Buscar en el registro

Area is in old works.

Bolting top and drawrock fell hitting his hand.

Between #1 entry into 2 left. Hill seam dropped out.

The fall is located 20' inby survey station #218 in the #3 entry 4 crosscuts outby the section loading point of the 001 MMU. The fall is approx 120' wide X 20' wide X 4'-5' in thickness.

Roof fall - 14 breaks inside at #6 entry #2 intake seal.

Fire started in cab of loader. No one around it.

Underground intersection at break 13 above #4 head drive about 3 1/2 ft. high, about 19 ft. wide, approx. 50 ft. long.

Turning into #3 entry from #2 cut too close, caught arm between rib & buggie.

Changing a foot shaft and twisted knee.

Bent over to get dust box sealed, drawrock fell hitting him in the lower back.

Glove caught on steel and twisted mashing hand in top.

Cutting belt for skirt on tail piece, box knife slipped cutting left thumb.

Shoveling and got a pain in left shoulder.

Working on miner-hit right thumb with hammer mashing it.

ON THE ROOF BOLTER, EMPLOYEE SWUNG POT OUT ON BOLTER HITTING HIS RT. KNEE.

3RD LEFT MAIN FALL IN #3 FACE ABOUT 40'L, 6'HIGH, 20' WIDE FALL ON RETURN ON #3 BELT IN #1 ENTRY ON LEFT 5'HIGH, 10' WIDE 45'LONG SPAD NO 491.

Cutting a hole in hydraulic oil can, poured oil in bolter, went to throw can and cut left hand.

FOUR ROOF FALLS HAVE OCCURED AT R DIFFERENT LOCATIONS ON THE 001-DMMU. THE ROOF FALLS ARE ABOVE THE ROOF BOLT ANCHORAGE ZONE. THE ROOF FALLS ARE APPROX 20' X 30' X 6' HIGH. THE ROOF FALLS IN THE #3 ENTRY IS IN THE INTERSECTION, THE FALL IN #5 ENTRY IS IN INTERSECTION. THE FALL IN #6 AND #7 ENTRIES ARE IN THE MAIN ENTRY

Making a splice, when he cut cable, knife slipped cutting his left hand.

Had fall in no #2 entry on main return. the fall is about 7 ft high, 18 ft wide from one end of block to the intersection. spad n459 50 ft inby spad.

EE WAS PUTTING FLIGHTS BACK IN FEEDER CHAIN WHEN HE WAS RE-INJURED (HERNIA). ORIG. INJURY AND DIAGNOSIS OF HERNIA 11/17/04. HERNIA WAS SURGICALLY REPAIRED APRIL, 2005.

THE MINER WOULD NOT TRAM. IT ACTED AS IF SOMETHNG WAS BLOCKING IT FROM TRAMMING. HE GOT DOWN AND LOOKED UNDER IT. WHEN HE DID, HE BUMPED IT, DISLODGING WHATEVER WAS HOLDING THE CATS. IT MOVED FORWARD AND MASHED HIM INTO THE RIB.

EE WAS MOVING THE ANCHOR WHEN THE WHEEL TOOK IT UP AND HIT EE IN THE ARM. EE DID NOT TURN SHUTTLE CAR OFF. EE DID NOT THINK WAS HURT THAT BAD. CAME TO WORK ON MONDAY, ARM STARTED SWELLING

Was welding on miner. A piece of draw rock fell and hit him on his hard hat, right arm and rolled down right leg.

EE WAS TRYING TO INSTALL A ROOF BOLT WITHOUT USING THE SLAB JACK. THE CANOPY WAS PUSHED DOWN ON EE HEAD WHEN EE PUT PRESSURE ON THE DRILL BOOM.

Rock slid off of canopy and struck injured in left arm, hip and lower back.

MOVING CONVEYOR MOTOR THAT COMES OFF MINER. HE WAS MOVING IT SO THAT HE COULD PICK IT UP WITH SCOOP & CLEAN BEHIND THE FOOT PADDLE.

INJURED KNEE. EE WAS PUTTING CONVEYOR CHAIN TOGETHER WHEN HE CAUGHT HIS FOOT ON THE RUB RAIL AND FELL OFF MINER.

WORKING ON A CONVEYOR CHAIN WHEN ANOTHER EMPLOYEE WAS USING A SLEDGE HAMMER TO HIT THE CHAIN. THE OTHER EE MISSED THE CHAIN AND STRUCK THE INDIVIUALS RIGHT HAND.

Employee was lifting on belt to put back in place when he felt lower back pain.

LIFTING ON EQUIPMENT PARTS AND PULLED SOMETHING

HE WAS PULLING CABLE; PAIN STARTED IN BACK AND NECK.

HE WAS LIFTING FOOT SHAFT AND FELT PRESSURE IN NAVAL AREA. A KNOT AROUND NAVAL MUSCLES IN STOMACH PULLED.

Bolting top, drill steel fouled up in top and steel broke, smashing employee's little finger on right hand against top breaking his finger in two different places.

While bolting top, draw rock fell out of roof striking ee on right side of body and leg.

HAD A ROCK FALL 1ST BREAK BETWEEN #3 & #4 INTERSECTION ABOUT 5' HIGH. REBOLTED & SET CRIBS & TIMBERS.

EMPLOYEE WAS PUTTING COIL BREAKER IN MINER HEAD - PUT HEAD OF MINER IN TOP OF ROOF TO PUT PRESSURES ON COIL BREAKER - WHEN THEY LEFT THE HEAD BACK DOWN - EMPLOYEE WENT TO GRAB THE COIL BREAKER - IT FLEW OUT AND STRUCK HIM IN THE FACE. EMPLOYEE SUSTAINED CUTS TO THE MOUTH AND LIP (9 STITCHES) , 1 BROKEN AND 1 LOOSE TOOTH, AND A CONCUSSION.

EMPLOYEE WAS RIDING MANTRIP TO SECTION. MANTRIP HIT KINK IN TRACK, BOUNCED EMPLOYEE AND HE LANDED ON A HAMMER AND LIGHT.

EE WAS RE-ENTERING MINE ON MANTRIP, DUCKED TO GO UNDER OVERCAST, DID NOT GO LOW ENOUGH. BEAM CAUGHT SHOULDER & PULLED HIM FROM MANTRIP. RECEIVED BRUISES & SCRAPES TO RIGHT SIDE OF FACE, EAR & RIGHT SHOULDER. HE WENT HOME FIRST THEN WENT TO CLINIC.

EE WAS USING GRINDER TO CUT PIECE OF KEY STEEL. GRINDER SLIPPED AND CUT HAND.

EE LIFTED CARTOUNGE AND STRAINED HIS BACK.

EE WAS REPLACING ROLLER TOP ON BELT LNE DRAW ROCK FELL AND HIT THE LEFT SIDE OF HIS FACE AND SHOULDER. CUT FACE AND BRUISED SHOULDER.

EMPLOYEE WAS USING A HAMMER TO TAKE A ING OFF THE CHUCK ON THE POT OF THE ROOFBOLTER WHEN A PIECE OF METAL CAME OFF AND CUT HIS LEFT FOREARM.

EE STARTED SCOOP UP AFTER REPAIRS - SCOOP STUCK ON POINT AND RAN THE SCOOP UNDER THE BELTLINE, PINNING HIS LEFT LEG BETWEEN SCOOP AND THE ROPE ON BELT LINE.

WAS MOVING BOLTER OVER TO BOLT AGAIN - HIT WRONG LEVER AND LET HIS CANOPY COME DOWN ON HIS HEAD.

EMPLOYEE WAS CLEANING BELT LINE AND FELL OVER A CABLE AND CUT HIS FINGER.

EE WAS PULLING BELT TOGETHER TO MAKE A SPLICE & CHAIN BROKE

WHILE TRAMMING BOLT MACHINE FROM BREAK TO ANOTHER DRAW ROCK FELL FROM BETWEEN BOLTS AND HIT EMPLOYEE ON THE HEAD.

EE SUPPOSELY HIT HIS HEAD WHILE WALKING UNDER OVER CAST, BREAK OFF TRACK AT BREAK 33 SEE ATTACHED NOTES.

#1 ENTRY TO #2 ENTRY 40 FT LONG, 20' WIDE 5 FT HIGH. 12 BREAKS INBY #2 HEAD DRIVE.