Carroll Canyon Rock Plant Metal/Non-Metal

Employee was operating a forklift near a bulk Dust Foam tank when he ran over a PVC valve on the tank, breaking it. Some of the tank's contents began to leak which he attempted stop by using a rag to plug the valve's broken pipe. As he reached down to plug the leak, he cut his finger on a jagged piece of broken PVC pipe.

Prior to shift, victim was walking from his personal vehicle to the office. Another employee driving personal vehicle did not see victim and struck him, shattering pelvis and breaking hip. Conditions were predawn with unprecedented fog, visibility 25-50 feet.

Slipped and tripped on soft, muddy ground, straining knee. Medical treatment obtained on Monday, 12/13/10, at which time work restrictions were given by doctor.

Employee was replacing a screen cloth on a screen deck in the Tertiary tower. The screen was difficult to remove and the employee pulled at the screen vigorously causing strain to his upper back.

Employee was working with others repairing a crusher. As the employee was walking on the catwalk, he stepped on an uneven surface and twisted his ankle, causing him to fall. Employee was diagnosed with an avulsion fracture and placed on modified duty.

Employee was assisting with repairs in the Secondary MCC room that required crawling. The concrete caused injury to his right knee, that resulted in swelling.

Employee was entering the crusher hopper to begin replacing liners. Employee lost his footing on loose material lying on the belt and fell onto the liner wall striking it with his right shoulder.

A welding crew was working on the middle of three stacked screens, which had some rubber/urethane screens. The crew failed to mitigate the fire hazard posed by the hot work near/above flammable materials. During welding, slag or other hot debris fell to the lower screen deck, setting it on fire. The flames were out in less than 30 minutes. There were no injuries.

The employee was steadying the crusher distributor head as the crane was lowering to the crusher deck. As the crusher head leaned over, the chain slipped on the lifting eye pinching the employee's middle left finger between the lifting eye and the chain links. Laceration to finger requiring stitches, no lost time.

Employee was assigned to clean & repair reclaim belts counter weight guards in the Tertiary plant. While the employee was attempting to reinstall one of the panels, the panel came off the hooks on the opposite side smashing the employee's right hand little finger between the post & panel. Injury was not reported to supervisor until 7/2/08.

While carrying a 1 1/8' x 4' x 8' wire screen cloth in the tertiary tower the employee felt a strain to the upper back.

Employee was adjusting the 4 1/4 cone crusher with co-worker. After taking up the crusher by running some rock through, the workers began to re-set wedges. One of the posts started to drop. Employee grabbed the post with his left hand while co-worker shoved a wedge into its slot catching the employee's finger between the inside of the slot and the wedge.

While using a 12 lbs hammer to clear rocks form a vibrating grizzly screen, the employee struck the right index finger with the hammer.

While transporting a manlift from the concrete batch plant to the primary rock plant the employee hit a curb. When the left front tire hit the curb the employee was thrown forward hitting his lower ribs on his left side on the manbasket handle.

Employee went to put his welding helmet when a foreign body fell into his left eye.

While pulling 1" rope to tie onto a conveyor belt, the employee felt pain in his left shoulder.

Dumping fill dirt on grade, End-Dump trailer tipped over attached with Semi Tractor.

The employee was climbing down from the forklift he had been operating. As he stepped onto a rock, he lost his balance. In trying to catch himself from falling, he felt his right knee pop.

The employee was hammering a keeper pin in a new ripper shank guard on D11 dozer. He steadyed the guard with his legs while hammering, striking his left knee with the hammer.

While cleaning out a reclaimer drain, the drain sprung a leak. The cementitious water from the leak sprayed the employee in the face, dripping down into the right eye.

Employee was cleaning a pump impeller when a piece of calcium broke off. The calcium struck the employee in the mouth, cracking a right front tooth.

Hearing loss from cummulative trauma

EMPLOYEE WAS CUTTING RIBBER BELT WITH A RAZOR KNIFE WHEN THE KNIFE SLIPPED AND STRUCK THE EE'SRIGHT KNEE.

EE WAS GRINDING WELDS WITH A 7" GRINDER; GRINDING WHEEL STRUCK EE'S LEFT KNEE.

ROCK STRUCK EE WHEN LOADER OPERATOR DROPPED LOAD INTO FEEDER. EXCESS ROCK WENT OVER FEED WALL WHILE EE WAS DOING DAILY GREASING. INITIAL RESULTS WERE FOR EE TO RETURN TO WORK FULL DUTY. ON 4/29/03, EE HAD NOT IMPROVED. FOLLOW-UP MEDICAL TREATMENT PRESCRIBED MEDICATION AND TIME OFF WORK.

THE EE WAS PULLING A TAILPULLEY GUARD FROM THE BACK OF A SERVICE TRUCK. THE DOOR SLAMMED SHUT ON THE EMPLOYEE'S FINGERS OF HIS RIGHT HAND.

EMPLOYEE WAS CLIMBING DOWN THE LOADER LADDER AFTER LOWERING THE BUCKET TO THE GROUND. ABOUT HALF WAY DOWN, THE LADDER, HIS HAND SLIPPED OFF THE HANDRAIL WHICH CAUSED HIM TO FALL APPROX 4 FEET TO THE CONCRETE SLAB.

EE WAS UNLOADING BASKET (ONE THAT BRINGS IMPELLER FROM THE GROUND TO CANICA DECK) SETTING THEM OFF TO THE SIDE; STANDING THEM UP. WHEN GETTING ONE DOWN, IT FELL OVER TRAPPING HIS FINGERS BETWE REN THE 68# IMPELLER AND THE CANICA DECK (MOTOR MOIUNT).

WHILE REPLACING THE SCREEN DECK DISCHARGE LIP LINER, OLD LINER STRUCK EE ON LT FOREARM. THE FOLLOWING DAY IT WAS DETERMINED THAT FURTHER TREATMENT WAS REQUIRED, SUTURES.

EE LACERATED LEFT THUMB WITH A RAZOR KNIFE WHILE RESPLICING A 3.0 CONVEYOR BELT.

MAKING A NEW BELT CURTAIN FOR ROD DECK, USING A HOLE SAW TO MAKE BOLT HOLES. AS EE WAS TRYNG TO REMOVE BELT PLUG FROM THE HOLE SAW USING A SCREWDRIVER IT SLIPPED AND WENT INTO HIS RIGHT HAND.

EE WAS KNEELING DOWN ON TOP OF A 2"RUBBER LINER THAT HE WAS CUTTING WITH A UTILITY KNIFE. THE KNIFE SLIPPED AND HE LACERATED THE SIDE OF HIS RIGHT KNEE.

SCRAPING MATERIAL OFF GRIZZLEY ON POWERSCREEN, GOT OFF LOADER TO SHOVEL OUT TAIL PULLEY UNDER GRIZZLEY. WHEN HOPPER WENT EMPTY THE VIBRATION INCREASED AND A 6" TO 8" CLAY BALL FELL OFF THE SID E OF THE GRIZZLEY AND STRUCK THE EMPLOYEE ON THESIDE OF THE HEAD.

EMPLOYEE WAS WORKING WITH HAND TOOLS (WRENCHES) DOING CLEAN UP AFTER COMPLETION OF HEAD PULLEY-GEAR BOX WORK ON SECONDARY BELT.

CARRYING TABLE EDGE LINERS TO CANICA DESK WHEN A SHARP PAIN OCCURRED AT RIGHT ELBOW WHEN SETTING TWO EDGE LINERS DOWN ON CONICA DESK.

WORKING ON STARTER BOX FLASH BURNS TO RIGHT AND LEFT HANDS, FACE AND STOMACH.

EE WAS CUTTING A BOLT WITH A TORCH WHEN THE HOT BOLT FELL INTO A CRACK IN THE EE'S BOOT.

EE WAS INSTALLING A GRIZZLY BAR IN THE SCALPER. USED CRANE TO RAISE BARS UP TO THE SCALPER & THEN MOVED THEM INTO PLACE BY HAND WITH HELP FROM ANOTHER PERSON.

THE EMPLOYEE WAS MOVING PVC PIPE 3" AND 4" FROM NEAR THE BATCH PLANT TO THE PIT TO HOOK UP TO A WATER PUMP. ALL OF THE PIPE HAD TO BE CUT AND LOADED ON A TRUCK THEN UNLOADED AND PLACED WHERE NEEDED. AFTER A COUPLE OF HOURS, HIS BACK BECAMEVERY SORE AND STIFF.

EMPLOYEE WAS TRIMMING BACK THE RUBBER & PLASTIC ON ELECTRICAL WIRES TO INSTALL LUGS AS EMPLOYEE WAS TRIMMING WIRES THE KNIFE SLIPPED & EMPLOYEE CUT HIS MIDDLE FINGER ON HIS LEFT HAND EMPLOYEE WAS HOLDING THE KNIFE IN HIS RT HAND & THE WIRESIN HIS LEFT HAND

EMPLOYEE WAS EMPTYING A BUCKET OF TESTED MATERIALS WHEN HE PULLED A MUSCLE IN HIS BACK EMPLOYEE WAS BENT OVER SLIGHTLY DUMPING BUCKETS OF TESTED MATERIALS WITH AN UNDERHAND THROWING MOTION BUC KETS WEIGHTED APPROX 25LBS

EMPLOYEE WAS CLEANING BUCKET TEETH ON 992 LOADER. A PIECE OF THE TOOTH BROKE LOOSE WHEN IT WAS STRUCK WITH A HAMMER, A METAL PIECE FLEW OFF ADN STRUCK EMPLOYEE'S ARM.

EMPLOYEE STATES THAT WHILE AT WORK, HE HAS BEEN HAVINGA TIMGLING AND NUMBNESS IN BOTH HANDS AND ARM.

EMPLOYEE WAS CHANGING TEETH ON BUCK, ONE WOULD NOT COME OFF. HE HIT THE TOOTH FROM BEHIND AND PART OF THE TOOTH SPLINTERED AND LODGED IN HIS ARM.

EMPLOYEE WAS REMOVING AN EIGHT INCH BY 3/4" BOLT WITH A 3/4" WRENCH. HE PULLED HARD WITH HIS FEET UP ON THE CENTER WALL, INJURING HIS BACK.

EMPLOYEE WS CHANGING A 5/8 RUBBER SCREEN IN THE HEWITT ROBINS SHAKER IN THE SECONDARY PLANT TOWER. ANOTHER EMPLOYEE WAS ON ONE END OF THE SCREEN ATTEMPTING TO DISLODGE FROM TRAY. EMPLOYEE WA S BENT OVER SCREEN, PULLING UP ON SCREEN, WHILE A SECOND PERSON WAS USING PRY BAR TO DISLODGE SCREEN. AS EMPLOYEE PULLED UP ON THE SCREEN HE FELT A SHARP PAIN IN HIS LOWER BACK AREA.

HE WAS TRIMMING THE END OF A SIDE RAIL WITH CUTTING TORCHIN THE HEWEITT ROBBINS SCREENS. AFTER CUTTING, HE USED A PRY BAR TO REMOVE THE PIECE OF METAL, AS HE WAS PRYING HOT SLAG FLEW OFF AND GOT INTO HIS LEFT EYE.

EMPLOYEE WAS REMOVING CANICA PARTS OUT OF A 55 GAL DRUM (ER-33 FEED CONE). HE COULD NOT PULL THE PART OUT WITH THE BARREL UPRIGHT. HE THEN LAYED THE BARREL ON ITS SIDE. AS HE PULLED THE LOWER PART OUT, HE DID NOT NOTICE A PART ON TOP THAT HAD NOT FALLEN OVER. THIS PART FELL ON HIS RIGHT THUMB.

EMPLOYEE WAS SHOVELING FROM UNDER 7.1 CONVEYOR AT HEAD SECTION BEHIND COUNTERWEIGHT WHEN HE CRAWLED UNDER THE BELT TO GET DIRT HE COULDN'T REACH. HE STARTED SHOVELING WHEN THE HANDLE OF THE SH OVEL CAUGHT IN THE RETURN ROLLER BEHIND HIM AND JERKED THE SHOVEL FROM HIS HANDS AND THE SHOVEL BLADE HIT HIM.

A COLLAPSE OF THE SOUTH END OF THE .370 MANUFACTURED SAN RECLAIM TUNNEL OF APPROX. 25' OCCURRED ON MAY 6TH.

WHILE LIGHTING CUTTING TORCH FOR REPAIRMAN, A BACKFIRE IN TORCH CAUSED HOSE TO BURST NEAR LEFT WRIST. THE FLAME BURNED A SMALL AREA OF THE WRIST BELOW THE THUMB PAD. THE TORCH WAS FOUND TO BE DEFECTIVE.

EMPLOYEE WAS WORKING ON REMOVING THE SPEED SWITCH RETURN ON 5.1 CONVEYOR. HE WAS USING THE CUTTING TORCH, CUTTING OVER HIS HEAD. AS HE WAS CUTTING A PIECE OF SLAG WENT INTO HIS RIGHT EAR.

REPLACING DOOR IN CHUTE, FELT PAIN IN MIDDLE OF BACK

EMPLOYEE WAS WORKING ON THE SECONDARY CANICA VSI CRUSHER & WAS STOCKPILING PARTS FOR SERVICE HE STRAINED HIS WRIST PULLING PARTS FROM A 55 GAL BARRELL

EMPL LIFTING WATER PUMP BY THE HANDLE.THE PUMP OVERTURNED,SQUEEZING AND BENDING LEFT RING FINGER BETWEEN PUMP BODY AND HEAD.

EE WAS WALKING DOWN STAIRS FROM SECOND FLOOR TO PICK UP TOOLS FOR SCREEN JOB. HE MISPLACED HIS FOOTING ON 1 INCH CRUSHED ROCK ON STAIR TRED, AND TWISTED HIS LEFT ANKLE.

EE WAS DOING CLEANUP AND PICKED UP A LARGE PIPE ON CATWALK AND NOTICED BELT TRANINING WAS OFF. REPOSITIONED TROUCHING TRAINER, WALKED TO END OF CATWALK BY TAIL PULLEY AND STRUCK RETURN ROLLER BRACKET PIPE CAUGHT BETWEEN ROLLER AND BELT A SWUNG OTHER END OF PIPE AROUND, SMASHING EE S HAND AGAINST EDGE OF STRUCTURAL STEEL.

EMPL WAS CLEANING PUG MILL WITH LONG HANDLED SCRAPER. LEFT HAND HIT SIDE OF ONE OF BLADES.

HE WAS WORKING WITH ANOTHER EMPLOYEE, REPLACING A TROUGHING ROLLER. BOTH EMPLOYEES WERE HOLDING THE ROLLER AND TURNING IT OVER. THE OTHER EMPLOYEE PUSHED HARD BEFORE HE WAS READY, TRAPPING HIS HAND BETWEEN THE ROLLER AND THE CONVEYOR.

EMPLOYEE WAS GETTING READY TO SERVICE THE SWITCH FOR THE CANICA CRUSHER. HE FAILED TO DEENERGIZE THE ELECTRICAL SWITCH, AND THE MAIN GEAR EXPLODED.

EMPLOYEE WAS CHANGING THE TUB LINES ON CRUSHER. HE WAS REMOVING WORN PARTS FROM UNDER THE ANVIL RING. THE EMPLOYEE REMOVED MORE PARTS THAN NEED, CAUSING THE ANVIL RING TO DROP. THE RING FELL O NTO THE EMPLOYEE, WHO WAS PINNED BELOW IT FOR APPROX. 10 MINUTES.

EMPL WAS SHOVELING MATERIAL AROUND CONVEYOR IN SECONDARY PLANT & FATIGUED RIGHT SHOULDER & ARM.

EMPLOYEE WAS STANDING UP WHILE RUNNING A GRADER, AND IT HIT A ROCK AND JARRED HIS LOWER BACK.

EMPLOYEE WAS GRINDING ON TABLE ON TOP OF ROCK CRUSHER WHEN THE GRINDER SLIPPED OUT OF HIS HANDS AND TRAVELLED UP HIS ARM PAS AND OVER HIS GLOVES.

EMPLOYEE WAS TRUCING TO HAMMER OUT T-BAR. THE HAMMER BOUNCED OVER AND LACERATED HIS RIGHT INDEX FINGER BETWEEN THE NEXT T-BAR.

EMPLOYEE WAS USING CUTTING TORCH TO CUT OUT SNUBBER PULLEY AND A PIECE OF HOT SLAB WENT INTO HIS RIGHT EAR CANAL. EMPLOYEE HAD TO LAY UPSIDE DOWN TO CUT PULLEY OUT.

EMPL WAS MAKING REPIARS TO THE CEDAR RAPIDS WASH SCREEN WHEN THE WELDING LEADS GOT WRAPPED AROUND THE WELDER UPON CLIMBING ON THE BACK OF THE TRUCK TO UNWRAP THE LEAD EMPL LOST FOOTING AND STU CK R HAND OUT TO CATCH HIMSELF BUT STUCK IT DIRECTLY THROUGH THE FAN GUARD INTO THE WELDERS FAN

HELPING CHANGE INPELLARS IN CRUSHER STRAINED BACK LIFTING PARTS

TURNING TO REACH A RAG HURT BACK.

EMPL WAS OPERATING A R/T DOZER WORKING YELLOW FILL MATERIAL AT THE NORTH SIDE FILL CANYON EMPL WAS PUSHING MATERIAL FROM STOCK PILE ONTO NORTH SECTION OF PAD WHEN HE WAS EXECUTING A LEFT HAND RADIAL TURN HIS BLADE HIT A HARD SECTION OF THE GROUND AND THE L CORNER BIT DUG IN CAUSING THE DOZER TO JACK-KNIFE HE WAS USING HIS L ARM TO STEER AND HAD HIS L HAND ON STEERING KNOB WHEN THE

EMPL WAS OPERATING A DISC GRINDER IT WAS VERY WINDY DAY AND A FOREIGN OBJECT GOT UNDER HIS EYELID

STEEL LINERS WERE BEING SLID OVER THE SKIRTBOX TOWARD THE HOPPER WHERE THEY WERE TO BE INSTALLED.EMPLOYEE LOST HIS FOOTING ON THE CONVEYOT FRAME,FELL BACKWARDS WITH ONE FOOT CAUGHT IN THE FRAM E AND STEEL LINER FELL DOWN ON THE BACK OF THE EMPLOYEE HEAD.

EMPLOYEE WAS LIFTING AN ANVIL PIECE OF STEEL OUT OF THE CANICA CRUSHER EMPLOYEE EXPERIENCED PAIN IN HIS BACK AND GROIN AREA POSSIBLE MINOR HERNIA

EMPLOYEE WAS TAKING OUT CLAMP BAR BOLT WHEN CLAMP BAR SPRANG UP SMASHING HIS THUMB AGAINST THE SIDE OF SCREEN DECK

EMPLOYEE WAS STEPPING FROM CRANE WHEN HE SLIPPEDON STEPS AND FELL TO THE GROUND HITTING HIS ELBOW.

EMPLOYEE AS RETURNING TOOLS TO TOOL STORAGE BOX AT THE END OF WORK SHIFT. SOMEONE LEFT A PIECE OF ANGLE IRON RESTING AGAINST TOOL BOX. WHILE CLOSING TOOL BOX LID THE PIECE OF ANGLE IR ON OVER STRICKING EMPLOYEE IN MOUTH.

EMPLOYEE WAS PREPARING TO RELINE CHUTE WHEN WIND BLEW CHUTE HATCH CLOSED ON LEFT HAND

EMPL SLIPPED & FELL WHILE WALKING ON RUBBER BELTED CONVEYOR.

EMPLOYEE WAS TRYING TO WRAP CHAIN HOIST AROUND CHUNK OF SANDSTONE IN GRIZZILY, WHEN SANDSTONE SLIPPED AND PINCHED LEFT LITTLE FINGER CAUSING NEED FOR STITCHES.

EMP WAS CARRYIN1 SCREENS DOWN STAIRS, HE SLIPPED AND FELL HITTING HIS ELBOW AND NOSE, TWISTING HIS FOOT

CUTTING CONVEYO9 BELT WITH RAZOR KNIFE. THEKNIFE SLIPPED AND STRUCK EMPLOYEES LEG

WHILE PUSHING P5ATE ON BACK OF SERVICE TRUCK GLOVE CAUGHT ON PLATE ROLLED GLOVE TIGHT AGAINST FINGER AND TORE LOOSE A WART ON FINGER.

WHILE CLEANING 8ISCHARGE CHUTE OF ROD GRIZZLY A LARGE CHUNK OF MATERIAL FELL FROM UPPER PORT ION OF CHUTS & SLID DOWN ONTO LEFT ANKLE & FOOT

WALKING BY SCRE9N AND AROCK KICKED OUT AND HIT HIS WRIST.

MAINTENANCE ON 1RIMARY CANICA MOVING BROKEN CASTING PARTS AROUND ON GROUND.EMPLOYEE WAS PICKING THEM UP FROM AROUND CANICA DECK AND PILING THEM FOR REMOVAL.

EMPLOYEE WAS AS8ISTING WITH AN OIL CHANGE OF 8 X 20 VIBRATORY SCREENS IN SECONDARY PREMUM DUST PLANT. HE WAS BETWEEN DECKS, AND WHEN HE TURNED HIS HEAD TO SEE, HIS HARD HAT KNOCKED A LARGE AMO UNT OF VERY FIN9 DUST INTO HIS LEFT EYE.

EMPLOYEE WAS AS8ISTING IN CHANGING A CROSS BEAM. EMPLOYEE WAS HOLDING BEAM WHILE PARTNER WAS APLLYING FASTENERS.

EMPLOYEE WAS WA5KING ON EVEN GROUND AND HIS LEFT ANKLE TWISTED AT THE SAME TIME AS HIS KNEE.

EMPLOYEE WAS W9LDING WITH TWO OTHER MEN ALSO WELDING

EMPLOYEE HAD NO3SPECIFIC CAUSE OF INJURY.HIS RIGHT HAND IS BRUISED,SWOLLEN AND NUMB AND HIS LEFT HIP WAS SRAINED WHILE MOVING STEEL.

EMP DIDNT STATE3A SPECIFIC CAUSE OF INJURY, BUT HE STATES HE STRAINED HIS LOWER BACK

WHILE EMPLOYEE 4AS PULLING PLATE UNDER THE CHUTE HE TWISTED HIS BACK.

EMPLOYEE WAS TH9OWING OFF STONES FROM CONVEYOR AND A SANDSTONE FELL OFF END OF CONVEYOR AND FELL ON FOOT.

EMPLOYEE WAS MO5ING 1/2 INCH STEEL AND DROPPED IT ON HIS FINGER AND SMASHED AND CUT IT.

EMPL STEPPED OF0 I-BEAM AND SPRAINED LEFT ANKLE.

EMP WAS REMOVIN1 CRIBBING FROM UNDER PIONEERSCREEN WHEN HIS LEFT HAND WAS STRUCK BY ANOTHER EMPLOYEE WITH A PIG BAR ON THE BACK OF HIS HAND

EMP WAS ADJUSTI3G SPRING ON VIBRATING SCREEN AND A SPRING GOT LOOSE AND STRUCK HAND AS IT FELL INTO THE WORK AREA

EMPLOYEE WAS SH2VELING OFF CAT WALK AREA WHEN HE SCOOPED SHOVEL INTO PILE AND SHOVEL HIT ROCK THAT WOULD NOT MOVE IN GRATING AND TWISTED RIGHT WRIST.

EE WAS DRIVING 3NTO PARKING LOT & HIT ANOTHER VEHICLE IN PARKING LOT.

000000050686030212 1211 EMPLOYEE WAS PASSENGER IN TRUCK F207, THE DRIVER, I NAME CLAIMED THE THROTTLE STUCK AND HE LOST CONTROL OF THE VECHILE AND STRUCK CONVEYOR IN WH

EMPLOYEE WAS RE7URNING FROM LUNCH IN TRUCK F207, HE CLAIMED THR THROTTLE STUCK AND HE LOST CONTROL OF THE VEHICLE AND HIT THE SUPPORT COLUMN OF THE CONVEYOR. VEHICLE WAS STOPPED APPROX. 75 FT FROM COLUMN TO3INSPECT A JOB, UPON STARTING TO TRAVEL TO SECONDARY PLANT, ACCIDENT OCCURED.

EMPL SHOVELING 5ND CLEANING UP AND EXPERIENCED SHARP PAIN IN CHEST.

EMPLOYEE WAS CL3MBING DOWN LADDER FROM 060 HEAD PULLEY DECK TRYING TO CATCH JACK HAMMER THAT FELL DOWN CHUTE BEFORE IT WENT INTO WASTER PILE AND SLIPPED ON LADDER

EMPLOYEE WAS CH9CKING PRIMARY PLANT AND A ROCK FELL DOWN OFF OF A CONVEYOR AND HIT EMPLOYEE ON THE LEFT SHOULDER.

EMPLOYEE WAS IN8PECTING NEW WELDS ON MOTOR,HE SLIPPED AND PUT HIS HAND OUT TO BRACE HIMSELF,HE SLIPPED ON A ROCK AND FELL INBETWEEN THE HAND OUT TO BRACE HIMSELF,HE SLIPPED ON A ROCK AND FELL INBETWEEN THE H9AD PULLEY AND FRAME.HIS HAND WAS PINNED BETWEEN HEAD PULLEY AND FRAME.

EMPLOYEE WAS WA5KING AND FELL INTO A CONCRETE DRAINAGE DITCH APPROX.3'X3'.

EMPLOYEE WAS GE7TING OUT OF BOBCAT AND COULDN'T STRAIGHTEN OUT HIS BACK.

EMP WAS REMOVIN1 SKIRT BOARD, IT CAME LOOSE, SPRANG AND HIT EMPLOYEE ON THE FOOT

EMP WAS PREPARI3G TO CHARGE SCREEN ON SCREEN DECK AND FELL OFF EDGE RESULTING IN A LACERATION TO LEFT LEG

EMPLOYEE WAS WO9KING ON SCREENS, DRIVING IN WEDGE BOLTS AND HE SMASHED HIS FINGER WITH A HAMMER.

EE WAS USING A 4ACK HAMMER TO CLEAN A CHUTE WITH A WALL OF SOLID DIRT. A CHUNCK OF DIRT FELL ON HIS FOOT.

EMPLOYEE WAS US3NG A BAR TO FREE SOME ROCKS ON THE CONVEYOR BELT, ONE OF THE ROLLER BECAME FREE PULLING THEBAR AND THE EMPLOYEE'S HAND THROUGH THE CONVEYOR BELT.

EMP WAS CHECKIN1 OIL AND STRAIGHTENED UP AND BANGED HEAD ON TRUCK