FORT LUPTON SAND & GRAVEL: 97 citaciones de la MSHA Metal/Non-Metal

EE attempted to start the truck, but the battery was dead. EE went to grab the jumper cables lying on the ground and felt a sharp pain in their lower back.

After replacing the tail pulley on the bridge belt, the operator, in the basket with fall protection attached, was moving the manlift with the basket approximately 4 feet above the ground. The jib boom failed and the basket dropped to the ground. This caused the operator to strike the basket resulting in a compression fracture of a vertebra and sprained knee.

Shoveling the Tunnel and was shoveling material back onto the belt when felt a pop in their back.

Using a sledgehammer to drive in the bucket pin on the loader, they noticed that left wrist and hand were sore. Employee reported but did not see a doc until the 15th.

They were using a come along to pull the motor tension back, this allowed them to replace the drive belt onto to the pulleys. Come along slipped causing the motor to land on EE's hand.

It was a flat area near our roadbase production area where we were moving a conveyor head section.

Employee was lifting a section of pipe, employee was lifting with another employee when back started to hurt. Also moved some 5 gal buckets which made it worse.

A tube was being fed through the catwalk with a loader, with two employees guiding it on the catwalk. While lifting the tube on shoulder, one employee felt pain in shoulder. Upon investigation, the employee felt employee put too much weight on one shoulder and was not lifting properly.

Working on conveyor frame when employee's finger was pulled in between the two frame flanges by their gloves.

EE and co-worker were working on the tail pulley shaft for the mainline stacker. They had taken a come along and attached it to the shaft of the tail pulley and pulled the shaft backwards. When EE went to remove the bearing from the shaft the bearing turned and crushed EE's finger in between the bearing and the tail pulley adjuster.

A conveyor belt that was needing to be replaced, employee cut hand with knife.

While attempting to loosen the adjuster jam nut, EE placed both feet against the crusher frame in an attempt to increase leverage. Before I even realized what ee was doing, the nut loosened causing ee to fall to the deck.

As EE was putting on harness below the cat walk of the McCloskey R155. Co-worker was climbing into the hopper from the cat walk, to shovel. Co-worker threw the shovel towards the hopper and missed. When co-worker missed, the shovel fell back down and hit EE on the brim of hard hat and glanced off of neck.

Getting out of the truck to clock out at the end of the day and slipped on some ice and fell

Right foot got caught by concrete debris on levy. Slipped on mud when stepping over other debris with left foot. This caused his right knee to twist and hyper-extend.

Using left arm to activate switch and right hand to hold open the access panel and the panel slipped and struck his left arm.

Pulling hydraulic assembly out of backhoe when it allegedly slipped out of hand and dropped on finger.

Employee was climbing up the ladder of his loader when he suddenly experienced a sharp pain in his lower back.

Employee removing grease tube from grease gun with knife and allegedly cut thumb.

Allegedly EE was grinding when the grinder kicked back and hit his leg. The grinder did have a guard.

The ee allegedly injured his right shoulder when he slipped on ice and fell down landing on his shoulder. He has not lost any time from work but has been put on restricted duty.

EMPLOYEE ALLEGES THAT HE WAS HELPING A TRUCK DRIVER STRAP DOWN A LOAD OF CONVEYORS WITH A BOOMER AND CHEATER PIPE, WHEN IT RELEASED AND THE PIPE HIT HIM IN THE NOSE.

EMPLOYEE ALLEGE8 HE WAS USING IMPACT WRENCH TO REMOVE BOLTS FROM ROLLER.HAND WRENCH HOLDING NUT SLIPPED AND SMASHED FINGER BETWEEN WRENCH AND ROLLER.

EE ALLEGES THAT WHEN LIFTING PUMP HOUSING WITH A CHAIN & OVERHEAD HOIST CHAIN SLIPPED OFF LETTING HOUSING FALL ONTO FOOT.

WHILE ATTEMPTING TO INSTALL AIR CLEANER UNIT ONE FOOT SLID ON INCLINE OF FENDER CAUSING HIM TO FALL ONTO HIS BACK MUSCLES IN LKOWER BACK WRENCHED