CHICO QUARRY: 1 muerte registrada Metal/Non-Metal

Employee was putting rocks in bucket to clean an area. He overfilled the bucket and lifted with no assistance and felt a pull on his lower right-side back.

CONTRACT LABOR, NOT AN EMPLOYEE AT APPROXIMATELY 9:30 PM WAS USING A COMEALONG TO PUT A HYDRAULIC MOTOR ON A FEEDER, WHEN THE COMEALONG SLIPPED AND THE HOOK AND HANDLE SMASHED AND CUT HIS RIGHT INDEX FINGER. ALSO SMASHED THE TOP OF HIS RIGHT HAND, CLOSE TO HIS INDEX FINGER.

Driller pulled truck over to park it and to get out of the truck. When he stepped out of the truck, a rattle snake bit him.

EE was assisting the foreman sort railroad iron with a backhoe. The foreman was pulling a piece of iron with the bucket of the backhoe when it became stuck & then suddenly came loose & flew striking the EE about 8" below the left knee; this resulted in a broken leg.

Employee was jumping over a ditch and injured his left knee. It was diagnosed as a strain. Doctor gave the employee a return to work release. Managment took him back to the doctor three times over the next six weeks. A speclist prescribed an MRI. On 03/07/2007, diagnosed the injury as a fracture and prescribed a leg brace. At this time it became a reportable injury.

Employee was crawling under a shaker tube when his face was cut by a metal burr on the tube. He was cut on the left cheek and received two stitches from a doctor.

DRILLER & HELPER WERE IN THE PROCESS OF REMOVING BROKEN DRILL STEEL FROM CAROUSEL. BAD STEEL WAS ATTACHED TO WINCH LINE PICKING IT UP TO LAY ON GROUND. HELPER WAS PUSHING STEEL AWAY FROM RIG WITH ONE HAND WHILE THE OTHER WAS ON THE RAILING FOR SUPPORT. DRILL STEEL SLIPPED FROM HELPERS GRIP AND SWUNG BACK AND SMASHED THE OTHER HAND AGAINST THE RAIL.

Driller has been complaining about carpal tunnel in his right forearm since approx. the date listed as accident date. He finally went to see a doctor who confirmed that he does in fact have carpal tunnel, but in both arms. Driller is supposed to have surgery sometime in the next month.

EMPLOYEE WAS HAMMERING A BELT OUT OF A BEARING WHEN A PIECE OF THE HAMMER CHIPPED OFF AND IMBEDDED IN HIS RIGHT INDEX FINGER.

Report late due to no contractor id#. Employee contacted 4160v bus bar. Employee mistakenly dissconnected wrong cut out switch on power pole. Employee trying to change out cable to 4160v motor when contact was made. Employee slightly burned on right hand & thigh. Taken to hospital, he was treated & released. After discussion with MSHA & receiving contractor # report submitted.

Employee cut left index finger while assisting with a chain hoist. finger was caught between chain and chain guide. 3 stiches on left index finger

EMPLOYEE CUT FINGER ON SHARP METAL ON MANUAL HOIST. (4 STITCHES) LEFT INDEX FINGER.

EE WAS OPENING A DOOR ON THE LOCOMOTIVE WHEN HIS HAND WAS CUT BY A SHARP PIECE OF METAL.

USING A Y WRENCH TO CHANGE A HAMMER. THE Y WRENCH GOT STUCK, HE STEPPED UP ONTO THE TABLE TO GET IT LOOSE AND AT THE SAME TIME THE DRILLER PUT THE DRILL IN ROTATION, CATCHING HIS FOOT BETWEEN THE WRENCH AND THE WRENCH STOP.

CUSTOMER'S TRUCK DRIVER WAS ATTEMPTING TO PLACE TARP ON THE TRAILER OF HIS TRUCK. THE ROPE HE WAS USING BROKE. HE FELL TO THE GROUND, STRIKING HIS HEAD. INJURIES INCLUDED LACERATED HEAD, STRAI NED NECK & BRUISES.

EE WAS CLEANING ROCKS OFF OF THE PRIMARY FEEDER WHEN A ROCK SLIPPED/FELL CRUSHING THE EE'S RIGHT HAND INDEX FINGER. THE FINGER WAS PARTIALLY AMPUTATED BY THE DOCTOR (FIRST JOINT).

EE WAS STRIKING A CHISEL WITH A HAMMER WHEN THE CHISEL SLIPPED & STRUCK THE EE IN THE LOWER LIP. 2 STITCHES IN LOWER LIP & 2 BROKEN TEETH.

EMPLOYEE WAS ENTERING A GONDOLA RAIL CAR WHEN HE SLIPPED AND TWISTED HIS KNEE WHEN HE LANDED IN THE BOTTOM OF THE CAR.

EMPLOYEE WAS WALKING AND TRIPPED ON A ROCK AND STRAINED HIS BACK.

EE WAS REPAIRING A CONVEYOR BELT AND CAUGHT HIS FINGER BETWEEN BELT AND THE FRAME.

EMPLOYEE WAS CUTTING A CONVEYER BELT WHEN THE KNIFE SLIPPED AND CUT HIS LEFT FOREARM.

DROPPED DECANT JAR AND CUT LEFT INDEX FINGER.

TWISTED LEFT ANKLE WHILE WALKING ON UNEVEN GROUND.

PORT A POWER SLIPPED PINNING EMPLOYEE'S FINGER AGAINST SPROCKET ON PRIMARY FEEDER. (8 STITCHES ON RIGHT MIDDLE FINGER.)

COMEALONG BROKE HOOK FROM COMEALONG STRUCK LEFT HAND CUTTING IT. 8 STITCHES IN LEFT HAND.

DROPPED A JAR WHICK STRUCK THE SIDE OF A SINK AND BROKE, EMPLOYEE TRIED TO CATCH THE JAR AND CUT HIS PALM OF THE LEFT HAND. (STITCHES IN LEFT HAND.)

EE WAS DESCENDING ACCESS LADDER ON A WATER TRUCK. HIS HIP POPPED CAUSING PAIN INLOWER BACK.

EE WAS USING A PRYBAR TO MOVE GUARD AWAY FROM MILL. THE BAR SLIPPED STRIKING HIM IN THE HEAD ABOVE THE RIGHT EYE. THE EE THEN FELL ON THE CATWALK AND BROKE A BONE IN HIS RIGHT HAND, SMALL FIN GER.

EE WAS HELPING REPLACE LINERS INSIDE OF CRUSHER-ONE LINER SLIPPED AND EE TRIED TO CATCH IT. INJURY SUSTAINED TO LEFT SHOULDER-PULLED TENDONS.

EE WAS HELPING INSTALL NEW ROLLERS ON A CRAWLER DRILL RIG. TO INSTALL THESE ROLLOERS YOU HAVE TO BEND OVER IN AN AWKWARD POSITION AND EXTEND YOUR ARMS. WHILE DOING SO EE FELT SOMETHING POP IN HIS BACK. HE WORKED THE REST OF THE DAY BUT THAT NIGHT BACK BEGAN TO STIFFEN UP AND HURT. CAME TO WORK THE NEXT MORNING AND WAS IN OBVIOUS PAIN AND WAS SENT TO THE DOCTOR.

EMPLOYEE STRAINED LOWER BACK WHILE SWITCHING RAIL CARS.

EE SHUT THE DOOR OF A BULLDOZER ON HIS LEFT INDEX FINGER. LACERATION REQUIRING SUTURES.

EMPLOYEE LIFTED A 60 LB ELECTRIC MOTOR CAUSING A STRAIN IN HIS BACK.

THE EMPLOYEE WAS HELPING HIS SUPERVISOR FREE A BLOCK ON A CRANE. THE EMPLOYEE'S LEFT RING FINGERGOT BETWEEN THE CABLE AND BLOCK CAUSING INJURY.

EMPLOYEE WAS CLIMBING INTO THE DUMP BED OF A CAT777 HAUL TRUCK. HIS RIGHT FOOT CAUGHT ONTO AN UNKNOWN OBJECT, TWISTING HIS LEG, CAUSING INJURY. BROKEN LEG, RIGHT LOWER LEG.

DRILLER WAS PUSHING BOTTOM OF DRILL PIPE INTO LOADER WITH HIS LEFT HAND. DRILL PIPE ROTATED CATCHING THUMB OF LEFT HAND IN BETWEEN THE LOADER AND THE DRILL PIPE SMASHING THE THUMB.

EMPLOYEE WAS USING SHOVEL TO CLEAN TUNNEL. AS HE WAS SHOVELING HE HEARD HIS LEFT SHOULDER POP.

EMPLOYEE WAS USING A BAR TO CLOSE RAIL CAR DOOR.THE BAR SLIPPED, STRIKING EMPLOYEE ABOVE HIS LEFT EYE. SIX STITCHES WERE REQUIRED TO CLOSE HIS WOUND.

EE WAS CLEARING CHUTE OF ROCK BLOCKAGE. A ROCK CAME LOOSE & STRUCK HIS RIGHT HAND

EMPLOYEE DROPPED AN ENGINE STARTER MOTOR ON HIS LEFT HAND,CAUSING A LACERATION TO HIS INDEX FINGER.

EMPLOYEE WAS ATTEMPTING TO ROLL V-BELTS ONTO BULL SHEAVE OF CRUSHER. HIS FOOT BECAME PINNED BETWEEN SHEAVE AND GUARD. RIGHT ANKLE CHIP FRACTURE.

EE WAS WALKING DOWN STEPS ON CATWALK, HE SLIPPED & FELL. HIS RIGHT LEG STRUCK THE HAND RAIL & WAS CUT.

EMPLOYEE WAS WORKING ON A FOOT VALVE WHICH HE HAD LAYING ON THE GROUND. AS HE WAS WWORKING WITH IT, IT ROLLED AND CUAGHHT HSI RIGHT RING FINGER BETWEEN THE VALLVEAND A SHARP ROCK CAUSING INJU RY.

EE STEPPED OFF LADDER ON HAUL TRUCK. HE TWISTED HIS ANKLE AS HE STEPPED DOWN ON THE GROUND.

EE WAS WORKING WITH A CO-WORKER TRYING TO FREE MATERIAL FROM A WASTE LINE. AS EE WAS PRYING AGAINST THE MATERIAL, CO-WORKER WAS HAMMERING ON THE LINE. THE MATERIAL CAME LOOSE & THE EE JUMPED CLEAR. AS HE WAS DOING SO, HE LAID HIS HAND ON THE LINE & THE CO-WORKER ACCIDENTLY STRUCK IT.

EE WAS USING A CUTTING TORCH TO CUT A CHUTE. HE UNKNOWINGLY CAUGHT HIS LEFT PANT LEG ON FIRE CAUSING BURN TO LEFT SHIN.

EMPLOYEE WAS CLEANING CATWALK AROUND SECONDARY CRUSHER. A ROCK FELL FRON AN OVERHEAD CONVEYOR STRIKING HIM ON THE LEFT SHOULDER.

EE WAS CLOSING ACCESS DOOR TO CRUSHER WHEN A ROCK WEIGHING APPROX 100 LBS FELL OUT OF THE CRUSHER AND STRUCK THE EE'S LEFT LEG.

EE WAS HAMMERING WITH A SLEDGE HAMMER AND STRUCK HIS RIGHT ELBOW ON THE HANDRAIL.

EMPLOYEE WAS CHECKING SCREEN DECK, WHEN THE CATWALK MATERIAL UNDER HIS FEET BROKE LOOSE. EMPLOYEE FELL 22' TO THE GROUND CAUSING BROKEN RIBS, PUNCTURED LUNGS AND HEAD INJURIES.

EE FELL OFF HAUL TRUCK WALKWAY. BROKE HIS RIGHT FOOT THE HEEL.

EMPLOYEE CUTTING A CONVEYOR BELT WHEN UTILITY KNIFE SLIPPED CUTTING EM,PLOYEES LEG

THERE WERE THREE COME-A-LONGS ON FEEDER, LETTING DOWN OONE COME-A-LONG AND THE ON EIN THE MIDDLE SLIPPED. EMPLOYEE WAS STANDING ON THE FEEDER. THE FEEDER DROPPED DOWN AND AWAY FROM WALL EMPLO YEE'S FOOT SLIPPED DOWN BETWEEN THE WALL AND FEEDER CAUSIGN A BROKE TIBIA.

EE STUMBLED WHILE WALKING TO PICKUP CAUGHT HIMSELF ON TAILGATE AND CUT THUMB.

EE WAS TRYING TO TURN BLOW BAR ROTOR BY HAND NOT WATCHING POSITION OF HIS HAND. TWO FINGERS WERE CAUGHT BETWEEN BLOW BAR AND WEAR LINER. HE HURT HIS FINGER ON HIS RT HAND. HIS FINGER NEEDED S TITCHES.

EMPLOYEE WAS CUTTING CONVEYOR BELT (RUFFER BELT) WHEN KNIFE SLIPPED & CUT HIS LITTLE FINGER ON LEFT HAND

EMPLOYEE SPILLED FUEL ON STEPS. THE EMPLOYEE WAS CLIMBING ON TO WATER TRUCK AND RIGHT FOOT SLIPPED. HIS RIGHT KNEE TWISTED. HE HURT HIS RIGHT KNEE. EMPLOYEE WENT TO THE DOCTOR ON 8-19-93 AND D ID NOT WORK ON 8-20-93.

EMPLOYEE WENT TO THE DOC ON 10-10-92 EMPLOYEE LOSTED TIME STARTED ON 10-12-92 EMPLOYEE PLACE A BOARD UPON THE SEAT BOARD SLIPPED OUT OF UNDER SEAT DRIVER EACHED OUT TO PICKUP BOARD THE BOARD & HITTED A BOMB CAUSING THE STEERING WHEEL TO HIM

67591TOR LOST HIS FOOTING AND FELL TOWARDS ROTATING DRILL STEM. THE ELBOW HIT THE ROTATING DRILL STEEL AND CUT THE SKIN. THE EMPLOYEE LOST NO TIME FROM WORK. THE CUT WAS DOCTOR TREATED.

54736YEE BENT OVER TO MOVE A BEARING WHEN HE RAISED UP, PAIN MOVE INTO HIS LOWER BACK.

49955R WAS CLIMBING DOWN FROM HIS HAUL UNIT WHEN HE STEPPED ON UNLEVEL GROUND. HIS RIGHT HIP TWISTED AND HE WENT TO THE DOCTOR. HIS 1ST LOSE DAY WAS 8-27-92.

55061S BACKING UP TO A STOCKPILE AND HIT THE PILE TOO HARD AND PULLED A CATCH IN HIS BACK THE EE FAIL TO TURN HIS BACK UP LIGGHT ON AND IT CAUSE HIGH TO MISS JUDGE HIS DISTANCE.

54736YEE WAS GETTING OUT OF THE WELDING TRUCK AND SLIPPED ON A LOOSE STEP ON THEW THE TRUCK.HIS FOOT LANDED IN A HOLE.

EMPLOYEE WELDING INSIDE ON CRUSHER. HE LIFTED HIS WELDING HOOD TO CHECK WELDING LEADS AND A SMALL DEBRIS GOT IN LEFT EYE CAUSING ABRASION ON LEFT CORNEA.

EMPLOYEE WAS WALKING OUT OF ELECTRIC SHOP. THE WEATHER WAS WET AND RAINING. EMPLOYEE SLIPPED ON THE MUD AND FELL ON HIS BUTT AND HURT HIS BACK. EMPLOYEE HAS HAD A HISOTRY OF BACK BEGAN PROBLEM S. EMPLOYEE WENT TO A DOCTOR ON APRIL 24, 1992 AND LOST TIME BEGAN ON 4-28-92.

EE WAS CUTTING A 1/2" METAL PLATE FROM A CHUTE. HE WAS PRYING ON THE PLATE AND A LOOSE METAL FELL AND STRUCK HIM ON THE FOREHEAD. HE WAS WEARING SAFETY GLASSES & WELDING HOOD.

DRIVER WAS DRAINING AIR TANK AND STEP OFF OF CATWALK ON HAUL UNIT FELL ABOUT 10' TO GROUND.

THE EMPLOYEE WAS HURT ON 03-09-90 DIDN'T LOSE TIME UNTIL 09-23-91 HE WAS OFF TILL 11-25-91 WORKED ONE WEEK THEN WENT BACK AS A LOST TIME TO HAVE OTHER KNEE OPERATED ON WENT ON LOST TIME DECEMB ER 3,1991.

WAS WALKING INTO ELECTRICAL SHOP AND STUMPED TOE AND FELL.

THE EMPLOYEE INFORMED ME HIS BACK STARTED TO HURT AT HIS HOME. THE EMPLOYEE SAID THIS INJURY WASCAUSED ABOUT ONE YEAR AGO BY JUMPING OVER A DUTCH IN FRONT OF PRIMARY TUNNEL. THIS INJURY IS A LOWER BACK INJURY WHICH COMES BACK FROM TIME TO TIME

DRIVING PIN OUT OF TOOTH METAL WENT IN KNEE CAP

HAUL UNIT WAS DUMPING IN AREA OF HIGH VOLTAGE LINES SPOTTER BACKED UNTI UNDER LINES THEN HAD HIM DUMP SPOTTER HAD HIM PULL FORWARD AND HE HIT THE OVERHEAD POWER LINES WHEN HE JUMPED OUT HE TUR NED AND WAS IN SHOCK.

EMPL STANDING ON HANDRAIL PRYING WITH A BAR USING HANDRAIL AS A LADDER.RAIL BROKE AND EMPL FELL.EMPL DIDNT REPORT ACCIDENT AS LOST TIME TIL CAME BACK FROM 1 DAY VACATION AND WENT TO DR.

EMPLOYEE WAS ON BELT WHEN IT STARTED EMPLOYEE SAID HE DIDN'T HEAR ALARM TO CLEAR BELT. ALL THREE EMPLOYEE KNOW THE DRILL WAS ENERGEZED BE FAR IT STARTED.

MECHANIC WAS PRYING WITH A BAR CHECKING BEARING PLAY ON A NEW HUDE DRUM HE WAS ABOUT TO INSTALL BAR SLIPPED & HE FELL BACK HITTING AGAINST SOME METAL ON FLOOR

SERVICE MECHANIC IN PROCESS OF REMOVING HOOD FROM DIESEL ENGINE THE HOOD WAS CONNECTED TO 35 CRANE HOOD GOT IN A BEND I NAME STEPPED ONTO DECK WHERE HOOD WAS BEING REMOVED WHILE TRYING TO GET TOOL TO RELEASE HOOD THE HOOD FELL ON FOOT

HE WAS CLEANING HIS WORK AREA. HE HAD REMOVED SOME STRUTS FROM WOODEN BOXES AND WAS CLEANING UP THE BOXES. HE STUCK A STAPLE INTO HIS THUMB ON LEFT HAND.

HE SET A BATTLE OF CRATER ON FLOOR OF DRAGLINE. HE STEPPED UP INTO MACHINE AND OPEN GUARD OVER SWING GEAR. HE TURNED AROUND BENT DOWN AND PICKED UP JUG OF CRATER. HE STHEN TURNED AS HE TURN ED HE LOST FOOTING OR STUMBLED AND HIS RIGHT HAND WENT INTO GEAR.

PULLING COUPLING ROD ON RAIL CAR NO SLACK IN CAR AND JERKED UP TOO HARD STRAINING LEFT ARM AND SHOULDER.

EMPLOYEE WAS HELPING REPLACE ROLLER ON CONVEYOR USING BAR UNDER ROLLER. HE WAS USING HIS LEFT HAND TO STEADY HIMSELF AND HAND SLIPPED CAUSING HIMT O FALL AGAINST FRAME OF CONVEYOR.

EMPLOYEE WAS CLEANING RAIL CAR AND WHEN GETTING OUT STEPPED ON LOOSE ROCK TWISTING RIGHT ANKLE.

EMPL SHOVELING ROCK FROM RAIL CARS BECAME ILL FROM HEAT AND/OR SUN.

EMPLOYEE ALLEGESD HE STRAINED HIMSELF WHEN HIS FOOT SLIPPED WHILE GETTING OUT OF HAUL UNIT & CAUSED HERNIA NAVEL AREA

EMPLOYEE WAS IN3TUNNEL CHECKING FEEDER,STARTED OU IN INCLINE WALKWAY,SLIPPED ON WET,MUDDY FLOOR LOSING BALNACE AND GETTING ARM INTO CONVEYOR.HE HAS AN OPEN FRACTURE TO RIGHT ARM/WRIST.

EMPLOYEE WAS HE5PING TO CLEAN ROCK FROM RAIL CARS. FOOT SLIPPED IN LOOSE CAUSING HIM TO FALL INTO PATH OF BACKHOE. BUCKET ON BACKHOE CAUGHT LEFT LEG PINNING IT AGAINST PATH OF BACKHOE.

EMPLOYEE WAS LI0TING ONE END OF HEAVY TEST TABLE FROM TRAILER, CARRYING IT INTO LAB. STRAINED BACK.

EMPLOYEE GRINDI3G ON EQUIPMENT TOOK GLASSES OF AND METAL GOT IN HIS EYE

EMPLOYEE WAS LI0TING ROCK FROM PLUGGED CRUSHER.

EMPLOYEE WAS GREASING AN IMPACT CRUSHER WHEN HE STEPPED DOWN OFF OF THE CRUSHER HE STEPPED ON A ROCK AND TWISTED HIS ANKLE

EMPLOYEE WAS GOING UP STEPS OF TOWER, KNEE LOCKED UP CAUSING HIM TO FALL AND STRIKE HIS LEFT KNEE.

EMPLOYEE WAS LI0TING CAN OF DIESEL FUEL TO POUR INTO WELDER. STRAINED BACK FIRST DAY LOST 10 21 85.

EMPLOYEE WAS FUELING HAUL UNIT, STIP BROKE CAUSING HIM TO FALL TO GROUND. HE RECEIVED INJURY TO HIS RIGHT KNEE. (EMPLOYEE STATES HE HAD PROBLEMS WITH THIS KNEE PREVIOUS TO THIS ACCIDENT BUT HAD NOT SEEN PHYSICIAN BECAUSE OF IT.)