Buscar en el registro

The employee was fabricating a pump stand. EE moved a 4"x57" piece of channel. It slid off the support at one end & the other end pinched EE's finger on another channel. EE was wearing gloves and inspected their right index finger. It required 3 stitches.

Typical spring thaw conditions with muddy, soft, uneven ground. Stepped from a ladder and sprained EE's left knee. Worked on it and reported it to management after shift.

Miner was assisting in wash plant repairs & assembly. While installing parts on the plant, right middle finger was pinched, creating a blood blister under the nail.

Employee violated policy and attempted to clear a feed opening from the top when he was engulfed by sand and pulled through the feeder. Damage was loss of consciousness and bruises.

While placing a large wear plate in the jaw hopper, EE was using a pry bar to position the plate for attachment. The plate slipped on the bar, slapping the bar against the hopper. EE's hands were on the bar and his middle finger on his left hand got pinched between the bar and the hopper

While performing maintenance, employee stepped down off of the tail frame of the secondary cone supply conveyor. Employee lost his grip on the handrail and fell approximatly 30" on to the edge of a concrete block, fracturing his left hip.

EMPLOYEE WERE REMOVING A FLYWHEEL FROM THE SIDE OD A WASH SCREEN. A "T" BAR WEIGHING APPROX 10 LBS WAS USED A SPACER TO JACK THE FLYWHEEL OUT. WHEN THE FLYWHEEL CAME LOOSE THE BAR FELL APPROX (3) THREE FEET STRIKING EMPLOYEE'S RIGHT INSTEP OF HIS RIGHT FOOT.

OTHER EMPLOYEE HAD ATTEMPTED TO LOAD SOME SCRAP IRON AT VERELY GRAVEL WHEN HE RELIZED THE PIECES WERE TO HEAVY FOR THEM TO LOAD. HE SENT EE UP TO ASK OTHER EMPLOYEE IF HE WOULD COME AND HELP T HEM. AFTER OTHER HAD LOADED 2 OR 3 PIECES, HE ATTEMPTED TO LOAD ANOTHER WHEN IT WAS DTERMINED THE PIECE WAS TOO HEAVY FOR HIS TRUCK, SO OTHER PUT IT BACK AND OTHER POINTED TO ANOTHER PIECE. T

A MOBILE CRANE WAS BEING USED TO LOAD SALVAGE STEEL. IT WAS BOOMED ABOVE THE ADJACENT 7200 VOLT POWER LINES. THE VICTIM WAS GOING TO ATTACH THE LOAD LINE HOOK TO A PIECE OF SALVAGE STEEL THAT HAD BEEN CHAINED WHEN THE LOAD LINE CONTACTED ONE OF THE OVERHEAD ELECTRICAL CONDUCTORS, FATALLY ELECTRICUTING THE VICTIM AND SHOCKING HIS HELPER.

EMPLOYEE WAS PULLING ON RUBBER BUNGIE CORD TO TIE DOOR OPEN ON LOADER WHEN IT BROKE & HIT HIM IN THE EYE WITH A PIECE OF THE RUBBER FROM THE CORD

EMPLOYEE WAS TRAVELING DOWN HAUL ROAD HILL AND LOST CONTROL OF UNIT, FLIPPING UNIT OVER ON ITS SIDE.

EMPL WAS TAKING BEARING OFF ROLL FEED CONVEYER ON TWIN APACHE CRUSHER & PIECE OF STEEL CHIPPED OFF & HIT HIM IN RIGHT ARM IN MUSCLE BY SHOULDER. HE WAS ABLE TO PICK IT OUT BUT WENT FOR XRAYS T O MAKE SURE IT WAS ALL OUT. NONE WAS LEFT IN HE MISSED NO WORK.

WHILE SETTING JAW CRUSHER BACK ON FRAME AND PULLING IT INTO PLACE WITH COME ALONG TI MOVED. HIS HAND WAS IN WRONG PLACE AND GOT CAUGHT BETWEEN TWO PIECES OF STEEL PINCHING HIS SMALL FINGER ON RIGHT HAND.

EMPLOYEE WAS CARRYING PIECE OF 8" CHANNEL INTO WELD SHOP AND HURT HIS BACK.

EMPL WAS SHUTTING DOWN THE CRUSHER AFTER WHICH HE TURNED AND GOT HIS L HAND ON THE FAN GUARD THERE WAS A PART MISSING ON THE GUARD WHICH RESULTED IN THE CUTTING OF THE 1ST AND 2ND AND THE TIP OF THE 3RD FINGER ON HIS L HAND

WELDING ON 988B BUCKET, PIECE OF MATTER FLEW INTO EYE.

REPAIRING PUTTING FLASHINGD ON SHAKER UNDER ROLL CRUSHER WHEN FINISHED CLIMBING OUT HIT LEFT ELBOW WHERE ADJUSTMENT SPRINGS EXIST.

EMPLOYEE WAS TAPPING A LARGE BEARING INTO HOUSING OF HEWITT ROBBINS SCREEN AND A PICE OF METAL BROKE OFF AND HIT HIM IN THE LEFT FOREARM.

EMPLOYEE WENT OVER TO MOVE SURGE PILE STACKER AND WHILE HE WAS OPERATING BUTTON TO MOVE IT A ROCK CAME OFF THE BELT AND STRUCK HIM IN THE MOUTH (UPPER LIP & NOSE).

EMPLOYEE WAS HOLDING PIECE OF STEEL UP IN PLACE FOR HIM TO WELD IN PLACE. RECIEVED WELDER BURN ON EYES.

HE WAS GETTING OFF 475 TO HELP FELLOW EMPLOYEE & STEPPED ON ROCK BELOW LADDER OF MACHINE THEREBY TWISTING HIS RT.ANKLE DECLINED GOING TO DOC.SAID HE WULD GO TO HIS OWN DOC.

WAS TIGHTENING BEARING CAP W/SLUG WRENCH AND SLEDGE HAMMER WHILE HITTING SLUG WRENCH W/ THE SLEDGE HAMMER THE SLEDGE HAMMER DEFLECTED OFF OF THE SLUG WRENCH AND HIT THE EMPLOYEE'S KNEE

I.NAME ON CATWA5K BY CONE,CHECKING ON CONE FILLING UP WITH ROCK.A ROCK BOUNCED OUT OF CHUTE AND HIT RIGHT HAND RESTING ON GUARD AROUND THE CHUTE.MIDDLE FINGER OF RIGHT HAND WAS PARTIALLY CRUSH

HE TRIPPED ON R9BARB AND CUT HAND. HE NEEDED THREE STITCHES.

AN OPERATOR REM2VING WELDING HOOD AT THE SAME TIME TURNED AND GOT UP, THRERBY RUNNING INTO ANOTHER OPERATORS WELDING ROD. HE RECEIVED A FIRST DEGREE BURN ON HIS EYE.

WORKER HIT HIS 0INGER ON AN ANGLE IRON WHILE CLEANING HOPPER