REFLEX, PUT HIS HAND UP AND MACHINE HANDLE CAUGHT THE FINGERNAIL ON EMPLOYEES LEFT LITTLE FING ER. DOCTOR REMOVED FINGERNAIL & PUT 5 STITCHES.

EMPLOYEE STATED THAT WHILE PRYING THE LOADER LIFT CYLINDER OUT THE PRY BAR SLIPPED AND PINCHED HIS FINGER BETWEEN THE PRY BAR AND THE LOADER FRAME.

FORKLIFT ROLLED FORWARD PUSHING EMPLOYEE OVER BERM AT TOP OF OPEN PIT MINE. EMPLOYEE FELL TO HIS DEATH.

REFER TO ATTACHMENT. Y

EMPLOYEE STATED THAT HE WAS IN THE PROCESS OF CHANGING A DRILL BIT ON DL01 WHEN HE CAUGHT HIS FINGER IN BETWEEN THE HYDRAULIC WRENCH & THE DRILL DECK THE EMPLOYEE SUSTAINED A SLIGHT FX ON THE TIP OF THE PHALLANGE OF THE LH RING FINGER

THE EMPLOYEE STATED THAT WHILE IN THE PROCESS OF CUTTING RETAINING BANDS ON A PALLET OF SAG MILL LINERS, A LINER SHIFTED ON THE PALLET WHEN HE CUT THE FIRST BAND. CONTRARY TO COMPANY PROCEDURE S AND TRAINING, THE EMPLOYEE HAD PLACED HIMSELF IN A PINCH POINT POSITION BETWEEN THE LOAD OF LINERS AND A HANDRAIL. WHEN THE LINERS SHIFTED, THE EMPLOYEE'S LEG WAS PINNED BETWEEN THE LINER A

TIGHTENING BOLT ON DREDGE COUPLING, WRENCH SLIPPED, FACE HOT BASE OF DREDGE CAR. THE FACE OF I.NAME HOT A PIECE OF ANGLE IRON ON THE CAB CAUSING A LACERATION BELOW THE RIGHT EYE. THE LACERATIO N REQUIRED FIVE STITCHES. A RATCHET AND SOCKET OF THE CORRECT WERE BEING USED. THE ANGLE IRON WAS APPROX. FROM HIS FACE BEFORE HE SLIPPED.

EMPL ACCESSING OPERATORS CAB OF DRILTECK ,FOOT SLIPPED OFF LOWER STEP AND RIGHT KNEE MADE CONTACT WITH UPPER STEP.

EE WAS REMOVING BENT HANDRAIL FROM EQUPMENT FENDER WAS IN PROCESS OF TERNING AROUND TO CLIMB DOWN LADDER WHEN HIS RIGHT FOOT SLIPPED EE KEPT BAALNCE EENOUGH WITH HIS ARMS TO LAND FLAT FOOTED O NTO FLOOR INSTEAD OF A POINT LOADED FALL ON ANY PART OF BODY X RAYS INDICATED SMALL FRACTURE OF A BONE IN BOTTOM OF RIGHT LEG AND OR UPPER PART OF RIGHT ANKLE.

PROCESS OF CHANGING WORN TIPS ON 992 LOADER BUCKET. THE EMPLOYEE WAS TAPPING ON FRONT OF TIP TO LINE UP RETAINING PIN HOLE. A SMALL CHIP OF METAL FLEW INTO INSIDE SKIN OF LEFT ARM BETWEEN WRIS T & ELBOW. SMALL BLEEDING CUT WAS VISIBLE ON ARM APPROX. 1/2 INCH JOY.

REMOVING A 3" GATE VALVE THE VALVE FELL AND MASHED EMPL INDEX AND MIDDLE FINGERS OF RIGHT HAND.

WHILE IN THE PROCESS OF CHANGING THE DRILL BIT ON DRILL DL-01. THE EMPLOYEE WAS REMOVING A NEW BIT FROM THE BIT RACK. AS HE BEGAN TO REMOVE THE BIT FROM THE RACK, THE BIT SLIPPED OUT OF HIS HANDS AND SMASHED HIS RING FIGNER. RIGHT HAND BETWEENT HE BIT AND THE BIT RACK.

74339NG WIRE TWISTED BACK INJ IT

ON 16 JUNE 92 AT 1535, EE AT THE TAILINGS GUARD SHACK WAS STANDING BY THE RADAR WHEN A GUST OF WIND CAME UP, BLOSING THE WINDOW OFF ITS TRACK. HE THREW UP HIS HAND TO PROTECT HIMSELF CUTTING H IMSELF ON SEVERAL PLACES OF HIS BODY.

THE EE STATED THAT HE ALONG WITH OTHER FLUOR A DNIEL EE WERE REMOVING THE CONCAVE PANELS FROM CR01. THE ROCK BREAKER WAS BEING USED TO SHAKE OR LOOSEN THE PANELS THE ROCKBREAKER BIT SLIPPED FR OM THE SIDE OF THE PANEL. THE HOUSING OF RB01 HIT THE EDGE OF ONE OF THE PANELS CAUSING IT TO CHIP AND SEND A PIECE FLYING 6-8 FT WHERE IT STRUCK THE EE ON THE SIDE OF THE FACE HITTING HIS GL

EMPL CLEARING A PLUGGED FEED CHUTE WITH A JACKHAMMER. DROVE THROUGH PLUGGED MATERIAL,JACKHAMMER DROPPED 18" AND CAUGHT HAND BETWEEN THE JACKHAMMER AND THE FRONT OF THE FEEDER.

USING TORQUE WRENCH OTHER EMP GRABBED IT PINCHED HIS FINGER

EMPLOYEE STATED THAT WHILE HE WAS OPENING UP A CARBOARD BOX, THE EMPLOYEE WAS CUTTING TOWARD HIS BODY. THE KNIFE CUT THROUGH THE BOX AND CUT INTO THE EMPLOYEE'S HAND BETWEEN THE THUMB AND FORE FINGER ON THE LEFT HAND.

EMPL REACHING INTO GANG BOX. TOP OF WELDING ROD CAN HAD BEEN OPENED ON 3 SIDES AND PRYED BACK. EMPL REACHING IN ,CAN FELL OVER AND CUT THE BACK OF RIGHT HAND. EMPL ESCORTED TO FIRST AID/SECUR ITY OFFICE WHERE FIRST AID WAS ADMINISTERED.THEN TRANSPORTED TO DR WHERE 7 SUTURES WERE APPLIED. THEN RELEASED FOR WORK.