Buscar en el registro

EMPLOYEE STUCK VOLTAGE METER LEADS INTO BREAKER BOX. HE HAD METER ON WRONG SETTING, WHICH CAUSED A FLASH (ELECTRICAL ARC).

EE WAS HOLDING AN ANGLE IRON WHILE SOMEONE ELSE CUT THE OPPOSITE END LOOSE. THE PIECE OF THE ANGLE IRON CAME LOOSE AND FELL STRIKING HIM, RESULTING IN A FRICTION BURN TO HIS ARM AND A SPRAINED ELBOW.

EMPLOYEE WAS WORKING IN SHOP, REBUILDING A TRANSIMSSION. HE PICKED UP A BOX WHICH WAS 2 FEET OFF THE GROUND, TURNED AROUND, AND FELT A PAIN IN HIS BACK.

EMPL WAS SHOVELING COAL ONTO BELT WHILE CLEANING BOTTOM PLANT FLOOR. AS HE MADE SWINGING MOTION WITH SHOVEL HE FELT PULL IN BACK. EMPL WORKED REST OF DAY.

HE WAS LIFTING A DRILL STEEL SUB, WHICH WEIGHS APPROX. 150 LBS, FROM THE DRILL ROD TO DRILL DESK. HE FELT PAIN ACROSS THE UPPER PART OF HIS BACK.

EE WAS CLEANING THE PLANT WHEN HE STEPPED THROUGH A PIECE OF GRATING WHICH HAD BEEN MOVED TO ONE SIDE OF A SUMP AREA, CAUSING THE EMPLOYEE TO STRIKE HIS LEG AGAINST THE GRATING.

EMPLOYEE WAS PRUING A RAIL CAR OPEN WITH APRY BAR WHEN THE PRY BAR SLIPPED IT CAUSED THE EMPLOYEE TO STRAIN HIS ABCK.

AS HE PREPARED 9MPLOYEE WAS DOING MAINTGENANCE WORK UNDERNEATH GRADER AS HE PREPARED TO COME OUT FROM UNDER THE GRADER HE STRUCK HIS HEAD ON THE GRADER DOOR

EMPLOYEE WAS OP9RATING GARDNER DENVER DRILL AFTER DRILLING THE SHOT AREA HE ATTEMPTED TO MOVE THE DRILL FROM THE BENCH AREA HE FAILED TO CHECK THE DRILL BENCH ROAD AND DROVE THE DRILL OVER THE LEFT SIDE OF T2E ROAD RESULTING IN THE DRILL BEING OVERTURNED AND EMPLOYEE TO BE THROWN FROM THE EQUIPMENT

EMPLOYEE WAS US3NG A 3 LB BALL PIN HAMMER TO DRIVE A TOP ROLLER OF THE TRACK SYSTEM ON THE DOZER. A PIECE OF METAL BROKE ON IMPACT AND BECAME EMBEDDED IN THE EMPLOYEE S SIDE.

UNPLANNED IGNIT3ON OR EXPLOSION OF BLASTING AGENT OCCURRED DURING LIGHTNING STORM INVOLVING 50 HOLES AND 75-100 LB PER HOLE OF EXPLOSIVES.ALL MEN HAD BEEN REMOVED FROM SHOT AREA HOWEVER WHEN H THEY RETURNED 7O WORKING AREA FOUND SHOT HAD BEEN DETONATED.NO ONE SAW OR HEARD SHOT AND NO INJURIES INVOLVED.THIS SITUATIO DISCUSSED WITH INSPECTOR AND BLASTING CREW DURING REGULAR INSPECTIO

EMPLOYEE WAS PR9PARING TO LIFT COAL SAMPLES INTO CRUSHER, AS HE BEGAN TO LIFT BAG, HE FELT A PULL IN LOWER BACK.

EMPLOYEE WAS AT7EMPTING TO LOAD & WIRE A FRESHLY DRILLED BENCH. WHILE ATTEMPTING TO LOAD A HOLE NEAR THE EDGE OF HIS WELL. EMPLOYEE SLIPPED OVER THE BANK.

EMPLOYEE WAS US3NG A HAND GRINDER TO GRIND EXCESSIVE SLAG FROM A JUST FINISHED WELDING JOB PIECE OF METAL SLIPPED CAUSING EMPLOYEE TO LOOSE CONTROL OF THE GRINDER THE GRINDER BLADE THEN KICKED BACK ON EMPLOYE9S HAND & WRIST

EMPLOYEE WAS SHOVELING COAL ON TOP OF RAILROAD CAR WHICH WAS BEING LOADED BY A CONVEYOR BELT EMPLOYEE JUMPED FROM ONE CAR TO THE OTHER STRIKING HEAD ON FRAME OF CONVEYOR BELT

HE WAS CLEANING BETWEEN BELT ROLLS AND GET HIS RING FINGER BETWEEN ROLL AND BELT AND HIS RING FINGER NAIL WAS MASHED

MOVING A MOTOR AND SPEEDREDUCER TO STACK FLOOR AND LEFT RING FINGER WAS MASHED BETWEEN MOVING MOTOR AND ONE THAT WAS STACKED.

EMPLOYEE WAS CUTTING METAL NEAR ANOTHER EMPLOYEE WHO WAS WELDING AND RECEIVED FLASH BURNS TO EYES WHEN AN ARC WAS STRUCK

HE WAS PRYING ON A CHAIN HOOK ON CORNER OF A RAILROAD CAR. BAR SLIPPED AND STRUCK ON INSIDE OF LEFT LEG.