Buscar en el registro

Injured was cleaning out under some conveyor belts using a water hose when water deflected onto injured's face an into right eye. Injured was wearing safety glasses at the time. Injured went to Dr. on 10/19/21, diagnosed with a corneal abrasion.

Employee was walking on a catwalk when they slipped and grabbed onto the handrail for support. In doing so, a pain was felt in the shoulder. Injured went to doctor on 10/7/21 and was taken off work.

On 8/18/21 employee complained of shoulder pain from driving haul truck. Employee received steroid injection and physical therapy.

Injured was operating an angle grinder cutting a belt roller bracket when the grinder slipped and contacted the right thigh. Injury required stitches to close.

Injured was using a sledge hammer to loosen wear parts on a VSI rotor. While striking a cast bar, a piece of metal separated from the bar and entered into the injured's abdomen. Injured went to urgent care and received 2 stitches.

Employee stated had completed setting a pump. When EE turned to step away, EE struck forehead on the fork of the Telehandler.

Employee stated EE was operating a skid steer with an extended rake in the bucket, when the rake fell out EE ran over the rake causing the skid steer to bounce.

Employee stated EE was removing bolts from a cone crusher with a 1 inch impact when EE mistakenly put the impact on a separation bolt. When EE initiated the impact wrench it pinched EE's finger between the frame and the impact wrench.

Employee was stepping from the cab to the track of the excavator and rolled an ankle.

Employee stated was climbing up the steps on a haul truck when employee lost balance and fell.

The employee stated EE was using a hand drill to drill a hole in EE's toolbox when the bit broke. The broken bit struck EE's safety glasses and then EE's eye.

Employee stated EE was climbing into a screen deck to replace a screen when EE cut hand on a sharp rock.

Employee stated was installing a V belt, rolled finger between the sleeve and the v belt.

Employee was grinding on a finishing screen, eyes were irritated the next day, went to the doctor and had small pieces of steel in eye.

Employee stated ee was cleaning the concrete pad with a hose when ee stepped off the pad and strained knee.

Employee stated was cutting a rubber spacer with a utility knife when EE slipped and cut hand.

Technician was installing a rear A-frame for a 745C Cat haul truck, utilizing their service truck hoist and synthetic slings. While maneuvering the A-frame with the hoist, the A-frame shifted, pinching the technicians finger between the haul truck frame, and the A-frame being moved.

Employee stated was using a wrench to loosen bolts on a flange when the employee slipped and cut finger on a bolt head.

Employee stated was using a razor knife to cut piece of belting and cut leg with the knife.

Employee stated employee was walking towards a water pump to refuel it, while walking down the hill employee slipped and twisted employee's ankle.

Employee was troubleshooting a flow problem on the belt press. When EE pulled a hose off, the fluid sprayed EE in the face. Employee states EE knocked safety glasses off when the fluid startled EE.

Driving haul truck with arm resting on arm rest. Truck bounced, jarred shoulder.

The employee was running to turn on computer screen for the slurry and rolled their ankle.

Employee was operating a wheel loader, hit hole causing the seat to bottom out and jarred back. Employee went to doctor and restricted duty began on Aug 9.

The employee was performing maintenance at the jaw with a 24 inch crescent wrench and felt burning sensation in left bicep.

The employee was replacing teeth on a loader bucket when a small sliver of steel from the tooth struck the employee in the stomach.

The employee was changing a screen and struck EE's elbow on a beam.

Employee stated EE grabbed the handle of a tool being worked on by another employee and burned EE's hand, unaware the handle was hot.

The employee was using a bar to move a tail piece, tail piece slipped and fell on his foot.

The employee was changing a screen when he turned and felt a pain in his back.

The employee was working on the belt press checking a water line, when he inadvertently pulled the line loose causing water to splash in his eye. No injury, antibiotic was prescribed as preventive care.

The employee stated his eye started hurting following his shift at work. Went to the doctor who indicated it is possible he got sand under his contact lense.

The employee stepped off of a trailer and rolled his ankle.

The employee was exiting haul truck, her ankle gave out causing her to fall. Employee sought medical treatment after she was laid off and documentation to the extent of treatment was provided to the employer on January 20, 2015.

The employee was walking, stopped, turned and felt pain in his knee.

The Employee was assisting a welder when a piece of slag went behind his safety glasses and into his eye.

The employee was shoveling sand and struck his elbow on a steel beam. Injury was on 10-3-14 and physical therapy was prescribed on 10-13-14 making it reportable.

The employee stepped off of a concrete footing and twisted his ankle.

While an IMTR employee was unloading a drill steel from a delivery truck, the forks of the lull hung up on a cross member, when it released it pushed the drill steel onto the Fred Weber Inc. truck driver's foot.

Employee was removing a pin from a hydraulic cylinder when the cylinder fell on his thumb.

The employee was disassembling a take up, when a roller fell on his foot above the steel toe.

The employee was using a utility knife to cut a piece of belt, slipped and cut his finger.

The employee finished fueling a piece of equipment and was walking beside it to get back in it when he stepped on a rock which caused him to roll his right ankle.

The employee was climbing onto a trackhoe, slipped bumping his left elbow.

The employee reported eye irritation the day after working in the shop where welding was taken place.

Employee was using an air arc welder to remove a cone liner when a flash occurred resulting in burns to his face and neck.

The employee was shoveling and experienced groin pain. It was initially diagnosed as a personal health condition. A medical specialist later determined that the condition may have been caused by heavy lifting or straining.

Truck backing struck drill steel that was extending from a parked truck causing the drill steel to strike the employee.

Employee was walking near the de-energized crushing plant, a truck was going by and a rock struck him on the lip causing a laceration.

Employee was operating a 988 loader with the air conditioning on when blowing dust inside the cab caused an irritation in his left eye.