CZ-30(ZONA) Metal/Non-Metal

Employee was working on a fault light on the main breaker box when the box exploded causing burns to both eyes.

Employee went to start the outboard motor and it was in gear. To prevent cranking the motor in gear, the rope will not come out when the motor is in gear. He pulled hard on the rope and pulled a muscle in his lower back because the rope did not come out.

Employee was working on the dredge pump and logwasher, picking up heavy parts and breaking bolts loose with a pull handle when he strained his lower back.

When finishing up a weld, the shield was raised and the rod left over would strike the metal sometimes causing an arc exposing the eyes to it. The employee burned his eyes.

EMPLOYEE WAS UNSTOPPING A SAND LINE AND A RUBBER HOSE HIT HIM ON THE LEFT LEG. HIS UPPER LEG WAS BROKEN.

Employee was patching a pipe and it mashed his pinky finger.

Employee was attempting to hit a bolt with a hammer and mashed his finger.

Employee was tightening a cable on the back of the gravity plant when the excavator bucket leaked down and caused a pipe to slide and smash his left foot.

While trying to get a dredge going, employee became overheated while in the boat.

Employee was welding on a stacker. When he stood up, he cut his head by hitting it on the stacker.

EE was over-heated. He was light-headed and nauseated-heat exhaustion.

EE WAS UNLOADING A BED ROLLER WHEN HIS RIGHT HAND GOT PINCHED BETWEEN 2 OF THEM.

He attempted to lift a 4D battery & strained back.

EMPLOYEE HAD WORK RELATED INJURY AT A NON-MSHA SITE ON 9-29-03. AFTER HE RETURNED TO WORK, HE HAD A SEIZURE WHILE SITTING IN A CHAIR IN THE CONTROL HOUSE. GOT LACERATIONS AND BRUISES ON FACE AND NOSE.

EE WAS STANDING BETWEEN 2 SHAFTS IN LOG WASHER RECONNECTING LOG AFTER REPLACING A BROKEN PART. COME-A-LONGS WERE POSITIONED SO THAT THEY NOT ONLY PULLED LOG, BUT ALSO PICKED IT UP - CAUSED LOG TO SWING AND PIN EE'S RIGHT LEG BETWEEN THE LOGS.

EMPLOYEE CALLED 3/7/03 TO SAY HE HAD A SHARP PAIN IN RIGHT THIGH. HE SAYS HE MAY HAVE HURT IT BY WALKING THE "WRONG WAY" ON THE MUD BELT ON 3/5/03 - OR HE MAY HAVE HURT IT 2 WEEKS AGO WHILE WO RKING ON THE DRILL TRUCK TOWER. NORE: ON 2/21/03 EMPLOYEE CALLED IN TO SAY HE HAD HURT HIS GROIN AT HOME THE NIGHT BEFORE. HE WAS OFF WORK UNTIL 2/27/03.(SAME TIME HE SAYS HE HURT IT ON DRILL

EE WAS WORKING OFF THE PADDLE WHEEL DREDGE, PULLING A CABLE TO WRAP AROUND A PIPE. HE CALLED THE NEXT DAY & REPORTED THAT HE HAD PULLED A MUSCLEIN HIS BACK.

HE WAS REMOVING A HOSE BAND ON A 3" RUBBER HOSE. THE HOSE HAD FACTORY INSTALLED FASTENERS THAT HAVE TO BE REMOVED BY SAWING OFF. HE WAS SAWING THROUGH THE HOSEBAND WITH A HACKSAW. WHEN HE CUT THROUGH, THE FASTENER POPPED BACK AND CUT HIS LEFT INDEX FINGER.

EE WAS STANDING ON A CRANE ON THE LEFT REAR SIDE BY THE HYDRAULIC TANK WORKING ON THE HYRDRAULIC LINES. HE LOST HIS FOOTING, SLIPPED AND FELL 5 FEET TO THE GROUND.

EE WAS PUNCHING HOLES IN CONVEYOR BELT USING A PUNCH & CLAW HAMMER. THE HAMMER GLANCED OFF THE PUNCH & HIT HIS LEFT INDEX FINGER AT THE BASE KNUCKLE.

EMPLOYEE WAS ON THE MUDBELT. THE BACKHOE WAS PUSHING THE MUDBELT BACK. THE HEADLINE ROPE CAME LOOSE AND HIT EMPLOYEE ON THE LEFT ARM CAUSING A FRACTURE.

EE WAS USING A WRENCH TO REMOVE DRILL PIPE FROM THE GROUND. THE WRENCH SLIPPED OFF THE PIPE & CAUGHT THE RING FINGER ON HIS RIGHT HAND BETWEEN THE PIPE AND THE RAIL OF THE DRILL RIG.

EMPLOYEE WAS WORKING WITH DRILL RIG OBTAINING SAND AND GRAVEL SAMPLES. SAND OR RUST BLEW OFF PIPE INTO HIS RIGHT EYE.

EMPLOYEE WAS WORKING ON CREW WITH DRILLD RIG OBTAINING SAND AND GRAVEL SAMPLES. HE WAS SHOVELING SAND AND GRAVEL SAMPLES WHNE HE HURT THE BACK OF HIS NECK AND LEFT SHOULDER.

EE WERE PUTTING A PIPELINE BACK TOGETHER, LIFTING THE PIPE AT AN ANGLE. THE HOIST FOOK THAT WAS HOOKED INTO THE CHAIN WELDED ON THE PIPE CAME LOOSE AND STRUCK HIM IN THE LEFT SIDE OF THE FACE.

EE WAS WALKING DOWN AN EMBANKMENT TO BOARD A WORK BOAT FOR TRANSPORT TO DREDGE. GROUND WAS WET. HE SLIPPED AND SLID DOWN EMBANKMENT. HIS RIGHT HEEL WEDGED BETWEEN BOAT AND BANK. HE CAUGHT HIMS ELF WITH HIS RIGHT ARM AND HIS ARM AND SHOULDER HIT THE BANK HARD.

EE WAS HELPING TEAR DOWN A GRAVEL PROCESSING PLANT. HE WAS HELPING LOWER THE FRAME FOR A CONVEYOR BELT. FRAME WAS SET DOWN BUT NOT SECURED. THE FRAME SHIFTED AND SLIPPED DOWN ON HIS FOOT.

EMPLOYEE WAS WORKING ON A FRONT END LOADER WHEN THE WIND BLEW SAND OR DIRT OR SOME OTHER UNIDENTIFIED DEBRIS INTO HIS EYE. THE EYE WAS WASHED OUT AT THAT TIME. ON 2-29 THE EMPLOYEE SAID HIS EYE WAS IRRITATED AND WE SENT HIM TO THE DOCTOR TO BE EXAMINED.

EE WAS GETTING OUT OF AN ALUMINUM ROWBOAT ONTO A PONTOON. WHEN HE REACHED FOR THE PONTOON, THE ROWBOAT FLIPPED. HE HIT THE PONTOON WITH HIS KNEE AND HIP AND FELL INTO THE POND. HE HAS A BRUISE D KNEE AND A PULLED MUSCLE IN THE HIP.

EE WAS FUELING BACKHOE HE STEPPED ON TRACK TO REMOVE FULE HOSE FROM TANK. THE TRACK WAS DAMP HE SLIPPED & HIT HIS LEFT ELBOW ON THE BACKHOE

THE EE WAS MOVING A SAND BLASTING POT, WHICH IS MOUNTED ON WHEELS, BY PULLING IT. HE STRAINED A MUSCLE IN HIS BACK BEHIND HIS LEFT SHOULDER.

EE WAS FILLING SAND BLASTING TANK WITH BLASTING SAND. HE WAS BENT OVER, AND WHEN HE TRIED TO STAND HE WAS NOT ABLE TO STAND UP STRAIGHT.

EMPLOYEE AND ANOTHER CO-WORKER WERE PREPARING TOPUT OIL ON A DREDGE. THE OIL RACK WAS LAYING ON AN ELECTRIC WIRE, SO THEY LIFTED IT(OIL RACK) TOMOVE IT OFF THE WIRE. LATER IN THE EVENING, EMPL OYEE COMPLAINED OF BACK PAIN AND WAS SENT TO THEEMERGENCY ROOM TO BE CHECKED.

EMPLOYEE WAS HELPING MARK PROPERTY LINE AT GRAVEL PLANT. WHILE WALKING IN GRASS, HE GOT SEVERAL TICKS ON HIM. ON 8-2-99, EMPLOYEE REPORTED TICK BITE ON NECK THAT WAS SORE. HE WAS SENT TO DOCTOR'S WHO DIAGNOSED THE INFECTION AS A RESULTOF A TICK BITE.

ON 6-7-99 EE REPORTED THAT HE WAS WELDING IN A TIGHT SPOT BETWEEN 2 PONTOONS. WHEN HE CLIMBED OUT, HE TWISTED HIS BACK. HE TOOK ADVIL AND WORKED THE REMAINDER OF THAT DAY AND ALL DAY 6-8-99. O N 6-9-99 HE ASKED TO GO TO DR AND WAS OFF WORK ONE DAY.

EMPLOYEE WAS WELDING ON THE CUTTER SYSTEM FOR A DREDGE AND BURNED HIS EYES.

EE WAS ASSISTING ANOTHER EE WITH SAND BLASTING. EE WAS MOVING THE HOSE WHEN THE CONNECTION BETWEEN THE HOSE & THE SAND POT BROKE LOOSE. EE'S RIGHT HAND WAS SAND BLASTED.

EE WAS WELDING ON A PONTOON AND BURNED HIS EYES. EYE DROPS WERE PRESCRIBED FOR HIM AT THE ER.

EE WAS WELDING INSIDE PONTOONS. SMOKE AND/OR FUMES MADE HIM ILL. SYMPTOMS INCLUDED DIFFICULTY BREATHING, SORE THROAT, COUGHING, ETC.

WELDING ON A PIECE OF PIPE-HE STOPPED TO CHIP OFF SLAG FROM THE WELD WITH A HAMMER. A PIECE OF HOT SLAG WENT DOWN IN HIS BOOT AND BURNED HIS ANKLE.

HE WAS REPLACING THE CUTTING EDGE ON A WHEEL LOADER WHEN HIS FINGER SLIPPED AND WA CUT ON THE EDGE OF THE BUCKET. HE CUT THE LITTLE FINGER ON HIS RIGHT HAND, RECEIVED 6 STITICHES, TETANUS SHOT AND ANTIBIOTICS.

EE & ANOTHER EE WERE USING A PRY BAR TO TURN THE SHAFT IN THE CUTTER BOX ON DREDGE. THE SHAFT HUNG UP. EE STRAINED HIS MIDDLE, LOWER, LEFT BACK.

EE WAS REPLACING THE STARTER ON CAT LOADER. HE HAD TO BEND DOWN AND REACH OVER THE FRAME TO REACH THE STARTER. IN DOING SO HE STRAINED HIS LOWER RIGHT BACK. HE DID NOT REPORT BEING INJURED UNT IL 6-1-98.

EMPLOYEE WAS TYING OFF PIPE(WITH ROPE) IN A FLOATING PIPELINE. THE WIND CAUGHT THE PIPE AND MASHED EMPLOYEE'S FINGERS BETWEEN THE ROPE AND A CLEAT.

EMPLOYEE LIFTED A 6"X 30' LONG PIPE ONYO A BLOCK IN ORDER TO CUT IT. AT 5:00AM ON 2/20/98 HE BEGAN EXPERIENCING CHEST PAIN. HE REPORTED TO WORK & AT 7:00 AM WAS TAKEN TO THE HOSPITAL. AFTER OB SERVATION, HE WAS DIAGNOSED WITH A CHEST WALL STRAIN.

EMPLOYEE WAS TIGHTENING BOLTS AND A COUPLING ON DREDGE USING A WRENCH. THE WRENCH SLIPPED AND CUT HIS THUMB. NO STITCHES WERE REQUIRED- NO BONES BROKEN-SPLINT AND BANDAGE.

EMPLOYEE SHUT DOWN FRONT END LOADER. HE BENT OVER TO EXIT THE CAB. WHEN HE STOOD BACK UP, HE HAD A BACK PAIN IN HIS LOWER BACK.

EE WAS BOLTING REPLACEMENT PADDLES TO LOG WASHER. THE WEIGHT OF THE PADDLES APPARENTLY CAUSED THE SHAFT OF THE LOG WASHER TO TURN, TRAPPING HIS RIGHT LOWER LEG.

EMPLOYEE HAD BEEN WORKING ON LOG WASHER, STANDNG ON A PIPE 4' ABOVE GROUND. WHEN HE WA FINISHED, AND READY TO GET DOWN, INSTEAD OF GOING TO THE LADDER TO DESCEND, HE JUMPED FROM THE PIPE TO T HE GROUND. HE TWISTED HIS RIGHT KNEE.

EMPLOYEE WAS CRANKING A GENERATOR. HE TORE MUSCLE IN HIS CHEST AWAY FROM THE STERNUM.

EE WAS CHANGING THE HEATER HOSE ON A LOADER & TWISTED HIS BACK.

EMP WAS CHANGING OUT A 16" PIPE. PIPE WAS INSERTED IN ONE SLEEVE. HE WAS MOVING PIPE FORWARD TOWARD NEXT SLEEVE USING A BACKHOE TO SWING PIPE. PIPE BUMPED HIM ON LEFT KNEE AND SHIN AREA. PIPE SWUNG AROUND PINNING HIM BETWEEN PIPE AND TRACK ON BACKHOE.

EMPLOYEE PLACED A BEAM ON THE TAILGATE OF A TRUCK. HE WAS TURNING THE BEAM TO CUT A PIECE OF PLATE OFF OF IT. A BURR ON THE BEAM STUCK IN THE PLAM OF HIS LEFT HAND. THE TURNING MOTION CAUSED T HE BURR TO RIP A DEEP, NARROW CUT IN THE PALM.

EMPLOYEE LIFTED A HOME-MADE CABLE BLOCK INTO A LOADER BUCKET, HE STRAINED MUSCLE IN HIS LOWEER LEFT BACK AND LEG.

BUILDING A COUNTERWEIGHT TO CHECK SCALES. WAS WELDING A LID ON TOP. LID DID NOT FIT FLUSH WITH EDGE OF BOX. EE WAS HOLDING LID, KIND OF SQUATTING, BALANCING WITH LEFT HAND & WELDING WITH RIGHT HAND. HE WAS TWISTING AS HE WELDED ALONG OPENING & HE TWISTED HIS LEFT SHOULDER & PULLED MUSCLE.

EE WAS DRIVING A DUMP TRUCK WHICH HIT A HOLE IN THE ROAD. EE SAYS HE WAS WEARING HIS SEAT BELT, BUT WAS THRU AROUND THE CAB OF THE TRUCK. HE COMPLAINS OF LOW BACK PAIN.

EMP WAS REPINNING A SPUD ON A DREDGE. ACCIDENTALLY STUCK HIS FINGER IN THE SPUD CYLINDER HOLDER.CYLINDER MASHED HIS RIGHT INDEX FINGER CAUSING AFRACTURE TO THE FINGER.

EE WAS TYPING UP A PADDLE WHEEL DREDGE USING A CABLE WITH A WINCH. HE APPARENTLY DID NOT HOOK THE CABLE SECURELY IT CAME LOOSE AN DHIT HIM IN THE SIDE OF THE FACE. HE REFUSED TO GO TO DR. WORK ED ALL DAY WITHOUT COMPLAINT. CALLED IN 8-18-95.AND WENT TO DR.

THE EMPLOYEE JUMPED FROM THE TIRE OF A GROVE CRAIN TO THE GROUND HE HURT HIS LEFT SIDE THE EMPLOYEE THOUGHT HE WOULD BE OKAY BUT SAID HE WAS STILL SORE & NOT SLEEPING WELL SO HE WENT TO DOC 03 -27-95 HE IS ON LIGHT DUTY MISSED WORK 03-28 DUE TO ADVERSE REACTION TO MEDICATION

THE EMPLOYEE WAS LEANING OVER TO ROLL OVER A PIECE OF H-BEAM. HE PULLED A MUSCLE IN HIS LOWER BACK.

EMPLOYEE WAS FUELING FRONT END LOADER. HE STEPPED OFF THE LOADER ONTO THE RAILINGS AND MISPLACED HIS FOOT. HE FELL ONTO THE RAILINGS AND CATWALK, HITTING HIS CHEST AND PUNCTURING HIS RIGHT LEG .

EMPLOYEE WAS ASSISTING ANOTHER EMPLOYEE UNLOADING 55 DRUMS OF HYDRAULIC FLUID USING CRANE HOIST TYPE LIFT WITH CHAINS DRUM SWUNG TOWARD EMPLOYEE INJURING SHOULDER

EMPLOYEE REPORTED THAT HE WAS PERFORMING REPAIRS TO LOG WASHER ON DREDGE AND "BUMPED HIS KNEE". WE WOULD LIKE TO NOTE THAT EMPLOYEE DID NOT REPORT THE ALLEGED INJURY UNTIL TWO DAYS LATER.

EMPL SITTING ERECT WITH FEET AND LEGS STRAIGHT IN FRONT OF BODY USING COME-ALONS TO MAINTAIN POSITIVE TENSION.TRYING TO CORRECT THE LOCATION OF TRAVELING SPUD ON GRAVEL DREDGE.

STANDING UPRIGHT PREVIOUSLY HAD TRIPPED AND FALLEN OVER PC OF DEBRIS PAIN IN BACK AND LEGS.

IT IS UNKNOWN AT THIS TIME EXACTLY WHEN AND HOW EMPLOYEE WAS INJURED. THE DIAGNOSIS FOR THE INJURED EMPLOYEE IS "BACK PAIN, RADIATING TO LOWER LEG." THE EMPLOYEE WENT TO THE DOCTOR ON OR ABOUT 8/10/90.

EMPLOYEE WAS REPLACING TEETH ON CUTTER WHEEL,USING A HAMMER,WHEN A SLIVER OF METAL DISLODGED LACERATING LEFT ARM.

EMP WAS TRANSFE9ING DRILLING RESIDUE FROM FILTERING PAN WITH A SHOVEL AT APPROX 2 PM 10 06 86 INTO A PIL E NEAR THE PAN HE BEGAN COMPLAINING OF BACK PAIN BUT WAS ABLE TO3COMPLETE THE FULL DAYS WORK APPROX 4 HOURS UNTIL 6 PM

EMPLOYEE WAS ST9PPING DOWN FROM BACKHOE, SLIPPED, AND INJURED LEFT ANKLE.